WRT54GS Wireless Router with Speedbooster.... I need help please!!

Please... anybody!!
I have the above router and all my PC's/laptops are wireless....
They're all set to acquire IP addresses automatically frm DHCP, but I'm still getting IP address conflicts..
When this happens, one PC is fine, but another one will have trouble acquiring one... now this shouldn't happen right?
As far as I can see, the router is set up properly... not changed anything really, apart from the security settings....
This only happens occasionally, but is still annoying....
HELP!!!!

What's the DHCP client list? How do I check that?
I'm assuming it's an IP conflict because whenever the PC tries to acquire an IP address to connect, the other PC that's already connected will pop up with an IP conflict message. And it goes away if I stop trying on the other machine....

Similar Messages

HI I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7. NOW I W...

HI
I HAVE WRT54G WIRELESS ROUTER WITH VERSION 7.
NOW I WANTED TO UPGRADE THE FIRMWARE.
I CHCAKED OUT THE SITE I COULD'NT FIND THE DRIVERS FOR THE VER 7
EVERYTHING ELSE OTHER THAN VER 7 IS PRESENT ON SITE I WANTED TO CHEAK OUT WHEATHER THE VER 7 FIRMWARE ARE AVALIABLE OR NOT PLEASE HELP ME TO DO SO
THANKS
PRAVIN

hi helm
Thanks a lot for your suggestion i got the required farmware
thanks
prav

Configure WRT54G Wireless Router with PUBLIC IP address and use DHCP for internal computers

Hi,I have an Internet online service with 5 public IP addresses. The router and the AP are connected to a switch. I would like to configure a WRT54G wireless router with one of this IP public Address and use DHCP (with private ip address) for the computers that will connect to the AP. As the AP is connected to the switch it is possible that other wired computers that are connected to the same switch can obtain an IP address from the DHCP ?
Thansk in advance

Thanks for your help. Please correct me if Im wrong. After connecte the equipments the way you suggestI setup a static IP address (The public IP) in the WRT54GI enable DHCP in the WRT54G with a range from 10.10.0.100 to 10.10.0.200 (as an example) The gateway is the Public IP address right ? How do I route the 10.10.0.x addresses to the public IP address. Thansk again

My WRT54GS Brodband Router with SpeedBooster: Firmware: v4.71.1 doesn't do wireless

So I set up my PPOE and put in my service username and password and everything works fine on the Landed computer, but it won't connect to my laptop and i can't even enter the Router settings on my laptop. I recently did a firmware upgrade and a hard reset. My laptop says I am connected to the router as well, because it pops the SSID up and says, "Connected To: Ralph Signal Strength: Excellent." WHAT CAN I DO TO MAKE IT WORK!

Richard you did the right thing on hardresetting the router but then after you resetted it,i think you didnt type in the username and password, because after the reset it wiped the pppoe settings on the router. So retype the username and password in the router and reconnect to your network,and personalizing your wireless settings is better.

Router problems..I need HELP PLEASE

I'm in a bad spot... I just got my kids their own tablets but when they use their internet it's sucks all the Wi-Fi up... what do I do... we can't do online gaming or anything if they are online.... we have a Belkin N450 wireless N+ Router F9K1003CL we have never had an issue but now I do. Should I get a router just for their HKC tablets or one just for the xbox's. Or is there a powerful device to run all and then some... somebody please help me... I have Comcast super faster internet but the modem, box is several years old
List of device's
2 Xbox consoles one is used for major online gaming
Kindle Fire
Samsung Tablet
Samsung Galaxy S2
2 HKC tablets...they are the ones sucking the power
Nintendo DS

I don't see how getting a seperate router for either would help honestly but you can try. It all comes back to the same thing: the modem. If your sure its the tablets sucking all the power than what I would do is, when it starts lagging check what their doing on the tablets streaming movies can take a lot of juice. Although if you have superfast internet I don't think it would matter.
Good Luck - Jake

Wireless issues with my macbook. Help please.

I just got a new WRT300N and my Macbook connected to it fine once it was set up. However now everytime I leave my house and take it with me, or put it to sleep, when it comes back on to my normal wireless network, the Macbook receives the signal, and shows that it has full access, but i cannot get any internet whatsoever. Please help this is driving me crazy.

yes when it connects it gives it an ip depending on which of my other household laptops was on first. usually is 192.168.1.102 when i restart my macbook it connects just fine. but if i disconnect from the network at all it won't reconnect unless i restart. and everytime it does it shows up in easy advisor as a different device.

