WRT54GC does not associate with another AP
I need to extend my WLAN and I am trying to add an AP to the WRT54GC.
The AP is of another brand (Atlantis A02-AP-W54), it works for sure (when associated to a router of its brand).
Settings are ok (same channel, ssid, wep), so what could this incompatibility be due to?
Any workaround? It seems so weird...to me...
How you have configured this Atlantis A02-AP-W54 ( Repeater / Bridge) mode. To make this A02 to work wirelessly you need to set this A02 in Bridge or Repeater mode, then only it will work wirelessly.
Similar Messages
-
HT1849 when I download album works from itunes it does not associate with the correct artist
when I download album works from itunes it does not associate with the correct artist
Where are you looking to download them from ? You might be able to redownload them via the Purchased link under Quicklinks on the right-hand side of the iTunes store homepage on your Mac's iTunes. If that album shows there but doesn't have the cloud symbol against it for redownloading then that implies that it's still in your iTunes library
-
AP does not associate with WLC
the wlc send the log:
Feb 11 10:31:48.263 spam_lrad.c:1048 LWAPP-3-DISC_INTF_ERR1: Ignoring discovery request received on non-management interface (2) in L3 LWAPP mode
Any Idea? I review the network configuration and all is fine, I have 3 AP associate without problems but Im trying to add two more and send this log, from the same swithc.The AP 1242 in this port is working fine:
interface FastEthernet3/7
switchport access vlan 105
switchport mode access
spanning-tree portfast
The AP 1242 in this port does not associate:
interface FastEthernet3/8
switchport access vlan 105
switchport mode access
spanning-tree portfast
The APs are the same and the configuration is the same but one works fine and the other dont.
any Idea? -
AD Server does not Sync with another AD
My problem is as title, previously my server encounter DNS issues, but after delete all the event log and restart the event log is tested good. But some how now the AD do not sync.
Here is the DCDIAG
C:\Users\sysop>dcdiag
Directory Server Diagnosis
Performing initial setup:
Trying to find home server...
Home Server = Server-DC01
* Identified AD Forest.
Done gathering initial info.
Doing initial required tests
Testing server: Default-First-Site-Name\Server-DC01
Starting test: Connectivity
......................... Server-DC01 passed test Connectivity
Doing primary tests
Testing server: Default-First-Site-Name\Server-DC01
Starting test: Advertising
......................... Server-DC01 passed test Advertising
Starting test: FrsEvent
There are warning or error events within the last 24 hours after the
SYSVOL has been shared. Failing SYSVOL replication problems may cause
Group Policy problems.
......................... Server-DC01 passed test FrsEvent
Starting test: DFSREvent
......................... Server-DC01 passed test DFSREvent
Starting test: SysVolCheck
......................... Server-DC01 passed test SysVolCheck
Starting test: KccEvent
......................... Server-DC01 passed test KccEvent
Starting test: KnowsOfRoleHolders
......................... Server-DC01 passed test KnowsOfRoleHolders
Starting test: MachineAccount
......................... Server-DC01 passed test MachineAccount
Starting test: NCSecDesc
......................... Server-DC01 passed test NCSecDesc
Starting test: NetLogons
[Server-DC01] User credentials does not have permission to perform this
operation.
The account used for this test must have network logon privileges
for this machine's domain.
......................... Server-DC01 failed test NetLogons
Starting test: ObjectsReplicated
......................... Server-DC01 passed test ObjectsReplicated
Starting test: Replications
[Replications Check,Replications Check] Inbound replication is
disabled.
To correct, run "repadmin /options Server-DC01 -DISABLE_INBOUND_REPL"
[Replications Check,Server-DC01] Outbound replication is disabled.
