WRT54GL loses Wlan connection

Hi
I have a problem with an WRT54GL Router. It keeps losing the Wlan connection. Then I have to reboot the router to get it working again.
On some days everything works fine, and the other day I have to reboot every 5 minutes. 
I don´t use P2P. So there are not many simultaneous connections. Mostly there are only one or two Wlan Clients active.
Between the Router and the Client is only one Wall. Signal Strenght is at all times above 85%.
Does anyone have an idea what might cause this?

Try upgrading your router's firmware and reconfigure it from the scratch.
Click on this link for the instruction.

Similar Messages

  • IMac loses wlan connection after 5min

    Hey, after updating to Yosemite, my iMac late 2013" loses wlan connection every 5-10 minute. I have to turn wlan off and on, to get it back to work. Does anyone have a solution?

    Hey, after updating to Yosemite, my iMac late 2013" loses wlan connection every 5-10 minute. I have to turn wlan off and on, to get it back to work. Does anyone have a solution?

  • IMac 24" loses WLAN connection again and again

    Hy everybody,
    I bought a brand new intel-based iMac 24" and I'm very pleased with it. I just have one Problem that i can't resolve. I have a WPNT834 (Netgear) WLAN Router using WPA2. The iMac can connect without problems, speed is very good and the signal strenght is perfect, but from time to time my computer loses it's WLAN connection.
    If this happens it doesn't reconnect. I have to disable Airport, wait a minute and enable it again.
    Can anybody tell my why this happens? I mean, that the connection get lost is not so tragic, but that it doesn't reconnect is bothering me.
    Thanks in advance and regards.
    Tobi
    iMac 24"   Mac OS X (10.4.9)  

    When you click on your Airport Status do you see more then one access point? Neighbors?
    You can try changing the wireless channel on your router. That might help with the drop of connections. It's possible that another wireless access point in the area is on the same channel and causing a problem.
    Hope that helps a little,
    AL

  • N8-00 loses WLAN connection

    I have a problem when using my home router (belkin g-mimo) that after a while of using internet, and go to a  new web page I get "browser unable to connect to website". I then have to disconnect wlan and then re-connect to regain connection using the wlan widget.
    I don't seem to have this trouble on other peoples wifi networks but find this problem annoying on my own.
    I thought as a start I might be able to delete wlan settings and start again but not sure how to delete. I have tried before and wlan wizard now shows two versions of network name.
    any help appreciated.
    John
    Solved!
    Go to Solution.

    hell!!! people can anybody help me i hate My N8 i came australia on holiday the net was working good then i cant connect anymore, the wlan here but its not connecting, what i want to say the ïcon" wlan is connect but there's no tower i try deleting my wireless connection n started all again... + reset my phone but nothing coming out of it ...could anyone help me.... please i hate the day i spend my money on this damn phone since i got it... "within the warranty"they change my phone 4 TIMES, last december the warranty over, n the phone i got now, it's only 2 months old, yup just before the warranty over the phone was change n replace with a new one

  • The wlan connection of my iMac suddenly loses

    Hello communitie,
    for a couple of days the wlan connection of my iMac has suddenly lost.
    Everything is well again after deactivate and activate the airport again for an uncertain time.
    Best regards
    Kcuhen89

    I'm having the same problem with my new macbook pro (early 2011) with newest mac os. I use my business laptop (windows) on the same wlan with no connection problems...
    Any help???
    Regards
    Tom

  • WLAN Connection

    Hello,
    my wireless connection works, but at irregular intervals my MacBook Pro loses the connection to the WLAN. Sometimes I have to enter the WLAN identifier again. According to the Apple network analysis, everything works perfectly. Does anyone have any idea?
    Thanks for your Support.
    Olaf

    Run a search on this forum. There are many topics detailing what to do.
    Basically it involves putting your livebox into a "pairing" mode so that it'll accept your phone's MAC address. The WPA-PSK is printed on the livebox's label.
    Message Edited by grschinon on 17-Aug-2008 02:35 PM
    Was this post helpful? If so, please click on the white "Kudos!" star below. Thank you!

