WRT54GS v.7 wont give my xbox a ip address or summin

I have a WRT54GS v.7 and when i try to get on xbox live it gets to the ip address part of the test and it fails ive already tried puttin in myv own ip address stuff and it still doesnt work....been tryin to get this to work for like 8 hours

change the MTU settings on the router to be 1365 ... trigger ports 88 and 3074 .. if any problems , let me know ...

Similar Messages

WRT54G new, Ports wont forward and more...

Hello,
I just got this new Wrt54G router with air-pipe isp. And i have ran into a number of problems.. i have tried to self fix them and have gotten no where.. soo where to start.
My router will not connect to the World of Warcraft downloader or any other part, it says "Behind Firewall"
So i looked up the problem, tried forwarding ports that are needed. i used a static ip i created. i dont know if i should be using it. The download wont even download .001 kb so nothing there.
My Routers config is at the Standerd DHCP setup. (no other games will work. either)
I have unchecked Block Anonymous Internet Requests in security.. still nothing. Turned of my computers Firewalls and everything.
I have one other computer connected to the router. i dont know if it makes a difference. And i am running windows Vista Home
Problem #2, Xbox Live.
This will connect, but it shows a very poor connection and it states because the NAT is on moderate. Not open like it should be. So i have again tried to Port Forward the needed ones, Nothing. Firewall is turned off, Nothing. Tried to give the Xbox a Static IP and then use the DMZ option. Nothing.. So any walk through, guides, ideas. anything will help. its getting really frusterating.
ps, im only 15... try and put and explanations into "Lamens" terms xD Thanks.
Message Edited by 69mach1 on 01-29-2009 02:26 PM

Try to hard reset your Linksys Router and re-configure it, Press and hold the reset button for 1 minute...Release the reset button...Unplug the power cable from your router, wait for 1 minute and re-connect the power cable...Now re-configure your router...Check if that makes any difference, else you need to Upgrade your router's firmware...You can download the latest frimware from here , Follow these steps to upgrade the firmware on the device: -
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

HT201269 I recently aquired a new iphone 4s because my old one broke. I backed it up on my itunes but now it wont give me the option of using the phone, it just says connect to itunes. I have synced it several times now and dont know what to do, please he

I recently aquired a new iphone 4s because my old one broke. I backed it up on my itunes but now it wont give me the option of using the phone, it just says connect to itunes. I have synced it several times now and dont know what to do, please help me!!

I recently created a new apple ID
Bad idea.
Content bought with an Apple ID is forever associated with that Apple ID. Apple will not transfer content from one Apple ID to another and Apple will not merge Apple IDs. Unless you are prepared to forfeit all the previously purchased content and buy it all again with the new Apple ID, you will need to maintain the old ID to update and redownload your content.

I have brought a iphone 4 and the person i brought it from has not deleted her icloud account i need her pasword to delete it but hse wont give it to me what can i do how can i add my icloud account can you give me a reasonable answer please. thank you

i have brought a iphone 4 and the person i brought it from has not deleted her icloud account i need her pasword to delete it but hse wont give it to me what can i do how can i add my icloud account can you give me a reasonable answer please. thank you.

The seller needs to follow this procedure:
http://support.apple.com/kb/TS4515
If she refuses, then as Tim suggested the iPhone is probably stolen. You'll need to contact your local police department and ask how to proceed.
Regards.

What do you need to do to get your pictures back after you just restored your phone? it says "downloading" but wont give me any of my pictures back that i took awhile ago

what do you need to do to get your pictures that you took awhile ago back on your iphone 4s after you just restored your phone it? it says "downloading" but wont give me any of my pictures back that i took awhile ago. I backed everythign up at the apple store while the person who helped me watched me do it. i have 1,796 pictures i took before i restored my phone, but it wont let me see them. it just says "downoading" and i will be devestated if all of my pictures are gone. please help me!

You would have received a prompt telling you that you didn't have sufficient space to beck up your phone if that was the case. Also, not everything on your phone is stored in the backup so you wouldn't need 11.7GB to back it up. You can see the size of your backup by going to Settings>iCloud>Storage & Backup>Manage Storage, tap the name of your phone under Backups and look under Options.
If it says "downloading" it's probably still downloading your pictures from iCoud. Check Settings>iCloud>Storage & Backup at the bottom to see the status of the restore process.

Can AirPort express be used for AirPlay with my home stereo, and to give my Xbox 360 a WIRED internet connection via ethernet, simultaneously?

I am considering buying an airport but I am not sure if it will work how I would like it to. I need it for two things. The first would be to use for AirPlay with my home stereo. The second would be to use as a way to give my Xbox 360 a WIRED internet connection via the ethernet port. I would like to do these things simultaneously, rather than constantly changing the configuration and being limited to a single function each time I do so.
Thanks!

