WRT54GC How to make more port range forwarding fields?

Hello I only have 15 port forwarding fields to enter all my programs and it is not enough since I have two pcs accessing the router getting two different ips for each one. Each aplicattion needs two forwards one for 192.168.1.100 the other for 192.168.1.101. How can I add more fields? thanks a lot

hi , this is a product limitation that you cannot add more than 15 entries.....what you can try though , is to "trigger" the ports instead of forwarding them....triggering does not require you to specify an IP address....the port will open for whichever PC makes the request from within the network...

Similar Messages

  • WRT54GC resetting Port Range Forwarding

    I have a WRT54GC, with firmware v1.05.7.  And I have recently modified the Port Range Forwarding.  It will work OK for a day or two, then for no reason it stops working.  When I check the configuration, I see it has reverted to the old Port Range Forwarding config.  So I change it again, save it, and again it will work for a day or two before reverting to the old config.  How can this be happening?

    Hey try resetting the router reset button in such a way that power light is blinking on the router & then do a complete network power cycle i.e., unplug the power cables from the modem & from the router & then plug in the power cable to the modem first once all the lights are solid green you could plug in the power cable to the router & check out it will definately work!!

  • DMZ v. Port Range Forwarding????

    Ok,  DMZ opens all ports. But I was wondering if port range forwarding might be better. Once again I am still trying to eliminate lag with my 360. I enabled the port forwarding for the ports specified by the 360. I also blew all ports wide open with DMZ. Is it better to just port forward without DMZ? I don't care about the security issues. I just want speed. I already disabled all firewall features of the router. My PC is locked up tight and I'm not worried about it. The ports I forwarded are 88 TCP and 3074 Both. Is there something I'm missing here? I'm running a 5 meg connection. It's faster than my old DSL connection. I even found a website that told me to change my IP manually on 360 which I have done and it worked to open my NAT. Any gamers please help. Again I'm not trying to do anything to my PC. That connection is fine. Just need to tweak more upload with less lag to 360.

    ok.......How do I use them? Triggered Range start port? to end port? Forwarded Range start point? to end point? Would it be the same forwarded ports? do I put the same port # in all for areas? I'm working with WRT54GS ver. 6

  • DPC3825 Port Range Forwarding page disappeared

    I've been using the DPC3825 gateway to forward port to my server. It's not long ago that I realised the page for port forwarding had disappeared. I'm confused and now I can't configure the port forwarding any more. Please can anyone tell me what caused this and how to get it back? Many thanks in advance. 

    to re-iterate again ..
    recent changes made to 'Single Port Forwarding' work .. but changes (as well as existing) on 'Port Range Forwarding' just dont forward.
    to re-iterate again ..
    stuff (whether existing or newly added) works for 'Single Port Forwarding' .. but stuff (whether existing or newly added) does NOT work for 'Port Range Forwarding'.
    This any more clear?
    Thx

  • WRT54GL Port Range Forwarding?

    Hi. In Port Range Forwarding there are only 10 lines (konfigurating 10 diff. ports). What if you need to forward more ports than 10?
    Solved!
    Go to Solution.

    Install 3rd party firmware like dd-wrt or tomato.
    Of course, you shouldn't need so many forwardings to begin with.

  • WRT54G2 More ports to forward

    So.. Like the titles says:
    How can I enable more ports to forward?
    I just want to port forward more applications to my PC.
    (my router is a WRT54G2)
    4)G2WRT54G2
    Kind Regards,
    WhiteSnoop
    --------signature---------
    Learn from the master
    Walk with the master
    Become the master
    Solved!
    Go to Solution.

    Ok, thanks for the reply
    but you know why they won't let me more, is there an explanation ?
    --------signature---------
    Learn from the master
    Walk with the master
    Become the master

  • The router forgets Port Range Forward settings

    Hello, after a year or so of working absolutely flawlessly, the router, all of a sudden, started forgetting the Port Range Forward settings.  In particular, I have port 80 set to go to a specific IP address.  Every now and then, it will start going to a different address within the network (even though the Port Range Forward page still shows it pointing to the right IP address).  
    I disable Port Forwarding for that port, then re-enable it and everything is fine.  For about day or two and then the problem re-appears.
    What could be the issue?
    Thanks.

