WRT54GS not getting Ip from WAN in any configuration

Able to configure router and connect it fine but will not pull and IP from provider or any other device on the WAN port. I think the WAN port is dead but not sure.
Have rebooted and reset to factory. WAN light is solid all the time and does not try to detect connection. LAN ports work fine and assign addresses.
Also have a wireless N router that does the same thing. Currently using a different brand since it seems the Linksys router keep dying on me.
Looking for suggestions for a fix if that is possible.

Connect a Single Cable from LAN Port to WAN port of the router ...
Check the Light status on both the ports ....
If getting lights .... the ports are working fine ...
Also if not light ... ports are daed ,.,....
Reset for ferw seconds.... & check if any difference is there or not ....

Similar Messages

HT1848 i formatted my computer and now i would like to sync my music from my iphone back to the computer, is there any way to do this? i don't want to loose my music. p.s. all my music that was on the computer was there privately, i did not get it from it

i formatted my computer and now i would like to sync my music from my iphone back to the computer, is there any way to do this? i don't want to loose my music. p.s. all my music that was on the computer was there privately, i did not get it from itunes.

See Recover your iTunes library from your iPod or iOS device.
tt2

TS5185 Hi After I have report a junk message I coudl not get Imessge from other iphone. and could not send any message in blue color but green which need to pay for.

Hi After I have report a junk message to 7726, I coudl not get Imessge from other iphones. and could not send any message in blue color but green which need to pay for. Does Apple blocked my imessage ? I have checked the setting. imessage is on.
Thanks,
J

Make sure that your date and time settings and time zone are accurate (Settings - General - Date and Time). Reset your phone to 'Set Automatically' and then try signing in again - this worked for me. My date/time settings were not automatic (candy crush cheats!!).

Excise rate and value is not getting defaulted from the purchase order

Hi all,
While capturing excise invoice , the excise rate and value is not getting defaulted from the purchase order and in Excise Item Tab BED,AED,ECS is Zero at both header as well as item level for only one material in STO process and if we are doing same process taking other material all things are coming perfectly and We are maintaining condition with respect to vendor,plant and material combination.Any input related to this will be helpfull and rewarded.
Regards
Vishal

Hi,
Follow STO Process for this;
1.Create a vendor for the company code of receiving plant, using account group: 0007 using T-Code XK01.
2. Assign this vendor to Delivering plant
Go to XK02 >Purchasing view>Extras>Add. Purchasing data>Plant
3. Create internal customer with the sales area of the vendor. Go To XD01
4. In pricing procedure determination relevant to STO, assign document Pricing Procedure and customer pricing procedure appropriate for STO to get the pricing in the invoice.
5. Maintain condition records for the relevant pricing condition.
6. Some more setting for STO: Go to MM> Purchasing > Purchase Order > Set up STO > define shipping data for plants > Go to Receiving plant >assign customer here & Supplying SA (for billing) to Receiving plant here
7. Go to MM > Purchasing > Purchase Order > Set up STO > define shipping data for plants > Go to Supplying plant and assign the sales area of receiving plant.
8. Go to MM > Purchasing > Purchase Order > Set up STO > assign delivery Type & Checking rule
Assign the delivery type to document type. In this case, Delivery type NLCC is assigned to Document type NB
9. Go to MM> Purchasing > Purchase Order > Set up STO > Assign document Type, One step Procedure, Under delivery tolerance
Assign the document type NB to supplying plant and receiving plant
10. After all settings, Create the STO using T-Code: ME21N and maintain pricing conditions of freight and Save.
11. In supplying plant Maintain condition record in sales using VK11 the same will flow in receiving plant when referring the OBD no during MIGO.
10. Create Delivery: VL10G
12. Picking, PGI: VL02N
13. Billing: VF01
Save the document and its done
14. J1IIN - Outgoing Excise Invoice
15. MIGO - Goods Receipt against outbound Delivery
16. J1IEX - Capture & Post Excise Invoice
Rgs

Iphone 5 not getting text from new numbers?

im on ios 7.0.4. Recently, ive been having the problem of not getting messages from new numbers. I receive all texts and calls from all current phone numbers ive ever had contact with. But for the past month, any new numbers that text me first, i do not receive them. But if i text and or call them first, it works fine. Which isnt always a convinence. They sent me screen shots of my number and their text; they all have different phones on different services.