To correct, run "repadmin /options Server-DC01 -DISABLE_OUTBOUND_REPL"
......................... Server-DC01 failed test Replications
Starting test: RidManager
......................... Server-DC01 passed test RidManager
Starting test: Services
Could not open NTDS Service on Server-DC01, error 0x5 "Win32 Error 5"
......................... Server-DC01 failed test Services
Starting test: SystemLog
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:28:32
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:40
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:41
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:41
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:42
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:44
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:45
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:47
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:48
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:49
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:50
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:51
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:51
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:52
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:53
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:54
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:55
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:56
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:28:57
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:29:33
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:31:00
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:31:11
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:19
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:20
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:21
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:22
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:23
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:26
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x00000457
Time Generated: 09/05/2014 13:31:27
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:46:02
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:48:14
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:53:15
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x40000004
Time Generated: 09/05/2014 13:53:15
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:53:17
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 13:53:26
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:01:03
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:11:51
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:12:52
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:13:25
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:14:10
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:15:10
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:16:05
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
An Error Event occurred. EventID: 0x80000003
Time Generated: 09/05/2014 14:17:57
EvtFormatMessage failed, error 15100 Win32 Error 15100.
(Event String (event log = System) could not be retrieved, error
0x3afc)
......................... Server-DC01 failed test SystemLog
Starting test: VerifyReferences
......................... Server-DC01 passed test VerifyReferences
Running partition tests on : ForestDnsZones
Starting test: CheckSDRefDom
......................... ForestDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... ForestDnsZones passed test
CrossRefValidation
Running partition tests on : DomainDnsZones
Starting test: CheckSDRefDom
......................... DomainDnsZones passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... DomainDnsZones passed test
CrossRefValidation
Running partition tests on : Schema
Starting test: CheckSDRefDom
......................... Schema passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Schema passed test CrossRefValidation
Running partition tests on : Configuration
Starting test: CheckSDRefDom
......................... Configuration passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... Configuration passed test CrossRefValidation
Running partition tests on : dunhambush
Starting test: CheckSDRefDom
......................... dunhambush passed test CheckSDRefDom
Starting test: CrossRefValidation
......................... dunhambush passed test CrossRefValidation
Running enterprise tests on : dunhambush.dunham-bush.com
Starting test: LocatorCheck
......................... dunhambush.dunham-bush.com passed test
LocatorCheck
Starting test: Intersite
......................... dunhambush.dunham-bush.com passed test
Intersite
Here is the IPCONFIG
C:\Users\sysop>ipconfig
Windows IP Configuration
Ethernet adapter Local Area Connection 7:
Connection-specific DNS Suffix . :
IPv4 Address. . . . . . . . . . . : 172.16.252.1
Subnet Mask . . . . . . . . . . . : 255.255.252.0
Default Gateway . . . . . . . . . : 172.16.252.254
Ethernet adapter Local Area Connection 1:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 8:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 9:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Tunnel adapter Local Area Connection* 13:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :Hi All,
Yes, this issues server is recover by using image. "DSA not writable" value in regedit is 4. It is only way to resolve this issues by using USN
rollback?
After doing the demote of the DC will the policy will erase too?
Another question, after demote the DC, what i need to do is create a new global catalog. Will the policy will copy from another server?
Thank.
Recovered by using an image? Unfortunately, that's not supported with anyting other than a Hypervisor (HyperV, VMware, Infoblox, etc), and an operating system (Windows 2012 or newer), that supports the VM-GenerationID attribute. Otherwise, for versions that
don't support it, once a DC is in a rollback state, forget it.
As I've suggested, and as Meinolf also suggested, just run dcpromo /forceremoval and clean up the database, rebuild the DC from scratch (you can use a SYSPREPPED image if you like), and re-promote it. It's quicker, less of a hassle and no headaches.
As for DHCP on it, you can export the database if you like, and re-import it after you re-promote it.
Move a DHCP Database to Another Server
http://technet.microsoft.com/en-us/library/dd183705(WS.10).aspx
For future reference, please use supported AD backup methods.
Ace Fekay
MVP, MCT, MCSE 2012, MCITP EA & MCTS Windows 2008/R2, Exchange 2013, 2010 EA & 2007, MCSE & MCSA 2003/2000, MCSA Messaging 2003
Microsoft Certified Trainer
Microsoft MVP - Directory Services
Complete List of Technical Blogs: http://www.delawarecountycomputerconsulting.com/technicalblogs.php
This posting is provided AS-IS with no warranties or guarantees and confers no rights. -
Photoshop cc does not associate with psd files?
