WRT54GH - can't log in the router admin page

Thank you for your answer, I have one Linksys router model WRT54GH. I didn't change the login (admin), but when I try to enter in the system, it doesn't recognize the information and asks new login and password. I reset it more than one time but without success. I didn' t atualize the firmware. I only reset the system. What can I do to access the configuration area? Thanl you very much.

First of all here are the steps for the physical connectivity for the router:
The router’s power adapter needs to be plugged to your router and into an available power outlet.
If using a wired connection, the first Ethernet cable needs to be plugged to the computer’s LAN port into any of the router’s blue numbered Ethernet ports.
The second Ethernet cable should be plugged to the modem’s Internet port and the other end into the router’s yellow Internet port.
Ensure that you have no firewall enabled that may prevent the router from being detected.
After doing the physical connectivity check what IP address do you get from the router... You can check the IP address in the following manner:
# Click on Start -> All Programs -> Accessories -> Command Prompt.
# A black pop up box should come up, type: "ipconfig /all" …
There check the IP address and Default Gateway under LAN.
If you get the valid IP address then try accessing the router’s web-based setup page. Here is the link for the same: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=3d655af76e21457fa8b71a0c3a2a0c9c_3676.xml&pid=80&r...

Similar Messages

Unable to Access Router Admin Page

So I have a weird situation where my router is working fine to allow me access to the internet, yet I am unable to access the router administration page, 192.168.1.1 This occurred after the router froze up tuesday. I reset the router to factory defaults and have since been able to get online, but not access admin page. Router is a Linksys WRT-54GS V 7
Modem is motorolla SB1505
ISP is earthlink, but in NYC so its actually off the Road Runner network. Cable connection obviously. - I attempted to access 192.168.1.1 with both Mozilla Firefox and IE 8. FIrefox gives an "Unable to connect" error message. IE 8 redirects me to search engine results (yahoo in this case).
-Ipconfig confirms default gateway and DHCP server is 192.168.1.1, subnet mask 255.255.255.0
- I am able to ping the router with <1ms times.
- I have tried resetting router to defaults again, but same issue occurs.
- I am able to get online and access web pages, etc.
- Tried resetting up the router using the Linksys setup program, but it error every time saying "please connect router for broadband"
- Router worked fine with me able to access admin page until it froze up yesterday.
- Wireless works fine. Though the network is unsecure atm, since I can't access router admin.
- I've also tried disconnecting all other devices from the router except my computer and modem. Still wont let me access router. System is running windows 7 PRO, fully updated. However, I can't access the router either on 2 other computers at home which run windows XP PRO SP3. System Specs CPU: Intel i5 running at stock speeds
Mobo: Gigabyte P55-UD4P
Ram: Gskill Ripjaw, 4 gb DDR3-1600 7-7-7-21
HD: Intel X-25 M 80 gb G2.
PSU: Corsair CMPSU 750 TX
GPU: Diamond ATI 5850 Anyone have any ideas on whats wrong here? Did i miss something obvious? Would greatly appreciate any help as having an unsecure wireless network in the middle of NY isn't the best idea. Thanks!
Message Edited by Banthracis on 11-06-2009 04:25 PM

I am once again unable to access the on-line Router admin page. When I use the EasyLink Advisor and click ADVANCED settings it pulls up the browser but goes nowhere. If I type in the address directly it does the same thing. The address I'm typing is correct. I know because if I unplug the router for a minute, I can get on using the EasyLink or entering the address directly into the browser. Then I sign in and can access the pages.
Why do I have to keep resetting the router to access the router admin pages? It doesnt matter about virus protection, firewall, what version of Windows I'm using, what browser I'm using...the only thing that matters is resetting the router.
And now I have a new problem. When I attempt to go online with my new netbook, it causes my wired-to-the-router desktop to loose the connection, even though I reset the router and "added it as a new device".
I was using Homegroup to access the netbook the first day I got it. Now I cannot access the netbook or the network from the netbook, without resetting the stupid router every single time. I am not using mac address filtering and have the router set to allow 9.
Getting fed up with this router and I never get an answer from Linksys as to why I can never access the router admin pages without resetting the stupid router.
I can get the netbook on other people's wireless networks (using their password) but cannot get onto my OWN using my password.
Does anyone have any ideas? I'll try anything before yanking this thing out and buying a different brand of router. Yeah I'm mad, sorry.
Wired desktop Windows 7 Home Premium 64/IE8/using Windows firewall and MS Security Essentials. Netbook is W7 Starter, Norton Internet Security 2010. But none of this matters. Because I had the same problem with this router using Vista64, IE7, no firewall, no a/v, IE32 & 64 bit...all those variables yet the only thing that works is resetting the router.
SO WHAT DOES MATTER? Help me before I trash this thing please.
mlure

