WRT54G2 and Iomega Home Media Network HDD

So I am on my second HDD with Iomega. I am thinking now that this is a router problem rather than a HDD problem. I have a 1TB Iomega home media network drive, eversince I bought my router and began using it I have been unable to use my HDD. It is hard wired to the router via RJ-45 cable and both units have been reset and powered up in about every order you can imagine. I have reset factory defaults on the router and made security changes to ensure there was nothing blocking that port. I am at wits end. I cannot connect to the HDD and the drive flashes yellow and blue indicating it cannot estabilsh or receive an IP address from the router. Can anone help me with this. The drive has already been replaced once after the same symptoms occurred previously. Any help is appreciated.

Per the Iomega support site:
How do I find the Home Media Network Hard Drive on my network?
Install the Iomega Home Storage Manager software. Once the installation completes, the Iomega Home Storage Manager icon will appear in the system tray (Windows) or Menu Bar (Mac) and your computer will automatically be connected to the Home Media drive's shared folders.
NOTE: If no DHCP server is found on your network the Home Media Drive will get the self-assigned IP address 169.254.55.82.
NOTE: The Iomega Home Storage Manager will automatically scan your network and connect to available shared folders. If you receive a message from your operating system's firewall alerting you of network activity, click the unblock button.
Mac Users: The Iomega Home Media drive's shared folders should mount and appear on the Mac Desktop.
PC Users: The Iomega Home Media drive's shared folders will automatically be assigned a drive letter and will be available in the Network Drives section under My Computer.
Also see the User Manual for the drive or the Iomega online support site.
The network drive has a menu system to allow the user to configure the network settings for the drive.  Log into the drive per the User Manual directions and check the Network settings to ensure the Automatic (DHCP) is enabled. When this option is enabled it should pull an IP address from the router.
One other option is to configure the IP setting to Manual in the Network page on the network drive and input an IP address (Static IP Address) outside of the IP addresses the router will hand out via its DHCP server. You would also have to fill out any additional settings for the Manual option. So for example if the router is configured for IP address of 192,16.1.1, and a starting DHCP IP address of xxx.xxx.xxx.100 and a Maximum Number of DHCP Users of 50 than set the network drive's IP address to 192.168.1.200, or any ending IP number between 151 and 254, or between 2 and 99. That way it won't conflict with the router's DHCP address assignments and it will always have the same IP address.

Similar Messages

  • Just bought and connected iomega home media network hard drive but can't see it on network - HELP!

    so per the information from my other thread i bought an iomega home media network hard drive. i've attached it to the westell ultraline series 3 9100em wireless router i got when i signed up for fios. i installed the software that came with the hard drive but it's not showing up on the network. when i log in to the router management console it shows up as the first device under "network stats". what am i missing that's not letting the drive get recognized on my network? as always thanks in advance for any replies.

    Hello jarmin2411
    A factory reset from the web interface would correct this sort of issue.  However I suspect that using the pin-hole reset button should also be able to clear the issue as it seems to be a network configuration issue.  The network settings may have become corrupt during the update.   Using the device reset button
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • Iomega Home Media Network Hard Drive contents not appearing in iTunes

    I'm running iTunes 10.5.1 on my MacBook which is running OS X 10.6.8
    I've got an iomega Home Media Network Hard Drive ( http://tinyurl.com/l8jmaa ) NAS hooked up to my home intranet, and I use it as the master repository for all my music for iTunes, as I've got multiple computers in the house, and the device (with iTunes and DLNA activated) will show up in the "Shared" section of my iTunes source list, and I can view and play all my music from there.
    Sometime over the course of the last few iTunes updates, however, this functionality broke, and I'm not sure why.  The device shows up in the "Shared" section still, but when I click on it, iTunes shows a message on its screen that says "Loading "Iomega-0557fc" (yeah yeah, I didn't give my drive a spiffy name, I just stuck with the stock out-of-the-box name) and gives me the horixzontal cady-cane, and the little circle spinner spins away to the right of the device in the source list, but iTunes never actually completes the task of bringing up an index of the drive.
    The drive itself is fully functional.  All the settings are proper on it, I can move data on and off from the Finder, I can even drag-and-drop music files from the NAS in the Finder into iTunes and the files will add to playlists and play just fine (I've got "Copy files to iTunes Media Folder..." turned off, so I know they're playing from the NAS) so it's not like there's some kind of malfuction on the NAS itself.  I've also made sure I've got the latest firmware updates and such.
    I'm sure I'm not the only one with one of these drives, and I'm hoping someone else has encountered this issue and figured it out!  Any help is appreciated!

