WRT54G Very Slow connection speeds away from the router

I have installed my router in the living room. The connection speed is perfect in the living and dinning area , as we move away from the router to the inner rooms (bedrooms) the signal strength remains fine (very good) but slowly the internet speed drops untill it stops. The signal strenght still shows as very good. Doing a "repair" - switch off and "switch on" - on the laptops wirelss adapter brings back the connection speed for a while before it falls off again.
Any suggestions for this prob please!!!

Make sure that the firmware on the router is up to date. If not then download the Firmware from the Linksys web site. Connect the computer to the router with the Ethernet cable. Open the setup page of the router. Got o Administration tab and click on firmware upgrade sub tab. Upgrade the latest firmware on the router.
After upgrading the firmware, it is recommended that you should reset the router and reconfigure the router.

Similar Messages

Help : very slow connection speed with AEBS and iMac

I connect to the internet using my newly purchased AEBS. I have a MacBook and an 24" iMac ( purchased in Nov 2007). My iMac showed very slow connecting speed of <1 MB/s download; with my MacBook placed just 1 foot from my iMac, the MacBook showed an amazing download speed of 20MB/s. If i connect the iMac to the AEBS using ethernet cable, it can get a very high speed.
So, where is the problem??
I am new to wireless, please help. I use iMac more than my MacBook at home.
Actually, i did not touch the any of the advance setting of the AEBS.

You know, I am experiencing the same problem. My wife's PC and iPhone are blazing fast, but my MacBook is accessing the internet at about dial-up speeds. Very frustrating and I haven't yet found the culprit.
Anyone???

I upgrade my iPhone 4 to iOS 6 and if I'm close to my router the signal indicator comes on and the phone connects to the wifi just fine, but if I step away from the router my phone does not have signal and cannot connect to Internet

i upgrade my iPhone 4 to iOS 6 and if I'm close to my router the signal indicator comes on and the phone connects to the wifi just fine, but if I step away from the router my phone does not have signal and cannot connect to Internet

I can use my iPhone only with wifi .
I don't get any signal and I can not connect to
The Internet without wifi.
When I don't use my wifi from home I have lost all connection to the net
My iPhone is on and working it does not shut down

Mavericks install incomplete. No Apple installers on HD. Will I be able to upgrade to Yosemite and will it fix all that didn't install with Mavericks upgrade? Very slow connection speeds 30 hrs to download Mavericks. Tried re-install; no help/

Ever since upgrade to Mavericks I have been having problems which are too numerous to mention. I finally found a program from a UCBerkley professor called Pacifier which indicated 4000+ of 400,000+ files and folders did not install. I was unable to go further to try to fix everything because Pacifier can't find ANY Apple installers on my HD. It recommended I download the Mavericks installer without reinstalling to continue; however, after having done so (very slow connection; takes 30 hours to download) and although the installer appears in apps while downloading it disappears and NO Apple installer packages can be found on my hard drive. I tried to download Yosemite once and it indicated my system wasn't eligible for the upgrade. Its' download time was similar to Mavericks; 28+ hours.
I am using a Macbook Pro mid-2012 version OS X 10.9.5 (13F34); Processor 2.5 GHz Intel Core i5; Memory 4 GB 1600 MHz DDR3; Graphics Intel HD Graphics 4000 1024 MB.
Regardless of how many files and apps I remove my memory is being eaten up to the point I can hardly do anything at all. There are no civil words for how frustrated I am. Someone please help me.
Thanks,
JJ

Install Mavericks, Lion/Mountain Lion Using Internet Recovery
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Internet Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
Partition and Format the hard drive:
Select Disk Utility from the main menu and click on the Continue button.
After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
This should restore the version of OS X originally pre-installed on the computer.