I have a simple answer to the problem of photoshop cc not being able to associate psd files and not showing in the options window when you try to associate it with the psd file? How do I get it into the forum where it belongs?
Photoshop does associate with PSD and PSB files on both platforms.
It sounds like your OS is confused about the available file associations.
Which OS version are you using? -
Address Book Associates Field does not sync with iPhone
Apple went to the trouble of getting custom field names in the Mac OS Address Book to synchronize with the iPhone (which is wonderful), but they left one field 'unsyncable'; the associates field. If you list a contact's manager name, spouse name, child name, etc. in Address Book, it does not sync with the iPhone (OS 3.0.1) 'Phone' application. This is very useful (and embarrasment-preventing) when needing to remember the name of a contact's manager, wife, child, etc. Does anyone have any idea why Apple left this out of the sync? Certainly it couldn't have to do with saving memory...
Oh yes! i have this same problem - i have tried emailing Apple Customer Support but they were unable to help me. They advised me to speak to technical or raise the issue on the Apple Support board (but someone already has!)
so if someone can help us both out here with how to sync additional field information added on Address Book on Mac to then sync all this additional information to iPhone, we would be greatly appreciative!!Thanks,
Mark -
Home sharing does not work with new mountain lion update.
home sharing does not work with new mountain lion update. Does anyone else have the same issue. Updated all computers in my home, deauthorized and reauthorized each computer. turn off home sharing and turned it back on. don't know what else to do..please help...
Our Apple TVs continue to lose connection ever since installing Mountain Lion on the host computer. The only thing that fixes them is to quit and relaunch iTunes, which only works unti the ATV goes to sleep. If a movie is paused for more than a few minutes and the ATV goes to sleep, pressing play again on the remote is greeted with "There are no movies on this computer" or "Turn on Home Sharing."
If we stop a video on one ATV and attempt to resume it in another room, the error begins again. The other ATV can't connect until iTunes is relaunched.
My guess is that it has something to do with the new [annoying] security settings. But I still haven't found a fix other than restarting iTunes everytime we want to watch something from our downloads. Fail. -
External USB HD does not work with HAL:
External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era -
Using Firefox browser I can convert to the newest version of Yahoo mail and for this conversion it works satisfactorily. If I close Yahoo mail , either going to another site or closing the Browser, next time I open Yahoo mail it has reverted to old version (occasionally this does not happen but 80% of time it reverts). This does not happen with Explorer or Chrome. I have ensured updated Firefox. Tried Yahoo Ask for answer but no luck.I like Firefox Browser.
hi ghrobert39, it is an issue with the new yahoo layout,see :
http://answers.yahoo.com/question/index;_ylt=Ah_K4HUp4sat2HACnDjjfLniDn1G;_ylv=3?qid=20121213000810AAUYfSE
http://answers.yahoo.com/question/index;_ylt=AkaQjlpKRxhYzrk5rgeMkvviDn1G;_ylv=3?qid=20121212164112AASaQcC
[http://help.yahoo.com/kb/index?locale=en_US&y=PROD_ACCT&page=content&id=SLN8821 Overview of the new Yahoo! Mail design]
i hope this is the answer : http://answers.yahoo.com/question/index;_ylt=AjpJXHmHQWc_qTtD86_2imfiDn1G;_ylv=3?qid=20121213051550AAsOJ6g
thank you -
Adobe Flash Player does not work with Safari. What can I do?
Hi,
I have a MacBook Pro, Retina, 15 inch, late 2013, 2 GHz Intel Core i7, using OS X 10.9.4. I have installed Adobe Flash Player. In my System Preference, in the advanced settings, it is set to install updates also tells me that I have the NPAPI Plug-in (version 14.0.0.145) installed but not the PPAPI Plug-in. Is this the reason why it does not work with Safari (keeps telling me to download the app, which I did but still does not work)? Is there any way I could fix the problem? Please, help.
Thanks.If you can't install or update Flash, follow these instructions.
If you have installed the latest version of Flash, please take each of the following steps that you haven't already tried. After each step, relaunch Safari and test. For a "missing plug-in" error, start with Step 8. Back up all data before making any changes.
Step 1
You might have to log out or restart the computer before a Flash update takes effect.
