WRT54GS v6 1.52.5 firm DMZ does not forward

I just flashed the router with the new firmware version. I still can not bypass the firewall to pass packets to my server. I just want to use a pc for a ventrilo server. PC is xp. No firewall, xp firewall is off. Static IP. DMZ is enabled to the IP. It forwards *nothing*. I watched Wireshark on the PC, no broadcast traffic or anything else ftm. I tried port forwarding for 3784 (ven server port) no joy. I have disabled and enabled uPNP. All off: Block Anonymous Internet Requests Filter Multicast Filter Internet NAT Redirection Everything works besides the router passing external requests to the designated IP address. Any advice? Would chatting with a tech help? I'm pretty much out of ideas.

I got it. The hard boot did not work and the new firmware did not work. I reset the router back to it's original config (reset for 10 sec), reboot, made the single change of turning off uPNP, upgraded the new firmware again, then made manual configurations. That made the dmz option forward all traffic. I then disabled dmz and config'ed the port forward parameters. Thanks for your help guys.

Similar Messages

IPhone does not forward attachments with emails

My iPhone does not forward attachments with emails.

Make sure you open the email and fully download the attachments before trying to forward them. Large attachments are often only partially downloaded unless you tap the option to fully download the.

WRT54GS Router installs fine on PC but does not reconize Router

I just purchased this on Tuesday and trying to install. Everything seems to load using the CD but when it tries to connect to the Internet it errors out. When I check the Device Manager it shows the router as being installed properly. Direct connect to Internet works fine. This is a first time wireless setup in house, brand New computer out of the box running Windows VISTA.
Also am using a D-Link ADSL modem for internet connection.
Any help would be great
Thanks
Skip77

I don’t think you need to install the router but configure it and the setup CD just does that. It does not install anything and there is no way you can find that in Device Manager. So if you are trying to configure WRT54GS, make sure you are using correct CD. Secondly this router is a Cable/ DSL router and does not support ADSL. Your ADSL should be working in Gateway mode and not in Bridge to make this router work with this modem. Check if your modem support Gateway mode and has a build-in DHCP server on it.

ME3600 does not forward frames out one interface in service instance

Hi,
I have an issue with ME3600 running 15.3(1)S. I have a BDI used for CPE
management.
cisco ME-3600X-24FS-M
Cisco IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version
15.3(1)S, RELEASE SOFTWARE (fc1)
This is the BDI and VRF configuration:
interface Vlan1620
ip vrf forwarding 65000:1620
ip address 10.232.28.1 255.255.252.0
no ip redirects
ip vrf 65000:1620
rd 65000:1620
route-target export 65000:1620
route-target import 65000:1620
address-family ipv4 vrf 65000:1620
redistribute connected
The MPLS part is working fine, no issues there. There is also a DHCP
pool handing out IPs to the CPEs.
ip dhcp pool 65000:1620
vrf 65000:1620
network 10.232.28.0 255.255.252.0
domain-name xyz
default-router 10.232.28.1
option 66 ascii 10.232.28.1
dns-server 8.8.8.8
lease 0 0 30
This also works fine and I have verified that CPE has both IP and GW.
Then for the service instance configuration:
interface GigabitEthernet0/5
switchport trunk allowed vlan none
switchport mode trunk
service instance 1620 ethernet
encapsulation dot1q 1620
rewrite ingress tag pop 1 symmetric
bridge-domain 1620
interface GigabitEthernet0/11
switchport trunk allowed vlan none
switchport mode trunk
service instance 1620 ethernet
encapsulation dot1q 1620
rewrite ingress tag pop 1 symmetric
bridge-domain 1620
Traffic to CPEs behind Gi0/11 works:
sh ip arp vrf 65000:1620 vlan 1620 | i 29.26
Internet 10.232.29.26 0 0022.07f3.3450 ARPA Vlan1620
show mac-address-table address 0022.07f3.3450
Mac Address Table
Vlan Mac Address Type Ports
1620 0022.07f3.3450 DYNAMIC Gi0/11+Efp1620
Total Mac Addresses for this criterion: 1
Pinging 10.232.29.26 with 32 bytes of data:
Reply from 10.232.29.26: bytes=32 time=33ms TTL=61
Reply from 10.232.29.26: bytes=32 time=32ms TTL=61
Reply from 10.232.29.26: bytes=32 time=34ms TTL=61
Reply from 10.232.29.26: bytes=32 time=32ms TTL=61
Traffic to CPEs behind Gi0/5 does not work.
sh ip arp vrf 65000:1620 vlan 1620 | i 28.190
Internet 10.232.28.190 2 0022.07f2.76a6 ARPA Vlan1620
show mac-address-table address 0022.07f2.76a6
Mac Address Table
Vlan Mac Address Type Ports
1620 0022.07f2.76a6 DYNAMIC Gi0/5+Efp1620
Total Mac Addresses for this criterion: 1
Pinging 10.232.28.190 with 32 bytes of data:
Request timed out.
Request timed out.
Request timed out.
Request timed out.
This is also confirmed by looking at counters. There seems to be no
egress traffic on Gi0/5.
Service Instance 1620, Interface GigabitEthernet0/11
Pkts In Bytes In Pkts Out Bytes Out
31717 2955368 4569808 1709207624
Service Instance 1620, Interface GigabitEthernet0/5
Pkts In Bytes In Pkts Out Bytes Out
4850878 367975447 0 0
It does work to ping locally from the 3600 though:
ping vrf 65000:1620 10.232.28.190
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.232.28.190, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
I'm not sure how to troubleshoot it further. I've also tried setting up
ERSPAN sessions for RX traffic on Gi0/5 but I don't get anything in
unless I ping 28.1 which is the IP of the interface on the 3600.
Any clues?
Daniel Dib
CCIE #37149
Please rate helpful posts.

