WRT54GS WLAN LED light flickering with no wireless activity

I have a WRT54GS router. It is password protected. Even though I don't have anything connected wirelessly to it, sometimes the WLAN LED light flickers. Is there anything wrong? I checked the outgoing logs and I only see one I.P. address.
Message Edited by fadsunite on 02-11-2009 09:09 PM
Message Edited by fadsunite on 02-11-2009 09:27 PM

Thanks, I was worried that someone had managed to figure out my password and was accessing my router/internet connection illegally.

Similar Messages

  • Can WRT54G connect 2 XP laptops with different wireless cards, i.e. b and g,?

    My WRT54G router works fine with a lenovo windows laptop (Intel wireless 3945ABG card) and my dell linux box but it is not accepting my old T40 laptop which has a dual-band wireless a/b card.   The WRT54G box indicates this router accepts both b and g wireless cards. 
    Question is can this router  simultaneously  hookup these 2 laptops  or do I have to resetup the router in order for it to work on the T40?  
    as it is now, the wireless network shows on my T40 and it appears to 'take' the access key i input but then the T40 just 'hangs' trying to get into that network.   I have set the encryption key on the router to WPA. and i want to keep this.

    Make sure the computer that can't connect has DHCP enabled, Update the computer wireless card drivers, Check that the security you entered is correct.
    GoodLuck
    Matt

  • Wireless-B BEFW11S4 "wireless B" LED light...

    I'm trying to set up a wireless router with my DSL but I'm having a problem.  I followed the directions (plugged the cord from the modem into the internet slot on the router and the other cord from an internet port on the router to the computer) but the wireless B led light doesn not come on.  I tried pressing the reset button and yes, I did hold it down for over 30 seconds. Nothing happens. How do I fix this so I can get online using my wireless?

    are u able to go online with the hardwired connections ??? if so , get into the router using http://192.168.1.1 , go to the wireless section and ensure that wireless is "enabled"....or else the wireless part may be dead.

  • Wireless keyboard ERRATIC LED light

    I use an Apple wireless keyboard which sits about 12 inches from the iMac. The green LED light in the caps lock key behaves erratically. Sometimes the caps key is on but the light is off, some times the caps key is on and the light on. I have try re-parring the keyboard with the computer but the problem persists. I took the keyboard to the genius bar. The genius tested the keyboard with a laptop and worked fine. Has anyone had this issue? is there a fix to this issue?

    Hey, i came on here to see if anyone had the same problem i have just started having with my wireless apple keyboard. It turns out that the caps lock LED wont light up anymore but the keyboard still works how it should. Ill post back if it starts to have the same symptoms as your keyboard. How is yours now, have you resolved the issue?

  • Dimmer control for LED lights with HTTP Requests

    Hello,
    I'm al little bit know with LabVIEW, but I have a problem that I can't get fixed.
    For a project we control the led lights in a house with http requests (we use the http get request): this exists of a http address, the number of the light, the PWM (the brightness of the led) and the current.
    Controlling the lights with the switches is easy and is working fine. Now what we want to do is create a dimmer that can be controlled with the switches in the rooms.
    The following should happen: if the users clicks one time (so lets say for less than a second) than the light should just switch on. If he/she pushes the light switch and keeps pushing it than the light should dim.
    So the value of the PWM (and this is a string value) should change from 0 to (lets say) 100 when pushing it once, and it should decrease form 100 tot 0 (step by step) when the user keeps pushing the button. The thing I'm having difficulties with is making a difference between just clicking once and keeping the button pushed for a few seconds in the labview software.
    Any tips or ideas? Any Help is Welcome!
    Thanks
    CORE CVBA

    CORECVBA wrote:
    The thing I'm having difficulties with is making a difference between just clicking once and keeping the button pushed for a few seconds in the labview software.
    It sounds like everything else is working and your problem is to detect the button action details.
    Are you talking about a real physical switch or is this a switch on the LbVIEW front panel?
    All you need to do is detect a off->on transition, When it occurs, place the current tick count into a shift register, then subtract it from the tick count in subsequent iterations (as long as the button is TRUE). Change your output as a function of the elapsed time until the button is released.
    LabVIEW Champion . Do more with less code and in less time .