    Hi , I have similar problem..It was working initially and for some reason it stopped. I device shows up on the SHARED , however when I click it doesnt load the songs..however I am able to stream songs from Iomega NAS via other DLNA clients (ace player etc in ipad)...

  • Can't access Iomega Home Media Network HD from my MacBook Air

    Hello,
    I recently bought a MacBook Air that is currently running OS X 10.8.4. This is my first MacBook.
    I have an Iomega Home Media Network Hard Drive, but I can't connect to it. I downloaded their most recent software for Mac (the LSM client for Mac OS 10.6-10.8, version 1.4.3.9580), but keep getting a message saying "The version of the server you are trying to connect is not supported" when I try to access my files from my Mac.
    I tried to find the answers from Lenovo, who bought the Iomega, but their support seems very poor and I wasn't able to reach anyone about it since my warranty has expired.
    I was wondering if some one could please guide me to find a solution to this problem.
    Thank you so much in advance!
    Thais

    Preferably, get rid of that junky device. If you don't want to do that, see below.
    Connecting to legacy AFP services

  • Iomega Home media network drive & Time machine backups

    First timer guys, so go easy. :-)
    I have macbook pro. Upgraded from Snow Leopard to Lion couple of days ago. I have Iomega Home media network drive NAS box which I had setup for Leopard and my backups via time machine were working perfectly. I could also mount the shares on the Iomega box on my macbook. Post upgrade to Lion, I can access the shares on my MAC (over smb) but backups not working anymore. Apparently Lion requires shares to be accessible over afp only. I have confirmed Iomega box is compatible with smb as well as afp shares and I even tried manually mounting those shares using command, still no luck.
    Command I'm trying to mount afp shares & the error -
    bash-3.2# mkdir -p /mnt/backups
    bash-3.2# mount_afp afp://username:[email protected]/backups /mnt/backups
    mount_afp: AFPMountURL returned error -5019, errno is -5019
    bash-3.2# echo $?
    101
    bash-3.2#
    Can't see any references to this error. I see few links that ask to carry out some clumsy steps to sort this out. That's not working either for me.
    On a sidenote, why mac doesn't have /etc/fstab? Any alternatives?
    Appreciate any kind of help here.
    Cheers.
    soulcurry

    Hi,
    Have you fixed your problem?
    I have the same configuration, and I can't finish a backup. Every time, I have the message, "Try again a new backup".
    Thanks
    MacBook pro lion 10.7
    iomega Home media network cloud firmeware: 3.2.3.15290

  • I have upgraded to Lion Os but my Network storage (Iomega Home Media Network hard drive) does not work with Time Machine.  Are there any solution available?

    I have upgraded to Lion  OS only to find that my NAS (Iomega Home Media Network hard drive) does not work.  It tells me that it is not configured.  Are there any solutions .  Have Iomega sorted out the problem?

    Same issue here.  Based on what I can tell, iomega still has not developed a solution to the problem.  See below:
    https://iomega-na-en.custhelp.com/app/answers/detail/a_id/28327/kw/Mac%20OS%20X% 20Lion