Perk123, this is a text messaging mystery! I'm on the case. I recommend that delete all unwanted text messages on your device and power it off/on to soft reset it.
You will also need to advise your friend that has the AT&T iPhone to reset the network on their device. This can be done by accessing Settings >General >Reset >Reset Network.
Lastly your friend needs to verify if your contact has been set up to block calls and text messages from your mobile number. This option is located in Contacts >your contact> Block this caller.
Keep us posted.
LasinaH_VZW
Follow us on Twitter @VZWSupport

RFC problem: could not get functionname from XML requst (sic)

I'm developing an interface that attempts to call a receiver RFC on an SAP 4.6c system. It's a very small simple interface, and it's all working until it tries to call the RFC. The error is
Exception caught by adapter framework: error while processing message to remote system:com.sap.aii.af.rfc.core.client.RfcClientException: could not get functionname from XML requst: com.sap.aii.af.rfc.RfcAdapterException: failed to read funtionname from XML document: missing namespace declara
I've created an RFC channel, which is green in the adapter monitoring. The RFC imports without a problem, and appears in my interface mapping. My mapping program converts to the RFC message type (as evidenced in sxmb_moni. I have a receiver agreement referencing the interface mapping, which must be working as the mapping is called.
Could anyone point me to what else I could check? I saw a post about the same error message, where the respondent found something in the logs which helped them Could you expand on what you found, and in which log please? Any pointers as to which logging options I could switch on and check would be gratefully received.
Regards
Alan Graham

Thanks for the responses.
I set up a communications channel of type RFC, which is
showing green in the adapter monitor. If I deliberately
break it, eg by changing the password, the adapter shows
as red in the monitor. I assume therefore that the
adaptor settings are correct.
The XML going to the adapter looks correct AFAIK. My problem is that I don't know enough about the requied XML to know if what I'm seeing in the logs is sufficient. In SXMB_MONI, in the 'call adapter' section of a failed message, the outbound binding includes
<SAP:ToInterfaceNamespace>urn:sap-com:document:sap:rfc:functions</SAP:ToInterfaceNamespace>/code]
Also, the interface determination SOAP header, in the MAIN section includes
[code]<SAP:Receiver>
<SAP:Party agency="" scheme="" />
<SAP:Service>D04</SAP:Service>
<SAP:Interface namespace="urn:sap-com:document:sap:rfc:functions">Z_MPU_3PSCE_FREIGHT_UPLOAD</SAP:Interface>
</SAP:Receiver>
These are the correct values for the RFC name and the namespace, AFAIK.
I'm using an interface mapping (which uses and ABAP class as the mapping program) which references the interface of the RFC. The logs tell me this works, ie, the class is called and the resulting XML appears in the payload of the response.
Alan

Mails not getting sent from Receiver Mail Channel

Hi ALL
I have a File to mail scenario , I see chakred flag in SXMB_MONI ..but mail are not getting triggred from the Receiver mail adapter..
I gave the URL like this smtp://sxd123.abc.com
and the respective E-mail ID's
I dont see any message in the communication channel monitering also ..wht could be the reson.. ?
Thanks
Souz

Hi Dominic,
Since you are not seeing any entry in the communication channel (receiver), I think there is a problem with your configuration. Check whether you have used the correct channel (of type MAIL) in the receiver agreement.
Regards
Suraj

Standard PO workflow giving error due to Release coe is not getting passed from event

Hi Team,
I am getting the below error while processing the Standard workflow for PO.
I think its due to the Release code is not getting passed from Event to workflow.
Can you please sugest from where the release code is getting fetched before triggering the event.
Error processing following event linkage:
BUS2012 RELEASESTEPCREATED WS20000075
Following error occurred:
SWF_RUN 594
Message text:
Import container contains errors (are any obligatory elements missing?)
Event container appended as attachment.
Event linkage not changed.
Event stored temporarily.
Events can be redelivered via event queue
administration (transaction SWEQADM)

Hi
Please check threads, response by Fernando Carames, ( Jul 19, 2007 2:37 PM): http://scn.sap.com/thread/483005
Or by Trevor Ticehurst on Oct 9, 2008 3:39 PM at: http://scn.sap.com/thread/1080411
OR
http://www.sapfans.com/forums/viewtopic.php?f=26&t=297786
All these mention certian notes which may be helpful.
However, it is important to first ensure that the release startegy is configured and working properly (check with your MM con)
regards,
Modak

PO is not getting released from SRM

Dear Experts,
I am configuring SRM-SUS Scenario on SRM 7.0. I have set up all SRM, XI and SUS cofiguration.
(SRM - SHDCLNT901, XI - XHDCLNT500, SUS- SHDCLNT951)
Shopping Cart and PO is creating fine but PO is not tranferring from SRM to SUS.
when i checked SXMB_MONI in SRM, there is no messeges showing there. It means PO is not getting released from SRM.
Kindly let me know is there any t-code for enable communication between SRM and SUS?
I have correctly configured XI and also transferred vendors from SRM to SUS through SupplierPortalTradingPartner_CreateOrChange_Out messege type but
PurchaseOrderRequest_Out for PO transfer is not getting triggered in sxmb_moni in SRM.
Thanks in advance.
Regards,
Pawan Keshwani