DV5-1115 Problems with overheating, need help please

So i have a:
Pavilion DV5-1115
AMD Turion X2 Processor (yuck)
ATI Radeon Graphics Card
Windows 7 (w00t)
So I have a program that tells me the tempature of my computer, as I'm writing this my computer is 130F, if i play any games it's 150-170 EASY. I play fifteen minutes of a game on lowest graphics (simular to Dota) (no battery as well) and my comp hits right at 200 and shutsdown... Anyone have any idea how to make my computer cooler?
EDITED: I do want to mention that I did send it in once for the same problem, sending it in again for the same problem, I am an IT student and use it atleast ten hours a day. So until I have to send it away I need to atleast have a temporary fix.
P.S. I have it on a table with fans blowing under it. (so really this is ridiculous)
P.P.S. Hp makes me sad atm.
Message Edited by JonathanM on 10-27-2009 08:59 PM

hi, i have the same notebook, can i ask you where did you get your graphic card driver? i cannot find it :/
Thanks Watchick

WRT54G Wireless router works on desktop, but not laptop

I have a WRT54G wireless router with version 1.00.4
It works on my desktop, I can log into the net no prob
My laptop however (dell w/ windows xp) does not even recognize it.
Wierd thing is, it worked perfectly with no problems today, I have been going online with my laptop using the wireles router for weeks now..
I haven'tupgraded the firmware, or do anything to any of the computers whatsoever.
When it stopped working, I reset my router/modem, I transfered over my MAC, etc.. but the laptop still does not even recognize my router signal when I try to search for it on my laptop.. It will recognize a handful of other wireless routers from the neighborhood, but not mine.
My desktop is windows xp, and so is my router.
Any helpwould be greatly appreciated.

i had that problem before with the my router and i just did customize the wireless settings. try the the link below, its a great help.
1.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=759&p_created=108422...
2.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=759&p_created=108422...
hope this will help you...
~ lyf_R_foeittee ;o) ~~

Tried to update WRT54G wireless router, upgrade failed, router broken.

I tried to upgrade my new WRT54G wireless router with the new firmware. I got an error message that said "Upgrade are failed". I used the correct version of the firmware for my router (I have a Ver 8). I tried to factory reset, but the router is still broken. Any suggestions on what I could do? The entire page I access via IP is broken. All the text is messed up the the links don't work. I can use the router to access my network, but it will not connect to the Internet at all.
Message Edited by Trax416 on 02-05-2008 01:05 PM

I have no firewalls, and it's for sure not a computer related problem. I have tried on three seperate computers. The upgrade failed, it won't let me access the setup page. I have tried to go onto the Internet since, and it lets me, but 80 percent of all Internet sites don't work. This is what shows up in the router firmware page when I go thru the IP. ýýý†††···ÇÇÇ¶¶¶¼¼¼öööiiiSSS¿¿¿ÂÂÂßßßààà´´´¯¯¯***^^^uuuAAAllØhhÐééé²²²äää–––ÃÃÃBBBâââmmm¾¾¾DDDWWW˜˜˜“““ìììÎÎÎ LLLaaajjÓyyy ¸¸¸ÝÝÝøøøÉÉÉãããÞÞÞ:::×××ÓÓÓkkk’’’nnn™™™³³³©©©ççç œœœxxx~~~ÁÁÁffÍ```ggÍ CCCiiÐ‘‘‘ ŠŠŠ@@@žžž YYYµµµÐÐÐªªª¥¥¥??9èèè___ÆÆÆ‰‰‰ÜÜÜšššÒÒÒ¨¨¨¡¡¡vvváááØØØÙÙÙƒƒƒTTT$$$ÍÍÍŒŒŒÚÚÚÔÔÔ••• ËËËÅÅÅëëëººº‚‚‚°°°|||}}}jjÕVVV„„„\\\]]]rrrbbÅ??;ŸŸŸ[[¶»»»[[[%%IGGG???eeË£££ííí‡‡‡fffooÝOO __¾kkÕGGŽ``Á88oddÇKK•CC†hhÏîîî±±±>>|SS¦77mÛÛÛæææpppÖÖÖ®®®ÈÈÈHH êêê??)ÌÌÌÊÊÊÄÄÄ????:llÙZZ²ŽŽŽWW®99q;;vAA‚ÿÿÿffÌ Message The rest of the pages in the setup menu ether show up blank, or give the same message as above.
Message Edited by Trax416 on 02-05-2008 01:35 PM

WRT54G Wireless Router Problem. Need Help!