  • Iomega Home Media Network Hard Drive network access problem

    Hello all                          Having trouble accessing Iomega media drive ce,web interface is not responding.Iam able to ping ,map and access shares using win7 and winxp systems.Read and writie to shares.Earlier in 2012-13 experienced similar problem,but reimaging using reimager software, fixed the problem.Reimaging didnt destroy data it just reset the user accounts.(atleast in my case).Few days back the problem reoccured.I noticed from my experience, the web interface becomes unresponsive only after enabling cloud with medium or high security.I tried resetting. Also tried to connect drive to pc directly and ran ARP utility.Drive respond to ping(arp provided ip address).,but web interface is still  unresponsive.Also cloud invitation email not working.But device status monitor or reporitng  email works. I periodically receive email alerts about new firmware,time synching.Please help me restore my drive. Drive details:Home media network CE(shipped firmware 3.2.3.15290 ).Current firmware:3.2.8.30031.Storage manager ver. 1.4.4.14439Router infoSL-2750u (tried using port forwarding/DHCP and port forwarding/Static ip).TZO remote access status:Expired.FTPisabledCloud :enabledWarranty status:Active.(13/12/2015).  Thank u  

    Hello dhanse_k,
    For something like this, there really isn't much that I can help with here.
    I'm limited to giving advice and that isn't going to help if you have a verified IP that's not granting access to the UI.
    I recommend starting a support ticket here:
    https://lenovo-ap-en.custhelp.com/app/answers/detail/a_id/18133/session/L3RpbWUvMTM2NjU5MDgxMS9zaWQvSEtSbjZqb2w%3D#phone
    It sounds like your NAS is having issues with Apache and starting a support ticket will enable an agent to assist you with that.

  • HT1364 Iomega Home Media Network Hard Drive, Cloud Edition

    Hi just installed the above and transferd all my music but now cannot play them on my iPad it can see the hard drive in iTunes but will not play any advice cheers Darren

    Hello jarmin2411
    A factory reset from the web interface would correct this sort of issue.  However I suspect that using the pin-hole reset button should also be able to clear the issue as it seems to be a network configuration issue.  The network settings may have become corrupt during the update.   Using the device reset button
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • IOMEGA home media network hard drive security issue - admin password bypass

    Some time ago I analysed the http traffic between the above and firefox so that I could automate the restart process because I wanted to restart the drive about once a week overnight.  This I achieved by writing a simple python program and it seemed to work ok but I stopped doing it after a short while.  Many months later I have returned to this and found that the conversation has changed.  The redirection that used to occur has gone and I can now restart my drive without the need for a valid administrator password and I have done this both from a computer on my lan and also via an external  no-ip free dns domain name.  Note that any attempt to access the drive via a browser still requires a valid password.  My original drive was at firmware level 2.063 and this one (a replacement under warranty) is at 2.064.
    Has anyone come across this problem and has anyone any idea how to fix it?
    Happy to post my python code if required.

    Thank you for the reply.  I followed your advice.  I guess the upgrade worked ok because the device now says its at the right level, it removed the admin password (which I then re-instated) and a robots.txt file has appeared in the FTP folder.  However, a couple of things didn't work as advertised:
    1. When I tried to turn on remote access it just hung and I had to reboot the device.  It subsequently resolved itself after a couple of reboots and when I wasn't looking.
    2. When I tried to access the folders through a browser I was presented with a greyed-out 'public' user, for which I did not have a password, and this only resolved itself when I added a new user, which led to another problem ...
    3. I cleared the passwords on a couple of users because I wanted to change them.  No way could I get a prompt for a new password - followed the instructions in the manual - so I ended up deleting them and recreating them from scratch.
    Now then, has this fixed my original problem?  Not really.  The situation is that when remote access is enabled then my program in its current form doesn't work (but I would need to see if I could make it work).  If remote access is disabled and I get my router to port-forward, say 8000, as 80 to the iomega then my program still works fine and I can do a restart or shutdown without the admin password.
    Obviously now that I have this program worked out I can go on to do other admin tasks remotely.
    I'd appreciate any further ideas you might have.

