WRT54GS Will Not Enable Security

I am trying to turn on the wireless security for my WRT54GS router and it will not work. I accessed the router through my browser (192.168.1.1) but when I go under Wireless > Wireless Security it will not let me change the pull down menu off of Disabled. I've tried all of the options on the pull down menu and it just automatically switches it back. I've tried resetting to factory defaults but that did not fix the problem either. Any thoughts??
Solved!
Go to Solution.

Great idea! That did the trick, though it was Firefox that was giving me trouble and Explorer that actually worked. Thank you for the help!

Similar Messages

SF300 LAG port doesn't work, LACP will not enable.

I'm trying to configure something that seems pretty trivial.
I need 2-3 ports to participate in a LAG port. First off, I get the "Port X belongs to a vlan" if the participating port is something other than access vlan 1. This is totally useless. I need these ports to be dot1Q tunnels. This happens even If i set the default vlan to 300, (300 is my native or PVID). Another piece that doesn't seem to work is that LACP will not enable, even if I throw in the towel and make my ports access vlan 1. What gives? I've tried this on the only firmware available which has no patches avail yet. I've tried this on 2x 24ports, and on 2x 48 ports.. all the same issue.

Hi I just gave it a try you can see my screen captures below.
If you are having trouble, have a word to the good folk at the SBSC if the switch is still under phone support coverage.
http://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Maybe play it safe and delete your settings and start again... Here are some screen shots from my attempt.
I have to admit I enabled LAG and LACP before I created vlan 100.
you can see i have the same software as you.
add the ports and enable LACP at the same time.
ports 47 and 48 are still excluded from my Tagged Vlan
Now I selected port drop down for VLAN100 and selected LAG.
I then received and then modified the following screen capture.
Note I manually added LAG interface 1 as a tagged member of VLAN 100.
Why Lag interface 1, because I created LAG 1 previously, as seen in a previous screen shot above.
regards Dave

IMAP will not enable

IMAP will not enable in mail server, using Panther 10.3.9 server
Even though I do not plan on using POP it will not enable either. SMTP
is enabled for both out going and incoming.
postconf -n
always_bcc = [email protected]
command_directory = /usr/sbin
config_directory = /etc/postfix
daemon_directory = /usr/libexec/postfix
debugpeerlevel = 2
enableserveroptions = yes
inet_interfaces = all
luser_relay = postmaster
mail_owner = postfix
mailbox_transport = cyrus
mailq_path = /usr/bin/mailq
manpage_directory = /usr/share/man
mapsrbldomains =
messagesizelimit = 10240000
mydestination = $myhostname,localhost.$mydomain,70.88.14.125,fieldshop.com
mydomain_fallback = localhost
myhostname = server.fieldshop.com
mynetworks = 127.0.0.0/8
mynetworks_style = host
newaliases_path = /usr/bin/newaliases
queue_directory = /private/var/spool/postfix
readme_directory = /usr/share/doc/postfix
relayhost =
sample_directory = /usr/share/doc/postfix/examples
sendmail_path = /usr/sbin/sendmail
setgid_group = postdrop
smtpdclientrestrictions =
smtpdenforcetls = no
smtpdpw_server_securityoptions = gssapi,cram-md5,login,plain
smtpdrecipientrestrictions = permitsasl_authenticated,permit_mynetworks,reject_unauthdestination,permit
smtpdsasl_authenable = yes
smtpdtls_certfile = /etc/postfix/server.pem
smtpdtlsloglevel = 0
smtpduse_pwserver = yes
smtpdusetls = yes
unknownlocal_recipient_rejectcode = 450
server:~ fieldshop$
also the mail log shows the following
Jan 21 00:20:14 server master[6691]: empty option value on line 20 of configuration file
Jan 21 00:20:14 server master[6691]: exiting
PowerBook Mac OS X (10.4.4)