Very slow connection speed

Very slow internet speed past 10 days. Have completed 1) VIOS recommended optimizer; 2) speed check (3.1 down, time out on upload); 3) diagnostic check (never completes analyzing); 4) turning router and devices off/on. Any other suggestions appreciated. Thanks

PLEASE NOTE MY LOCATION.
MY FiOS SERVICE MEETS MY NEEDS
Tom
Freedom Essentials, QIP 7100 1,Bose SOLO TV Sound System,,QIP 7216 P2,M1424WR Rev F, iPad 2 WiFi,iPhone 5,TV SYST INFO Release 1.9.5 Build No. 17.45
Data Object 39.45
Attachments:
FiOS Internet Speed Tests 1 5 2014.pdf ‏41 KB

How do you get wi fi on your i pod touch when your to far away from the router

How do you get wi fi on your i pod touch when your to far away from the router

You don't

Very slow connection speed (broadband)

i have done a download speed test and i am only getting between .25mbs and .5 mbs ,according to the bt website test using my phone number it said i should be getting 3mbs. why is there a big difference.
cheers

BT throttles your connection based on what it calls your "IP PROFILE". This is a man-made term for the level of service you can expect from the company.
In simplistic terms, lets pretend they were providing electricity to your house. The Minister of Electricity who is part of the government says to them you have to provide 240 volts.
They say OK, we will do this as long as the customer can take 240v. If we find out that they can only take 8v, then we will only supply them 8v. . . is that OK minister? The minister thinks and says, well if the consumer only has 8v power lines then that is an exception and yes of course you can.
So the supplier looks at their "AGEING COPPER TECHNOLOGY" and employs someone to create a computer program that monitors what electricity it think is sent to the customer.
The customer not knowing about electricity decides the company should know what is best for them and waits patiently.
Next day, the customer turns on a 240v light bulb in their house and only a glimmer occurs. A glimmer that Hubble (the space telescope which see's stars 4billion light years away) has difficulty detecting just 4cm away.
The consumer complains. . . why isn't my light bright?
The company says, we value you as a customer and based on your usage and connection details rate your property only to accept 2V. The government says this is ok. . . here is the white paper on providing a satisfactory level of service and it clearly states we have met our obligation. So can we have our £57 per month off you otherwise we'll be forced to take you to court and sell your house and potentially throw you in jail.
Sounds familiar?
Owlie

Very slow connection speed, after phone line probl...

My catalogue of problems starts about a month ago. The phone line developed heavy interference and my Broadband connection kept dropping. This was diagnosed as being a fault with my HH 1.5. BT duly sent me a replacement HH3 which arrived about 3 days later. I installed the new hub, changed all the wiring and the filters for the new kit that came with the hub only to discover that the interference on the phone line was now even worse. It was so bad that at times you could not even hear what was being said on the other end of the phone, so an engineer visit was arranged.
A week later a BT engineer came and checked the line, sure enough there was a second problem and all the wiring from my house to the nearest telephone pole had to be replaced.
These problems had had a catastrophic effect on my connection speed and profile (I was getting about 500 kbps both up and down stream), so I dutifully reset the hub after the engineer had finished and waited for the line to stabilise.
14 days later and the upload speed had doubled, but the download speed is still unchanged at 570 kbps, about half the current upload speed. The line was a bit temperamental for the first few days but I have been able to maintain a solid connection for the last 4 days, current stats are as follows:
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
4 days, 04:42:16
Downstream:
574.3 Kbps
Upstream:
1.184 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
29.9 dB / 5.6 dB
Line attenuation (Down/Up):
19.6 dB / 12.8 dB
Output power (Down/Up):
18.3 dBm / 12.4 dBm
FEC Events (Down/Up):
279 / 615
CRC Events (Down/Up):
0 / 94
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 156
Error Seconds (Local/Remote):
0 / 42
There is only one active socket in the house, and the hub has been running from the test socket for the last week.
Solved!
Go to Solution.