  • Problems using TimeMachine from two Macs to IOMega Home Media Drive

    Hi,
    This has been driving me crazy for a couple of weeks now, so I'm hoping that someone here can point me in the right direction.
    I have a PPC G5 and my wife uses an iMac. I recently bought an IOMega Home Media Drive and wanted to use it with TimeMachine. I set up the G5 and got that working, but when I tried to add my wife's iMac I've had nothing but problems.
    I tried resetting the IOMega back to factory defaults, deleting and then re-creating the backups folder, using usernames and passwords or a guest account, and nothing seems to work. I occasionally do something that breaks it on the G5 (running 10.5.8) but I have been able, for the most part, to get it working again, but it's never worked from my wife's iMac (running 10.6.2).
    I even tried creating the sparsebundles by hand and copying them in which seemed to work on the G5 but not on the iMac. I thought that the problem might be trying to back up two systems to the same share, but I'm not sure how to split them. Is there a way to create separate backup shares on the IOMega (which seems to connect using AFP even though I've seen references to SMB in some of the forums) so that each system would use its own? Is there a general problem when trying to back up two Macs to the same network share?
    The error that I tend to get is that the "backup volume is read only". On the iMac the current error I'm getting, after creating the hostname.sparsebundle image (oddly enough when TimeMachine tried creating it yesterday it dropped the MAC address...not sure why), is: "/Volumes/backups-1/hostname.sparsebundle could not be created (error 45)."
    Any help would be greatly appreciated, this has been very frustrating.
    Thanks,
    Rob

    Hi,
    You don't want to hear this, but Time Machine does not back up to network drives, except Time Capsules or a shared drive on another Mac running Leopard or Snow Leopard on the same local network. It will often back-up to a USB drive connected to an Airport Extreme, but even that is, technically, unsupported, and may require running a special Terminal command to make it work.
    Here's the official word: http://support.apple.com/kb/HT1733
    You may find some hardware or "hacks" that might make it work, in some cases, to a degree. But use them at your own risk.
    First, since this is *unsupported by Apple,* there's nowhere to go when there's trouble.
    Second, you're risking a future update preventing it from working, and perhaps rendering your backups useless.
    No guarantees, of course, but this might help: https://iomega-na-en.custhelp.com/cgi-bin/iomegana_en.cfg/php/enduser/std_adp.php?p_faqid=22012&p_created=1246919828&p_sid=KBbtj nNj&p_accessibility=&p_redirect=&p_lva=&p_sp=cF9zcmNoPTEmcF9zb3J0X2J5PWRmbHQmcF9 ncmlkc29ydD0mcF9yb3dfY250PTEwLDEwJnBfcHJvZHM9MTAzMSwxMDQzJnBfY2F0cz0mcF9wdj0yLjE wNDMmcF9jdj0mcF9zZWFyY2hfdHlwZT1hbnN3ZXJzLnNlYXJjaF9ubCZwX3BhZ2U9MSZwX3NlYXJjaF9 0ZXh0PXRpbWUgbWFjaGluZQ**&p_li=&ptopview=1

  • "Home Media Network Hard Drive - Cloud Edition": what is it?

    I have a "Home Media Network Hard Drive - Cloud Edition".
    I want to update the firmware (actually, I already did, but may have made a mistake).
    When I go to the support page https://lenovo-na-en.custhelp.com/app/subproduct/p/1031 I find that there are two choices that have names similar to my unit's, but not identical.
    Is one of these actually the same as my model?  If so, which?  If not, how do I get support for my model?  Why isn't this clear?
    PS: These names are awkward, long, and confusing.  So long that I could not put all of them in the Subject.  Too late to change them now.
    Solved!
    Go to Solution.

    Hello HughR
    See the below hotlinks for a picture confirmation of each device.
    If the Home Media (Network Hard Drive) Cloud Edition (HMNHDII) is your device, then you would want to follow the firmware update guide from here.
    If you have the Home Media Network Hard drive (HMNHD) then you should follow the firmware update guide from here.
    From your post it seems you have the Home Media CE, the second generation of home media NAS.  The " Home Media Cloud Edition " link would be the correct link to access the support page for the device.
    The names are long, hence the abbreviation from "Home Media Network Hard Drive - Cloud Edition" to just "Home Media Cloud Edition"
    Hope this all helps!
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • Iomega Home Media drive not recognized through Aiport Extreme

    Using ethernet cable, my new Iomega Home Media drive is recognized when connected directly to my iMac, but is not recognized when connected to my Aiport.
    Any ideas?