Here are the contents
cat /etc/imapd.conf
admins: cyrus
configdirectory: /var/imap
partition-default: /var/spool/imap
unixhierarchysep: yes
altnamespace: yes
servername: server.fieldshop.com
sendmail: /usr/sbin/sendmail
mboxlist_db: berkeley
seenstate_db: flat
logrollingdays: 0
logrolling_daysenabled: false
tlscertfile: /var/imap/server.pem
tlscafile: /var/imap/server.pem
tlsserveroptions: use
imapauthlogin: yes
imapauth_crammd5: yes
tlskeyfile: /var/imap/server.pem
imapauthplain: yes
imapauthgssapi: yes
tlsca_filecontent:
quotawarn_frequencydays: 0
tlscommonname:
lmtpluser_relayenabled: false
lmtpluserrelay: postmaster
enable_pop: no
server:~ fieldshop$
PowerBook Mac OS X (10.4.4)

Wrt54g will not play youtube videos

wrt54g will not play videos. I have connected my modem directly to computer and it works fine if I connect thru the router it will not play... Please Help Bill

Is the problem only experienced by one computer or all devices are experiencing the same thing? Since it's working fine directly to the modem, it must really be on the router. Try to upgrade the firmware of the router. Once the upgrade is done, reset the router and reconfigure the settings. You may refer to these links in reconfiguring the router: Setting up a Linksys router with Cable Internet service, Setting up a Linksys router for DSL Internet connection.

Iphoto will not enable photo stream

My iPhoto will not enable Photo Stream. All software is up to date and I have the latest version of iPhoto, in fact Photo Stream was working last week on my Mac. Now all I get is the msg "iPhoto cannot enable Photo Stream". Any thoughts ??

Hey dave2468, as you can tell by my original post, this problem surfaced several months ago and out of frustration for lack of an answer to the problem - I called Apple for support. I was fully prepared to spend the $50 bucks to resolve this issue but fortunately didn't have to. My problem did get resolved after about 1 &1/2 hours on the phone and the solution revolved around resetting my password for my account...can't tell you why other than ghost in the machine issue. Yours may be different issue but wanted to let you know how this ultimately got resolved. I have had no further issues relative to this problem since my phone consultation. Best of luck - I know how frustrating these things can be. B.

The sound on my hp stream notebook pc 14 will not enable.

the sound will not enable. i have tried downloading things to scan and fix the sound card...but they all cost money and i dont even know if it will fix the problem. it will not load the trouble shooting page either so i dont know what else to do. it has blocked all spund on my pc and nothing i try to do will fix it as i have to pay large amounts of money before any programes will fix the problem

@lauralawrence93 ,
Hello and welcome to the HP support forums. Lets see what we can do about your sound issue.
First think if possible could you post back with your systems Product Number.
Until then here are some links you can check out to see if they help.
No Sound from Speakers (Windows 8)
Here is one set of threads from the support forums.
Troubleshooting Guide: Audio does not Work after a Certain Period of Time
Thank you again for posting. Hope to hear back from you soon.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

Itunes will not accept security code although I have checked with bank ant everything is OK!!!k

itunes will not accept security code although I have checked with bank ant everything is OK!!!k

Carlos...
Try this support article > iTunes Store: My credit card's security code or zip code does not match my bank's records

HP 6700 printer will not enable web services.

My HP 6700 printer will not enable web services. I've already downloaded the firmware update, manually entered the IP and DNS numbers... shutdown the printer and turned it back on.But when i try to enable web services it try's for a while then says web services could not be enabled.. any help would be appreciated. I have vista.
This question was solved.
View Solution.

Hi there, two other things you could try (if not already attempted) are:
Check to ensure that you have the latest firmware for your router – review your router documentation/help (or the router manufacturer’s web site) for information on how to check for and install firmware updates.
Restore factory defaults - The factory default option is usually found in the Setup>Tools menu on your printer. Do the following on your device:
Remove/Disable Web Services
Restore factory defaults/settings (depending on the printer this is found under the Setup>Tools menu, or the Setup>Web Services menus, but varies by printer)
If prompted, re-do initial setup of your device and add it to your network
Re-enable Web Services
Once the Web Services information sheet is printed, use the printer claiming code to add your printer to your account on ePrintCenter
If my reply helped you, feel free to click on the Kudos button (hover over the "thumbs up").
If my reply solved your problem please click on the Accepted Solution button so other Forum users may benefit from viewing the post.
I am an HP employee.