It could not have been caused by a virus, since there are no viruses for Mac OS X. I would guess it was a typo when you first setup the account, and when you set it up again, a user may have gone to Preferences and selected the Outgoing mail server drop down menu and inadvertently selected the typo'd server entry.
Mulder

Online number does not forward or go to voicemail

I have an online number which is forwarded to an Australian Mobile. It also set up to go to voicemail if not answered. Neither of these functions work as it just rings out when dialed. Where is it ringing? How do I get the features to work? Why am I paying for something that does not work? Will I get a refund for time elapsed to date?

Do you happen to have Airplane mode enabled?

WRT54G 1.1 Wireless works, but Ethernet does not

Evening,
This evening, I flashed the firmware on my WRT54G V1.1.
Everything went fine, and it said click continue to continue, which I did.
I tried to reset back to defaults (button on back), which as far as I know took, but I still can not access via wired connections. For the heck of it, I hopped on the laptop. Sure enough, the settings did take, because I could see and connect to the default settings (SSID of linksys, default pass, etc).
I looked in the configuration page, and see that it is not pulling an IP from the cable modem. I reset the modem, reset the router, but still can not connect via wired.
I even set my ethernet to a static IP (192.168.1.55) with a 255.255.255.0 mask, and cant even ping the router (192.168.1.1), however, I can ping it on the laptop connected via the wireless.
It appears all my ethernet ports are dead, but, just from an upgrade?
Anyone have any idea?
Any help would be appreciated, thanks.

Hi… Reduce the MTU on that router and check if you can get the connection on wired PCs. Or else reduce the Card speed (link, speed and duplex) to 10 Mb half duplex. This should give you a connection. For internet IP address, make sure you clone the MAC address of the Wired PC to this router (MAC Address clone sub-tab under setup) and power cycle the network. You can also try resetting the router for 1 min again.

