WRT54G Wireless G--Pressed Cisco Logo by Mistake

I've had my WRT54G working perfectly with my home network, now I was dusting off my computer and by mistake pressed the Cisco Systems button on the router.  It started to flash bright white and then stopped.  I haven't reconfigured my router in awhile so do I have to start remembering how to reset my passwords etc. I called Linksys and they wanted to sell me an extended warranty in order to help me deal with a possible reset where the router might be looking for a new firmware after pressing this button.  So far the router and my settings are fine.

If you press the Cisco Logo on the Router, this will change the Wireless Settings on your Router.... It will create a New Wireless Network Name and a New Security Key....If you want to change the settings on your Router follow the setps bellow.. 
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...(If you have changed the Router password you can use that password to login to the Router setup page).
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Similar Messages

  • New WRT54G wireless router. Who's the genius that can help me?

    I just purchased a WRT54G wireless router. The main reason is my son wanted to be able to use his Sony PSP online. I also have two desktop computers that will be wired thru this router. My question's are. If he is using his PSP online and the desktops are wired, can the desktops be "hacked" if they are on/off? If the router is turned off then the wireless is not working? If I access the router and disable the SSID Broadcast then the wireless portion of the network is off? What are the safest security settings to protect my network?
    Thanks.

    Dead Mans Zone....  I guess.
    Using the DMZ is a very simple and risky way to forward ports. The DMZ takes an ip address of a computer on your network, and forwards all ports to that computer. This is really nice if you are having problems forwarding ports for some program. It can be a life saver if your router will not allow you to properly forward ports. It also has a huge downfall. The computer that is in the DMZ is now wide open to internet traffic. Meaning that it will catch virii, and it will be at risk of being hacked. If you put a computer into the DMZ then please install a software firewall to help protect it
    Orange/White. The Cisco logo is the Router’s SecureEasySetup button. It lights up and will stay orange when the Router is powered on. The color orange indicates that the Router is not using the SecureEasySetup feature, while the color white indicates that the Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup mode, the Cisco logo will turn white and start flashing. After the Router has generated the SSID and WPA-PSK (also called WPA-Personal) key, the Cisco logo will stop flashing and stay white.
    Message Edited by wehowardjr on 12-30-200611:26 AM

  • Problem with wired computers on a WRT54G wireless router

    I have a WRT54G wireless router that has been working flawlessly up until now.  On Sunday, my son informed me that his computer, which is wired wasn't connecting to the internet.  Upon further investigating, we found out that our wired computer in our gameroom wasn't connected either.  However, our main pc, which is also wired, was connecting just fine.  I checked my laptop and several other wireless devices and they were online as well. 
    Here's the weird thing.  In my gameroom, I have just one cable coming into the room from the router.  That cable connects to a 5 port switch which then connects to my gameroom pc, Xbox 360, and Playstation 2.  I checked my Xbox 360 and it connected to Xbox Live as soon as I turned it on so that told me that I had connectivity coming from the router and the switch.  But why was the pc not connecting? 
    Anyway, I restarted the router, but that didn't fix the issue.  I then restarted my cable modem, a Motorola Surfboard, and the router and the issue was resolved.  All my pcs were connecting again.
    Everything was fine until yesterday when the exact same issue occurred.  This time the modem and router restarts did not fix the problem.  Again, I have connectivity coming from the router to the 5 port switch because my wired Xbox 360 connects just fine, but my wired pc does not.  My son's wired computer is not connecting, but my main pc is.  I cannot figure out how to resolve this issue.

    Might be possible that the router need reconfiguration ... So reset the router...for few seconds ... after reset ... Please access the setup page of the router by launching an Internet Explorer and type on the address bar, 192.168.1.1 and press enter. When it prompts for the username and password, leave the username field empty and provide password as “admin "" all in lower cases and then click on ok. On the main setup page the ""Internet Connection Type"" should be on ""Obtain IP Automatically - DHCP “. Click on the Save Settings button. Now click on the sub tab ""MAC address clone"". - Click on enable - Click on clone your PC's MAC button and then click on the Save Settings button. Power cycle the network again & see if it works ...