I'll start with the basics of my situation and if more details are needed, I will provide to the best of my ability.
I have a comcast cable internet connection. I have 6 computers in my house. Two of them are downstairs (which is where our modem is.) The other four computers are upstairs. All of these computers are Desktop computers with the exception of one laptop.
My laptop (which is Windows XP) can pick up a random wireless signal from the room it is in. I also found out a way to share the internet connection on the computer by going into the properties of my network connection and enabling internet sharing on it. This means if I connect a network cable from my laptop to another computer, I can leech the connection from my laptop and have internet access on the other computer. I also had a switch that I used to connect the other 3 computers upstairs by means of the laptop. The problem was, the laptop was using someone else's wireless connection in the area, and it wasn't strong enough to keep up a constant connection.
I decided, if I can leech someone else's wireless connection, why not have my own. So i recently bought WRT54G Wireless Router and set it up on one of the computers downstairs (because that's where the modem is). It works fine as far as connecting my laptop to the internet from upstairs. My laptop can access the internet through the connection I set up in the LELA program.
Here is the part I am confused about. Everything is plugged in correctly as far as the router is concerned because the laptop can access the internet. But when I connect an ethernet cable directly to one of my other computers (which are Windows Vista, but I didn' t have a problem with it previously when I was leeching someone else's connection), the connection drops on my laptop, and the other computer still can't access the internet. A notice pops up that says its trying to identify the network, but it gives an error that says there is something wrong with the DNS. As soon as I disconnect the ethernet cable connecting my laptop to one of the other computers, the connection is fine again on the laptop. It's only when I connect the computers together that the connection drops.
I just don't understand why it wouldn't work when I created my own network if it worked with another network with no problem. My whole point in getting a wireless router was to have a router within good range to keep up a constant connection on my other computers that aren't in range of the modem downstairs. I just don't know where else to look. I'm not sure if it can be fixed on LELA, manually through my wireless settings, or if it could be a problem with one of my computers' settings. I've tried many different things and I'm not sure what else to do so any help is most definately appreciated. I feel like I've tried everything. I know it's possible because I've one it before, I just need the help because I'm not much of a networking person and I don't know what I should start with to make this work.
Thank you to anyone who can help or even point me in the right direction.

Access router setup page ...Click on the Wireless tab on the Setup page- Here Wireless Network mode should be mixed- Provide any non-linksys name .... Set wireless channel to 11- And wireless SSID broadcast should be Enabled and then click on "Save Settings" >>Now Click on the Sub tab under wireless > "Wireless Security" Change the Wireless security mode to WEP/WPA ...type in the key & click save settings .... >>>>Click on Advanced Wireless settings>>Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" Check the connection once again & see if it works or not ...

Pls help me.i have a problem with WRT54G wireless router.

Dear all, Now i got face some problem with WRT54G wireless router.The problem is after i connect to the internet...the wireless will automatic drop..is that any ppl here got face this and got any solution to solve it...?thanks for sharing..

hi...logon to router's setup page and try changing channel to 11, go to advanced wireless settings, try changing transmission rate to 54Mbps, beacon interval to 50, fragmentation and RTS threshold to 2304, also try upgrading latest firmwar on the router...check whether it maks any difference or not and let me know.

HP Officejet Pro 8500 wireless Networking with LINKSYS WRT54GS wireless router

I have a HP Officejet Pro 8500 wireless printer conneted via WiFi to my LYNKSYS WRT54GS wireless router. I do not have a USB cable or ethernet cable plugged to the printer. I am able to use the 'scan to email button' and the 'scan to network folder' button on the front of the printer and I can pint from the PC to the printer with no problems.
I installed the HP printer software from the CD, choosing network/wireless connection, without having to install any USB cables from the PC to the printer in the process. many posts in the forum mention having to connect USB cables in the wireless installation process.
Can I install the software in the same fashion on the other two laptops? Or, do I need to do something differently?

The USB cable is used on those printers which do not have display or front panel wireless setup is not possible. We configure the wireless settings during install and save those settings in printer's memory by transferring through USB cable. Therefore the USB is plugged in during wireless installation temporarily. In your case I don't think plugging in USB cable is necessary as the printer is already on network and had IP address. Connect the laptops on wireless network and proceed with regular install, the printer should be detected automatically.
Thanks
Naveen K
HP Support Engineering Center
Click on BLACK STAR button to say thanks
(Although employed by HP, I'm trying to address the issues with my sole willingness and my employer does not bear any liability for my responses)

Does the Xbox 360 wireless adapter even work with the WRT54G wireless router?!!? If so, how???