Forwarding an (ipad) email does not forward attachments correctly

Dear users,
I would like to have your opinion on the following issue.
I often receive an email sent from iPad, which I am not able to forward correctly. Specifically, some attachments are ignored in the compose window. My friend uses Skype to make screenshosts, then selects them and send them to me. I cannot influence the way they are working and I am glad they have gone so far with technologies...
The received message has 2*N attachments, where N is the number of pictures attached. There is also N text attachments, which I am able to open and read -- they are comments to the pictures. When I forward the email, only the text attachments are attached and sent. They cannot be opened on the recipient side and are of lesser value (they are commenting the pictures). All of the attachments are named in the form "ATT00#.txt" "obrazek #.png", where the cross-hash is a sequential number.
One of such emails looks as follows:
When forwarded, the message (the edit window) receives only the text attachements:
The same message on my GMail account looks as follows. Here, the text attachments are inlined into the email.
Does anybody know, how to tell BB10 to re-attach all the attachments form the original email?
Workaround: Currectly, I forward these emails, when I am in on the GMail webpage. In urgent cases, I download the PNG attachments and reattach them manually in the compose window.
Cheers,

Thanks for confirming the issue dear Polocoste. It is not solved up to now. And I have no new information either. Cheers

Hyperlink does not forward

I am trying to forward an email I recieved with the hyperlink in tact. The forwarded email changes the hyperlink to the url. Any suggestions? Thanks, Susie

AND I have downloaded the latest version of Acrobat Reader X, and when I select a live hyperlink I get a notice if I want to connect to the linked site, and when I select yes I am still not directed anywhere... it's a dead-end.
It seems like something has changed within InDesign CS4 within the last two months, now there seems to be a hyperlinkage inability for PDF's.
It worked fine for me before this time just using basic Preview... and now nothing.
And I need this PDF by the end of day

Virtualized bridge does not forward packets to other interfaces

I'm running OS X as a host with VirtualBox. In VirtualBox I set up an Arch VM with these interfaces:
- enp0s3, which is a plain NAT adapter for internet connectivity.
- enp0s8, which is an internal network made by VBox. Connects to some other VMs.
- enp0s9, which is a host-only adapter connected to OS X.
- 9net, which is tinc connected to a remote network over enp0s3
I can establish connections from any of enp0s8, enp0s9, and 9net to the bridge itself (172.31.2.1),
but I cannot actually access hosts connected on other interfaces, which is the main point of the bridge.
Here are some outputs:
root@bridge# ifconfig
9net: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500
inet6 fe80::cd3:17ff:fece:125 prefixlen 64 scopeid 0x20<link>
ether 0e:d3:17:ce:01:25 txqueuelen 500 (Ethernet)
RX packets 106 bytes 9626 (9.4 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 217 bytes 32956 (32.1 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
9net-bridge: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 172.31.2.1 netmask 255.255.0.0 broadcast 172.31.255.255
inet6 fe80::a00:27ff:feba:1c7d prefixlen 64 scopeid 0x20<link>
ether 08:00:27:ba:1c:7d txqueuelen 0 (Ethernet)
RX packets 268 bytes 34588 (33.7 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 28 bytes 2308 (2.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.2.15 netmask 255.255.255.0 broadcast 10.0.2.255
inet6 fe80::5a00:bac1:14b3:a86d prefixlen 64 scopeid 0x20<link>
ether 08:00:27:cf:85:27 txqueuelen 1000 (Ethernet)
RX packets 546 bytes 254262 (248.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 1429 bytes 1360430 (1.2 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp0s8: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500
inet6 fe80::a00:27ff:fed2:59e prefixlen 64 scopeid 0x20<link>
ether 08:00:27:d2:05:9e txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 279 bytes 39854 (38.9 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
enp0s9: flags=4419<UP,BROADCAST,RUNNING,PROMISC,MULTICAST> mtu 1500
inet6 fe80::a00:27ff:feba:1c7d prefixlen 64 scopeid 0x20<link>
ether 08:00:27:ba:1c:7d txqueuelen 1000 (Ethernet)
RX packets 190 bytes 30844 (30.1 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 108 bytes 10454 (10.2 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 0 (Local Loopback)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions
root@bridge# brctl show
bridge name bridge id STP enabled interfaces
9net-bridge 8000.080027ba1c7d no 9net
enp0s8
enp0s9

I'm not sure - I'm trying to script Bridge to hand off a file to PShop and run a script using the cross-DOM method. It opens the files, but I can't get it to run the script.
Still working on it - will try messaging method next, I guess.
The samples aren't there, so I'm running blind, a bit.
rickb