The 802.11n AirPort Express Base Station (AXn) can be configured as a wireless Ethernet bridge. In this configuration, it would join an existing wireless network and its Ethernet port would be enabled for a wired client, like your Xbox 360. This configuration would also support AirPlay simultaneously.

After i download it wont give me the set up wizard

i run the download but when it is finished downloading it wont give me the set up wizard

You can find the latest Firefox release in all languages and for all Operating Systems here:
*Firefox 12.0.x: http://www.mozilla.org/en-US/firefox/all.html
*Firefox 3.6: http://www.mozilla.org/en-US/firefox/all-older.html
Be aware that Firefox 3.6.x versions are no longer supported with security updates.
* https://support.mozilla.org/kb/firefox-36-no-longer-supported

My Iphone 4s Will not delete the songs I want it to. I've tried Turning off "Show All Music" and then swiping left on the song to delete it, but it wont give me the option to delete the songs. Please help. (this is iOS.7 btw)

I've tried Turning off "Show All Music" and then swiping left on the song to delete it, but it wont give me the option to delete the songs. Please help. (this is iOS.7 btw) It only does this for some of the songs, but the rest of them I can delete. This is really annoying, please help me ASAP. Thank yall for your time

I've tried Turning off "Show All Music" and then swiping left on the song to delete it, but it wont give me the option to delete the songs. Please help. (this is iOS.7 btw) It only does this for some of the songs, but the rest of them I can delete. This is really annoying, please help me ASAP. Thank yall for your time

HT2534 wont give me an option for no credit card

Wont give me an option for no credit card

You can create an iTune and App Store account without credit card details
1. Sign out of current Apple ID if you are sign-in to one (important)
2. Go to App Store and select a free app
3. Tap INSTALL APP
4. Create New Apple ID
5. Confirm Your Country
6. Agree with Terms and Conditions
7. Fill in your Apple ID and Password (you must create a new Apple ID; don't use your old Apple ID)
8. Create and answer your secret question
9. Select NONE for Payment Method
10. Fill in Billing Address
11. Submit application for new Apple ID
12. Wait for verification email
13. When email arrive, verify your account
14. Start downloading your free apps

HT201363 I cant reset my security questions and answers. Every time I try to have the reset link sent to my rescue address all it does is ask me to verify the email. I keep doing this and still it wont give me access to the reset questions

I can't reset my security questions and answers. Every time I try to have the reset link sent to my rescue address all it does is ask me to verify the email. I keep doing this and still it wont give me access to the reset questions. Anyone know what else to try?

Jaisah 2nd gen ipod touch wrote:
... All I want to do is reset my security questions because I created my account about 7 years ago and I cant remember the answers ...
Forgotten Security Questions / Answers...
See Here > Apple ID: Contacting Apple for help with Apple ID account security
Ask to speak with the Account Security Team...
Or Email Here > Apple Support iTunes Store Contact
More Info > Apple ID: All about Apple ID security questions
Note:
You can only set up and/or change a Rescue Email Before you forget the questions/answers.

WRT54G wont connect with xbox 360

i had my main computer hooked up to the wrt54g with a cable and had a laptop on the wireless and the xbox hooked up on a cable also. im selling the main computer and using just the laptop and now the xbox wont connect with anything. its driving me insane. at one point i had it but the xbox lost it again and has not worked at all.
do i have to have the laptop hooked up to the wrt54g for the xbox to work? when the laptop is hooked to the cable it works and when i disconnect it stops working yet i could run my old pc and this laptop wireless and xbox still worked.
i uninstalled the linksys advisor program and reinstalled and finally said screw it and deleted it and now the laptop connects finally but still no xbox.

Do the following settings on your Router for X-Box to connect...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3) Click on set-up and change the MTU Size to 1452 and click Save Settings...Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

WRT54GS Wont support Two XBOX 360s online at the same time

Just bought new Linksys WRT54GS to support two XBOX 360s live simultaneously. Can't log both on at same time. It kicks first 360 off when second one tries to log on. How can I fix this and have both NAT types open?

I'm having the same issue. I have comcast as ISP, Linksys modem BEFCMU10 V3, going to a Linksys router WRT54GS V4, two desk tops hardwired to the router, TiVo with a wireless and two Xbox 360s with Xbox wireless adaptors. Each Xbox 360 has a different Live account, one has mine the other has my daughters. Either by itself goes live just fine but as soon as the second unit is brought on the first kicked off. If left on they will take turns dropping off from Xbox Live. One night we alternately texted/chatted from both of our Xboxs to the same third party. When he had signed off for the night and showed be "offline" on my unit my daughters unit still showed him "online" until we shut her Xbox off. In addition the NAT always seems to change. Some times its open, others it's medium or strict. This seems to be related to having one or both Xboxs on. I found an article on segmenting your network by using two wireless routers and running the Xboxes through the router closest to the modem and everything else through the second down line router. I haven't tried it yet. Anything I'm missing? Something else I should try? I've talked to the Geeks and some tell you can't so it and others tell me sure it will but they want $$. I've talked to other gamers that tell they've had two Xboxs on Live with no problem.