  • Qosmio G30-182: Drops Wlan connection & then cannot find any Wlans

    I currently use driver v.11.1.0.100 for Intel(R) Pro/Wireless 3945ABG, which is the latest driver I found here at Toshiba.
    My problem is that I randomly lose my wifi connection, both at my home wlan (using WEP protection) and at my university (WPA-Enterprise). After the connection drops, it is impossible to find any wlan nodes unless I reboot.
    Anyone have any suggestions on how to fix this issue? It is kind of frustrating having to reboot randomly because I need my network connection!

    There could be different reasons why the WLan connection is not stable;
    - There could be an compatibility issue between the router and WLna card.
    - The WLan driver is not up to date -> in such case update the WLan driver!
    - If you use Vista OS -> install al Vista OS updates and fixes
    - The weak WLan signal could has a bad influence and the Wlan card would disconnect
    - Check the ALL the settings in the WLan card Advanced options like mentioned [here |http://209.167.114.38/support/techsupport/tsbs/all/-TSB001435.htm]
    - Check if the same issue would appears using other WLan cards (USB WLan stick)
    bye

  • WLAN connections issues

    My N97 won't stay connected to the WLAN connection. Owned me when i was trying to download something and it switched to GPRS and took all my credit without me noticing.... Anyone can help?

    Sorry to hear that! However you can organise your access points mate! Select "always ask" in your web options. In that way, your mobile will always ask you how you want to connect, even if you lose connection to your WIFI!

  • All devices on network lose internet connection when Dell laptop connected

    I have successfully setup my AEBS network and am using two wireless clients--HP printer and Xbox access point (both 802.11 G) and a wired iMac that also is connected via Airport (so I can move it around if i want). I tried connecting my Dell Latitude D830 wirelessly and within a few minutes of connecting the AEBS loses internet connectivity. Unplugging and restarting the AEBS restores the internet but it just drops off again in less than 10 minutes. My question is, what might be causing this and what can I do about it? One peculiar thing to me is that I am using the WEP security option since the Xbox doesn't seem to support WAP2. When connecting the Xbox it reports the network as WEP but the HP printer and Dell Laptop but suggested the network was indeed WAP even though I'm clearing using WEP security. Maybe it's nothing but wanted to add for completeness.
    The Dell is running Vista Enterprise edition.
    Thanks for any help.

    I've noticed a similar issue. Any time my HP/Vista laptop is connected to my AEBS it loses the network connection at inconsistant time intervals(~10-15 min).

  • I lose the connection when closing the CMD

    Hi guys,
    I have configured a standalone listener as following:
    C:\Program Files (x86)\Java\jre6\bin> java -Dapex.home=D:\list -Dapex.images=C:\images -jar D:\apex.war
    Afterward,
    If I close the CMD, I will lose the connection, and I have to reconfigure it again.
    If I open APEX locally , I mean by using the shortcut "Get Started With Oracle Database 11g Express Edition" , Then I will lose the connection that uses the default port of the listener, that is 8080.
    After I configured the listener I got this message on the CMD
    -- listing properties --
    PropertyCheckInterval=60
    ValidateConnection=true
    MinLimit=1
    MaxLimit=10
    InitialLimit=3
    AbandonedConnectionTimeout=900
    MaxStatementsLimit=10
    InactivityTimeout=1800
    MaxConnectionReuseCount=1000
    APEX Listener version : 1.1.2.131.15.23
    APEX Listener server info: Grizzly/1.9.18-o
    May 21, 2011 5:14:41 PM com.sun.grizzly.Controller logVersion
    INFO: Starting Grizzly Framework 1.9.18-o - Sat May 21 17:14:41 GST 2011
    INFO: http://localhost:8080/apex started.
    Using JDBC driver: Oracle JDBC driver version: 11.2.0.2.0
    Regards,