Repeater does not forward data packets

Hello all!
I have following setup:
A root access-point ap1, model AIR-AP1231G-E-K9 with IOS 12.3(8)JEE, is configured with one SSID on VLAN 1 (native) and working fine.
Now I would like to add a 2nd access-point ap2 of the same model with the same IOS version as a repeater to extend the WLAN coverage of the overall network.
I managed to configure the 2nd access-point successfully as repeater (same SSID settings, infrastructure ssid set, parent 1 mac-address set) and it associates successfully with the main root access-point.
Now I observe following effect: As soon I leave the coverage area of the first AP and enter the area of the repeater, the client (iPhone, Laptop or any other WLAN device) associates successfully to the repeater (confirmed with "show dot11 ass" and due to the log entries of the repeater) but the data packets are not forwarded to the main access-point. There is no IP connectivity to the root AP or internet anymore.
Another example which might lead to the solution is following observation:
I have my laptop connected to the wireless network with two console sessions open. In one I run a ping to the first AP, ap1 (10.200.3.5) and in the other console I run a ping to the repeater ap2 (10.200.3.6). Both access-points reply.
Now if I enter the coverage area of the repeater, my laptop gets associated to it and the ping to the first AP ap1 times out.
Again, it looks like that the repeater denies to forward traffic to the main root AP.
I have no clue why this happens, nor are there any log messages available which might explain this issue.
I hope someone can help me finding the problem.
The configuration of the working root access-point ap1 as the repeater ap2 is attached.
Thank you!
Best regards,
Bernhard

You have configured sub-interface on radio interface & not in ethernet interface at Root AP end. change the config like below & see.
dot11 ssid Internet Las 3 Marias
   vlan 1
   authentication open
   authentication key-management wpa
   guest-mode
   infrastructure-ssid
   wpa-psk ascii 7 xxxx
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip
encryption mode ciphers aes-ccm tkip
bridge-group 1
ssid Internet Las 3 Marias
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
channel 2412
station-role root access-point
world-mode dot11d country-code US both
interface Dot11Radio0.1
encapsulation dot1Q 1 native
bridge-group 1
Here is a reference post for a similar setup (vlan 110 is native vlan though)
http://mrncciew.com/2013/01/20/autonomous-ap-repeater/
Also suggest to configure WPA2/AES (instead of WPA/TKIP), if it is supporting in this AP model, command syntax is like below.
dot11 ssid xx
authentication key-management wpa version 2
int d0
encryption mode ciphers aes-ccm
Let us know how it goes
HTH
Rasika
**** Pls rate all useful responses ****

When I reply or forward a message with an attachment the attachment does not forward with the email

Someone sent a message with an attachment. I replied but the attachment doesn't show in my reply. I want to be sure the attachment goes with the reply.

Unfortunately Micrisift have difficulty with understanding standards so they make mail programs that do not correctly encode attachments. Thunderbird can display them, but not forward defective mime encoding. This is a conscious decision of the developers, they are not spreading what they see as defective mail.
Forward such mail as an attachment. It is on the message menu (Alt + M) on on the drop down beside the forward button.

RV220W DMZ not working and protocol 41 packets not forwarded

After fighting a brand new RV220W for hours I am just about giving up on it.
It does not forward anything the to the DMZ server including the IP protocol 41 packets needed for our IPv6 6in4 tunnel.
Nor does it send protocol 41 packets to the WAN.
TCP and UDP packets are only forwarded to the DMZ server if specifically done by a firewall rule.
CISCO support was not able to solve the problem after half an hour on the phone.
Factory resets and absolutely minimal configuration changes have been tried to no avail.
Firmware is 1.0.1.0.
The hairpinning problem as well as the weird time problem cause by ticking the daylight savings box has been observed as well.
Should I return this thing having learned that CISCO quality is a thing of the past ?
The Netgear WNDR3700 it was supposed to replace, due to the SNMP support found in this router, happily forwards packets at half the price.