The Hub is connected to the test socket. Disconnecting the ADSL feed to the hub has had no real effect (The upload speed increased marginaly but still no change to the download speed). Reran speedtest too, the new stats are:
FAQ
1. Best Effort Test: -provides background information.
Download Speed
0.44 Mbps
0 Mbps
0.5 Mbps
Max Achievable Speed
Download speedachieved during the test was - 0.44 Mbps
For your connection, the acceptable range of speeds is 0.1 Mbps-0.5 Mbps.
IP Profile for your line is - 0.51 Mbps
2. Upstream Test: -provides background information.
Upload Speed
0.94 Mbps
0 Mbps
0.83 Mbps
Max Achievable Speed
Upload speed achieved during the test was - 0.94Mbps
Additional Information:
Upstream Rate IP profile on your line is - 0.83 Mbps
ADSL Line Status
Connection Information
Line state:
Connected
Connection time:
0 days, 00:02:29
Downstream:
574.3 Kbps
Upstream:
1.2 Mbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
29.9 dB / 5.9 dB
Line attenuation (Down/Up):
19.5 dB / 12.7 dB
Output power (Down/Up):
18.3 dBm / 12.4 dBm
FEC Events (Down/Up):
0 / 0
CRC Events (Down/Up):
0 / 0
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 0
Error Seconds (Local/Remote):
6 / 63

WRT54G3G-ST very slow connection speeds

Hi,
I recently purchased a wrt54g3g-st router for mobile broadband and I have had some problems with the connection speeds. I have called linksys support but they were no help. I am using a PC-5740 broadband card which works perfectly fine in laptops by itself. When I am connected through the router its shows that I have 54.0 Mps speed but the pages load about as slow as dial-up speeds
Thanks for any help you can give me on this problem

if loading the pages is the only problem then try adjusting the mtu settings on the router ui to 1392 ....

My laptop will no longer stay connected upstairs away from the modem..... what can i correct as it did proior to a worm issue

I was reading email.... and got a worm... avg and malware got it... I called microsoft and they also finished cleaning up the mess from the worm... But now the laptop will not hold the internet signal for more than a minute or two before it disconnects and i have to restart it.....What can i do

You clearly did not notice that you have joined a USER TO USER COMMUNITY FORUM
This is NOT Apple ,Apple do not read nor do they therefore respond
So if you would like to wind your neck in ........................
try a reset of iPhone and then a restore,best, as new and if it then functions correctly try restoring with your backup

Very slow connection even after upgrading firmware router WRT54G2 v1.5

Hi,
My connection is very very slow, even after upgrading firmware of a router WRT54G2 v1.5. I use a Mac, and Mac OS X 10.5.8.
I have also re-set the router and configured but it didn't work. Any other alternative to speed up my connection? Thanks!!

On the setup page,reduce the MTU to 1400,Under the Wireless tab..Wireless Network mode should be mixed...Provide a unique name in the Wireless Network Name (SSID) box.Set the Wireless channel to 11-2.462GHz...Click on Advanced Wireless Settings...Change the Beacon Interval to 75,Fragmentation Threshold to 2304,RTS Threshold to 2304.
Now,reboot the router and check...

Slow Connection speed at all times, with regular d...

I would really appreciate any advice you have to offer! (P.s Connection time is so low because I recently connected the router to the test socket to see if there was a problem with my internal wiring)
I've been experiencing a slow connection speed (even though the router is connected to the master socket) much slower than with my previous provider and a very intermittent service. The broadband connection seems to drop out every time the landline is in use and when using the landline you can hear a lot of static/crackling in the background.
Connection Information
Line state:
Connected
Connection time:
0 days, 01:32:51
Downstream:
1.12 Mbps
Upstream:
444.9 Kbps
ADSL Settings
VPI/VCI:
0/38
Type:
PPPoA
Modulation:
G.992.5 Annex A
Latency type:
Interleaved
Noise margin (Down/Up):
5.4 dB / 8.6 dB
Line attenuation (Down/Up):
29.6 dB / 14.8 dB
Output power (Down/Up):
19.4 dBm / 9.9 dBm
FEC Events (Down/Up):
1412 / 0
CRC Events (Down/Up):
0 / 32
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
HEC Events (Down/Up):
0 / 131
Error Seconds (Local/Remote):
12 / 15
Test1 comprises of two tests
1. Best Effort Test: -provides background information.
Download Speed
937 Kbps
0 Kbps
1000 Kbps
Max Achievable Speed
Download speedachieved during the test was - 937 Kbps
For your connection, the acceptable range of speeds is 400-1000 Kbps.
Additional Information:
Your DSL Connection Rate :1146 Kbps(DOWN-STREAM), 444 Kbps(UP-STREAM)
IP Profile for your line is - 1010 Kbps
I would really appreciate any help and advice! (P.s the connection time is so low because I tried to connect the router to the test socket to check if the fault was with the wiring. The router is normally on 24/7 and these problems still occur)
Solved!
Go to Solution.