    Hi,
    I'm not sure I got your question right, but I'll try to find some solution anyway.
    If I close the CMD, I will lose the connection, and I have to reconfigure it again.That's what happens when a shell is terminated - all associated processes will stop as well. However, if you have a apex-config.xml in your apex.home you shouldn't need to configure your APEX Listener each time your start it, but it would reuse an existing configuration.
    If I open APEX locally , I mean by using the shortcut "Get Started With Oracle Database 11g Express Edition" , Then I will lose the connection that uses the default port of the listener, that is 8080.Now, if you have XE running on the same (local) machine as you have your APEX Listener running in standalone mode, you probably have a port conflict: By default, both APEX Listener in standalone mode and the Embedded PL/SQL Gateway (EPG) use port 8080. The EPG is activated as web server for APEX in XE after a fresh installation, the APEX Listener would be an alternative in that case. You can either stop the EPG, or reconfigure any of the two web servers to use a different port, if you want to run them parallel.
    To change the port used by the APEX Listener in standalone mode, you simply add another parameter to the startup: -Dapex.port=8888 and you're done.
    To change the port used by the EPG, connect as sys and run the following
    EXEC DBMS_XDB.SETHTTPPORT(8888);
    COMMIT;If you want to disable the EPG, simply set the port to *0* .
    After I configured the listener I got this message on the CMDThat's what it should look like.
    No, since your topic is "lose the connection when closing the CMD", I assume you search for an alternative. You could run the APEX Listener as a Windows service, even in standalone mode. To do this, you create a batch file, e.g.
    %JAVA_HOME%\java -Dapex.home=D:\oracle\APEX_Listener\_home -Dapex.images=D:\oracle\apex_4_0_2\images -Dapex.port=8888 -jar D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\apex.war >>D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\my_apex_listener.log 2>&1Note that you have to set JAVA_HOME as system property or replace the call with the absolute path to your JDK or make sure the JDK is in your PATH variable.
    Of course, you can and should change the other directories as well to fit to your system.
    Next, create a Windows service, e.g. using [url https://iain.cx/src/nssm/]NSSM (free) or [url http://support.microsoft.com/kb/137890]SRVANY (MS, non-free), that starts your batch as a windows service.
    The command for creating that service using NSSM could look as follows
    nssm install APEX_Listener D:\oracle\APEX_Listener\apex_listener.1.1.2.131.15.23\startup.cmdYou can edit the service properties afterwards, e.g. change the start mode from "Automatic" to "On Demand".
    I hope this answers your question. If not, please point me into the right direction.
    Thanks,
    Udo

  • I lose wireless connectivity when I connect the nano to my PC

    I have a DSL modem connected by ethernet cable to a Linksys wireless router. My PC has USB linksys antenna. The wireless connection works fine except when I plug in the Nano, it takes about two seconds and I lose the connection to the router. If we are in itunes downloading it is suspended. If we are on the internet the next click and the Microsoft "you are not connected to the internet" page comes up. To reestablish the internet connection I have to remove the nano and reboot the PC. Needless to say this is very frustrating.
    If I reboot with the cable attached I get an error unable to run an ____.exe that I believe is the antenna setup because the linksys monitor stays gray in the startup box.
    I have tried to move the antenna to a different USB port on the PC with no luck. Everything else runs fine.
    Does anyone out there have any ideas/fixes? - Your assistance is greatly appreciated!

    thanks deggie for your answer.
    I had my ipod with autosync off ... I set it "manage like disk" .
    I try to recover the music with 2 programs: "ephod" and "copy trans" ..
    I can see all the songs listed, but can´t backup to disk or recover them......  
    I see than my ipod hasn´t the folder  "ipod_control" , which appears before I had this problem....
    Any idea ??? Thanks again.

  • New 6500 E709n loses wireless connection when it or laptop sleeps... & other problems!