  • Linksys WRT54G Wireless-G Router Not working

    I have a Linksys WRT54G Wireless-G Router and it has worked good for a couple months and yesterday it stopped. When I plug it in all the lights are lit even though there arent any ethernet cables connected and the power light blinks constantly. I tried holding the reset button on the back and it didnt help. Anyone know whats wrong or anything I can try to fix it?

    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • WRT54G wireless router irregularly drops connection

    I've had a WRT54G wireless for about 3.5 years now, with a Motorolla SB4200 cable modem connected to it to provide internet service. The router itself is connected to a desktop PC and there are two laptops that are connected to it wirelessly, one of the laptops is old and has a Linksys PCMCIA wireless card and the other laptop has wireless built in to it.
    I updated to the latest firmware for the router.
    For more than a year now, the wireless connection has been irregularly dropping. Sometimes it will reconnect instantly, sometimes it will take a few minutes to reconnect, sometimes it will take up to 10 minutes. More importantly, the connection drops very irregularly. Sometimes it will work for weeks flawlessly and sometimes it will constantly drop several days in a row.
    Today I haven't had any problems so far, but yesterday and the day before, it was dropping a lot. What I've noticed is it mostly happens in the evening, so I'm assuming maybe there is some kind of interference.
    I have been told that wireless routers do have a limited lifespan and that mine probably is just wearing out and needs to be replaced, so I picked up a new WRT54G router for $50 yesterday, however, I haven't opened it yet.
    Is it likely that my router is just wearing out and needs to be replaced, or is there some kind of interference going on? I am able to pick up a number of different wireless signals from the neighbors, but they are always there. Even right now as I am connected to the network typing up this message.
    Any feedback would be greatly appreciated.

    Thanks for all your help wehowardjr.
    I haven't actually pressed the reset button in a while, but I did unplug it for about 20 seconds then replug it just two days ago.
    What is the nvram and exactly how do I clear it? I don't think I've ever doe that.
    I use a laptop that has the wireless built in and I'm the one who uses the computer the most in the house, so I am the one who is noticing the connection dropping the most, so I'm not really sure if it is the problem with the laptop witht he PCMCIA card.
    I'm surprised version 6 has problems. I would have assumed that it would be a great improvement over previous models, especially 1.0. I guess I should return it to the store then? Isn't there version 7 out now?

  • SPA525G stuck on the Cisco logo screen

    Hi
    I updated the daylight savings dates on a Cisco525G2 and after restaring the phone now hangs at the Cisco logo screen.
    It goes through the start up, lights come on, the screen flashes and the cisco logo appears. And thats as far as it goes.
    I have tried continually pressing the speaker key but it has no efffect.
    I am running firmware 7.5.3
    Does anyone have any ideas of where to next with this problem?
    Thanks in advance
    Peter

    Syslog and debug messages catched during boot of device may help substantially.
    See and

  • Cisco Logo button Lit?

    This may be a dumb question, but I can't find an answer anywhere else. I have a WRT54G V3. I just upgraded the firmware to 4.30.5 and now the Cisco logo button on the front of the router is lit up orange. What is this button and why is it lit up?
    Greg Walter

    You dont need to do anything with it.  The firmware update made the Cisco button active, thats all.  Nothing to worry about.

  • Switched from DSL to CABLE. WRT54G Wireless Router stopped working.

    When I switched from DSL to CABLE, my WRT54G Wireless Router stopped working. I am not able to access the router page (192.168.1.1) Also, when I use the set up CD for re-installation, the wizard aborts in the middle saying it can not connect.
    I appreciate any help to resolve this problem.
    P.S. The router acts like a one-port wired router. 

    Here is my favorite method for resetting a router to factory defaults, and trying to get it working again.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.

