WRT54GL - Cannot access the router

I can't access the router "WRT54GL" from 192.168.1.1.
I don't know username and password.
Could you help me please?

Before I suggest you for any troubleshooting steps. I would like to know few questions. Let me know the IP address from the router? Here are the steps to check the IP address.
You can check the IP address in the following manner:
# Click on Start -> All Programs -> Accessories -> Command Prompt.
# A black pop up box should come up, type: "ipconfig /all" …
There check the IP address and Default Gateway under LAN….
If the Default gateway is '192.168.1.1' then in case once reset the router... Steps to reset the router:
Push the reset button on router for 30 seconds, turn off the router wait for 30 seconds and then power it on.
Power light should blink when you perform the reset process.
The default password is “admin” and you may leave the User name field blank.
Here is the link for accessing the router's web -based setup page: http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=3676&userrole=Linksy...

Similar Messages

  • I cannot access my router's web configuration interface since Firefox 4. It does not let me enter a password with the username blank (as specified by the router manufacturer). Is there a workaround for this?

    since updating to Firefox 4, I cannot access my router's configuration page (http://192.168.x.x). When prompted for the username and password,Firefox's log in window does not accept a blank username field (The router does not require a username, only a password, and it's the default password). If I click OK, the password entry just comes up again. This works fine in other browsers. Is there anything I can do about this?

    I had this issue, too, and fixed it by turning off the option "Tell Websites I do not want to be tracked" under Options->Advanced->Browsing.

  • Is there a way to access the web-based setup for my router if I cannot access the internet?

    Okay, I need to change the ip address settings on my router. I have a WRT54G Wireless router. I cannot access the internet on my computer connected to the router, and do not know how to change the router settings without accessing the web-based setup page. So, back to my question. Is there a way to access this page if I cannot connect to the internet?

    On the back of the router is a small reset switch. Using a paper clip or other small item, press the switch in and hold it for a few seconds. This will reset the router to the default IP address of 192.168.1.1. Enter that address in your web browser, and be sure your computer is attached to the router by an Ethernet cable. Don't attempt to do this using the wireless connection.
    Once you have reached the web configuration utility you can change the DHCP settings.
    To give your PC a static IP address you will need to open your network connections panel and, assuming your using Windows XP, make the changes from dynamic IP to static there.

  • WRT54G router cannot access the Internet

    My wireless PC can access the router but cannot access the Internet.
    When I ping linksys.com - the ping times out; however, when I ping my ISP I get 4 pings back. When I ping the router the ping is successful as I get 4 pings back.
    I am sure there is a fix for this problem. Can anyone help me get connected to the internet?
    Thanks
    I just got DSL in my area and installed it. I have a Linksys WRT54G router and a zyxek 660R DSL modem. I have a PC #2 in the room down the hall and a PC #1 in another room. I have a Wireless-G USB adapter in PC #2 (this is the antenna for the wireless connection). Everything is installed and PC #1 can connect to the internet through the modem and router. However PC #2 can only reach the access point (router) and will not access the internet. I can connect to the internet for PC #2 when an ethernet wire is used directly but it is not great to have a wire running down the hall. I pinged the router from PC #2 and the echos look fine. So it can certainly reach the router. When I use the Local Network tab and click on DHCP Clients table both PCs are displayed. So how can a PC use a wireless connection to reach the internet? I have spent 4 days already trying to get this to work. My ISP can't seem to help.
    Thanks for your help.

    hi... logon to router's setup page and try changing channel to 1 or 11, click on the advanced wireless settings and try reducing beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmware on the router...also
    if you are using Win XP system try uninstalling the adapter from the computer...click on start >> programs >> wireless G USB adapter >> uninstall, put the CD in for the adapter and restart the computer, one window pops up "found new hardware" try installing the drivers, no need to install WLAN software or utility and use windows WZC (wireless zero configuration) to manage wireless connection...check whether it works for you or not and let me know the results.

  • Cannot connect using Accessing the Router's Web-Based

    I'm trying to update firmware, I have done all the step to access the router's web-based.. I connected DSL to the Ethernet port on the router, from the router I used another Ethernet cable to connect the router to my laptop.. I can't get an internet connection.  The reason why I'm doing the update I have been using WRT54G2 V1 with no problems, all at once I can't connect to the internet using the router.  I was told that I need to perform a firmware update.
    Thank you for the help

    What' s the ip address and the default gateway are you getting on the computer ?
    Connect the DSL modem to the Internet port of the router then use port number one on the router to connect the computer.
    Click on Start > Run > type CMD hit Enter command promt window will appear on the screen.
    In the command promt window tupe "ipconfig" hit Enter. Now you will see the ip address and the default gateway on the screen. Use the default gateway to open the setup page of the router.