    Just got this printer and am hoping we can get it to work because we really like it.  I believe we've done everything right - it is connected to PC via USB, and to laptop via wireless network.  Both computers are Dells running XP.  Our wireless router is a Linksys Wireless-G WRT54G.  We installed the disk on both.  Immediately after installing on the laptop by plugging in USB and then unplugging, we were able to get it to work.  We printed and scanned from both . . . UNTIL the printer went into power save mode.
    When it sleeps it loses all the network connections (but will still print from PC).  Even the icons disappear from the laptop after it sleeps.  The only way to get it to work with the laptop again is to start all over, plug in the laptop, enter the WPA key again, and so on.  Then it's finebut for just a short while.  Now, when I registered my protection plan, I was on the phone with a techie guy and asked him if it's normal to have to keep entering the key every time you want to print, and he actually said that maybe I shouldn't let the printer sleep - wow! I want to conserve energy, so I may even want to shut it off, okay, and I don't feel I should have to go through this rigamarole every time I want the darn thing to just be available to the network.  Furthermore, what's the sense of having to turn "Wireless Radio" on and off all the time???
    Anyway, there are other problems and the menus in the internal web browser is about as confusing as it can be.  Is the passphrase the same as a WPA key?  There's a passphrase in there which I did not enter, and I don't know what it is because it's been disguised with dots.  When I enter the WPA key on the front panel of the printer, it doesn't stick.  One thing I noticed in the instructions is to keep telephones away from it, so I moved ours (was right next to it) but it's still being ornery.
    In addition, the scan function only works from the software, not as a standalone if I use the front panel.  When using the button on the front panel, sometimes it sees the laptop, sometimes it doesn't, and then it starts to scan, but a menu pops up on the computer asking to update the buttons, and then nothing happens.
    Have we a clunker on our hands that should be returned, or is there a remedy?  All suggestions welcome!
    Message Edited by geoxena on 10-20-2009 10:56 PM
    Message Edited by geoxena on 10-20-2009 11:03 PM

    Let me answer the easy stuff first:
    Yes, the passphrase is the same as the WPA-PSK key.
    No, it's not normal to have to re-enter the wireless security key over and over again.  Politely tell our service agent that he is mistaken on this point.
    There's no sense in having to turn the radio on and off all the time to get the printer to remain on the network.
    When the printer goes into power-save mode, can you still access the printer's internal web page by browsing to it's IP address?  When the printer loses wireless connectivity, can you wake the printer by pressing any of the buttons on the front panel?
    I have a couple more questions:
    What WRT54G HW version do you have (it'll be on the bottom label of the router)?
    What version of FW does your router have?  You'll have to browse to the router's internal web page to find out.
    Finally, change the WPA-PSK group key renewal period to the largest value possible.  Tell if this affects the frequency of printer losing Wi-Fi connectivity?
    One more question.  After you have the printer connected to your wireless network and it's working, if you turn the printer off (via the power button), wait five seconds then unplug it then plug it back in and turn it on, does it connect to your network?
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

