WRT54GC Operation Mode: Router Or Gateway

The WRT54GC has two modes: Router and Gateway. What is the difference?
I'm trying to do the following and I'm not sure what mode I need for that
/-->LAN1 (192.168.1.*)
2WireModem/Router
\-->WRT54GC-->LAN2 (192.168.2.*)
Note 1: LAN1 and LAN2 have different IP ranges.
Note 2: I tried router mode connecting the WAN port of the WRT54GC to a LAN port on the 2WireModem. The 2WireModem then complained that there is another router behind it. Why does it care?

As indicated in the graph I have changed the IP of the WRT54GC to 192.168.2.1. But what mode do I have to set it (router or gateway) to allow two separate LANs?
Also, the computers connected to the WRT54GC need to have internet access through router 1. Somebody told me I need a static IP for this. Is that correct?
Thanks

Similar Messages

Wrt300n "Operating Mode" missing

Hi i have a wrt300n v2 (firmware 2.00.17) being a bit of a pig
i seams to think that it is ppoe modem all the time, i have an adsl modem hooked in there but wont find an route to this
if there adsl modem is pluged in to the wan port (with nat switched on and on a diffrent subnet)and setup that way it works (with port farding prblems and other things up)
my help page said the should be a "Operating Mode" drop down in the
setup ---> advanced routing
page but no for me theres not any one got any ideas
davidk

I found my answer as to why it doesn't work. SSD and HDD write and read memory differently. Even booting the OS was different for Windows 7 hence the OS errors.

%OIR-SP-6-DOWNGRADE_EARL: Module 4 DFC installed is not identical to system PFC and will perform at current system operating mode

Hi Everyone,
Good day!
We have WS-SUP720-3BXL and WS-F6700-DFC3CXL installed on 7609-S router and based on this link http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/107258-C6K-PFC-DFC-CFC.html the Resultant mode should be PFC3BXL. However, as shown below, the PFC operating mode becomes PFC3B.
Router#sh platform hardware pfc mod
PFC operating mode : PFC3B
Following are the modules installed in our router.
Router#sh mod
Mod Ports Card Type                              Model              Serial No.
4    8 CEF720 8 port 10GE with DFC            WS-X6708-10GE      XXXXXXXXX
5    2 Supervisor Engine 720 (Active)         WS-SUP720-3BXL     XXXXXXXXX
6    2 Supervisor Engine 720 (Hot)            WS-SUP720-3BXL     XXXXXXXXX
Mod MAC addresses                       Hw    Fw           Sw           Status
4 001f.6ca4.2588 to 001f.6ca4.258f   2.1   12.2(18r)S1 12.2(33)SRE9 Ok
5 001f.6c77.8448 to 001f.6c77.844b   5.9   8.5(3)       12.2(33)SRE9 Ok
6 001a.a22d.b200 to 001a.a22d.b203   5.10 8.5(3)       12.2(33)SRE9 Ok
Mod Sub-Module                  Model              Serial       Hw     Status
4 Distributed Forwarding Card WS-F6700-DFC3CXL   XXXXXXXXX 1.0    Ok
5 Policy Feature Card 3       WS-F6K-PFC3BXL     XXXXXXXXX 1.11   Ok
5 MSFC3 Daughterboard         WS-SUP720          XXXXXXXXX 4.0    Ok
6 Policy Feature Card 3       WS-F6K-PFC3BXL     XXXXXXXXX 1.11   Ok
6 MSFC3 Daughterboard         WS-SUP720          XXXXXXXXX 4.1    Ok
Mod Online Diag Status
4 Pass
5 Pass
6 Pass
The problem now is that I am seeing the messages below and the maximum value that I can enter for mls cef maximum-routes is 239K only instead of 1M.
%MLSCEF-SP-4-FIB_EXCEPTION_THRESHOLD: Hardware CEF entry usage is at 95% capacity for IPv4 unicast protocol.
Based on this link, http://www.cisco.com/c/en/us/support/docs/switches/catalyst-6500-series-switches/117712-problemsolution-cat6500-00.html WS-SUP720-3BXL and WS-F6700-DFC3CXL has a Default IPv4 TCAM Space of 512K but I'm only getting the following.
Router#sh mls cef max
FIB TCAM maximum routes :
=======================
Current :-
IPv4 + MPLS         - 192k (default)
IPv6 + IP Multicast - 32k (default)
Please advise what seems the problem.
Thanks

Was the WS-X6708-10GE inserted some time after the router was last reloaded? Cisco's PFC/DFC FAQ states that mixing different types of PFCs and DFCs affects OIR (online insertion and removal) - i.e. the router needs to be reloaded with the line-card installed in order for that PFC/DFC combination to work as expected (or even to work at all) - and although I couldn't find PFC3BXL+DFC3CXL as an explicit example of such situation, a reload might be worth a shot if the downtime is not too much trouble...