    What is the model no of the Router...?
    Who is your ISP...?
    What firmware you are using on the router...?
    Try to reset the router and re-configure it from scratch.Now,check if that make any difference.

  • Port Range Forwarding on E1000

    Ports selected to forward in the the 'Port Range Forwarding' page do not forward.    They do however forward properly from the 'Single Port Forwarding' page.
    Help?
    TIA

    to re-iterate again ..
    recent changes made to 'Single Port Forwarding' work .. but changes (as well as existing) on 'Port Range Forwarding' just dont forward.
    to re-iterate again ..
    stuff (whether existing or newly added) works for 'Single Port Forwarding' .. but stuff (whether existing or newly added) does NOT work for 'Port Range Forwarding'.
    This any more clear?
    Thx

  • What's safer: Port range forwarding or Upap?

    Hello there,
    I recently replaced my router and since then have been unable to get video and audio chats to work. I get the "XXXXX did not respond" message. Text chat is fine. By what I have read in this forum, my problem has to do with port settings on my new router, a Linksys wrt54gx2.
    My question is this; is it safer/more secure to use port range forwarding or the universal plug and play option? Do I need both?
    The Mac OS X firewall settings are currently off.
    Thanks in advance for any advice.
    John

    HI John,
    This is not a suitable device for iChat for some reason.
    This page is for the WRT54GX (not the GX2)
    This shows the Port Forwarding for this device (and the default IP and User ID and Password).
    You should not use Port Forwarding and UPnP together.
    The UPnP setting in in the Admistration tab.
    Port Forwarding uses NAT (Network Adress Translation) and this can cause problems between some devices.
    UPnP does Broadcast that is available but is normally limited to a few Hops.
    In most device this can be limited to just one hop if you require.
    1:27 PM Monday; May 29, 2006

  • WRT160n Port Range forwarding problem

    I have a WRT160n that I am trying to forward some ports on for some DVR equipment. When I use the single port forwarding and enter each port separately it works fine. But I have 2 DVR's and they use a bunch of ports each so I want to use the port range forwarding because there are not enough spots in the single port forwarding section. The ports I am trying to forward are 8000-8004 for one IP address and 8005-8009 for a second IP address. I have entered it into the port range forwarding section but I can not connect from outside my network. As I said if I enter them in the single port section seperately as 8000,8001,8002,8003,8004 then I can connect fine outside my network. Any idea's what the problem is?

    chuckb223 wrote:
    jaymay wrote:
    How about you isolate it first by forwarding the ports for one DVR. Forward them one by one on the Port Forwarding Range page then see if it works on one DVR. If it will, try to do the same thing for the other DVR.
    Yes I already tried this with no luck. I tried just opening one port in the port forwarding for 1 DVR and it did not work, Opening this same port in the single port forwarding did work.
    Is your router a version 1,2, or 3? Your router probably needs to be updated (firmware).
    Firmware
    11/08/2010
    Ver.1.02.11
    Download
    3.15 MB
    Firmware
    11/15/2010
    Ver.2.0.03 Build 9
    Download
    3.25 MB
    Firmware
    07/12/2010
    Ver.3.0.03 Build 3
    Download
    3.31 MB
    And then reset and reconfigure your router again for internet connection and try the port range forward again and see if you can both DVRs working properly.

  • Port/Port Range Forward limit on Airport Extreme (N)

    Hi there,
    Can anyone please tell me if there is a limit to how many ports I can forward to separate machines in my LAN in the new Airport Exreme N?
    Currently routers like the Linksys WRT300N only provide 10 items for port forwarding and port range forwarding, respectively. Flashing a Linksys router with DD-WRT gives you an unlimited amount.
    Thanks very much!
      Mac OS X (10.4.8)  

    There is no noticeable limit. Everything I see in the manual hints that you should be able to shove as many as will fit into memory... which is a lot.
    The main reason for the limitation is that companies like Linksys, for whatever reason, do not like to mess with the complicated HTML required to support 'unlimited' port forwarding in their tool. They get around the complexity by putting enough fields on the page so that they hope their customers don't run out.
    In Apple's case, the configuration tool is a native application, rather than a web page, so it is simple to support 'unlimited' port forwarding.

