WRT54GS suddenly stopped working

My WRT54GS Linksys wireless router suddenly stopped working. It is not an Internet problem because if I disconnect my router the Internet will start working again. I am connected thru a DSL connection. My router's power light will not stop flashing but all the other necessary lights are on. Any help pls...
Message Edited by nova_flush on 04-18-200702:30 PM

If the Power light is flashing thn thr is 100% problem with router. Power light should be solid green and other lights can be flickering.
Try to change power cord or reset the router for 30 sec and unplug pwer cord and plug back after 10 sec.
Remember powerlight should become solid green.
If not contact tech support bcz it may have gone bad and u will need replacement,
so contact as soon as possible before u run out of warranty period of the router.

Similar Messages

My WRT54G suddenly stopped working please help.

Hi, i recently configured the security of the router, and then when i pressed the auto connect on the router it can no longer send a wireless signal... i tried to press the RESET button on the back, it should return it to the factory setting right? but when i connected it it wont give me good ip addresses it says limited or no connectivity, even if i manual set the ip. then try to access the home page it would not work.
i have some ideas how to fix this but i dont know if it is possible or not. :
1.) reset the router from a computer without accessing the page.
2.) go to a service center (if there is an available in the philippines...)
3.) overriding the firmware without accessing the page
please help, or else i would need to spend another 40-50$ for a new router T_T
i also tried to download the easylink firmware, or the easlink connect
but i get a 550 error when accessing the page, the online chat is no help either, they say i am on first queue but no one is answering :/
ver: WRT54G ver7
Message Edited by Shinigami_V on 04-23-2009 07:19 PM

Hard reset your router for a minute...
Press and hold the reset button for 1 minute...Release the reset button...Unplug the power cable from your router, wait for 1 minute and re-connect the power cable...Also make sure that your computer is set to obtain IP automatically, disable any firewalls, security softwares on the computer before trying to access the setup page...Now check if you can access your router set-up...
Click Start >> All Programs >> Accessories >> Command Prompt...A black box will appear(Command Prompt)...In the Command Prompt window type ipconfig and press 'Enter'...Look for Ethernet Adapter Local Area Connection IP Address , Subnet Mask and Default Gateway...IP Address should be 192.168.1.x, Subnet Mask : 255.255.255.0, Default Gateway : 192.168.1.1...
If you get the above mentioned ip address and gateway then you should be able to re-configure your router...If you get an IP Address of 169.254, then reset the router again...If still you don't get the above mentione ip address and gateway then you should give a static ip address on the computer...
Click on the Start button >>> Settings >>> Control Panel >>>Network Connections- Right click on the icon for Local area connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the following IP address'- Provide IP Address - 192.168.1.5, Subnet Mask - 255.255.255.0, Default Gateway - 192.168.1.1...Click on Ok button to Save and Click on "Close" on main Properties window...Now try to ping the Default Gateway, type ping 192.168.1.1 and press enter, see if you get 4 replies...If it does not then try to diable and security softwares/firewalls on your computer and try to ping it again, you should get 4 replies...
If you get the set-up page then you can configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

HELP! Wireless Router [WRT54G] Suddenly Stopped Working

Hey guys, so over the past 2 weeks i cancelled a previous dsl subscription and i am now with AT&T my activation date was today and at first i wasnt able to connect to the net with my new modem... after chatting with tech suppport they made me login to the modems IP address to configure an email setting which somehow solved my issue i can browse the net perfectly when my macbook is directly connected to the modem with the ethernet cable but when i try to connect the ethernet cable to my linksys wireless router (which worked perfectly fine with the last modem ..) i cant seem to browse the net is there some kind of IP config that i have to do? i dont think the connection itself is faulty since i can successfully log on to the linksys wireless router's ip address and i can also see that connection is at full capacity in the wireless airport connection icon on the top of my window...but when i try to surf the net using the wireless conneciton it kind of just stands still and the page doesnt connect/load... can anyone give me some help pls? thakns

I'm having the same problem today. I've been using this router for a couple of years with no problem. Today the power went out, and now my router can't find the internet. I can connect to the internet if I just plug the modem into my computer, and I can connect my my router wirelessly and get into the setup menus, but the router and modem won't talk to each other. Is there any chance the ethernet jacks on the router fried somehow? When I plug my computer into the router with an ethernet cable none of the 1-4 lights comes on no matter which one I plug into. Is that because they only come on when there is an internet connection, or is there something wrong with them maybe?