Radio will not enable

I am running a 2106 controller with 1242 AP,
Had them on a POE injector on the same switch worked fine, mounted them in the ceiling now the radio will not enable."error in enabling admin status". any ideas?

Hi Paul,
I think you might be running into this issue because the 1242 AP supports the Intelligent Power Management feature (which I didn't even know existed until recently). Have a look at the following.
Power Issue with the AP
When an AP uses a power injector as the power source, in some cases, the AP displays this error message:
CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASSIC inline
This message indicates that the AP is in low-power mode with all radios disabled and detects a Cisco switch that is unable to supply sufficient power to the AP. Even though the power injector, which can provide sufficient power, is connected with the AP, the AP still displays a LOW POWER error message and disables the radios. Therefore, the AP remains in low-power mode.
One possible reason for this issue might be that the AP supports the Intelligent Power Management feature. The Intelligent Power Management feature uses Cisco Discovery Protocol (CDP) to allow powered devices, such as an AP, to negotiate with a Cisco switch for sufficient power. The AP supports the Intelligent Power Management feature. As a result of the power negotiations, the AP either enters full-power mode or remains in low-power mode with the radios disabled.
In this case, the AP might be connected to a switch which cannot provide the necessary power to the AP. Therefore, even though the power injector is connected to the AP that uses this Intelligent Power management feature, it gives priority to the CDP information to identify whether or not the switch can provide the power. Once the AP knows, via CDP message, that the switch does not provide sufficient power, it disables the radios and remains in low-power mode.
The workaround to this issue is to tell the AP to ignore the CDP information for power. You can perform this by telnetting into the APs. Issue these commands to enable the APs to use the power injector:
power inline negotiation prestandard source
power inline negotiation injector H.H.H
The power inline negotiation command configures the Cisco Aironet 1130AG or 1240AG Series AP to operate with a later version of switch software that does not support Cisco Intelligent Power Management power negotiations.
The prestandard source portion of the command specifies that the Cisco switch runs a later version of software that does not support Intelligent Power Management negotiations, but is able to supply sufficient power to the AP.
The injector H.H.H portion of the command specifies that a power injector supplies power to the AP, and that the AP connects to a new switch port with the indicated MAC address (H.H.H). Enter the MAC address (in xxxx.xxxx.xxxx hexadecimal format) of the new switch port where the power injector is connected.
Note: This command should only be used when you move an AP and power injector to a different switch port.
From this good doc;
http://www.cisco.com/en/US/products/hw/wireless/ps441/products_tech_note09186a00800a86d7.shtml#new3
Hope this helps!
Rob

PhotoStream will not enable.

PhotoStream will not enable. When I check the box it unchecks itself imediately. Just downloaded the newest version of Lion. Using a MacBook Pro. Have checked off PhotoStream in System Preferences. What am I missing?

And again
Do you have iPhoto 11 (v9.3) or later? Or Aperture 3.3 or layer?
The exact version is critical to being able to help you.
LN

Bluetooth will not enable(6230i)

Hello
I have a new 6230i and when I go to the Bluetooth menu and select
Bluetooth->On
it goes back to the Bluetooth menu with bluetooth set to 'Off'.
If I turn off the phone and turn back on and try it again, Bluetooth->On, I get the message:
"Switching on Bluetooth"
but it goes back to the Bluetooth menu with bluetooth set to 'Off'.
I have tried the same with a 6230 and Bluetooth switches on everytime.
Does it sound like my new 6230i is broke? Any ideas?
Are there any firmware upgrades which could fix this?

No didnt drop the phone but if it was damaged by a drop i would have expected something else to be damaged. I have used the USB cable, IrDA, camera and normal phone operation and they seem to be ok, just the bluetooth will not enable. This leads me to think it is a problem from the factory.
First thing i tried was taking out the battery as you suggested. I will return to the store and see what they think but is there a Nokia tech support?

