WRT54GS Not saving port forwarding info.

I gave up on an older router, and had the wrt54gs sitting in my closet. I had to set it up for the PSN and COD4, but everytime I enter the port forwarding info, it says its saved, but erases it.
The info is:
TCP 80
TCP 443
TCP 5223
UDP 3478 - 3479
UDP 3658
All enabled on PS3s IP
Click SAVE SETTINGS
It opens a black window that says settings saved
I click OK
and everything has been erased.
Im on firmware 7.50.2.
Ive tried both firefox 3 and internet explorer. (ff3 error console gave me no errors)
DMZ is enabled for my PS3.
Ive tried both a wired and wireless connection.
I can use my PS3s browser (if that matters)
Any suggestions?

You need to Upgrade the Firmware on your router...Download the Firmware from here , Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router and do the port forwarding and check if it saves the settings...

Similar Messages

Linksys E1200 Router not saving Port Forwarding changes

Hi!
I am currently attempting to port forward on my Linksys E1200 Router and am not succeeding in saving my settings. I am attempting to open port 25565 though both Single Port Forwarding and Port Range Forwarding, and whenever I click the "save settings" button, I receive a full window message stating that my changes have been saved. Upon clicking this, I return to the previous screen whereupon my changes have been erased and my port has not been forwarded. Can anyone assist me with this? I've searched for hours through forums and tech help websites, but I can't find anyone else with this issue.
Issue:
Linksys E1200 Router not saving Port Forwarding changes.
I have tried:
-Restarting the Modem
-Restarting the browser
-Restarting the computer
-Tried to Port Forward through both the Single and Ranged Port Forwarding

Hi there. You can try another browser or a different computer. If it is the same thing, upgrade the firmware of the router. You can refer to this link on how to http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=0a6881b90224439b92c8d8f19ca42e5d_21511.xml&pid=80&...

E3200 not saving port forwarding settings

I have tried numerious times to set my port forwarding settings. Everytime I setup and fill in the appropiate ports and hit the save button my setting are lost. I go back into the port forwarding setting page and literally after a fews secondsof inputting the ports and nothing is there and everything is zeroed out . Has anyone experienced this problem. Do I have to set my ip address to static before I can put my port forwarding settings in.

Yes to all.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

WRT610N V1 will not allow port forwarding via HP Mediasmart Server

I have the WRT620N router and an HP MediaSmart server connected to it. My source is a cable modem. WHen I try to set up the server for remote access, the router is not found. I am continually getting "Port Forwarding failed" errors from the server. I also have several iPhone apps used to control devices on the network (DVR, BluRay player,etc) that will not connect. (These worked before I changed to this router.)
I have verified that the UPnP is enabled.
I have been struggling with this issue for several months and have not had any luck getting help from the forums, but will tryi again.
Any help would be appreciated.
Thanks,
Joel WZ
Thanks,
Joel WZ

Did you tried to enable Remote Management Access on the router setup page?
If no, then Enable Remote Management Access under Administration tab and then check.

WRT54G v.3 Port Forwarding Reset Problem

I have a Linksys WRT54G and I've had it for well over 3 years. I've been using another Wired router as a DHCP server and only used the wireless router for wireless access.
But recently, I took the wired router away and began using the WRT54G. I set up everything correctly including Port Forwarding, but the strange thing is that whenever I reboot my computer, the port forwarding service stops. If I enable it, disable it or do anything else, it still won't work.
The only way to fix this problem is to 'Reset Factory Settings' every time, but it gets really frustrating doing it every day. Has anyone else had this issue? P.S. - I have the latest firmware.
Message Edited by DaLink on 02-07-2008 03:30 PM

Checking back after 1 month, I still have this problem, no workaround found. Can anyone lend a hand?

WRT54G. DMZ/port forwarding no longer works?

I have a computer hosting an IIS web site / other services (to the internet) that had been working for a long time. Now, no matter what I do, I can not get it to work anymore, it's driving me crazy. I can access the services on my local network using 192.168.1.x, just not from the internet IP. The computer's IP is configured as the DMZ, I also tried specifically port forwarding instead. Windows firewall has exceptions for the ports, and I even tried turning it off temporarily, no luck. I am running out of ideas. Can anyone help? Any ideas?

