WRT54G2V1 Need Open NAT for Destiny PS3

I currently have a Linksys WRT54G2V router. My Playstation3 has a wired connection to my router. With my current settings when I play Destiny on my PS3 I have a moderate NAT, and would like an open NAT. My ISP is Charter Communications. I do get a public IP through to my router, and have tried portforwarding. Am i missing anthing? Do i just need a better router?

Internet Service Provider and Modem Configurations
What ISP Service do you have? Cable or DSL?
What ISP Modem Mfr. and model # do you have?
What ISP Modem service link speeds UP and Down do you have?
Check cable between Modem and Router, swap out to be sure. Link>http://en.wikipedia.org/wiki/CAT6 is recommended.
Check ISP MTU requirements, Cable is usually 1500, DSL is around 1492 down to 1472. Call the ISP and ask.
http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=88e63d78588142e6bb68e22d7faf2046_Configuring_the_M...
If the ISP modem has a built in router, it's best to bridge the modem. Having 2 routers on the same line can cause connection problems: Link>http://www.practicallynetworked.com/networking/fixing_double_nat.htm and http://computer.howstuffworks.com/nat.htm If the modem can't be bridged then see if the modem has a DMZ option and input the IP address the router gets from the modem and put that into the modems DMZ.

Similar Messages

  • How to Open NAT Type on PS3?

    How do i open NAT Type on PS3
    Need help

    When you run the network test on the PS3 what is shown?  what NAt type?

  • How to open NAT for Linksys E1000 on PS3?

    question in title:
    it seems as though my gameplay on my ps3 has been very THICK(lag and delay on screen), I have tried changing the MTU and some other options and I already notice the difference but i think I can maximize my lag-free gaming if I completely open up NAT on my PS3.
    Does anyone have a great guide that works?
    Also would changing the MTU/ Disabling UPnP and unchecking anonymous internet requests effect my Download/Upload speeds or anything else, or does it just help fix gaming lag?
    Input towards topic and questions i've mentioned will be greatly appreciated,
    Thanks.
    Greg 

    disabling the WMM has something to do with the support you get from the servers  and from i was told that's not needed to be enbled it should be disabled, and by the way the linksys support team explained it's better disabled instead of enabled and it wouldn't hurt to get a actual gaming router .. i went with the E3000 and i ended up having to ship it back  for some defective that i didnt even cause, i would look into a actual gaming router that supports gaming like the e3000 or the e3200 , it should said for gaming consles or something like that but i will totally look into your problem personally and go from there! intil then i would try to get in contact with playstation gaming system and  figure out what ps3 ports are so you can go from there - there should be a way to test the nat type (there  3 nat type's on playstation 3 )  there's nat type 3, there is nat type 2 (which is open)  and there is nat type 1 and the one we want is the nat type 2 i believe, which means open nat type (meaning plug and play enabled and open ports  on the router )

  • Need an open NAT for 3 consoles and computer

    Have 2 Xbox 360's Ps3 and cant get aOpen NAT on any of them. I have done what I needed to do for the open but both xboxs read Moderate or strict Nat rating and the same for the Ps3. I need help. I am using a E1000 Linksys Router.

    Well it is not recommended to play two (2) Xbox 360® units on the same network connected to the same game server since the modem will only generate a single WAN IP address. But still you can do certain settings on router to make (2) Xbox 360 working. 
    Here is the link which can help you in opening NAT: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=23787&userrole=Links... 

  • 2 xboxes or ps3's with open nat for the rv042? yes i can!

    i signed up specifically to tell future and current rv042 users that after a year of muckin' around with this fairly advanced networking technology, i've finally discovered how to open the nat types of 2 xboxes, instead of one being open and all others being moderate or strict. i'll break it down simply, 3074 port forwarded for the one, and dmz host for the other one. i couldn't figure out for the life of me, why the dmz host wouldn't open the nat type of the 2nd xbox at first, thats when it dawned on me that xboxes aren't capable of understanding the rv042 dmz host. so i tested the dmz host on my computer and it worked, putting my computer wide open to all ports on the internet. so what i tried was internet connection sharing, plugging my xbox wired into my computer which is set as the dmz host. i was all excited, jumping up and down for joy when i had succeeded in what took me an entire year to figure out. why so happy, do you ask? i don't think all of you know just how painful it is to not be able to open the same port more than once on the same network, very, very, aggravating. if you are having the same problem and don't understand how to do what i've explained, just ask. i cannot stand the thought that there are others out there like me that haven't been able to figure this out, it just causes me more pain. i will help.