How to change the 'Default operating mode' of a mapping on the repository and not from the client

Hi everybody,
I am using OWB 11.2.0.3 and under the mapping's configuration property, I have the necessity to change the Run time parameter "Default operating mode" to SET_BASED in almost all my mappings.
Because I have 745 mappings in which the Default operating mode is different from SET_BASED, instead to open 745 times the 'Configure' and update manually the value, is there a way to update safely these values (with an oracle predefined script) directly on the repository ?
I know that exists a view called CMPSTRINGPROPERTYVALUE_V based on a table called CMPSCOPrpClasses, but changing this table it's very complicated for me because contains only keys and then I don't know in which way is connected with all the other structures....
If somebody knows a method more efficient to do these updates on the repository and not from OWB client I will appreciated it!
Thanks in advance
Alessandro

Urgent... help!!! Thanks
in short, my server log says transaction access mode is "read only", so my calling home.create() always triggers a transaction rollback. How to change the access mode to "read write"?
Is possible to work out through one of the descriptor files? Or ini settings of the underlying pointbase database? Or any other way around?

Urg:"At operation mode" in background job scheduling

Hi Folks,
I am doing background job for a program. Pls tell me the usage of "At operation mode" in detail.....If any coding is required pls also let me the way to do....

Hi
It s nothing but the NORMAL operation Mode or NIGHT operation mode
So you can define the relative operation moade and accordingly can set the time to execute the job as per the settings.
You can enter any name for the operation mode, but ensure that it is meaningful and that it makes the task of the operation mode clear.
<b>Reward points for useful Answers</b>
Regards
Anji

Logs for 'Operating mode' change in mirroring

Logs for 'Operating mode' change in mirroring
Hi Everyone,
Is there any log,that shows when the Operating mode of a database involved in mirroring(SQL SERVER 2008 R2) has been changed from asynchronous to synchrous(or vise versa).
Regards,
Aspet
A.G

Try looking into trace log files
DECLARE @filename VARCHAR(100), @filenum int
SELECT @filename = CAST(value AS VARCHAR(100))
FROM fn_trace_getinfo(DEFAULT)
WHERE property = 2
AND traceid = 1
AND value IS NOT NULL
SELECT @filename
SELECT @filename = substring(@filename, 0, charindex('_', @filename)+1) + convert(varchar, (convert(int, substring(left(@filename, len(@filename)-4), charindex('_', @filename)+1, len(@filename)))-4)) + '.trc'
SELECT @filename
SELECT gt.EventClass,
te.Name AS EventName,
gt.TEXTData,
gt.NTUserName,
gt.NTDomainName,
gt.HostName,
gt.ApplicationName,
gt.LoginName,
gt.SPID,
gt.StartTime,
gt.EndTime,
gt.ObjectName,
gt.DatabaseName,
gt.FileName
FROM [fn_trace_gettable](@fileName, DEFAULT) gt
JOIN sys.trace_events te ON gt.EventClass = te.trace_event_id
WHERE EventClass = 116
AND TEXTData LIKE '%Alter
database%'
ORDER BY StartTime;
Best Regards,Uri Dimant SQL Server MVP,
http://sqlblog.com/blogs/uri_dimant/
MS SQL optimization: MS SQL Development and Optimization
MS SQL Blog:
Large scale of database and data cleansing
Remote DBA Services:
Improves MS SQL Database Performance

Unable to change the operating mode in informatica admin tool.

hi
i have installed Informatica 8.6.0
my repository service is running . and i have also created the integration service but its not running, the reason as i fount out in various blogs is that my repository is iin exclusive mode .
so , i tried to change it to normal mode . but the problem is as i select normal in the drop-down list in general properties operating mode option and click ok , nothing's happening a and the page error is coming as shown below:
Can't move focus to the control because it is invisible ,not enabled or of a type that does not accept the focus
Is this an error of internet explorer ??? i am using IE 7.or are there any options that i need to enable???
what should i do in this case???
plz help !!!!
Edited by: Nikhil.S on Jun 8, 2011 3:37 AM
Edited by: Nikhil.S on Jun 8, 2011 3:41 AM