  • MacBook loses wireless connection when iPod touch connects to network

    hi
    ever since upgrading to 10.5.5. on my MacBook i've had the "intermittent network connection" problems that have been described and discussed (without any real solution from what i can see) in another thread.
    PROBLEM: every couple of minutes my MacBook loses connectivity to the network - the AirPort icon still says that i'm connected, albeit with one less bar than before, but i can't connect to anywhere, not even to the wireless router - and to re-establish a connection i need to switch off AirPort, switch it back on, it will then reconnect, and after two minutes or so i have to do it all over again because the network connection drops again.
    NOVEL OBSERVATION 1: reinstalling the 10.5.5. combo system updater helped somewhat. i used to get an error in system.log about there being too many state transitions on the wireless network and about network traffic reduction measures being taken to overcome this problem, but after reinstalling the 10.5.5. combo system updater this message never appears in the logs and I get kicked off only sometimes (see what i say in point 2 below)
    NOVEL OBSERVATION 2: now my MacBook will only lose its connection to the net if i switch on my iPod Touch and switch its wireless interface on. in fact, the only way to avoid the MacBook getting constantly disconnected is to make sure that the wireless interface on the Touch is switched off in the Touch's system preferences; if I just sleep the Touch (top button) without switching off its wireless network interface first in its System Preferences, then the MacBook will keep disconnecting even while the Touch is in sleep mode (presumably the Touch keeps polling the network or something, even while it's in sleep mode).
    DIAGNOSTIC NOTE 1: I have another wireless device (my Nokia E51, which has wifi capabilities) and if I connect it to the wireless interface then the MacBook's connection isn't dropped - i.e. the MacBook only loses its wireless connection when my iPod Touch connects to the wireless network.
    DIAGNOSTIC NOTE 2: I have upgraded my wireless router (before I had a Linksys WRT-54GC, now I have a Netgear WGR614v9) but that has made no difference.
    DIAGNOSTIC NOTE 3: I have also tried altering the router's settings (i have played around a_lot with this, trying every combination I could think of - e.g. staple down particular devices to particular ip addresses, use only 802.11g versus automatic b/g, etc) but that has made no difference either.
    RANT:
    The only thing that prevents these disconnections from occurring is to keep the iPod Touch's wireless switched off, which ***** because if I'm in the kitchen I can't have it switched on to monitor my email (yes, I've no life, i hang around waiting for emails), or if I go have a lie down and want to check out stuff on the net, or to browse the iTunes music store or whatever, then I know that my connecting my iPod Touch the computer will be disconnected.
    This obviously *****, right? And a lot of people are having wireless problems with their MacBooks, right? And these problems seem to have been around for over a year, right?
    So why hasn't Apple solved this problem yet? Or am I just being melodramatic?
    Your thoughts on any or all of the above, or flames if that's your preferred method of communicating, are invited. =)
    Cheers
    dr.colekat

    Having the same problem here. As a first time mac user, Apple has certainly made a bad first impression.
    For me, the issue seems to occur when transferring files between computers that are connected to the same access point (when transferring files from wired computers on the network there is no issue). My vista laptop and every laptop I have tried has worked perfectly fine with this access point so I am 100% convinced it is the mac. Basically when I copy the files, after about 100mb, I am unable to access anything on the local network or internet until I restart Airport. The weird thing is that even though I am unable to access anything, the airport utility says it is connected. I might also note that the wireless signal strength is full.
    If I can't get this figured out in a few days, this computer is going back to the store where it came from and I will officially label myself anti-mac. This type of issue is just unacceptable for something so main stream.

  • When my daughter connects to our home wifi she has to be within 5 feet of the modem, once she moves upstairs she loses wifi connection and then when choosing the network, it can't find our wifi network?

    When my daughter tries to connect to our home wifi, she has to be in the basement within 5 feet of our modem.  Once she comes upstairs she loses the connection.  All of our other devices connect to the wifi on all levels of our house, including her Dad who also got an iphone 4 and her ipod works as well as her brother's ipod and my blackberry.  I have tried resetting the network settings to no avail. I have already had our modem rebooted through our internet provider so I know the signal is good (as well as all other devices connect to wifi) I am losing sleep over this and she is quite frustrated so any help would be appreciated.  I'm starting to wonder if it's a defect in her phone???

    Is her iPhone in a case by any chance?  If so, remove the case and try again.  How does her iPhone work in free Wi-Fi locations?
    Try resetting the iPhone...
    Press and hold the Home and On/Off buttons simultaneously until you see the Apple logo, then release.  This may take up to 10 seconds.  This is the equivalent of a re-boot and you will not lose any data.
    If none of the above work take it to an Apple store or AASP for evaluation.  She will not be charged folr this and they will suggest a solution if there is a fault.

  • My ipad 1 loses wifi connections when it goes to sllep. have to go into settings to reconnect. Does this all the time. please help.

    my ipad 1 loses wifi connections when it goes to sleep. have to go into settings to reconnect. Does this all the time. please help.

    my ipad 1 loses wifi connections when it goes to sleep. have to go into settings to reconnect. Does this all the time. please help.

Maybe you are looking for