EA6350: Set up worked fine, my nw is working, but now I can't login to the router

The setup went well, I was able to configure the network wirelessly on the web-based console. The networks are working fine (both 2.4 and 5Gz). A few days have passed and I wanted to check out some of the other management feature of the console (checking who is logged in, etc) and keep getting the message below. Why can't I access the router?
Your router was not successfully setup.
Follow these steps:
1. Press and hold the red Reset button on the back of your router for at least 10 seconds.
2. During reset, the router will restart and the power light will flash. Wait until the power light is solid.
3. Reconnect this computer or device to the default wireless network. You can find the wireless network name and password in the Quick Start Guide or on the label on the back of your router.
4. When finished, click here to run through setup again.
If you follow the steps above and see this error screen again, visit our website for troubleshooting tips or to chat with a Customer Support representative. To access the website, you may have to use a different computer or mobile device that has Internet access, or connect this computer directly to your modem.
www.linksys.com/supportError code: 2318

Are you using the local log in link or the smartwifi log in? Try the local log in link.
PC 3rd Party Security Software Configurations
Turn off all anti virus and firewall programs on PC while testing. 3rd party firewalls are not generally needed when using routers as they are effective on blocking malicious inbound traffic.
Turn off all devices accept for one wired LAN PC while testing.
Disable any downloading client software managers, i.e. Torrents or similar.
PC Web Browser Configurations
What browser are you using?
Try Opera or FF? If IE 8, 9, 10 or 11, set compatibility mode and test again.
Disable any security browser Add-ons like No Script and Ad-Block or configure them to allow All Pages when connected to the router.
Clear all browser caches.
Be sure to log into the Admin account on the router.
Try turning off these features in Chrome:
Top right corner, little bars for options > Settings > Settings (on left) > Show advanced settings.
Uncheck these:
Use a web service to help resolve navigation errors
Use a prediction service to help complete searches and URLs typed in the address bar
Predict network actions to improve page load performance
Enable phishing and malware protection

Can't log on to tomcat admin, HELP PLEASE!!

Hi All,
I am trying to log into the tomcat admin tool but it just won't work. I have created a username and password in the tomcat-users.xml file but I still can't log into the admin tool can anyone help. PLEASE
Howerd

This is really a question which should be directed to [email protected] mailing list.
What exactly is the problem? Unusual behaviour, error messages would be usefull.
Are you able to see the admin login screen?
When you created this user, did you add the admin role?
<user username="admin" password="admin" fullName="Administrator" roles="admin,manager"/>

After upgrading to Snow Leopard, I can not log into the computer. What Can I do?

after upgrading to Snow Leopard, I can not log into the computer. What Can I do?

SqueezeAce wrote:
after upgrading to Snow Leopard, I can not log into the computer. What Can I do?
Stick the 10.6 disk into the machine and reboot holding the option/alt key down on a wired/built in keyboard.
On the second screen, under the Utilities menu is a Password Reset, use it.
Step by Step to fix your Mac
What this will do is reset the password and the user account permissions in the process.
You might have problems with Keychain afterwards, to fix that.
https://support.apple.com/kb/HT1631 https://support.apple.com/kb/TS1544
If your still having trouble, look through these User Tips
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents#/?p er_page=50

I can't log into the Itunes store,says I need to update my security but the link won't open in Explorer, bad http!

I can't log into the Itunes store with my Apple ID.Says I need to update my security but the link doesn't work,bad http.Get internet explorer canot connect message.

Good day Goose253501,
It sounds as though your iPhone is having some difficulty accessing the App Store servers when attempting to sign in. I would suggest that you troubleshoot using the steps in this article -
Can't connect to the iTunes Store - Apple Support
Thanks for using Apple Support Communities.
Safe computing,
Brett L

I can't connect to the router in my home. Things were working fine as usual - I attended school and connected to their WiFi network as usual. When I returned home I could not connect to my own home router. The Ipad seeks the network but nothing happens

I can't connect to the router in my home. The Ipad seeks the network but nothing happens. I went to school and connected to their WiFi network as usual with no problems. When I returned home I could not connect to my home router. The Ipad seeks the router number but nothing happens. I rebooted the Ipad a few times in the school. The numbers identifying the router, etc. on my Ipad no longer appear there.
TThe Ipad guide says to connect to the WiFi use setup but I can't find the setup program in the Ipad.
I reset the network settings to the factory defaults but this doesn't fix the problem.
What can I do to reconnect to my home router?