I got the same error and after I tested with firefox and everything.. I found out the issue (in my case):
- Under Database properties, The value for "ConnectString" property contains a space at the end.
-Example "host.oracle.com "
- Solution: I remove the space at the end , save it, and Now I can modify the operatingmode to Exclusive
Edited by: hcamacho on Jun 24, 2011 1:53 PM

Operations in Routing

Can I have two operations in routing?In one operation operation number can be 10 for other it is 20.For operation 10 i hv to show consumption of sfg & for operation 20 i hv to show production of FG.i will confirm by co11n first for operation 10 & then for 20.Is it right?for automatically good recipt for operation 20 which control key will be used & at the time of confirmation it will show movement type 101.Plz reply.

Dear ,
Find belwo the answer :
Can I have two operations in routing?
Yes .You can have .For operation 10 -Please assing the Control Key PP01.You can assing the same in Work centre Default tab so that it will be automatically picked up in Operation 10 .In Co11n , You can confirm the same .
For operation 20 which u hv to show production of FG-Assing the Cpntrol Key PP03-Auto Good recipet Active so that in CO12 /CO11N , you can keep the Operation Number 20 -Final Confirmation -Hit the Good Movement tab -Check the Movement Type 101 ,Storage Loaction -either Raw or FG as per your business requirement and then Save .
However , you can use Back Flash opetion for SFG in FG production order .For that you need to have the below set up :
Backflash can done based on the following set up :
1.In material master MRP2 view of the item , Backflash field should be kept -1-Alaways back Flash
2.In work Center where the routing operations are done , -Goto-Basic Data View -Back Flash Indicator -to be marked .
3.In routing Componenet Alocation -Item Line -Back Flash Indicator to be ticked once assinged to a particualr operation .
Priority will be always Work centre even you keep the Material master MRP2 view kept always back flash .
Hope this will solve your problem
Regards
JH

Manual Switch over the operation modes

Hi,
What's is purpose of RZ03(Manual Switch Over the Operations Modes)? Where extactly useful?
Regards
Basis Admin

Hi,
Operation Modes are the best way to change the amount of processes in the system, Administrators usually prefer more dialog processes during the day to deal with the users requests and more batch processes during the night to deal with all the system jobs, reports, archiving, etc.. The manual switch is used to change the Operation mode instantly to deal with a special demand, like heavy reporting, special month end jobs, testing, etc...
Hope this help!
Juan
Please reward with points if helpful

Can't switch operation mode after backup offline

Hello:
Every sunday system stop at 9:30 a.m to backup offline at 16:00p.m
System start at 23:00 p.m.
Operation mode
Day : 7:00 a.m 22:00 p.m
Night 22:00 p.m 7:00 a.m
This monday dont switch operation mode night to day and disp+work get
busy .
Nobody could access the system until it is manually reset.
Can anybody help us?
Regards.

You have following options.
1 .try to adjust the operation mode as example given below.
Add an additional operation mode Except for the duration of backup .
Example:
7:00 a.m. - 7:00 p.m. DAY (normal operation mode)
7:00 p.m. - 7:00 a.m. NIGHT (normal operation mode)
3:00 a.m. - 4:00 a.m. EXCEPT (Backup operation mode)
4:00 a.m. - 7:00 a.m. NIGHT (exception operation mode)
2.See if you get and error message in sm21 after offline backup.
3.delete the operation mode and create new .
4.try to change the timings of day and night operation mode.
what is your OS and DB and Rel?
hope it helps.
Amit

Profile consistency check when operation mode change

If the number of work processes in the profiles is changed, the system can no longer switch operation modes until after a restart of the instance. It's therefore necessary to adjust the configuration of the operation modes after a change to the profiles.
In above paragraph, I don't understand why the system can not switch mode if the number of wp in profile is changed? Does system will compare wp number in profile with currently running wp number before the operation mode switch? Please advise.
Thanks.
James

Yes, I can understand it, when the number of work processes is changed, we need redefine the operation mode.
But I am confused this sentence "If the number of work processes in the profiles is changed, the system can no longer switch operation modes until after a restart of the instance. "
After the number of work processes in profile is changed, I think it will not impact instance immediately until restart the instance. According to this sentence, it seems when I change the parameter in profile, it impacts the instance immediately and the system can not switch operation mode right now if we don't restart the instance. Is it reasonable? And I think the operation mode still need redefine even if we restart the instance, since scenario in Ralph's description. Is my thought right?
Thanks so much.
James