Step 2
From the Safari menu bar, select
Safari ▹ Preferences... ▹ Privacy ▹ Remove All Website Data...
and confirm. Close the window. Then select
▹ System Preferences… ▹ Flash Player ▹ Advanced
and click Delete All. Close the preference pane.
Step 3
If you're only having trouble with YouTube videos, log in to YouTube and load this page. You may see a link with the text "Leave the HTML5 Trial." If so, click that link.
Step 4
a. If you get a warning of a "blocked" or "outdated" plug-in, then select the Security tab in the Safari preferences window. In the list of plugins on the left, there should be one—and only one—entry for "Adobe Flash Player," showing the same version number that you installed. Select that entry. On the right there will be a list of websites for which you have specifically allowed Flash, if any. It's normal for the list to be empty. Below that is a menu labeled
When visiting other websites
From that menu, select either Allow or Ask.
b. If you still get the alerts, then go back to the Flash Player preference pane and select the Advanced tab. Click Check Now. Quit and relaunch the browser.
c. If the alerts still persist, triple-click anywhere in the line below on this page to select it:
/System/Library/CoreServices/CoreTypes.bundle/Contents/Resources
Right-click or control-click the highlighted text and select
Services ▹ Open
from the contextual menu.* A folder should open. Inside it, there should be a file named "XProtect.meta.plist". If that file is missing and you know why it's missing, restore it from a backup or copy it from another Mac running the same version of OS X. Otherwise, reinstall OS X.
*If you don't see the contextual menu item, copy the selected text to the Clipboard by pressing the key combination command-C. In the Finder, select
Go ▹ Go to Folder...
from the menu bar and paste into the box that opens by pressing command-V. You won't see what you pasted because a line break is included. Press return.
Step 5
In the Safari preferences window, select the Advanced tab and uncheck the box marked
Stop plug-ins to save power
Step 6
Open this folder as in Step 4:
/Library/Internet Plug-Ins
Delete the following item, or anything with a similar name, if present:
Flash Player (failing).plugin
You may be prompted for your login password.
Step 7
Re-download and reinstall Flash. Download it from the domain "get.adobe.com". Don't click a link from any other website, including this one, because you can't trust links. They may be an attempt to trick you into installing malware masquerading as Flash. Type the address into the browser window. Never download a Flash update from anywhere else.
Step 8
If you get a "missing plug-in" error, select
Safari ▹ Preferences... ▹ Security
from the Safari menu bar and check the box marked
Allow (or Enable) plug-ins
Then click the button marked
Manage Website Settings...
if present and make sure that the website is not blocked for Flash.
Step 9
Select
Safari ▹ Preferences... ▹ Extensions
from the Safari menu bar. If any extensions are installed, disable them. -
After downloading iTunes 11, my calendar on my iMac (OS X 10.6.8) does not sync with iCal on my iPad 2. Why is this?
Ok, here's what seems to have worked....but will need to monitor to see if this stays "stable".
1) As suggested by King_Penguin in another Discussion thread [apple support > iPad > Using iPad > Discussions] (https://discussions.apple.com/message/15911962#15911962), I turned off iPhoto startup on the iPhone. Then ejected iPhone from USB.
2) Reconnected iPhone via USB. iTunes did not start up. Started up iTunes manually. Went to Summary page for iPhone, unchecked the "open iTunes" option, selected APPLY button. Let iTunes run its application process.
3) Then checked the "open iTunes" option. Selected APPLY button. Got a dialog box asking if I wanted "iTunes Helper" to be installed; selected YES. Let iTunes run its application process. Ejected iPhone. Closed out iTunes. Reconnected iPhone via USB. AND iTunes STARTED UP AUTOMATICALLY (yay!). Let iTunes do some backup and sync'ing. Ejected iPhone. Closed out iTunes.
4) Connected iPad via USB (on computer). AND iTunes STARTED UP AUTOMATICALLY (yay!).
I don't know for sure that the iPhoto "automatic launch" was causing the interference, but it seems like the "uncheck/check" the "open iTunes" option seemed to re-set the problem that I encountered. I don't want to say for sure that this issue is fixed, but it appears to be under control for the moment.