Photoshop CS4 64bit suddenly stop working

Having problems with Photoshop CS4 64bit version stop running for me giving me this error message with these details:
Problem signature:
Problem Event Name:    APPCRASH
Application Name:    Photoshop.exe
Application Version:    11.0.1.0
Application Timestamp:    499bfd16
Fault Module Name:    StackHash_0b5f
Fault Module Version:    6.1.7600.16385
Fault Module Timestamp:    4a5be02b
Exception Code:    c0000374
Exception Offset:    00000000000c6cd2
OS Version:    6.1.7600.2.0.0.256.1
Locale ID:    4105
Additional Information 1:    0b5f
Additional Information 2:    0b5f2ed00a0371f4956b3b2a23be79e0
Additional Information 3:    a274
Additional Information 4:    a2747fd43e73092b139f32555a88633d
It seems when i do something simple as typing text, it'll stop working and give me a "Adobe Photoshop suddenly stop working". My CS4 32bit version seems to working fine with whatever i'm working on. I'm running a fresh install of Windows 7 64bit Ultimate on a new computer Intel quad core with 4gig of ram if that helps. Sorry if this have been asked before but i couldn't find anything on these forums. Thanks in advance.

i deleted the prefs file and now i can open photoshop. but it seems as if it crashes if i open ANY file with ANY text, no matter what the font is.

My usb that i have been using on my computer for a while suddenly stopped working, but is still glowing and letting me know that it is connected, but not showing up in disk utility

my usb that i have been using on my computer for a while suddenly stopped working, but is still glowing and letting me know that it is connected, but not showing up in disk utility

Either the physical drive or the enclosure electronics has failed. The light you are seeing is powered by the USB connection, the power, electricity, all USB ports put out. That doesn't mean the actual physical hard drive or the USB to SATA bus electronics are working properly. If it doesn't show in Disk Utility then it is DEAD.
Most of the time it is the enclosures electronics that fail. Removing the physical drive from the enclosure and put it in another enclosure or using a SATA to USB adapter, one that has it's own AC power supply, might allow you to get the files off the drive.

Satellite L300 suddenly stopped working - new motherboard needed

My Sat L300 suddenly stopped working the other day.
It kept freezing to start with, then nothing at all. So, I kill-disked the HDD and tried to re-install Windows (XP).
During the install it threw up a message that some internal components had been incorrectly installed and needed to be reinstalled.
I was told to remove the memory cards and re-seat them.
That did not work. I thought that perhaps the HDD was damaged, so I fitted a new one, and started to reinstall Windows.
Once again, same message. One of my colleagues at work suggested that the Motherboard was probably U/S.
So I have been trawling the .net to find a replacement. Laptop out of warranty! I am told that some other serial numbered motherboards will work with this laptop. Don't really want to get a motherboard only to find its never going to work! My unit has an SPS number of: V000138330.
I am being offered one with an SPS of: V000138390.
Any ideas? Will this one work?
And if it does, will it give me the functionality that I used to enjoy?!
Sorry for the long sob story.
Any advice gratefully accepted.
ANDY-N

Hello Andy
Sorry but can you tell us more about your notebook? which model do you have exactly (L300-xxx)?
Do you have European model?
Has your notebook valid warranty?
Maybe I have misunderstood something but why you want to exchange mainboard if the warranty is probably still valid?

My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?, My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?

My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do?, My charger doesn't want to plug in to the phone,it suddenly stopped working.What should I do? iPhone 5

Clean the lint/debris from the charging port and plug the cable in.

Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!! SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.