  • My iphone was stolen, I used find my iphone app, and found that it was offline, however when tried locking mode option, I pressed remove device by mistake. Is there any way I can restore the iphone to my icloud/ apple Id again? No manual backup on laptop

    My iphone was stolen, I used find my iphone app, and found that it was offline, however when tried locking mode option, I pressed remove device by mistake. Is there any way I can restore the iphone to my icloud/ apple Id again? No manual backup on laptop

    The phone will automatically re-appear when it connects to the Internet. However, don't get your hopes up, as thieves know this & will make sure your phone never re-connects so you can locate it.

  • WRT54GS WIreless not connected, yet connected

    My WRT54GS wireless connections wont go through, as it clearly says, Not Connected, yet my network connections will show that I am connected to the internet and indeed, I can browse the web. My biggest problem with this is that eventually (around 10 minutes or so) it will disconnect from the internet, which is a problem since i play online games. Anyone ever had this happen?

    under the network connections , what all connections do you see....ensure that any other connection except for the wireless network connection is disabled..
    the only medium of connection should be the wireless network connection... check this and let me know if more help need on this issue ...

  • HP Officejet Pro 8500 wireless Networking with LINKSYS WRT54GS wireless router

    I have a HP Officejet Pro 8500 wireless printer conneted via WiFi to my LYNKSYS WRT54GS wireless router.  I do not have a USB cable or ethernet cable plugged to the printer.  I am able to use the 'scan to email button' and the 'scan to network folder' button on the front of the printer and I can pint from the PC to the printer with no problems.
    I installed the HP printer software from the CD, choosing network/wireless connection, without having to install any USB cables from the PC to the printer in the process.  many posts in the forum mention having to connect USB cables in the wireless installation process.
    Can I install the software in the same fashion on the other two laptops? Or, do I need to do something differently?

    The USB cable is used on those printers which do not have display or front panel wireless setup is not possible. We configure the wireless settings during install and save those settings in printer's memory by transferring through USB cable. Therefore the USB is plugged in during wireless installation temporarily. In your case I don't think plugging in USB cable is necessary as the printer is already on network and had IP address. Connect the laptops on wireless network and proceed with regular install, the printer should be detected automatically.
    Thanks
    Naveen K
    HP Support Engineering Center
    Click on BLACK STAR button to say thanks
    (Although employed by HP, I'm trying to address the issues with my sole willingness and my employer does not bear any liability for my responses)

  • Does the Xbox 360 wireless adapter even work with the WRT54G wireless router?!!? If so, how???

    I just bought a WRT54G wireless router (Ver 8.0; firmware updated to latest).  I have successfully connected my wireless laptop using WEP security, but I'm at wits end trying to get the Xbox 360 wireless adapter to work.  (It worked just fine with my Netgear router until that router recently died.)
    When I do the "Test Media Connection" routine (you XBox 360 users know what I'm referring to), the Xbox immediately recognizes the Network Adapter and indicates that it is connected to the Wireless Network, but it inevitably fails the next step in the process:  IP Address.  I have the set-up for the IP address to be assigned automatically by the router (which is set for  DHCP Server enabled).
    I have gone around the mountain innumerable times myself and then with well-meaning friends who say try this, try that, try this, try that.  I've had to re-establish my laptop set-up so many times I wanna scream!
    Are the Xbox 360 wireless adapter and the WRT54G even compatible?  If so, what am I missing here?  I'm not too technical and obviously in over my head, but this ought not be that hard.
    Please, please do NOT respond unless you KNOW the answer!  I don't mean to be curt, but I'm over / past "suggestions to try."
    Thank you VERY much for your time and consideration if you can help me.

    I don't think that the X-BOX adapter is not compatible to wireless rotuer .... there are few settings you can try on the router ... Access router setup page ... Please click on the tab "Application and gaming" and click on sub tab "Port range forwarding" 1) On the first line in Application box type in "Xbox", in start box type in 88, in end box type in 88, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 2) On the second line in Application box type in "Xbox", in start box type in 3074, in end box type in 3074, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 3) Now save the settings 4) Once you return to the setup page, click on the tab "Administration" and disable the UPNP and save the settings. 5) Now assign the given ip address on your xbox ip address :- 192.168.1.20 subnet mask :- 255.255.255.0 default gateway :- 192.168.1.1 Please assign the dns address on the xbox primary dns :- 4.2.2.2 secondary dns :- 192.168.1.1 6) Please try to test your xbox live. Hope it works ...