Unvisible tables in the operating mode (MAC)

hi everyone
a customer did install the contribute cs4 for macintosh.
i know contribute only for windows.
is it possible that he doesn't see the tables in the
operating mode?
i can't overtake his screen to see it.
thanks

can you rephrase the question?
are they trying edit a page that has html tables in it, but
they don't see
the table cells in ccontribute?
url address to the page they are trying to edit?
is the html syntax in the page correct?
Alan
Adobe Community Expert, dreamweaver
http://www.adobe.com/communities/experts/

NCipher server not in operational mode : Cisco NAC

One of the NAC server got rebooted and then while restart i am getting an error nCipher server not in operational mode. Please change the settings on back of the card. Also error-sshd-server not running.
Please let me know how to make the ncipher in operational mode and change the mode of NAC in FIPS mode.
It is very urgent. Please let me know the solution.
Regards,
Tarunava

The Cisco NAC is 3315 and software version is 4.1.2.
Below are the error logs.
[root@PLHO_CAS_01 ~]# cd /perfigo/common/bin/
[root@PLHO_CAS_01 bin]# ./test_fips.sh info
Installed FIPS card is nCipher
Info-FIPS file exists
NFastApp_Connect failed: ServerNotRunning
Error-card is not in operational mode
Error-httpd worker is in Non FIPS mode
Error-sshd not up
System not in FIPS mode
[root@PLHO_CAS_01 bin]#
[root@PLHO_CAS_01 ~]# /etc/init.d/sshd start
Starting sshd:WARNING: initlog is deprecated and will be removed in a future rel
ease
key_load_private_pem: RSA_blinding_on failed
Could not load host key: /root/.perfigo/sec/tomcat.key
Disabling protocol version 2. Could not load host key
sshd: no hostkeys available -- exiting.
[FAILED]
[root@PLHO_CAS_01 ~]# /etc/init.d/httpd start
Starting httpd: Syntax error on line 167 of /etc/httpd/conf/httpd.conf:
DocumentRoot must be a directory
[FAILED]

Branch operation and return operation for routing in alternative sequence

Hi all experts.
I would like to ask which table and field store the value of branch operation and return operation for routing in the alternative sequence. I can only find them in structure (PLFLD-VORNR1 and PLFLD-VORNR2) but I want the table field of them. Would anyone please suggest a solution? Thank you.

Hi,
look in table AFFL, here the BKNT1 and BKNT2 refer to those vornr1 and vornr2 of the operation. For example in user-exit ZXCO1U01 you will find the values (BKNT1/2) in the sequence table, and when, for example, filling the LOIPRO01-Idoc, you can use the found VORNR for the E1AFFLL-segment.
See coding for example on determining VORNR1/2 (sequence_table/operation_table as in user exit EXIT_SAPLCOBT_001):
SORT operation_table BY vornr.
LOOP AT sequence_table INTO l_sequence.
    MOVE-CORRESPONDING l_sequence TO l_affl.
* Read the operation table to determine the vornr1 and vornr2
*via the value of field BKNT1/2
    IF NOT l_sequence-bknt1 IS INITIAL.
      READ TABLE operation_table INTO l_operation
      WITH KEY aufpl = l_sequence-aufpl
               aplzl = l_sequence-bknt1.
      IF sy-subrc = 0.
        l_affl-vornr1 = l_operation-vornr.
      ENDIF.
    ENDIF.
    IF NOT l_sequence-bknt2 IS INITIAL.
      READ TABLE operation_table INTO l_operation
      WITH KEY aufpl = l_sequence-aufpl
               aplzl = l_sequence-bknt2.
      IF sy-subrc = 0.
        l_affl-vornr2 = l_operation-vornr.
      ENDIF.
    ENDIF.
Cheers,
S.

CA02: Delete Operation from Routing

Hello,
My question is: how can i delete an operation from routing, like in CA02, but using FM or BAPI and avoiding Batch Input?
Right now it's done with Batch input, but when there is more than one routing per material it crashes, due to extra screens.
Thanks in advance...

Dear,
if you have created operation through CA01 then
Go to CA02-- Select your operation and then header manu Edit--Delete or use (Shift+F2) and save it.
If in CO01 production order then in operation details screen and select your operation and delete it.
Please try and come back.
Regards,
R.Brahmankar

WRT54GC Operation Mode: Router Or Gateway

Similar Messages

Maybe you are looking for