Itunes 10.4 will not load - secure link failed

I have itunes 10.4 and the store will not load, I can download apps updates from itunes and ping. but the store will not load. When i run the tests I get secure link failed for the itunes store. when i click on help it tells me I am not connected to the internet. which i am. iam surfing the net. downloading updates drom my computer
here is the info from the tests:
Microsoft Windows 7 x64 Home Premium Edition Service Pack 1 (Build 7601)
Hewlett-Packard HP Pavilion dv7 Notebook PC
iTunes 10.4.0.80
QuickTime 7.6.9
FairPlay 1.12.20
Apple Application Support 2.0.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 3.0.0.2 (333.2)
Gracenote SDK 1.9.1.485
Gracenote MusicID 1.9.1.102
Gracenote Submit 1.9.1.133
Gracenote DSP 1.9.1.43
iTunes Serial Number 003BB1100D966DA0
Current user is not an administrator.
The current local date and time is 2011-08-14 12:54:27.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 9600M GT
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: 87171a288271fe32d3b2edc5e9c2aa21
iPodService 10.4.0.80 (x64) is currently running.
iTunesHelper 10.4.0.80 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name: {46F9BC44-C3E6-41B3-A027-58DFA9E5CD0B}
Description: Microsoft Virtual WiFi Miniport Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {2E31BA71-925D-4325-BAE8-31884B65B8CB}
Description: Intel(R) WiFi Link 5100 AGN
IP Address: 192.168.0.108
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
DHCP Enabled: Yes
DHCP Server: 192.168.0.1
Lease Obtained: Sun Aug 14 12:13:31 2011
Lease Expires: Sun Aug 14 14:13:31 2011
DNS Servers: 66.37.69.141
66.37.69.142
Adapter Name: {66C3DEF0-5D20-4204-8B7E-101F288520E4}
Description: Realtek RTL8168C(P)/8111C(P) Family PCI-E Gigabit Ethernet NIC (NDIS 6.20)
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is on.
iTunes is NOT enabled in Windows Firewall.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was unsuccessful.
An unknown error occurred (-9808).
Connection attempt to iPhone activation server was unsuccessful.
The network connection timed out.
Connection attempt to firmware update server was unsuccessful.
The network connection timed out.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-08-14 12:52:40.

Just a followup; got it to sync but it just synced the old contact info and not any of the new info that I had entered or changed. Where is it getting the old info?

Safari will not open secure sites

Safari will not open any secure sites with a secure login. Anyone have an idea why?

Same issue here and yes, I can get to the secure sites using Firefox, Camino & Opera and no, when logged into the new user account I still can't access secure sites with Safari.
Also, I have been unable to purchase anything off of iTunes since this issue started. Does iTunes use Safariin some way? Any idea why the two things seem to be linked?
After successfully browsing Music Store & selecting the desired purchase, I hit the "Buy" button and get an error message saying that iTunes could not connect to the Music Store. "An unknown error ocurred (0x80010003)." It suggests I make sure my network connection is active & try again, but I'm clearly online.

WRT54G will not block URL's and keywords

Hi everyone
I have my main computer wired to the wrt54g and another second computer wireless. I want to block certain websites from the kids but when I put in keywords or url's the router will not block them for either computer (the wireless on is the main one I want to block)
thanks

it is the latest firmeware update.... and thanks on the mac info
randy

Wifi ac dongle 900 will not enable.

Hi
I am having problems getting my dongle 900 to work.I have the correct drivers installed from hardware and also tried from the BT website online,but it says they maybe fautly.I have also installed the windows update.The item appears in my adapter list as disabled but when I click enable a small window pops ups saying "enabling" then "enabled" but it still tells me it's disabled and will not connect.Also when I diagnose the problem it says"windows could not automatically bind the IP protocol stack to the network adapter".This is the second dongle I have tried same result with both,any help would be helpful as the help desk is no help.
Thanks
Solved!
Go to Solution.

I also ran into this issue, as the original poster never included the solution here's how to fix it:
Click the Start Orb and Right click on COMPUTER then click MANAGE
Go down to SERVICES AND APPLICATIONS then choose SERVICES
In the list that appears scroll down until you see something called "WLAN AutoConfig"
Right click and choose PROPERTIES
In the drop down box next to where it says STARTUP TYPE choose AUTOMATIC and hit APPLY
Once that's done you'll see four buttons under SERVICE STATUS you want to choose START
Hit APPLY and close all windows, your dongle is now enabled
Now you should be able to go back to your network connections and connect to your BT Hub wirelessly.

WRT54GS Will Not Enable Security

Similar Messages

Maybe you are looking for