  • I recently bought a WRT54G wireless router along with a W...

    I recently bought a WRT54G wireless router along with a WUSB54GC compact wireless adapter and set up both products as directed.I get a message saying connected to the access point but cannot find internet. While connecting to my internet directly,(using a fiber optic cable with no modem necessary)it connects to the internet however using the modem,wired or wireless it still gets the same error. I am not computer literate,so i don't understand abbreviations or where to go to input information into certain areas,so if anyone could help me with step by step information I would be very grateful. Thank you and happy holidays.

    Let me know the Model number of the adapter & the operating system of the computer ......so that i can assit you further ... ..

  • WRT54G wireless not working after upgrading to windows vista, please help

    Hello everyone....
    I have a few problems. I upgraded to Windows Vista and cant seem to get my wireless internet working. My router is WRT54G wireless-g broadband router. Ever since I upgraded Vista my xbox 360 will not connect.
    I just bought a new wireless web camera and that does not work either because the wireless is not working.
    Any suggestions on what I should do to solve this issue?
    I noticed when I goto 192.168.1.1 my firmware version is Firmware Version: v3.03.9 does that have anything to do with it? Is there a more up-to-date version that will help?
    Hope to hear from someone.

    I have the same problem, and so does my son, he has a toshiba satellite new laptop and I have an acer new laptop, both have Vista on them, and my wife has XP and has no problem getting on teh router, but i have this problem everyday.
    Eventually it will all of a sudden show up and connect and start working, then if you laeave your computer in standby movde overnight, it will still work in the morning, but if you shut down comeplety you will lose the connection for who knows how long. what is the fix Linksys?
    (Edited post for guideline compliance. Thanks!)
    Message Edited by JOHNDOE_06 on 12-28-2007 07:28 AM

  • Hi,   I just bought a linksys WRT54G Wireless Router. My...

    Hi,
    I just bought a linksys WRT54G Wireless Router. My laptop was able to detect it wirelessly untill I changing the "Router Name" in the setup page(http://192.168.1.1)
    While saving the settings, the wireless network suddently disconnected. From that point onwards, I was not able to detect the wireless network with any computer at all.
    I tried unplugging it, resetting it, and even restory factory settings by holding the reset button for aprox 30 secs.
    What is wrong?
    Thanks in Advanced

    Recheck the wireless setting (SSID, encryption, DHCP, etc) on router management page again. Also make sure your computer's wireless adapter setting matches the one you set on router.
    picoHat
    Home Network, Wireless Network and Computer Networking Made Easy

Maybe you are looking for

  • Looking for a replacement cd

    Can anyone tell me where I would go to find a replacement cd that has Airport utilities version 5 with bonjour

  • Help me a simple problem

    [hello drawAtPoint:location with Font:font] hello type is NSString ,but NSString not have drawAtPonit fuction,why?? please explain it,thanks!

  • PSE7: Find all photos with any caption?

    I'm running PSE7. I have a sub-set of my images selected via a tag. Now I want to find all of images in that set that have any caption at all. So I do a Find/By Caption or Note. Now in the next dialog box is there some way that I can enter a wild car

  • Why is my new printer is unrecognised?

    Hi there, I've just installed the driver CD for my new Canon MG 5350 printer and connected it to my wireless router.  Everything went very well, no error messages or problems were encountered and the printer indicates a steady connection.  My iBook G

  • ORA-24123: feature IOT support is not yet implemented

    Hi, in 10G R2 when using DBMS_REPAIR I receive : ORA-24123: feature IOT support is not yet implemented ORA-06512: at "SYS.DBMS_REPAIR", line 293 How should I implement SYS.DBMS_REPAIR ? Thank you.