    I am having the same issue.  My roommate and I both have our own copies of MW3 and our own xbox 360's connected to the same router/modem. We have Verizon Fios and the modem is an Actiontec MI424WR. We have no problem playing at the same time online as long as we are not in the same match. However, when we try to play in the same match, we can never get into a match. It just keeps cycling through the "searching for matches screen.  We were at one point having issues with the OPEN NAT type but that has been solved, don't have me how, it just started working after I set the router back to defaults and we haven't had issues since.
    I tried the link above, but that doesn't seem to help my issue and I think you are having the same issue has me.  If you figure it out, please let me know.

  • Open Nat for WRT54GSV4

    Ok i been tryin to get my NAT set to open for MW2 for abit now but cant seem to figure out what the problem is. Can anyone please help me with opening the NAT for this router for Modern Warfare 2 on the PC, not Xbox or PS3.  Any help would be appreciated thanks.

    Honestly ive never had to mess with my routers ports before and honestly dont know exactly how to do it right. I know where to go in the routers settings im just abit foggy on what numbers to put in where. There are 4 boxes across each line 2 for port triggering and 2 for port forwarding, then the option to enable it. Dont mean to sound like an idiot but abit more help would be greatly appreciated Thanks for the help btw greencross

  • Opening NAT for Modern Warfare 2 on my PC

    As I'm sure many of you are doing as well I've been playing Modern Warfare 2 since the night it came out. It is telling me that I have a strict NAT on my router (WRT160n V2). I've searched on the forum and all I can find is information on opening the NAT for the xbox 360. I run mine on my PC and I'm wondering what ports I need to open, and whatever else it would take to make Call of Duty run the absolute best possible. Thanks in advance for any help.

    i had this issue for a while. first i dmz'd through my dsl router to my desktop and everything came through fine. it wouldnt allow me to do this with my lap top though. i know that is not a good idea and it was just to check if it would open the nat at all. After some tinkering i had to call my isp and ask them to help me set up the modem so it would just pass all the info to the router. I know that the original poster of this thread has cable but i am posting something in here since it is a similar issue and it might be able to help some one. Once i set my router to PPoE and had the correct ports forwarded my nat opened on the laptop. i also turned the firewall on my router off and left upnp.
    * UDP 1500 (outbound only, no forward needed)
    * UDP 3005 (outbound only, no forward needed)
    * UDP 3101 (outbound only, no forward needed)
    * UDP 28960
    I have dsl and a wrt160 

  • Opening NAT for Xbox 360

    Hey all,
    I live in a fraternity house, and we just got an Apple Airport Extreme (802.11a), but we are having trouble playing together on Xbox Live, specifically Call of Duty: Black Ops. I've tried following many manuals across the internet but I can't seem to get my NAT to "Open." I followed Tesserax's manual that he posted for someone a while back, but I ended up only making go from "Moderate" to "Strict." I'm using a wireless adapter for my xbox as well. If anyone can help me out it would be greatly appreciated.
    Thanks!

    1) It's not the only router directly connected, we have 2 others in use as well.
    It will be critical to understand the current network configuration with both the AEBSn and these other routers. XBox Live relies on certain ports opened for on-line gaming. It also uses UPnP to do this automatically. Unfortunately, the Apple routers do not support UPnP. Instead they have a similar technology called NAT-PMP, but I don't believe this is recognized by the XBox.
    The key is that the router, which has NAT enabled and typically is the one connected directly to the Internet service, is the one that either supports UPnP or must be configured for Port Mapping/Port Forwarding or a DMZ to allow the XBox to have an Open NAT status.
    If your AEBSn is downstream of another router, then the AEBSn should be reconfigured as a bridge. This would disable its NAT service and the mapping or DMZ configuration would need to be done on that upstream router.
    2) I tried Port Mapping, not DMZ cause I was unsure how to do the DMZ part.
    With a DMZ, you are basically disabling the NAT firewall for a single device on your local network. In this case that would be the XBox. Apple calls a DMZ, the Default Host. Again, this would only be potentially helpful if the AEBSn was directly connected to the Internet source.

  • Opening NAT for Xbox 360 (HELP!)

    Ok, I really need help. I am trying to open my NAT for my Xbox 360. I recently contacted Xbox Support and they gave Port numbers and told me to contact linksys to help set the numbers up on my router. When I called them, a man told me that my that my router 's warranty is done and it would cost me 30 dollars for him to tell me how to do this. Please, someone help me fix this without giving Linksys 30 dollars. I have the Port Numbers, all I need to know is how to put those numbers on my router. Please someone help!

    Xbox Settings :-
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...
    Leave Username blank & in Password use admin in lower case...
    Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
    1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
    2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
    3) Click on set-up and change the MTU Size to 1452 and click Save Settings...Click on the Status tab and take note of DNS1 and DNS2 Addresses...
    4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
    IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
    5) Also assign the DNS Addresses on the Xbox
    Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
    6) Turn off your modem, router, and Xbox...Wait for a minute...
    7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
    IP Address: 192.168.X.[last part of ip in your device]    e.g. if static ip given to the device was 192.168.X.10 get the last part and put that to the empty box.