I just bought a WRT54G wireless router (Ver 8.0; firmware updated to latest). I have successfully connected my wireless laptop using WEP security, but I'm at wits end trying to get the Xbox 360 wireless adapter to work. (It worked just fine with my Netgear router until that router recently died.)
When I do the "Test Media Connection" routine (you XBox 360 users know what I'm referring to), the Xbox immediately recognizes the Network Adapter and indicates that it is connected to the Wireless Network, but it inevitably fails the next step in the process: IP Address. I have the set-up for the IP address to be assigned automatically by the router (which is set for DHCP Server enabled).
I have gone around the mountain innumerable times myself and then with well-meaning friends who say try this, try that, try this, try that. I've had to re-establish my laptop set-up so many times I wanna scream!
Are the Xbox 360 wireless adapter and the WRT54G even compatible? If so, what am I missing here? I'm not too technical and obviously in over my head, but this ought not be that hard.
Please, please do NOT respond unless you KNOW the answer! I don't mean to be curt, but I'm over / past "suggestions to try."
Thank you VERY much for your time and consideration if you can help me.

I don't think that the X-BOX adapter is not compatible to wireless rotuer .... there are few settings you can try on the router ... Access router setup page ... Please click on the tab "Application and gaming" and click on sub tab "Port range forwarding" 1) On the first line in Application box type in "Xbox", in start box type in 88, in end box type in 88, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 2) On the second line in Application box type in "Xbox", in start box type in 3074, in end box type in 3074, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 3) Now save the settings 4) Once you return to the setup page, click on the tab "Administration" and disable the UPNP and save the settings. 5) Now assign the given ip address on your xbox ip address :- 192.168.1.20 subnet mask :- 255.255.255.0 default gateway :- 192.168.1.1 Please assign the dns address on the xbox primary dns :- 4.2.2.2 secondary dns :- 192.168.1.1 6) Please try to test your xbox live. Hope it works ...

I recently bought a WRT54G wireless router along with a W...

I recently bought a WRT54G wireless router along with a WUSB54GC compact wireless adapter and set up both products as directed.I get a message saying connected to the access point but cannot find internet. While connecting to my internet directly,(using a fiber optic cable with no modem necessary)it connects to the internet however using the modem,wired or wireless it still gets the same error. I am not computer literate,so i don't understand abbreviations or where to go to input information into certain areas,so if anyone could help me with step by step information I would be very grateful. Thank you and happy holidays.

Let me know the Model number of the adapter & the operating system of the computer ......so that i can assit you further ... ..

New WRT54G wireless router. Who's the genius that can help me?

I just purchased a WRT54G wireless router. The main reason is my son wanted to be able to use his Sony PSP online. I also have two desktop computers that will be wired thru this router. My question's are. If he is using his PSP online and the desktops are wired, can the desktops be "hacked" if they are on/off? If the router is turned off then the wireless is not working? If I access the router and disable the SSID Broadcast then the wireless portion of the network is off? What are the safest security settings to protect my network?
Thanks.

Dead Mans Zone.... I guess.
Using the DMZ is a very simple and risky way to forward ports. The DMZ takes an ip address of a computer on your network, and forwards all ports to that computer. This is really nice if you are having problems forwarding ports for some program. It can be a life saver if your router will not allow you to properly forward ports. It also has a huge downfall. The computer that is in the DMZ is now wide open to internet traffic. Meaning that it will catch virii, and it will be at risk of being hacked. If you put a computer into the DMZ then please install a software firewall to help protect it
Orange/White. The Cisco logo is the Router’s SecureEasySetup button. It lights up and will stay orange when the Router is powered on. The color orange indicates that the Router is not using the SecureEasySetup feature, while the color white indicates that the Router is using the SecureEasySetup feature. When the Router enters SecureEasySetup mode, the Cisco logo will turn white and start flashing. After the Router has generated the SSID and WPA-PSK (also called WPA-Personal) key, the Cisco logo will stop flashing and stay white.
Message Edited by wehowardjr on 12-30-200611:26 AM

WRT54GS Wireless Router with Speedbooster.... I need help please!!

Similar Messages

Maybe you are looking for