    The AirPort Extreme wants to see a drive that is formatted in Mac OS Extended (Journaled). My guess would be that your drive may be formatted for Windows?
    You can reformat your drive by connecting to your computer and using Disk Utility.
    Hard Drive > Applications > Utilities > Disk Utility
    You may also have documentation that came with the drive that furnishes directions for reformatting the device.

  • My finder won't open and my crashes all the time since i install an iomega home media server.....help!

    My finder keeps crashing and documents etc won't show sometimes when it does open. The problems have recently started following the installation of an iOmega Home Server......help

    You might want to take your question to the iOmega website.  The probability that someone here has both that server AND uses the MacBook pro is quite small, whereas the iOmega website selects for those who have the device and own a Mac OSX computer.

  • Suggestions consolidating iTunes accounts, home media network

    Hello, I am not exactly sure where to post this, but much may revolve around iTunes store, etc, so I thought I would try here first. Really looking for advice, sorry for the long entry.
    I am in the process of trying to reorganize, simplify and set up a nice home media/storage network for my wife and I (and kids as they get older) the opportunity to basically use and sync any of our devices/computers so that we all have access to a main music library, movies, etc. Here are my main questions, and the scenario ...
    I have my own iMac
    Wife has Mac Air
    Have Apple TV2
    Will each be getting our own iPod Touch
    Airport Extreme currently used for home wifi network
    External drive connected to Airport Extreme to store all/everyone's media?
    My initial thought is this could function well as a media storage hub that all our networked devices could pull from? Or maybe there is a better option, setup that I'm not thinking of?
    Consolidating two individual iTunes Libraries/accounts to one main one?
    What is the best/cleanest approach? My wife and I each have our own, but are find merging if it is recommended. Is it recommended that my wife or I change one of our accounts/ids so we both now purchase off the same apple id? Then just combine our two separate libraries onto an external drive hooked to our Airport Extreme, and use that as a main media collection? Can that external drive then be accessed by the Apple TV as well as our personal computers? Or what if the kids down the road want their own account, if you don't use a single apple id to purchase content, is it difficult to have a central media driver with everyone's content?
    For eventual syncing into iCloud?
    Is it recommended that we put all devices (whether hers, mine, or kids) to the same Apple ID so all devices have access to all the same material? I'll admit I don't know much about iCloud yet, so this might be a basic question. Or maybe there are still ways to sync all devices even if through different ID accounts so the family doesn't feel I'm 'in complete control' ? Is media stored on an external drive for the network able to sync or be used in the same way by the iCloud service?
    I'll probably have more questions, I hope these made sense, and again, sorry for the wordiness. Maybe its a simple setup, but if anyone has the interest or time to lend some advice on what has worked well for them, I'm all ears. Thank you!
    Mark

    What is the Model no of the NAS..?
    Might be you need to do some settings on NAS..Try resetting the NAS and try to reconfigure again.

  • Problem with Fios TV Central and my Home Media DVR...

    I have had Fios for some time and I'm upgraded to the new 1.6 img. I can see and my vz media center works with the home dvr and the other  stb's can view dvr recordings from the dvr.
    My problem is after logging into the Fios TV Central site it never finds my dvr.....it scans for some time then says there is a problem and to try later. I have done everything (I think) that was required to activate this on my dvr and the tv central site. I've rebooted the actiontec, unplugged and plugged in the dvr stb and the other stb's one at a time with no change.
    Any suggestions?
    Called tech support but haven't heard anything from them.
    Cwmson

    O.k.
    Here's what the tech that came out to the house did.
    We first went through the simple stuff and he called his tech guys which didn't really know what could be the problem since this is BETA.
    Finally he had to leave but came back the next evening to replace the MI424WR router and the DVR.
    He did the router but there system to register was down Friday evening so he had to put the old DVR back and come back the next week.
    He finally came back on Tuesday morning and installed the new DVR and it registered ok.
    Then you have to wait for the Fios TV Central and the DVR to update.....takes a couple of hours usually.
    I finally was able to set up FTVC and it's working both from my computer and from my cell phone.
    IT WORKS!!!!!!!!! Yes!
    I think it was the DVR personally because that was the last piece of equipment we replaced and it started working.
    Cwmson

Maybe you are looking for