  • I cannot access the internet, I tried to answer that said to go to settings, safari, tap clear history, cookies and cache, cut off, then on, but it did not work.  When I go to internet the screen is grey??? please help I am a new user!!

    I cannot access the internet the screen is grey, I have tried by using the answer from someone but it does not work...I went to settings, tap safari, then clear the history, cookies, and cache, then turn off ipad.  When I did that twice, it did not work.  How long does it take for the clear history to work?  I am a brand new
    user of the ipad2 and I am disappointed that this is happening already.

    Have you been able to access the internet previously and now it's suddenly not working, or are you still trying to access the internet for the first time on your iPad?  Are you at home trying to connect through your home router?  If you are at home, did you put your home routers encryption code as your password?  The encryption code is what your iPad is looking for and it is usually found on the router and is typically a 13 digit combination of letters and numbers.  Let us know......

  • I did a software update on my ipad and now cannot access the internet. how can i fix this?

    I did a software update on my ipad to 8.1 and now cannot access the internet.  How do I fix this?  My mail updates, but to get internet access I had to move from wifi to cellular data, and now even cellular data does not allow me access.

    Hi Go to settings Reset Network Settings After Reset you need to enter your Router wireless key Before you do this turn off your Router for 30 seconds Also an option is to go on Websites for your make of Router look for any Firmware updates but you can do this later. Cheers Brian

  • TS1398 my ipod touch worked fine on my wifi home network. After not using my ipod for a month or so, I cannot access the internet. All other devices work fine. Thus, its not my home wifi....I tried resetting...forgetting....nothing works...still cannot ac

    hello - my ipod touch worked well until a couple of months of non-use. Now, I cannot access the internet thru my wifi. All my other devices have no such problem. I have tried resetting wifi, "forgetting network" turning wifi off and on....nothing works....can anyone help?

    - Reset the iPod. Nothing will be lost
    Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router.
    - Reset networks settings: Settings>General>Reset>Reset Network Settings
    - iOS: Troubleshooting Wi-Fi networks and connections
    - iOS: Recommended settings for Wi-Fi routers and access points
    Does the iPod see the network? Error message? Does the iPod connect to other networks?

  • I cannot access the internet using firefox. The little toolbar identical (the far upper right in the screen) pops up and nothing else happerns. This has only started very recently and I have not had this problem in the past.

    When I click on the icon for firefox, a little toolbar (the one you see in the top right corner of the screen) pops up and nothing else happens. I'll close it out and retry, with only the same results. I tried Firefox safemode, with the same result. Like there is something blocking me, but I don't know what. It doesn't matter if I've been on the computer for some time or just started up, I cannot access the web thru Firefox. This has only started in the last couple days. Previously, I've never had this problem. I haven't loaded any new programs anytime recently to account for this. I use Norton for my anti virus program which is the newest and had since end of December. I am not happy having to use the windows internet explorer, so would be very happy to get this resolved. Should I uninstall the mozilla program, and then reinstall it?

    "I have an ethernet cable in port 1 on my computer. That is configured manually to access ther office network."
    Do you have a "real" IP address or a private (192.168.x.x, 10.x.x.x, 172.x.x.x) IP address?
    "The wireless router was connected to the company server only for the purpose of getting me online through Airport because I couldn't access it using an ethernet connection"
    Could not access it because their network security blocked you by intent, or had some unknown technical difficulty?
    Unless you are blocked by intent or ommission (if they have to explicitly allow your machine) I can think of no technical reason why your wired connection should not both get you on their network and on the internet in general. You should not need to be dual homed (though dual homing should work as well).
    Please answer the questions above when you can - I think solving the wired LAN issue will be easier if you are not being intentionally blocked.

  • Need help accessing the router web page.  I have been tol...