Some things to try first:
1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
4. Go into your router security settings and change from WEP to WPA with AES.
5. Renew IP Address: (especially if you are droping internet connection)
    •    Launch Settings app
    •    Tap on Wi-Fi
    •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
    •    In the window that opens, tap on the Renew Lease button
~~~~~~~~~~~~~~~~~~~~~~~~~
iOS 6 Wifi Problems/Fixes
How To: Workaround iPad Wi-Fi Issues
http://www.theipadfan.com/workaround-ipad-wifi-issues/
Another Fix For iOS 6 WiFi Problems
http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
Fix For iOS 6 WiFi Problems?
http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
iOS 6 iPad 3 wi-fi "connection fix" for netgear router
http://www.youtube.com/watch?v=XsWS4ha-dn0
Apple's iOS 6 Wi-Fi problems
http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
~~~~~~~~~~~~~~~~~~~~~~~
How to Fix a Poor Wi-Fi Signal on Your iPad
http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
How to Fix: My iPad Won't Connect to WiFi
http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Connect iPad to Wi-Fi (with troubleshooting info)
http://thehowto.wikidot.com/wifi-connect-ipad
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I can't log in the App store because an from Zambia which is not listed in Apple outlets. How do i go around this as apple products are using globally and not only in the listed countries. My product is a Mac book pro.

I can't log in the App store because am from Zambia which is not listed in Apple outlets. How do i go around this as apple products are used globally and not only in the listed countries. My product is a Mac book pro. i feel this limits how i can use my product

Unfortunately you have taken an Apple product outside of the area where Apple currently does business. There isn't legally a way around this. Apple cannot license apps to you where you currently live.

Airport extreme software will not install on vista, how can i still configure the router?

airport extreme software will not install on vista, how can i still configure the router? Trying to help someone with vista get an airpot extreme configured. 10.0.1.1 does not work, the software will not install correctly on their vista machine. How can I get into the base tation and lock it down?

Hi - Vista can be tricky - I need more info to see if I can be of some help - first, is the Vista machine a desktop or a laptop and is it fully up to date with Windows Update (sp2 or higher)? - next, are you trying to install Airport Utility version 5.5.3 which is the correct one for Vista? - and finally, what do you mean "it will not install" - what kind of error messages or evidence are you getting?

I can not log onto the App Store...

it has been going on now for over 3 weeks...I had a lightning strike and blew out the on board ethernet ports on my Macpro so I use a ethernet to usb adapter now and that works fine for everything including iTunes but I can't log into the App Store, the error is "An unknown error has occurred" I have called and they told me to go to the Genius Bar...did that and the couldn't help and called support and they told them that they would look into it and get back to within 24-48 hours and I have still haven't heard a thing!!! This is very frustrating and I have had several cases opened up about this and nothing is working. Does anyone have any ideas on what to do? Thank you.
Charlie O.

Guess, you only have another issue with the app store problem. Some cannot login, some are caught into a loop of password prompts...
All is related to Macs with MacOS 10.4.7 - so again.
There are two different solutions trials, one is to go to close all applications then navigate to /var/db/crls and delete there the files crlcache.db and ocspcache.db - reboot the system, empty trash and see if this solved the problem.
If not, second chance is to reset the certificates, mentioned here:
Delete the files /var/db/crls/crlcache.db and /var/db/crls/ocspcache.db. These can be found using Finder’s Go >; Go To Folder menu (Cmd + Shift + G). This resets the cache of accepted certificates in the system. It doesn’t remove them, it just forces the system to rebuild the caches upon restart.
Open Keychain Access (/Applications/Utilities/Keychain Access). Select Certificates in the Category picker on the left side. In the search bar, type in the word Class. Look through that list, and find any certificates that have a blue + symbol over their icon. These are the ones you need to modify.
Select one that has a blue +, and hit Command + I. Click the disclosure triangle beside the “Trust” list to show the list of permissions. Now, what we need to do is to set this certificate to use the system defaults. However, for some reason, when you select it, it doesn’t save. So what you need to do is this. Under “Trust”, where it says “Secure Sockets Layer (SSL)”, change the dropdown menu to say “No Value Specified”. Then, close the window. It will ask for your administrator permissions. Then, open the info pane for that certificate again. Under “Trust” again, now set the dropdown that says “When using this certificate:” to say “Use System Defaults”. You can then close out of the info pane, and enter your password again. Do this for any of the certificates that have a blue + on their icon. There should only be one or two at most.
Restart your system.
So, as you see, it start again with reseting the certificate cache and next manually working the certificates, to ensure proper system setting...
But there are evenly people who failed with this... but you can give it a try
If all fails - then we have to wait for a fix from apple

