WRT54GS slamming Cable modem with Packets

Question

I'm having trouble with my WRT54GS locking up my Cable Modem. TWC says its slamming the cable modem with too many packets. Is there any way to check this on my end? Full story below.
A little about my set up. I have Time Warner Cable business class Roadrunner service. 5 Static IPs. 4 being used at the moment. The Cable modem has a 4 port switch built in. Port 1 has a month or so old WRT54GS router v7 latest firmware (Gateway mode, Channel 6). Port 2 goes to my Sonicwall Barracuda them my internal network which also has WRT54GS router v7 latest firmware (Router mode, Channel 1). Both routers are sitting next to each other. Ports 3 & 4 have a Vonage Router hooked to each of them.
I started having trouble April 5 with the Internet being down that morning, then that night and falling morning. I power cycled the Cable modem to restore service. Called Time Warner Cable after the third reset. They told me that didn't see anything wrong from their end and I should call them when it is down. I did this and they said they would send someone out the next morning Friday. They came out on Friday morning and Checked cable which the tech said was fine so he replaced the Cable modem around 11:30. Fifteen minutes after he left the internet went down. I called TWC again. They did diagnostics on the cable modem from their end and saw that whatever was hooked up to port 1 was sent out 400 packets/sec. I think they said the cable modem could only handle 300. Port 1 is connect a WRT54GS v7 (latest firmware). We are using it for our Blackberries from Cincinnati Bell for WIFI and UMA service (like T-Mobiles @Home service) for VoWiFi. I turned off all the phones but the router was still slamming the modem with packets. I turned off the WiFi just in case someone hacked our WPA2 key. Still slamming the router with packets with only my laptop hardwired to it for setting up the router. I turned off the router and the modem wasn't getting hammered anymore. Port 2 which is my internal network was only up to 150 after open a lot of TV shows. Ports 3 & 4 nothing. I disconnected the WRT54GS hooked to Port 1.
15 minutes after I got off the phone with TWC internet goes down. They send out a tech on Saturday to check the line again. he sees a slight problem on the line but it should not be causing a problem which the first guy might have thought. But since I am having trouble he goes outside and checks the connections. He finds loose connection and a bad line cap (blocking cable TV). He fixes the connections and replaced the line cap. He comes back inside and rechecks the line. Everything is great no more fluxation of signal or packet loss. I hook the WRT54GS back but it still takes down the modem. So I figure that it's just bad. So I take the WRT54GS from my internal network and set it up to match the one for the Blackberries it's replace. I install a WAP54G on the internal network in it's place. I can't get my Blackberry to get a UMA connection and doing Google searched find this page
http://www.blackberryfaq.com/wiki/index.php/Linksys_Router_Tips
I set up my router and Assess point with the setting from the above except the channel setting leaving them on channel 6 & 1 so they don't interfere with each other. Set: Fragment Threshold : 2304 (256-2346), RTS Threshold : 2304 (0-2347) and Beacon Interval : 50 (20-1024 ms). I also Enable WMM QOS. My phone connects and internet seems to be staying up Saturday Evening. I come to work Sunday afternoon and Internet is still up. I check my phone I have UMA signal and everything is right with the world. 20 minutes later internet goes down. I unplug the WRT54GS and power cycle the cable modem. I am now waiting to see it the internet will stay up without any WRT54GS hooked up.
I have not had a problem before and both Linksys are not even 6 months old. I have read review were people have had trouble with the WRT54GS. Were some people have no trouble will other all kinds of trouble.

Answer 1

As you said cable connected to the pc is working fine!!...connect modem to the router WRT54GS...reset the router once (30 secs) in such a way that Power light on the router is blinking...power cycle complete network i.e., unplug modem & router power cable for 30 secs...plug in modem power cable once lights are solid green plug in the power cable to the router...its important that after upgrading firmware resetting the router is important...so try this & it should deifnately work.Do the wireless & advanced wireless settings as router is currently in default settings.
Also, you want to connect your access point WAP54G to the router & open the setup page of WAP54G using 192.168.1.245 do the wireless settings & try connecting to the wireless router & then check....should work.