    Need help accessing the router web page.  I have been told my router is acting like a switch and the IP address is not in the proper range.  I have tried reseting the router (hold for 30 sec and unplug for 5 mins).  Didn't work.
    thanks

    What router are you using?  Almost all Linksys routers use 192.168.1.1 as the default local IP address, but there is at least one that uses 192.168.16.1 , namely the WTR54GS  (not the WRT54GS).
    You need to try again to reset the router to factory defaults.
    To reset your router to factory defaults, use the following procedure:
    1) Power down all computers, the router, and the modem, and unplug them from the wall.
    2) Disconnect all wires from the router.
    3) Power up the router and allow it to fully boot (1-2 minutes).
    4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
    5) Power down the router.
    6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
    7) Power up the router and allow it to fully boot (1-2 minutes).
    8) Power up the computer (if the computer has a wireless card, make sure it is off).
    9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
    10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank (note: a few Linksys routers have a default user name of "admin" (with no quotes)), and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
    If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
    If you cannot get "Reply from ..." in step 9 above, your router is dead.
    If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt. In this case, use the Linksys tftp.exe program to try to reload your router with the latest firmware. After reloading the firmware, repeat the above procedure starting with step 1.
    If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
    Please let me know how things turn out for you.
    Message Edited by toomanydonuts on 01-21-2008 04:40 AM

  • Can not port forward on WRT54GS v6 "You cannot use the router IP"

    Hello, I'm trying to open a port number, but when I try to use my router's IP, the following message appears
     "You cannot use the router IP, network, or broadband address"
    [IMG]http://i45.tinypic.com/107qond.jpg[/IMG]
    My ADSL was working as a NAT behind a NAT connection, so I had to change my Local IP Address to 192.168.2.1.
    Router: WRT54GS v6 firmware 1.52.8 (latest)  -  Bellsouth router: Westell 6100
    Microsoft Windows [Version 6.1.7600]
    Ethernet adapter Local Area Connection:
       Connection-specific DNS Suffix  . : launchmodem.com
       Link-local IPv6 Address . . . . . : fe80::40a9:a76e:61b3:6435%11
       IPv4 Address. . . . . . . . . . . : 192.168.2.100
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Default Gateway . . . . . . . . . : 192.168.2.1
    So, please help me, how can I open ports on my router? =[
    PS: I tried to use 192.168.2.100, and even though it lets me use it, it still seems not to open that port... my IP is dynamic.

    Generally: NAT behind NAT is a bad idea. There is usually no need for double NAT. Either configure the ADSL router as bridge and use the WRT for your internet connection or set up the WRT as simple access point behind the ADSL router.
    It's also unclear to me what is working or not. First I thought you can't set up forwarding at all because you get that error message. Then, in your PS you write you tried to use 192.168.2.100 and that seemed to be possible. The IP address to forward to must be the IP address of the computer to which you want to forward. Thus 192.168.2.100 is exactly the IP address you have to set up. Does this work or not?
    Also remember: with double NAT you must set up two forwardings: first on the ADSL router then on the WRT. Port forwarding is necessary to allow incoming traffic through NAT. All incoming traffic arrives on the ADSL router. Thus setting up port forwarding on the WRT only won't do a thing.
    It's also not recommend to use dynamic IPs for forwarding destinations. Dynamic IP addresses may change over time and that requires you to adjust forwardings accordingly. It's better to reserve fixed IP addresses (if your WRT supports this) or set a static IP address on the computer outside the DHCP address pool.

  • I cannot access the settings tab in the management console

    I am in the management console for my verizon d-link router and i cannot access the settings tab..
    i got to the router/verizon management console via the default gateway ip address and used the default password which worked and then tried to access settings which im assuming is the same default password.. however when i try to use the default password on the settings tab when im prompted it says that it is wrong.
    is there some different password for the settings tab?

    collado144 wrote:
    I am in the management console for my verizon d-link router and i cannot access the settings tab..
    i got to the router/verizon management console via the default gateway ip address and used the default password which worked and then tried to access settings which im assuming is the same default password.. however when i try to use the default password on the settings tab when im prompted it says that it is wrong.
    is there some different password for the settings tab?
    Have you tried to go here and select your Gateway, then follow the trouble shooting tips. Most gateways/routers default passwords at one point were changed to the serial number for security reasons. If that does not work, you may try resetting the gateway/router to get back to the default. Never leave your gateway/router with the default passwords. If you get into the gateway/router a Verizon firmware upgrade if it is a Verizon model, may even change the default password to the serial number so it is not the standard D-Link that is used with all their gateways.
    DSL help.
    http://www.verizon.com/Support/Residential/Internet/highspeedinternet.htm
    The DSL Gateways can be found here.
    D-Link 2750B Gateway?
    http://www.verizon.com/Support/Residential/Internet/HighSpeed/Networking/2750BGateway/ATLAS6561.htm
    There is a wealth of online information also available here.
    http://www.verizon.com/Support/Residential/Internet/fiosinternet.htm