Thanks to everyone for your thoughts and assistance. Maybe this info will help someone else out now that it's in the forums/discussions. -
Window 10 build 10041 does not work with Intel 82579V Gigabit Ethernet on ASUS motherboard
I originally posted this question here:
answers.microsoft.com/en-us/insider/forum/insider_wintp-insider_update/window-10-build-10041-does-not-work-with-intel/6729892f-83aa-4822-b20a-ea84f4fd06c7
and was asked to post it on this forum...
I updated a computer I have which is a quad core i7 that I built and includes an ASUS motherboard with Intel 82579V Gigabit Ethernet built in. Windows 10 preview 9926 worked fine with this network adapter. Window 10 build 10041 does not, and I have tried
it twice so far. I even went as far as buying a Thunderbolt-Gigabit Ethernet Adapter (Broadcom, sold by Apple)... and while it installed the driver automatically, it did not work either. Each time you try to view the properties of either of them, it locks
up or give an error. In fact, doing much of anything with the Intel adapter icon assures you of not being able to do a clean reboot... have to kill power. I have finally gone back the previous version 9926, which has its issues but no where near as bad
as not having any network connectivity! Does anyone have this issue and a workaround?
Note, there are two images on the windows 10 preview forum that I posted this question on. I could not post the full link as I was getting a message here that links and graphics are not allowed.Thanks Roger, I posted the following yesterday in the other thread (thinking it was this thread - confusing after they moved it here)... It may be that the new driver fixes the issue that 10041 has with it, but I have not tried that yet. If I do I will update
this... Thanks!
I have more information about this, which basically exonerates any issue with the Intel 82579V Gigabit Ethernet hardware or software. I have 3 computers with Windows 10 preview so I have multiple angles to see issues from. With this I have found a culprit
(but I suspect not just the only culprit) in this above mentioned problem...
10041 build combined with installing (or attempting to install) CISCO VPN Windows 7 64bit 5.0.07.0440-k9 client causes the issue mentioned above. I confirmed this on a completely different machine with a totally different Ethernet adapter. First machine
is an ASUS motherboard in a tower system I built, with the Intel 82579V Gigabit Ethernet hardware built in. Second machine is a Gateway Laptop from 2008 which has a Marvell Yukon 88E8057 PCI-E Gigabit adapter built in. Build 10041 will work fine with my 2008
laptop, including the MS VPN client (which I have tested). However, if you attempt to install or even uninstall the Cisco client you will have to do a recovery to a restore point (as I have done twice) in order to get your network working again. Installing
or attempting to install (because it never even does install properly and times out), CISCO VPN client will render your entire network unusable. Going back to a restore point saved me and I am still running 10041 but I can't use CISCO VPN client any longer.
I could with build 9926, including on all 3 machines. I now have 9926 on two machines and 10041 on only the 2008 laptop.
Hopefully this above information helps someone resolve the issue. I will also mention, even though my network is working on the 2008 laptop, I still can't go into the Control Panel\Network and Internet\Network Connections and right mouse click on the Marvell
Yukon 88E8057 PCI-E Gigabit adapter icon. I get an error when clicking on Properties menu popup : "An unexpected error has occurred". So something is still up with my network adapter driver or windows software, but it could be a side effect of all
that has happened with the Cisco software install attempts under 10041.
Another note: CISCO Anyconnect also has the issue. -
When I click on a .docx document Firefox thinks it is binary and saves it but does not open with MS Word. But it knows .doc is MS Word and opens it automatically (this is the behavior I would like with .docx docs.) In preferences -- applications - it is just says "content type" is "microsoft word document" but doesn't give a way to choose .docx specifically. Is there another way to do this?
Iam running Mac OS X 10.6.4 and Firefox 3.6.8 with MS Word Mac 2008Hi ,
According to your description, my understanding is that you could not edit documents with Office client application in SharePoint 2010.
Let’s do a troubleshooting about this issue:
1. Make sure that you have installed Office application on your machine.
2. Which explorer did you use for your SharePoint. Please test it with IE 10 32-bit, compare the result.
3. Please try to reset IE, compare the result.
4. Add your SharePoint site into Trusted site on your IE options.
5. Make sure all add-ons related to SharePoint are enable, special for SharePoint OpenDocument Class and SharePointOpenXMLDocuments.