Manually creating a firewall rule with protocol 41 in the backup config file and restoring it makes no difference.
(A new checksum for the configuration file may be generated by md5sum when the checksum line has been deleted)
Default should be to route all IP packets regardless of protocol number to the DMZ server, when DMZ is enabled. Now the router returns a ICMP port unreachable message to the WAN sender.
Update:
The problem is only present when the dual stack IPv4/IPv6 feature is enabled, so after all it may be a bug and not a design decision. Waiting for Cisco support to verify/advice on this.
BTW it is unbelievable, that the configuration file (plain text) saved by the backup function in the router cannot be read / used by Cisco suppport. They can only handle something which can be displayed in a browser (sic!)
Update 2:
Further testing has shown, that the option of forwarding of protocol 41 packets for 6in4 tunnels in any mode (IPv4 only or IPv4/IPv6) is randomly enabled. Sometimes suddenly working after 30 minutes. At other times not at all even after a reboot. Occasionally it has been working in both modes.
I have provided information about this to CISCO.
Cisco support has recognized this to be a problem of the current software 1.0.1.0 and is issuing a refund of the router.

VPN does not work on WRT54G v6

Hi,
Just bought a new wireless router (WRT54G v6) to replace my old one who just died after 4 years of loyal services (WRT54G v1) but VPN does not go through even though all the VPN passthrough options are enabled.
I'm using a VPN connection created through the Network connection wizard of Windows XP. This same connection worked fine with my previous router (WRT54G v1) but not with the new one (WRT54G v6). What can I possibly try to check or do.
I also upgraded to the latest firmware 1.00.9 to no avail.
Also, if it can help, when I connect my cable modem directly in my computer the VPN goes through. Through the router, nothing, wired and wireless connections the same.

I changed the flash and it still doesn't work.

WRT54G v5 admin screen does not load completely

I have a WRT54G v5 and when I go to the admin screen (http) it does not load completly. It was working the other day. I was in the process of downloading a newer version of the firmware, I am using 1.0.6 and was looking at the 1.0.9. I have it on the computer but have not applied it to the router yet.
I am using IE7 and was able to view the page previously with IE7 but am not able to now. I have rebooted the router (cold start). No difference. I can still get to the internet and the wireless is working also, I just cannot make any changes to the router.
I need help, if someone is willing.
Thanks
Dave

Check if your firewall is on. I was having the same problem and I just shut down Zone Alarm...

WRT54G does not allow wireless connections

I installed a WRT54G V8 for my neighbor. After much pain and fights with the wizards I got it to where it works with wired computers. I set up the wireless and named it, selected security, recorded the Key, even had the wizard record the computer setup program on a USB drive.
The two wireless computers I have tried can both see the network but clicking connect does not get me the enter key window. Actually nothing happens after showing connecting for about a minute. I tried the setup program and it said it could not set up the computer. I tried setting up the parameters manually and then connecting nothing happens.
But the routers DHCP table shows the names of the two wireless computers as being connected.
Some time when I try to connect (with manual entered data) the network page will show "Not Connected" over the top of the network name. But the button at the bottom of the page has switched from "Connect" to "Disconnect" and the machine is in the DHCP table.
Any suggestions?

Greyhair wrote:
I am using XP SP2 on both of the wireless computers and I am using the default windows client. In the wireless networks tab is where we tried setting up the network manually. Are you saying that with a WRT54G I can have only one wireless network installed on the machines?
I will try it on one of the machines this afternoon when I go over to try again to get it to work.
Why is this so hard!??!
Hi greyhair ,
Ridcully did provide some good information.
The wireless network tab .
for that ,
strt>control panel>network connections or (network and internet connections) icon> network connections
Right click on the wireless network connection listed
go to properties ,
here you will find three tabs - general >wireless networks>advanced
you need to click on Wireless network
and remove preffered networks from the network list (even yours )!
and click ok !
and again , right click on wireless network connection > go to View aivialable wireless networks ....try connecting to your network by first clicking (highlighting)
on the network name , and then click connect.
any problem , feel free to ask here.
pe@c3
~~~Nobudy's Perfect , i try To Be So ! Each n every moment of maH LYF , AND I THINK dat wats make Me "Different" From others....~~~

WRT54GS v6 1.52.5 firm DMZ does not forward

Similar Messages

Maybe you are looking for