I've also got this problem. Though I swore it used to work with 4.21.1 initially. Regardless, this is weak & annoying so hopefully I can get my hands on 4.20.7 & downgrade.
Also, in the last several months I've had to reflash & reprogram the device from scratch to "unbrick" it ... basically it would stop forwarding packets between the inside & outside interfaces. Meaning I could ping/manage it from the internet but not the LAN or vice versa. I assumed the issue was a corrupt configuration sine each time I had to rebuild my configuration from scratch after reflashing the firmware. Just restoring the configuration from a backup left things in the same unusable state as before.
Hopefully Linksco will address these issues and get rid of this wonky firmware version in favor of a stable one.

DW 8 Not Saving FTP Login Info

From session to session, Dreamweaver site setup is not saving
the ftp username and password info for all of the sites I manage -
a real pain in the ... Any thoughs as to what's going on or is
anyone else experiencing this problem?
Thanks
Rod Parker

That question is also asked and answered frequently - what is
the name of
your hard drive? Does it begin with any special characters?
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"jeffcoproductions" <[email protected]>
wrote in message
news:ee01tr$a53$[email protected]..
> This problem seems to be asked and answered an awful
lot, but no one seems
> to
> be talking about the problem occuring in OS-X (10.4.7).
Surely I'm not the
> only
> one. MX still works, but in 8, everytime I close
Dreamweaver and reopen,
> all of
> the logins and passwords are gone. I have no Internet
Explorer 7 to
> uninstall,
> and I've upgraded to 8.0.2. Anyone have any suggestions
for the Mac users?
>

HT202667 Unable to Update My apple ID - Not Saving My New Info

In "Manage My Apple ID", the web site is not saving my new email. I am attempting to change the primary ID to a new, valid Gmail and every time I click save it reverts back to the original Apple ID. This is very frustrating! Could anyone please help?

Im sorta having the same issue. I logged on to Icloud.com on my desktop. I was asked to update your apple ID with a verification code sent to my email. I checked the email and this is what it said.
Your Apple ID was used to sign in to iCloud via a web browser.
Date and Time: March 13, 2015, 7:19 AM PDT
Browser: Chrome
Operating System: Windows
If the information above looks familiar, you can disregard this email.
If you have not signed in to iCloud recently and believe someone may have accessed your account, go to My Apple ID (https://appleid.apple.com) and change your password as soon as possible.
Apple Support
As you can see there is no code and i cannot access my Icloud account until i enter a verification code, i have requested three different times for a new code and i still have not received an email.

Hooking "SlingBox" to WRT54gs...port forwarding...

I have had wireless network for about two years and have had no problems...but I need to hook a ling Box Pro" to it so my nephew in Yemen can access a Tivo I have hooked to the net work..
Sling box tells me I have to do "port forwarding" I have serched for "sling box" and "port forwarding" on this site and have got no returns...
Does anybody have any idea how I can do this hook up so it will broadcast remotely over the internet???
Any help will be appreciated,
Thanks,
Hefs

hi Hefs, try following steps...
first off you need to assign a static IP address on slingbox according to DHCP server of the router, if router is running on 192.168.1.1, sling box should have 192.168.1.10 subnetmask 255.255.255.0 and default gateway 192.168.1.1...logon to router's setup page, open I.E. and in the address bar type 192.168.1.1 it would ask for username and password, put "admin" (default password) as a password without any username...try reducing MTU to 1365, click on "applications and gaming" >> port range forwarding >> under the application put "slingbox" start port should be 5001 and end port is 5001, protocol should be both and put the IP address of slingbox which you've assigned, check the check box and save the settings...also make sure that you have latest firmware installed on the router...let me know the results.

Dreamweaver not saving sites login info

Dreamweaver 8 is not saving my site logins and passwords,
regardless of whether or not the "save" checkbox is enabled.
This is on XP 64bit, I did not have this problem on my
previous machine running the same version of Dreamweaver and
XP64.

Search this for for "It's posted a million times - uninstall
IE7 or update
to DW 8.0.2". I'm sure you'll find your answer in one of
them.... 8)
Murray --- ICQ 71997575
Adobe Community Expert
(If you *MUST* email me, don't LAUGH when you do so!)
==================
http://www.dreamweavermx-templates.com
- Template Triage!
http://www.projectseven.com/go
- DW FAQs, Tutorials & Resources
http://www.dwfaq.com - DW FAQs,
Tutorials & Resources
http://www.macromedia.com/support/search/
- Macromedia (MM) Technotes
==================
"dynedain" <[email protected]> wrote in
message
news:ejahrc$svp$[email protected]..
> Dreamweaver 8 is not saving my site logins and
passwords, regardless of
> whether
> or not the "save" checkbox is enabled.
>
> This is on XP 64bit, I did not have this problem on my
previous machine
> running the same version of Dreamweaver and XP64.
>