The issue: Outlook to iPhone sync failure – Sync suddenly stopped working for calendar events but continued for contacts and notes.   Finally Fixed!!!
SUPPORT TEAM – PLEASE SEE THIS – Complete explanation of cause and correction steps.
The cause: It is now clear what caused this problem. For years I had several “all-day” events in my Outlook calendar (birthdays, anniversaries, etc.). In May 2012 I decided to make some of them one hour events so I could add alerts to remind me of the event. I did this by dragging them in Outlook to the time I wanted and expanding them to the time slot desired and then adding the alarm.
The symptom: Syncing stopped working for the calendar but continued working for contacts and notes. I didn’t realize sync was failing until months later when I missed two very important phone calls, so when I noticed it the cause was not obvious.
The failed attempts: I’m head of a software firm and my calendar sync is a crucial to my business life so I took this on with a vengeance. From a quick look at events in Outlook and the iPhone I could see that the problem started in May 2012. Events before May were in both Outlook and the iPhone but events after May were only one or the other. Unfortunately I had changed several other things at the same time relating to other events so again the cause was not obvious. MANY calls with AppleCare proved them incompetent so my internal IT guys assisted trying many things. We tried a huge number of calendar changes and several versions of iTunes, iPhone OS and Office as well as both iPhone 4 and 5, all without success.
The fix: After 18 months of frustration, MANY hundreds of $ expense and MANY hours of wasted time I saw a blog that had a calendar sync problem and it indicated all day events were related. I changed the display of the Outlook calendar to the list view, added columns so I could see “all day” event check marks as well as times of events, sorted on the “all day” event column to move them to the top, and for all events that were “all day” events AND had a start and end time, I removed recurrence and then added the annual recurrence back…
After I fixed all events that had BOTH “all day” set and had a start/end time, I tried another sync. It synced for the first time in 18 months!
Problem occurred May 2012 – fixed Nov 2013

Hi, to remove dummy '_ModGrp' entries, rather than crashing the 'Suppr' key on your keyboard, you can use this basic VBA macro (launched for instance from Excel).
It will recursively remove all '_ModGrp...' folders
Sub RemoveFolders_Click()
    Dim oOutlook As Outlook.Application
    Set oOutlook = New Outlook.Application
    Set objNameSpace = oOutlook.GetNamespace("MAPI")
    Call CleanFolders(objNameSpace.Folders)
End Sub
Sub CleanFolders(objFolders As Outlook.Folders)
    For i = objFolders.Count To 1 Step -1
        If Left(objFolders(i).Name, 7) = "_ModGrp" Then
            objFolders.Remove( i )
        Else
            If Not objFolders(i).Folders Is Nothing Then
                Call CleanFolders(objFolders(i).Folders)
            End If
        End If
    Next i
End Sub

HT201263 My iPod touch suddenly stopped working. It was fine, but when I went back the screen had gone black and I was unable to turn it on. It is now unresponsive and my computer does not recognize it when it is plugged in. What should I do?

My iPod touch suddenly stopped working. It was fine earlier, but when I went back a few hours later, the screen had gone black and I was unable to turn it on. It is now unresponsive and my computer does not recognize it when it is plugged in. I thought it just needed to be charged but there seems to be a larger issue now. What should I do?

Let your ipod die. Then when it is dead charge it adn turn it back on. After that it should be fine.

HP Pavilion dm1-4000au Entertainment Notebook PC_Keyboard and Touchpad Suddenly Stops Working

Hi there,
I have an HP Pavilion dm1-4000au Entertainment Notebook PC (QG411PA) running Windows 7 Ultimate 32-bit for more than a couple of years already. During those times up until now, whenever my laptop is on standby for an hour or so, its keyboard and touchpad suddenly stops working, regardless if its running on battery or on AC power.
I always ensure that I have an external mouse in order for me to navigate properly and pull up the on-screen keyboard in order to type once that issue arises.
All appears to be updated in terms of Windows Updates and I even reformatted it, but issue still persists.
Is this particular issue that I am experiencing a harware issue? Perhaps a software issue? Or maybe a defective model itself?
Your prompt response is highly appreciated.
Sincerely,
Led
This question was solved.
View Solution.

Dear Customer,
Welcome and Thank you for posting your query on HP Support Forum
It looks like you are facing difficulties to resolve Touchpad Issues with your Notebook
We will surely assist you with this
Steps to drain the Static charge and loading default BIOS settings to resolve the issue
Step 01. Turn OFF the Notebook
Step 02. Un-plug the Power/AC Adapter and also remove the Battery too
Step 03. Press and Hold the Power Button of the Notebook for a full minute
Step 04. Now let's re-insert the battery back in and plug back the Power/AC Adapter
Step 05. Start the Notebook and keep tapping F10 Key during the startup to access the BIOS
Step 06. Once you get to the BIOS, Please press F5 or F9 Key to load setup defaults for the BIOS
Step 07. Now let's press Esc/Escape Key. Save Changes and Exit - Yes
Step 08. Now please wait till the Unit loads the Windows Operating system
Now please download and re-install the touchpad drivers for your Notebook from the HP Support Site
Please Click this Link to find more troubleshooting steps to resolve this issue
Hope this helps, for any further queries reply to the post and feel free to join us again
**Click the KUDOS star on left to say Thanks**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.
Thank You,
K N R K
Although I am an HP employee, I am speaking for myself and not for HP

My iTunes suddenly stopped working and doesn't recognize any of my devices and gives me a AMD error. I've tried several times to uninstall all Apple programs and reinstall to no avail. I'm running windows 7 on a Dell laptop. It worked fine for years .