After software Update (2006-07), airport can not connect to the router

Hi,
I installed the software update 2006-07. Afterwards the airport extreme can not connect to the router anymore (NETGEAR). I use a WEP key, but even if I type the WEP Key, the airport does not succeed to the router anymore... I called Apple Care and they wanted that I install the firmware restoration. But even I didn't succeed to install the firmware restoration. On the firmware restoration web page (http://www.apple.com/support/downloads/firmwarerestorationcd12.html) is written that I have to turn on the computer and continue holding down the power button until the LED blinks rapidly followed immediately by a successive series of blinks (3 quick blinks, 3 slow blinks, 3 quick blinks). But after the LED blinks, there is not the successive series of blinks...
I know there is 2 questions in one message, but could you please help?
Thanks in advance.
Best regards,
Eric
MacBook Pro Intel Core 2 Duo Mac OS X (10.4.8)

http://forums.macosxhints.com/showthread.php?p=337100
Exactly the same problems as mentioned here kernel panics, etc. How could this have passed Apple Quality Checks?
Tue Dec 5 09:26:34 2006
panic(cpu 0 caller 0x000A8800): Uncorrectable machine check: pc = 000000003931288C, msr = 0000000000149030, dsisr = 40000000, dar = 000000003A207F7E
AsyncSrc = 0000000000000000, CoreFIR = 0000000000000000
L2FIR = 0000000000000000, BusFir = 0000000000000000
Latest stack backtrace for cpu 0:
Backtrace:
0x00095138 0x00095650 0x00026898 0x000A8800 0x000A7A90 0x000AB780
Proceeding back via exception chain:
Exception state (sv=0x39D1B780)
PC=0x3931288C; MSR=0x00149030; DAR=0x3A207F7E; DSISR=0x40000000; LR=0x39312858; R1=0x2285BA10; XCP=0x00000008 (0x200 - Machine check)
Backtrace:
0x39312848 0x393139B8 0x39333874 0x393336BC 0x393332F0 0x3933313C
0x002D124C 0x393314AC 0x39332774 0x002EB838 0x0008C6A4 0x0002921C 0x000233F8 0x000ABAAC
0x00000000
Kernel loadable modules in backtrace (with dependencies):
com.apple.iokit.AppleAirPort2(405.1)@0x392f4000
dependency: com.apple.iokit.IONetworkingFamily(1.5.0)@0x386e6000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x32922000
Exception state (sv=0x39D3A780)
PC=0x9000AB48; MSR=0x0200F030; DAR=0x003B8000; DSISR=0x42000000; LR=0x9000AA9C; R1=0xBFFFCCA0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.8.0: Fri Sep 8 17:18:57 PDT 2006; root:xnu-792.12.6.obj~1/RELEASE_PPC
Just by enabling the airport express card. Now I wonder what triggers the bug. Because I rebooted several times after the update. One thing I did see was the signal strength going less strong in the past days. Since today I cannot use it at all.

I sold my ipad 2 and didn't take out my apple id. how can i log off the ipad with out having it in hand?

I sold my ipad 2 and didn't take out my apple id. how can i log off the ipad with out having it in hand?

You can't. But the buyer more than likely restored it because he/she could not use your Apple ID.

HT204266 I can not log into the App Store, even though I am logged in to iTunes. ? Help please :)

I can not log into the App Store, even though I am logged in to App Store and my password is entered into the settings. This appended after I accidentally switched to the British version of iTunes and I logged out and back in to get to the US. Now, I keep getting an error message that I can not log into the App Store. I have tried updating it to the computer and restarting, but still keep getting the error message. Help please! :)

I am afraid all apps are tied to the Apple ID they are purchased with and are not transferable.
Your son have to buy those apps with his own Apple ID and start from scratch.

HT1206 I can't log into the Itunes store. I type in my Apple ID and my password and the message "This Apple ID cannot be used for the iTunes Store." "Enter another Apple ID." I need help on fixing this.

I can't log into the Itunes store. I type in my Apple ID and my password and the message "This Apple ID cannot be used for the iTunes Store." "Enter another Apple ID." I need help on fixing this.

Yeah I'm starting to see a ton of forums posts right now about the same thing :/ I wonder what's going on

Need help accessing the router web page. I have been tol...

Need help accessing the router web page. I have been told my router is acting like a switch and the IP address is not in the proper range. I have tried reseting the router (hold for 30 sec and unplug for 5 mins). Didn't work.
thanks

What router are you using? Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS (not the WRT54GS).
You need to try again to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is dead.
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Message Edited by toomanydonuts on 01-21-2008 04:40 AM

WRT54GH - can't log in the router admin page

Similar Messages

Maybe you are looking for