  • Error: "Cannot access the web server" with BlazeDS Turnkey

    Help! I'm new to Flex and BlazeDS and Eclipse.  I was trying to setup a Flex Project using a BlazeDS/Tomcat server running from Eclipse on Windows XP per the example in flexbandit.com/archives/55#comment-269 and in (www.infoq.com/articles/blazeds-intro).   I am NOT using the Eclipse Flex plug-in.  I'm using Flex Builder for the Flex code.
    Here's what I've done:
    I installed BlazeDS and tested http://localhost:8400 - That worked.
    I setup Tomcat in Eclipse.  -  That seemed to work.
    I created a Dynamic Web Project in Eclipse - That seemed to work.
    I created the bare-bones BlazeDS Configuration under the Eclipse project and then created a basic HelloWorld java class.
    I added the destination in the “remoting-config.xml” file found in the c:/projects/workspace/ReportGenTool/WebContent/WEB-INF/flex” directory:
    <destination id="HelloWorld">   <properties>  <source>HelloWorld</source> </properties> </destination>
    When I started the application server by clicking on the server's green play button in Eclipse and then tried to open localhost:8400/ReportGenTool, I got the 404 error : The requested source (/ReportGenTool/) is not available which according to the instructions is fine.
    Next I created a Flex Project, but when I try to validate the new Flex project configuration, it gives me an error "Cannot access the web server. The server may not be running, or the web root folder or root URL may be invalid."
    When I validated the server was running after setting up the BlazeDs Turnkey, I saw the BlazeDS page.
    Now when I bring up http://localhost:8400 I get:
          Directory Listing for /
          Apache Tomcat/6.0.14
    My eclipse project is named ReportGenTool and I've overwritten the WebContent directory with the META-INF and WEB-INF directories from the BlazeDS installation (C:\blazeds\tomcat\webapps\blazeds).  According to Eclipse the server is running.
    My Flex project is named ReportGenTool and is located in another directory away from the Eclipse project directory.
         My root folder is: C:\Projects\workspace\ReportGenTool\WebContent
         Root URL: is http://localhost:8400/ReportGenTool/
         Context root is: /ReportGenTool/
    Any idea what might be wrong? What didn't I configure that needs to be configured?
    Thanks in advance.

    This is not working because your router has a direct to your web server that is not through the outside interface which is needed for nat to occur, for this to work you need to setup a loopback interface as nat outside and policy route traffic to there for your server traffic
    Bu if your server is internal why do you need nat at all? Can you not use bind with views that might be simpler
    M
    Sent from Cisco Technical Support iPad App

  • "Cannot access your router"...but router is on! Huh?

    I just want to change my guest password on LinksysE1000.  So I run Cisco Connect and get "Cannot access your router."  How can that be when it works fine otherwise?  Any help appreciated.

    So,If your Cisco Connect Software is not responding then,it this case you have to un-install the software completely from the computer then,download and install the Cisco Connect Software from linksys website and you have re-configure the entire network again.

  • Equium P200-1IR - Wireless is connected but cannot access the internet

    Hi ya,
    Need a little help!!
    I have just bought an Equium P200-1IR.
    I have turned the wi fi on.
    I can see my router which is Talk Talk.
    I can get the laptop to connect to the router and it says that I am connected,
    however I cannot access the internet.
    I tried the same process by inserting a wi fi dongle into the USB port
    on the laptop and exactly the same happens.
    We have other computers in the house that connect to the router and internet
    ok using the wireless dongle.
    I have plugged a hard wire connection from the laptop to the router and I can
    access the internet immediately with no problems, however would love
    to use the wireless feature.
    Any help really appreciated....Thanks
    Waynec

    Do you use the right channel and right encryption settings?
    This should be checked!
    It should be able to change the WLan channels in device manager -> WLan card -> Properties -> Advanced tab
    But I would also recommend disabling the encryption and password in router settings and to connect to Open Wlan of course this should be done only for testing purposes if the notebook would be able to connect to the open router, then this would mean that you used a wrong password.
    How about WLan driver update? Did you update the WLan driver? If not do that!

Maybe you are looking for