Hi,
Thanks for your reply.
I have configured Application Control Workflow correctly ( I am using Workflow without approvals for PO (BUS2201))
And in Rz20, I am getting below messege ("SHD : MTE class BBP_PO , Client 901 : No MTEs currently available*) for PO in Rz20 given below path
(CCMS monitor sets -> SAP (CEN) EnterpriseBuyer Monitors -> Purchase Order)
I am configured ESOA Architecture in XI for SRM-SUS , and my root issue is " I am not able to generate XML messeges in SRM".
Not getting any messege in SXMB_MONI in SRM.
Regards,
Pawan Keshwani

Data not getting transffered from SRM system to BW

Hi All,
We have an issue where in the data is not getting transferred from SRM to BW. If i see in RSA 3 of SRM system, the datasource is pulling around 3000 records and in WE02, the idoc is generated and passed without any errors.
Whereas in BW the idoc is coming with code 8 and no data is getting transferred to BW.
What can be the probable reasons for this mismatch ??
Thanks
Abhi

Hi Abhi,
After an upgrade, i would go for following checks
1. Check the Data Source on CRM side and check if it is Active.
2. With Upgrade, usually DataSources become inactive and also, pls check if any required fields are hidden in the data source before you activate.
3. After unhiding required fields, i would activate the Data Source and Replicate the Data Source on BI Side.
4. Now I would delete the failed request by forcing its status to RED in RSMO and then go for the load.
Let me know if it worked.

Validity end date is not getting copied from inquiry to quotation.

Hi Friends,
While creating quotation the validity end date is not getting copied from inquiry to quotation.
What setting needs to be done, pl suggest.
Regards,
Hari.

Sreehari,
i dont find any logic of having Same validity date for Quotation and Inquiry....
the simple reason is explained by example: Say you have created Inquiry on 1st november and end date is 15th novembr. Customer comes to you on 14th november and asked for Quotation, and if you refer quotation on that day that means its only applicable for one day, which generally wont be the case.
There is no option for copying the validity dates from Inquiry to Quotation as per standard. If you want, create routine, place it in copy control.
Thanks,
raja

Profit Center not getting copied from WBS master data to settlement rule

Hello,
I am facing issues during settlement to G/L. From FI side we have set up some validations that the FI postings shld always carry a Profit Ctr. Now when I am doing settlement to B/S account, the profit ctr from WBS master data gets copied to settlement details and hence on FI posting (Credit line).
However when I am trying to settle to Expenxse/P&L account this is not happening. The profit Ctr is not getting copied from WBS master data to Settlement details and hence the settlement is not going thru. The profit derived is a dummy profit ctr and not the one on WBS master data.
I have posted this query on FI forum too but no satisfactory answers.
Pls let me know, what is the system behaviour....will the prof ctr on WBS master data gets copied on settlement rule details automatically ?
Sarang

Which exit do I use in OPSN? any thts or some exit in FI?
I am on ECC-6.0...
One thing to mention, the prof ctr is getting copied to settlement rules for Balance sheet account but not for P&L.This is more confusing...
Sarang