  • MAC LED lights three times with clicking noice after Software Update

    Hi all!!! I am a new Mac user.  As recommended i have been regularly updating my OS (software updates).  After updating, as mentioned, the MAC restarts.  But during restart it tries to restart three times (the LED light on the bottom right corner lights u

    I'm a bit confused here so I hope to clear things up in your post.
    You're Device is listed as Z10 (unless you've updated within the last 2wks of this post).
    Mac Desktop?
    - did you mean BlackBerry Desktop Manager for Mac?
    - or did you mean Z10 BB10 OS updated to 10.1? (which provider)
    If on Z10 you mean you updated to 10.1 I hope you're not using a leaked BB10.1 release (that's going to cause you nothing but issues down the road if you're not sure what you're doing, trust me i thought I did myself lol).
    Keyboard:
    Have you checked in Settings > Keyboard for any entries you custom added or shortcuts that auto correct? If you're not sure you can clear them ALL out, close your apps on your Z10 and retry say an email with a paragraph and see if that fixes it?

  • I have an iPhone 4 and the flash works great theirs just a little problem. Theirs times that it don't work... Anybody have an idea what it might be ? I resented my iPhone 2 but somehow it only flashes with the LED light from the notifications.

    Why does it do this and what can I do to fix it I want to use my light at all times

    I read the article thanks.   I tried the settings-general-reset-reset network settings-reboot system-go to wifi settings-select wireless connection-select the ">"-symbol-select auto for http proxy.   I was optimistic about that because I thought I changed some setting somehow to cause this problem, but it didn't work.  More specifically, I did connect successfully and browsed the Internet for a good while, but then I put down the phone for a minute, the phone went into sleep/power save mode, and when I picked it back up a moment later it was no longer connected.  Dang.   Had to select the connection and use my password yet again. 
    Another valuable bit of info for you.   The only network with which I have this problem is my home.   I use all kinds of devices at home and no other devices have this problem.  Also, I use this iPhone all over with various wifi networks at hotels and starbucks and family's homes with no issues whatsoever.  It remembers and automatically reconnects with every wireless network except the one in my own house. 

  • Problem with led lights. power light off and battey light on all the time

    I have a lenovo IdeaPad U310 Touch model 20222. Runs with Windows 8.
    I had this laptop for just 7 months and I've been having some problems with the led lights.
    The battery light is always ON (white light) even when the laptop is shutted down (start-power-shut down). Is not plugged in to the wall and still on.
    The power light is always OFF (no light), even when the laptop is on and running.
    how can i solve this?

    can you tell me when the issue started to persist?
    since you got it or after using for couple of months?

  • SORRY WRT150N Wireless LED light not on

    I purchased my WRT150N router almost 3 months ago and the first couple of times that I used it the wireless light and connectivity was fine but then I stopped using it for a while and now the wirless light will not come on and my laptop will not get a signal.  I have tried many things and there is no wirless connection.  I have a wireless adapter but it is not getting a signal.  Any help on what I can do to get the wireless led light on and get connection????  I really need help.

    have you tried powering the switch on or off? and still no light? have you already restarted you computer?

  • Does anyone have problems with the led light ?

    Does anyone have problems with the led light ?

    LOTS of people reporting a range of similar issues.
    https://discussions.apple.com/thread/6648856
    https://discussions.apple.com/thread/6574287

  • Dv3z black screen with caps lock and numlock led lights flashing

    dv3z boot with black screen and (screen) flashes every few seconds, cap and num lock led lights flashes every 2 seonds as well.  It boots eventually but takes forever.