6. Since you used OWA for your SharePoint site, please try to disable OWA, then open documents with client application, compare the result.
I hope this helps.
Thanks,
Wendy
Wendy Li
TechNet Community Support -
Error: File does not begin with '
After changing two javascript "else if" statements to "if" in an Adobe LiveCycle v8 form, I received errors upon saving. Now the file seems to be corrupt because when I attempt to open it I get an error stating "File does not begin with '". Does anyone know what could be causing this AND MORE IMPORTANTLY if there is a way to salvage my form? Please help!
Hi VetSrini,
Thanks for the update. I was able to figure out what was wrong.
Now there is another problem. When i try "View Output", the excel file is shown and the following options are also shown:
1. As an XML List
2. As a read-only workbook
3. Use the XML Source Task Pane
When I try the first option, I get the following error:
An Invalid Character was found in text content
When I try the third option, I get the following error:
Cannot load the specified XML or schema source.
when i press the details button, it gives me the following detailed error:
An Invalid Character was found in text content
When I try the second option, i get the same error, but with some xml tags
Can anyone please help me and tell me why i am getting these errors.
Thanks in Advance,
Arun -
SCCM issue - "LANG_LIST has some locales which does not match with the locale of serial number"
I have a problem with the error "LANG_LIST has some locales which does not match with the locale of serial number" recurring.
I am trying to install Acrobat XI Std silently by SCCM.
I've used the Adobe Customisation Wizard to create a mst which include the volume serial number we have with our licence purchases. Note that I am in Australia. I use the command line in SCCM for the install as "msiexec /i "AcroStan.msi" TRANSFORMS="D&B_AcroStd.mst" /qn" which fails silently. If I install on a local machine using an admin command prompt and changing to /qb at the end, I get the aforementioned error.
I have a few things to try and resolve, having searched the adobe forums and other forums for the solution. The mst is only trying to install US English & I have even gone so far as to use the direct editor in the customisation wizard and change some values in the property table to resolve this. In the property table I can confirm that LANG_SEL_DEFAULT = ENU, REGIONAL_LIST = ENU, LANG_LIST = en_US, ProductLanguage = 1033
Is there a way to check the language specified for ym serial number?
BryndonUpdate on a couple of details:
@Sabian,
Thanks for the location, I've downloaded and then when I tried an install of the newly extracted msi (admittedly on the same computer) I got exactly the same issue. Of note though is that running /qf automatically brought up the same serial number and the same incorrectly spelled company name. Installing on another computer (freshly imaged) doesn't have those inputs already present under /qf. Next when I try using the transfrom (a new one) with /qr it gives an error of the serial number, displaying the entire serial.
@Sebastian
I've had a look through yours and it seems our issues could have the same origin. Looks like I may have to call customer support regarding the serial number as Sabian suggested in your thread.
The bit that gets me is when the same serial number is used in a manual install (or /qf) then it installs ok without any errors.
Maybe you are looking for
-
Dear All, Please help me in one scenario. My client want PO print before release. He want to take print of po before release so that he can bargain with vendor & make changes accordinglly before release. Actually he doesn't want to release the po aga
-
Billing in Third Party Scenario
Hello All, How does the billing occurs in the third party scenario ? Regards
-
How to reset your user name on apple support communities?
If your dont remember your user name in the Apple Support Communities, how can you reset it?
-
C3180 Photosmart All-in-one won't print. Gives message 'clear paper jam.' There is no paper jam.
C3180 Photosmart All-in-one won't print. Gives message 'clear paper jam.' There is no paper jam. About a month ago there was a paper jam, but was removed. It worked fine since then until yesterday. I've tried all the HP trouble-shooting suggest
-
No matter what I do I cant get air drop to work
I have everything on my new (2014 Aug )Mac book pro OX Yosemite 10.10.1 iPhone 5S V 8.1.2, working exactly as outlined on many forums. I mean its perfect both systems, its all ON and dialed. Worse Airdrop was working and I NEED it bad now, but no mat