My iTunes suddenly stopped working and doesn't recognize any of my devices and gives me a AMD error. I've tried several times to uninstall all Apple programs and reinstall to no avail. I'm running windows 7 on a Dell laptop. It worked fine for years then I decided to update my iPhone 4S and it didn't recognize it or any other iPod or iPad.
Can someone please help ?

I am having all sorts of problems with 9.1.1.Crashes and not only iTunes but I have to restart all the time.
GET TO WORK APPLE !!!!

Outputs Suddenly Stopped Working.

I have a 5th gen Ipod that I've taken very good care of. Until yesterday I've had no problems with it at all. I was using the Ipod in my car w/ my Itrip and the Audio suddenly stopped working. I assumed it was the Itrip not working correctly, so I plugged it into a set of speakers (via the bottom output) but that wasn't working either. Then I plugged headphones in and there is no audio feeding through the headphone output either. I can see on the screen that the songs are playing on the ipod, but apparently the outputs are not functioning correctly. I tried all of the "Rs" recommended in troubleshooting but those did not help. Any suggestions?

i have the exact same problem. Although i am able to here the clicks throught the headphones which makes me wonder that this is something with software. although i have restored and reinstalled and all that, nothing.
Anyone have a solution?

Ethernet suddenly stopped working for no apparent reason

My late 2011 MBP is usually functioning as a desktop with external display and keyboard/trackpad, so I have it connected via ethernet when it's on the desk. However, my connection suddenly stopped working for no apparent reason.......... BUT clearly not a router problem as there's no problem with the wifi connection. System Preferences > Network > Ethernet is telling me:
Status: Connected. Ethernet has a self-assigned IP address and will not be able to connect to the internet.
Dunno how this happened, as to my knowledge I didn't actually do anything to cause this problem, just randomly stopped working. Any solutions much appreciated, thanks :-)

Please post a screenshot of the Network preference pane. Be careful not to include any private information.
Start a reply to this message. Click the camera icon in the toolbar of the editing window and select the image file to upload it. You can also include text in the reply.

Satellite L300 - Built In webcam suddenly stopped working

Hello,
I have a Toshiba Satellite L300 with a built in 2.0 USB camera and a windows 7 operating system, the camera suddenly stopped working since about 2-3 weeks ago with unknown reason!
I already tried system restore, un-installing and re-installing the camera driver, preformed a full scan by kaspersky internet antivirus 2012 (up to date), and I also ran a complete system and drivers troubleshooting ... and the problem still exists ...
When I use the windows live movie maker it gives me an error saying: cant record audio or video from the selected device. Make sure that the device you're trying to use is installed properly and not currently in use by another program.
The microphone works well on skype but the camera doesn't open!
Please tell me how to fix it, what am I missing?

> webcam appears in the device manager
Is it marked with an yellow exclamation mark?
Usually if the webcam software has been installed, you should be able to start this software going to:
All Programs -> Toshiba
There you should find the webcam software check if you can use and control the webcam after this software has been started normally the webcam control bar should pop up if you would move the mouse cursor above the upper display area PS: the bar can be moved to other area too; left right or bottom

MacBook 2008 wifi suddenly stopped working and says no wifi hardware. Took it to an apple shop, they said it could be the airport card but wouldn't do anymore then that. Any help on how to fix this? How do I know if it is the airport card or not?

MacBook 2008 wifi suddenly stopped working and says no wifi hardware. Took it to an apple shop, they said it could be the airport card but wouldn't do anymore then that.
Any help on how to fix this? How do I know if it is the airport card or not?
is there anything else I can try first?
thanks

If the technician at the shop is competent, he has given you a diagnosis that should have identified the problem. You could run the Apple Hardware Test to verify the findings:
https://support.apple.com/en-us/HT201257
Note the Apple Hardware Test is not definitive.
Go to the iFixit.com and Powerbookmedic.com web sites. They have parts and installation instructions. To install an Airport card is fairly easy.
Ciao.

WRT54GS suddenly stopped working

Similar Messages

Maybe you are looking for