Hi and welcome to the forum.
Have you tried another known working telephone into that test socket without an ADSL fiter.
If you have done all that you will need to report to your comms provider, if its BT Retail you will need to call them on 0800 800 151 or 0330 123 4151 from a mobile phone.
They will mention about charges but as long as you have done as suggested and you have not damaged any of the incoming wiring there "should" be no charge. when you phone do NOT mention broadband once any noise on your line is solved then your broadband will improve
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

WRT54GS VERY Slow Internet?

Well, We bought a router about 3-4 months ago, when my sister got her a laptop and I got a Nintendo DS. About a week ago, the internet on the main computer downstairs (the router/DSL box is RIGHT on top of the computer tower, so it isn't a interference or something problem...) Now, from about 2-9 pm, the main computer (one with box right on top) has the internet loading so it takes about a minute for a page to load, and 20 min for a 1 min video on youtube to load. So obviously, that's a very slow connection. Today, I try my Nintendo DS to test the connection, and even with just 2 bars, as it's upstairs (theres 3 bars total on DS), it was running the normal speed it always does. My sister on her laptop (which is even farther away from the router, on the other side of the house upstairs) says her internet is working perfectly fine.
Anyone know what could be causing this? I have rebooted the router multiple times, upgraded the firmware, and done everything else the automatic support says.

Are you saying that your wireless router is sitting on top of your computer, and that very same computer is connecting to the router wirelessly ?
If so, why don't you just turn off the wireless in your main computer, and connect an ethernet wire between it and your router ?
Also, you really should not keep your router on top of your computer. Try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Hope this helps.

WRT160N SLOW CONNECTION SPEED

I have slow connect speed when using the WRT160N. I have tried every thing, done dianogstics on connection, router, modem, thru three diffeant software, norton, windows, system machinics. when ising the router some days the speed is amost like using dial up
I use XP, on both a laptop desk top, up to date drivers, both cna use wifi or direct connection by cat 5e, 3 m of ram, a wimax internet server,,,,, (company called Bridge Maxx)
But when I stop using the router and connect directly to the modem no problem works fine,,,,, not sure what to do........ just need my wifi back,,,,so i cna work,

Whats the Version number of your Router, If you have having version2 router, then there is an knows issue with Version2 Router. Downgrading to Build 8 is generally accepted to correct these issues, however Linksys have indicated to several people they do not have the build 8 firmware to give to end users.
This is ONLY for WRT160N V2 routers. This firmware will not work on WRT160N V1.
You can find it at http://audipages.com/router/
Follow the dowload and firmware downgrade instructions on that page.
Once you upgrade the firmware of your router, you need to Reset your Router and Re-Configure all the settings on it back again. Once you do the settings on your router i think this should solve your problem.

Re: WRT350N ----- Very poor Wireless signal strength from my router

I have a WRT350N router. I had it for a year now. In the begining the Wireless Signal strenth was good.
I used to get 4-5 bars in my bed room which is about 10 meters from the router.
Now I have my laptop sitting 1 feet away from the router and I get only 1 bar.
I upgraded my firmware. I rebooted my router a few times still no luck.
Current Firmware Version: v1.04.4 build 003 Jul. 14, 2008
Can any one tell me whats the problem. More importantly can some one help me resolve this problem.
Thanks
Sunny

As you upgraded the router's firmware,I would suggest you to reset the router for 30 seconds and reconfigure it from the scratch, as it is advisable to reset the router after upgrading the router's firmware.
On the router's setup page,Under Wireless tab..Give unique name in the Wireless Network Name (SSID). Change the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz... Under the Advance Wireless tab,change the Beacon Interval to 75 and click on save settings.... Now,check.

WRT54G Very Slow connection speeds away from the router

Similar Messages

Maybe you are looking for