L2L issue, the tunnel does not getting up from one direction

Hello,
We have configure a L2L vpn between Asa and 1841 router. We are facing this issue.
The tunnel is not getting up from the 1841 site never. When we are trying to generate traffic from the ASA site the tunnel is up and we can see decryps and encryps packets.
Router 1841 Config:
crypto isakmp policy 100
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key * address 213.249.XX.XX
crypto ipsec transform-set XXXXX esp-3des esp-md5-hmac
crypto map EKO_BG 100 ipsec-isakmp
set peer 213.249.x.x
set security-association lifetime seconds 28800
set transform-set XXXXX
set pfs group2
match address 111
interface FastEthernet0/0.2
encapsulation dot1Q 3338
ip address 212.200.30.130 255.255.255.252
ip nat outside
ip virtual-reassembly
crypto map XXXXX
ip nat pool nat_pool 93.87.XX.XX 93.87.XX.XX prefix-length 29
ip nat inside source list 101 pool nat_pool overload
ip nat inside source static 10.70.2.10 93.87.18.161
ip nat inside source static 10.70.25.10 93.87.18.162
ip nat inside source static 10.70.36.5 93.87.18.163
ip nat inside source static 10.70.39.10 93.87.18.164
ip nat inside source static 10.70.5.10 93.87.18.165
access-list 101 deny ip 10.70.200.0 0.0.0.255 any
access-list 101 permit ip 10.70.0.0 0.0.255.255 any
access-list 111 permit ip 10.70.200.0 0.0.0.255 172.40.10.100 0.0.0.3
Asa Config:
access-list inside_nat0_outbound extended permit ip 172.40.10.100 255.255.255.252 10.70.200.0 255.255.255.0
access-list outside_cryptomap_320 remark xxxxxxx
access-list outside_cryptomap_320 extended permit ip 172.40.10.100 255.255.255.252 10.70.200.0 255.255.255.0
access-list inside_pnat_outbound_V5 extended permit ip host 10.8.x.x 10.70.200.0 255.255.255.0
pager lines 24
nat (inside) 9 access-list inside_pnat_outbound_V5
crypto ipsec transform-set xxxxx esp-3des esp-md5-hmac
crypto map mymap 150 match address
crypto map mymap 150 set pfs
crypto map mymap 150 set peer XXXXXX
crypto map mymap 150 set transform-set XXX
crypto map mymap 150 set security-association lifetime seconds 28800
crypto map mymap 150 set security-association lifetime kilobytes 10000
crypto map mymap 320 match address outside_cryptomap_320
crypto map mymap 320 set pfs
crypto map mymap 320 set peer XXXXX
crypto map mymap 320 set transform-set XXXXX
crypto map mymap 320 set security-association lifetime seconds 28800
crypto map mymap 320 set security-association lifetime kilobytes 4608000
crypto map mymap 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map mymap interface outside
isakmp policy 150 authentication pre-share
isakmp policy 150 encryption 3des
isakmp policy 150 hash md5
isakmp policy 150 group 2
tunnel-group 212.200.x.x type ipsec-l2l
tunnel-group 212.200.x.x ipsec-attributes
pre-shared-key *
Please advise.
Thank you.

hello Ashley,
thank you for this info. Now from the router site the tunneling is getting up and I can see packets but althought the tunnel is up it can not make telnet to our server (172.40.10.100) on a specific port.
We from ASA site can ping router Site and make telnet.
Any ideas???
Thank you all from your answers!

EA2700 not getting IP from modem

Just received this new EA2700 router the other day, have noticed this problem has been reported a few times in other forums.
Went from a WRT54G connected to a DLINK 202 modem, actually they had no problem, I was just upgrading, when swapping out the router, I noticed it took a very long time with many reboots of modem and router to get an IP, which is set for DHCP from Comcast. The old combo would get an IP within a minute of a reboot. So, just to complete my upgrade, I bought a Motorola 6141 modem, had it set with new MAC at Comcast, same problem with router trying to get an IP.
I did find if you reboot the modem by itself, last, while router is up, the router will get an IP within a few minutes. But, if they are both rebooted together or if the router is rebooted by itself, it will not grab an IP. I have not seen a solution for this "known" problem in all the forums I have read, I have seen quite a few people become very frustrated and just give up on their EA2700 or buy something else.....firmware is latest, I've tried MTU at 1365, IPV6 off/on, resetting, running install app, same problem. So unless someone has the real answer for this, I could be one of those swapping this for another model or brand, I'm afraid.

Khan,
The problem of users not getting IP from the DHCP usually happens when 'spanning-tree portfast' is not enabled on access ports. PCs don't wait long enough for DHCP responses and time out.
Can you make sure all the access ports, to which the users are connected to, have spanning tree portfast enabled.
HTH,
Sundar

ATV2 not getting IP from ethernet

I have an ATV2 connected to a Airport Extreme via ethernet.
When I start up the ATV2, it is not getting a local IP via ethernat from the Airport. Rather the 169.254.xxx.xxx
I have tried all the suggestions i've read in the forums relating to 169.254 including, Manually configuring the TCP/IP.
In all cases, on boot the ATV will not grab a local IP; however, If I unplug the ethernet cable for 30 seconds and plug it back in, the local IP gets assigned and everything works fine. ie. Streaming movies, music, netflix etc.
If i restart the ATV once everything is working. Same thing happens.
Does anyone have any ideas as to why this happnes?
Thanks in Advance

Khan,
The problem of users not getting IP from the DHCP usually happens when 'spanning-tree portfast' is not enabled on access ports. PCs don't wait long enough for DHCP responses and time out.
Can you make sure all the access ports, to which the users are connected to, have spanning tree portfast enabled.
HTH,
Sundar

WRT54GS not getting Ip from WAN in any configuration

Similar Messages

Maybe you are looking for