    Hi,
    I your notebook still under warranty?  If it is, you will need to contact HP and arrange to have the notebook repaired under warranty.
    If you live in the US, contact HP Here.
    If you are in another part of the world, start Here.
    If you're out of warranty, I would suggest getting an estimate ( and a confirmation of the diagnosis ) from a local computer repair shop.  If the actual processor chip is faulty, this is far easier to replace than say a fault with the graphics chip ( which usually means a new Motherboard ) and so may well be worth the expense.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • I am having some problem with my battery, always at 99%, led light not work

    Hi,
    I just purchased my macbook 2 weeks ago. The battery was perfectly fine on the first 2 week. After fully charge, led light turn from amber to green as what it suppose to be.
    But since today, when I plug in my charger to my laptop, the led light wasn't on at all but based on the battery icon shown on mylaptop, it is charging slowly.
    I tried to unplug the charger and replug it in again. It turns to green ( while the icon shown 60%) and 3 sec later, the light off again.
    unplug-replug again, it turns to amber, a few sec the light turns off again. and it just keep on and off.
    I am a bit confused. I rang up apple helpline, they suggested me to reset the PRAM which seems work.
    restart my macbook. the charger turns to amber and charging till 99% and not turning green anymore.
    is that normal?

    This is a quote from the page I bookmarked for you to read. "The System Management Controller is an integrated circuit (computer chip) that is on the logic board of the MacBook or MacBook Pro. As the name implies, it is responsible for power management of the computer. It controls backlighting, hard disk spin down, sleep and wake, some charging aspects, trackpad control, and some input/output as it relates to the computer sleeping."
    The SMC used to be called the Power Managment Unit. I am surprised that apple did not have you reset this also.
    If the battery fall below 96% it will start a charge cycle. Have you callibrated the battery.
    It is hard to diagnose the problem till you try all the steps. Let us know how it turns out.
    Mort

  • HT1551 led light continuously flickers apple logo appears then no signal indicator   appears , how can I get back original  setting?

    Having trouble ,tried giving update and now the led light turns on and off continuosly  apple logo appears for a few seconds then the no signal indicator can someone how I can return the unit to its original settings?

    You will need to grab a micro usb cable and restore in iTunes
    http://support.apple.com/kb/ht4367

  • What does this LED light do? ;) Flashing home with an "A" letter :))

    Can you please explain why is this led light flashing? What does it mean? Thanks! )
    Solved!
    Go to Solution.

    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество
    Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
    PM requests for individual support are not answered. If a post solves your issue, please mark it so.
    X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
    I am not a Lenovo employee.

  • Show popup window with LED lights using SALV(factory method)

    Hello Experts,
    I need to add a button that when the user clicks it, a popup window will appear
    showing the meanings(legends) of the LED lights in my report. How do I do this guys?
    Thanks you and take care!

    Please check the program SALV_TEST_TABLE_COLUMNS and
    after setting up the values for ICON and showi it as in a popup  by
      data: gr_table  type ref to cl_salv_table.
        gr_table->set_screen_popup(
          start_column = 1
          end_column   = 110
          start_line   = 1
          end_line     = 20 ).
        gr_table->display( ).
    a®

Maybe you are looking for

  • Need to Find Total number of InfoPart form in our Web application

    Hello, We have to find total number of Infopath forms in our web application. IS there any Power sheell Scripts or anuthing which can output the Infopath Forms location and file count . Thanks Kundan

  • Can't get my 30" Apple LCD at full res with the MacBook Pro Retina

    Hey I've been through a lot of posts and I can't seem to find a solution. I have a 30" Apple LCD monitor but the highest resolution I can get out of it through the MacBook Pro Retina is 1280 x 800. Any suggestions? I have tried holding down option wh

  • How to get (OAAD tcode) employee photo into sapscript / smartforms??

    Hi! I need to insert the employee photo jpeg (from oaad) into an sapscript or smartforms. It's possible to do dynamically? (without file conversion) Thanks

  • BP User Defined Attributes -- Error

    Hi experts!! The customer i am working on needed some extra fields on the Accounts screen page, so i defined all User Defiened Attributes from 1 to 10 and added them from the Node MARKETING of the component BP_HEAD. When i try to save the Account (af

  • Dynamic Type Support (or in app text size)

    Hey Claudius! After perusing the reviews for you, a main request is gaining support for dynamic type. Or having the option to change text size in app. Some consumers are straining their eyes to see small text. After Changing my app to support Dynamic