WRT54GS Wireless Router, Port Forwarding, LED Display

Hello everyone. I'm using a Linksys router on a network like this:
I have comcast cable internet using the motorola cable modem that is supplied by them. This is connected to my Linksys WRT54GS which is then connected to my desktop PC and laptop as well as a Troy500 print server.
The Troy500 print server is connected to an LED display with a serial cable. The desktop PC has a logitech webcam on it.
I was able to setup the webcam to be viewed online, I had to use the web configurator in the router to forward ports 8000 and 8080 to the desktop PC which has a local IP address of 192.168.1.2. This works fine.
My Laptop has an address of 192.168.1.3 and I am able to LOCALLY communicate to the Troy and display items on the LED using the laptop AND my desktop. BUT when I forward ANY outside port to the Troy to try and get this to work remotely through the router I get a communication error.
Someone suggested that Comcast may be filtering various ports so I tried over 10 different port numbers and still get the same error.
I then tried to get help from a tech guy I know from florida and he was unable to get to the router through the remote management feature, we used port 9000, 7000, and port 9999, nothing worked to get him in. ALSO he was unable to ping my outside IP.
BUT I am able to get online, and I'm able to see all the devices on the router, AND he's able to see the webcam which is using ports 8000 and 8080 to communicate outside.
Any suggestions?
Oh, ALSO, nothing on this network is wireless except for the laptop, and this functions just the same when I plug CAT5 into it, it makes no difference.
Message Edited by Matusky on 09-11-2007 02:16 PM

first off , make sure that the router has the latest firmware...on the router ui , under the "security" tab , disable "block anonymous internet request" ... check whether these changes make any difference....

WRT54G ver 6 Port forwarding question

Howdy... I just purchased the WRT54G ver 6 router to replace my old wired one that was fried after losing power one night... plugged into a $60 surge protector... but I digress... I have 2 PCs plugged into this router... neither are wireless. I host a website and so I setup the router to forward port 80 to the webserver... The loading of images has become incredibly slow. Probably 3 to 4 Xs as slow as the old router... If I plug my cable modem into the pc direct it seems fine, so I dont see a bandwidth issue or upload problem... Seems to be at the router and more specific where the router is forwarding the request. Has anyone run into this? Are there settings on the router somewhere that I can tweak?

Try to lower your MTU settings.
"When you have eliminated the impossible, whatever remains, however improbable, must be the truth."

Not saving log on info

I reinstalled Dreamweaver on a new laptop and it won't save
the log on and password info for sites. I've downloaded the 8.02
update, but can't figure out the workaround for not having the CDs.
When i try to run the setup, it recognizes that Dreamweaver is
installed and wants to repair and isn't giving me the option to
browse as it states in the instructions. Is there any other way I
can access the file needed for the workaround?

> I had to install Dreamweaver on a new laptop and it
won't save log on and
> password information, even if I check the Save box.
Anyone have a suggestion
> for me please?
Is it version 8?
know issue of conflict with IE7.
go to adobe site and get the 8.02 update installer.
Alan
Adobe Community Expert, dreamweaver
http://www.adobe.com/communities/experts/

WRT54G not saving changes

I have a WRT54G version 6 router. The router had been working fine but then stopped allowing I-Net access. The router was reset and the firmware was updated. Still no access.
Now I'm not able to make any configuration changes as well. When a change is a made and then the "apply" button is clicked, the screen blanks to white and displays several "<" symbols in a line in the upper left corner. Then the router becomes completely unresponsive. Press the reset button or power cycle the router and try again to make configuration changes and the same "<" symbols appear.
At this point I'm at a loss.

Possibly the firmware is gone bad ....
Disable all firewall on the computer & upgrade the firmware ...
Once upgraded ...reset & reconfigure the router ....

Actions not saving all printer info

I have a large poster printer and I have about 6 different size posters that I print regularly. Each poster size has a bunch of differnt print settings (which roll of paper to use, where to position the poster, size of the image..). It seems when I save a action of me printing a poster not ALL of this information is saved from the print settings.
How can I completely automate this? I want to be able to press a button labeled "print 36x36" and it will print the image at the right size using the right paper in the right location on the paper. Any ideas? Thanks everyone!

Hi. Because the forum you originally posted in is for beginners trying to learn the basics of Photoshop, I'm moving your question to the Photoshop General Discussion forum.

WRT54GS Not saving port forwarding info.

Similar Messages

Maybe you are looking for