Step by step complete setup for WRT54G ver.6 with Laptop and XBOX 360

Hello. I am sorry to post this, I am sure it is a juevenile and redundent question...but I have tried to look for the set up cd (I can find where to download it...though I can find the firmware upgrade or whatever). My friend at work said it would do all the setup pretty much automatically for me.
I somewhat know computers, but you might go ahead and make your replies VERY lamen's terms or I might not be able to follow. Anyways, what I need, is a step by step/screen by screen directions for a secure network. I have made a partial attempt at setting it up and it technically works, but I would feel better if I did the steps a-z in order, so I know that it is done correctly. I also am not totally confident in its security as it is now. (Also, technically, I did not check the XBOX again after getting the new laptop, I am just assuming it is still working because it was before).
My problem is I can't seem to find very good directions for setting up the router...I only find partials or confusing directions.
So here are the things I am trying to connect:
Liksys WRT54G ver. 6
Gateway Laptop running Windows Vista
XBOX 360 - WIRED
(I had a PC and a laptop, but they both died at the same time and I have only been able to replace the laptop at this point...the PC will come later and not sure at this point if it will be Wired or not).
I have a cable Modem between the Router and the wall...I didn't look at that for brand/etc...but I can get it ASAP if needed.
Here are the settings that I have so far:
Changed the Router Name
Changed the SSID
Have DHCP set to 3 (XBOX, PC, Laptop)
Wireless SSID Broadcast: Disable
Username and Password changed to my own info
UPnP: Enable
I may have changed other things without knowing it. So like I said, a complete, step by step screen by screen set up would be totally appreciated. I haven't done anything in the security tab, all that is totally foreign to me, so I am just not broadcasting for now until I can get some help setting things up with you guys.
And if someone is familiar with the Laptop/XBOX 360 setup, and I need to change any of the settings on the XBOX itself, could you please include that in your directions? I know that isn't technically what THIS forum is for, but it would sure be helpful to me if you happen to know both parts anyways.
Thanks a lot (in advance)!

So all you just need to do is, secure your Wireless Network. Follow the setps bellow and change the settings on your Router.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Now see if you can locate your Wireless Network and attempt to connect...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

One day my deskjet all in one 3512 wont give me an option to scan

clicking the icon, you get the option to scan, and you can scan several documents to one file,
but now as i click on the icon, it gives only printer options, if i right click on it, i get an option to scan
but only a single photo, and it wont save as a document, only a jpeg

Hello @garydavis61 , and welcome to the HP Forums, I hope you enjoy your experience!
I understand you're having issues scanning from the software. I would love to help!
I would recommend performing a power reset on the printer. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I'd then suggest downloading and running the scan portion of the HP Print and Scan Doctor.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

BT customer care say they wont give me a full refu...

Hi all most of you all ready know that BT customer care don't care well hears my story.......
Back in August 2011 because of my poor broad band speeds, I was on the old 8 Meg package and their sales department suggested that I would be better off changing to their 16 Meg package as I would be guaranteed a minimum speed of 10 Meg up to 16 Meg, so I took their advice and up graded and sat back and waited to fly around the internet and play games without getting lagged out, but sadly the speed problem still existed and I complained again and again then the tec department said its a hard wire fault then it was a profile problem and they will fix it, but it never got better so I complained again and was told I was getting the correct speed for the package I was on, I tried complaining again but was told their was nothing they could do as I was getting the correct speed for my package, so I just had to put up with it as BT is the only provider in my area.
Then just after this Christmas the problems got worse and I complained again AND FINALLY GOT HOLD OF A TEC GUY WHO FOUND OUT WHAT WAS WRONG, ALTHOUGH BT WAS CHARGING ME FOR A 16 MEG PACKAGE I WAS STILL ON MY OLD 8 MEG PACKAGE HE SAID I WAS NEVER CHANGED OVER TO THE 16 MEG PACKAGE ??.
Well an engineer was sent out to check my connections at home he found no faults and said he will now check the exchange and the next day i had a speed of 16 Meg yes at last.
So next move I contacted the billing department for what I thought would be an easy refund for the over payments but was told to my dismay they could only give me a refund for the last hundred days billing WHAT!! BT have admitted that I was not getting the service I was paying for it was their fault but wont pay me back in full??? ombudsman here I come and trading standards and even my local radio station will like to hear about this and I wont be giving up until I get a full refund this treatment to customers is despicable and I will do every thing in my power to make BT pay up.

Hi Shifty55,
Welcome to the forum. I would be able to take a look at the details of your complaint. Please could you send me in your details using the link found in the "about me" section of my profile?
Thanks
Paddy
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)

WRT54GS v.7 wont give my xbox a ip address or summin

Similar Messages

Maybe you are looking for