  • Is WRT54G v5 'Port Range Forward' mean the same as NAT ?

    Dear all:
    As title said.
    Do I missunderstand anything?
    I would like to sent magic packet pass through WRt54G, thus I would like to set port forward.
    Could anyone help ?
    I thank you in advance.
    Best Regards
    chen min

    NAT represent network address translation as well.
    I think WRT54G supports WOL except WOW directly.
    I try to sent magic packet pass through WRT54G. And according of log information, It did passed through WRT54 on the port which I assigned.
    I think it would be possible if boardcasting IP was allowed in Port Range Forward.
    I kept looking for more information from forum.
    Best Regards
    chen min

  • How to make more than one partition on Airport Time Capsule?

    how to make more than one partition on Airport Time Capsule?

    Only for the very brave......
    Open up the Time Capsule (voids the warranty)
    Pull the hard drive
    Place the hard drive in a separate enclosure
    Connect the enclosure directly to your Mac
    Use Disk Utility to partition the hard drive
    Reinstall the hard drive back in the Time Capsule
    For the rest of us.....
    The next best thing might be to set up one or more disk images on the Time Capsule, which will allow you reserve a given amount of space for each disk image.
    Open up Macintosh HD > Applications > Utilities > Disk Utility
    Click on the New Image tab
    Navigate to the Time Capsule
    Set up the disk image by naming it and specifying how much space you want to reserve

  • How to make more albums in photo library?

    How to make more albums in photo library?

    If you do not have iOS 5, you have to use subfolders in your one photo syncing folder. You can have one level of folders in the syncing folder and each folder is an album.
    With iOS 5 you can create albums in the Photo app.

  • Unable to Save in Port Range Forwarding

    I'm using the BEFW11S4 wireless router and am unable to save the new port range forwarding settings I have entered.  Everytime I click Save Settings, I receive a box which reads:
    "The server 192.168.1.1 at Linksys BEFW11S4 V4 requires a username and password.
    Warning: This server is requesting that your username and password be sent in an insecure manner (basic authentication without a secure connection)."
    When I enter the same u/p that I used to access the router in the first place, it rejects and keeps bringing up the log in screen.
    I cannot get the port range forwarding to save at all due to this.
    Does anyone have any suggestions?
    Thank you!

    try remembering the password you used for first time while installing the router .... if not then use default password admin with out any username ....
    If still not working then you need to reset the router ....

Maybe you are looking for

  • Java.rmi.RemoteException: Error initializing ejb-module java.lang.NoClassDe

    Hi, I have an ear file which has ejb jar and war file. Application is running fine through Jdeveloper but when am trying to deploy it in Oracle Application Server 10g getting following error. Any help in this would be appreciated. Deployment failed:

  • SM20/SM20N audit report analysis - in background

    Hi, I would like to create an audit log / audit report analysis in background. I've found an article bu interested to understand if it is the only way to do that ? article: http://sap.ittoolbox.com/groups/technical-functional/sap-security/security-au

  • How to format popup info in web reports

    Hi Forum, maybe it's quite easy, but I've no idea if or how I can format the popups in web-reports, that come up if you hover a graph. The current output is e.g.: 1/4 Figure-description category value Is there a way to format the upcomming popup like

  • No password on guest network = unsecured network overall?

    Hi Just wondering if leaving the "guest network" password free creates an unsecured network overall? I just purchased an Airport Extreme to replace a D-link router [that would no longer stream airtunes (to my airport express) since I upgraded to snow

  • Firefox will load only load google?

    Firefox's homepage and google are the only sites that work while I'm connected to my wireless home network. I have other computers on my network wireless, without these problems. The weird thing is, google is able to guess what I'm typing in the sear