  • WRT54G V6 - XBOX 360 Moderate NAT - NEED Open NAT

    Ok, I have seen a post in response to wanting Open NAT on the WRT54G V6 wireless router. The response was as follows: ******************** 192.168.1.1 (default IP address). Leave the username field blank and in the password type “admin” (if you have not changed the password). When the linksys configuration page loads up fully …..click on the tab that says Application and Gaming. When the page loads up fully u can specify the ports that needs to be forwarded for your Xbox. Make sure that before forwarding the ports u assign a static IP address for your Xbox in the same range as that of your router. Specify the sane IP address in the port forwarding page. Also set the MTU of the router to 1365. Try forwarding the ports 88 and 3374. ******************* HOWEVER... I have multiple XBOX's behind the router so I don't believe doing port forwarding will be of any help here will it???? Is there a newer Linksys Wireless router that will allow us to configure Open NAT??? Is there a third part firware that can update the WRT54G V6 so that it can utilize Open NAT??? Desparately need to get 3 or 4 XBOX 360's working behind this thing in open NAT mode. Thanks in advance!!!

    well..in this case , you should go to "Applications and Gaming" and instead of "Port Forwarding" .. you should try "Port Trigerring" .. enter the required numbers .. no need to assign a static ip add to any of the x-boxes ..

  • Open NAT type on PS3 from moderate?

    Hey,
    Ive been wanting to get an open NAT type for a while, ive been unable to would anyone be able to help me?,
    i have a BT Infinity Hub 3, im currently on Moderate NAT type
    Many Thanks,
                         Sean

    Hi Matt,
    Welcome to the forum and thanks for posting. Take a look here for some information on port forwarding. I've also found this whcih you might find useful. Let me know if it helps.
    Cheers
    David
    BTCare Community Mod
    If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
    We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

  • 2 PS3's connection problems/ How do I get open Nat on 2 PS3s.

    I am having problems with the connection on my ps3's. Me and my brother both have seperate ps3's. We play call of duty mw3 together. When we are both online and playing we have problems. We both are in the same party and we try to join games but we can never join any. When we are both online, One of the ps3's has an Open NAT and the other ps3 has a moderate NAT or a strict NAT. When only one of us is playing everything is fine.
    I want to know how can I make both of them have Open NATs and how can I fix this problem I have. I have an extra router as well. Any help would be great. Thanks!

    Do This first, 
    How to setup the MI424WR Verizon FiOS Router for multiplayer gaming with the Wii and Xbox gaming con...
    And then Do one of the two below.  
    How to enable BASIC Port Forwarding on the MI424WR Verizon FiOS Router
    How to Configure Advanced Port Forwarding on the MI424WR Verizon FiOS Router
    Keep in mind that your username should be admin and your password should be the serial number on the service sticker of your router.  That is located under the bar code, and it IS case sensitive.  

  • Need open source for SUN's JIT...

    Hi,
    From where we can download the open source for SUNWJIT? Is it not available as part of Standard CDC Personal Profile package download from SUN website? Is it bundled or combined with other packages? I am unable to search in Sun website itself about JIT. Can somebody help me in this regard please?
    Thanks,
    -Suresh

    http://java.sun.com/j2se/1.5.0/docs/api/java/net/ServerSocket.html
    http://java.sun.com/j2se/1.5.0/docs/api/java/net/Socket.html

  • Need Help Opening Nat for Xbox 360

    I've searched these threads and found some solutions but it looks like my router's homepage has been updated and I cannot find some of the options needed. Anyone have an updated soultion for opening an xbox nat to open?
    Thanks!

    What is the brand and model of this router?
    If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

  • Need to open NAT for Xbox 360 using AirPort Extreme 2012 Model

    Alright this is driving me crazy haha.
    Here is the equipment im working with.
    Xbox 360
    Motoroloa SB6141 Modem from time warner cable
    Airport extreme 2012 model
    Early 2011 Macbook pro
    if its been released i have the update for it. haha
    So i have not had this issue before i got the SB6141 on Saturday.
    I have read things about it and none of it is clicking. trying to get more personalized help here.
    Any Help is appreciated.
    Thank you in advance!

    So i have not had this issue before i got the SB6141 on Saturday.
    That.....is the problem.
    Right now, you are getting Double NAT because the modem is providing NAT firewall and the AirPort is providing NAT firewall. That equals Double NAT also known as Strict NAT.
    Contact Time Warner support to get the default IP address for the modem so that you can get into the settings and turn off the firewall in the modem.  It needs to be set to pure bridge mode. A decent phone tech will know how to do this.
    If you have other modem options, you won't have this problem with a Netgear CMD31T....also on the list of TWC recommended modems.

Maybe you are looking for