WRT54GSV4 wireless router xbox live nat help

I need help getting this router to be open nat for xbox live.  I have tried everything in the book and i can only get a moderate nat.  Could someone help me with this please?

Who is your ISP ? If the ISP is DSL the,you need to convert the modem into the bridge mode to get your X-Box working.

Similar Messages

  • Xbox live nat help

    Hello all i need help trying to figure out a nat problem that i am having. I start out with a open nat on xbox live when i run the test but after running the test several times my nat will change from open nat to modrate nat for what reason i do not know but i need help trying to figure out how to fix this problem i am useing a wrt160nv2 router thanks.

    NAT issues are quite common in this type of setup. Check out this article from the Xbox forum: Strict or moderate NAT type. You will need to adjust some settings on the router to resolve the NAT error on Xbox Live. Enabling UPnP and port forwarding should do the trick. You can refer to the following article for more information about these workarounds: Resolving NAT type issues with gaming consoles through a Linksys router.

  • G4+Netgear wireless router+Xbox Live

    O.K, I have a G4 connected to a Netgear wireless router, I also have an Xbox that I wish to connect to Xbox Live, can I get the thing working with an Airport Express??
    or should I buy the microsoft wireless adapter?(If I could i'd rather buy the express)

    O.K, I have a G4 connected to a Netgear wireless
    router, I also have an Xbox that I wish to connect to
    Xbox Live, can I get the thing working with an
    Airport Express??
    No, in order to use the ethernet port of an Airport Express (AX) in this manner you need to use WDS and that is not possible with a Netgear router.
    or should I buy the microsoft wireless adapter?(If I
    could i'd rather buy the express)
    The Microsoft adapter will probably work.
    iFelix

  • Linksys WRT54GSV4 Wireless Router

    Hi
    I have a Linksys WRT54GSV4 Wireless Router with frimware version 1.06.1.
    I have a internet connection that can performe 100Mbit/s. But when i check my connection with "TP Test" I only get ~40Mbit/s. I do the test without the router and I get 80Mbit/s+.
    Why is that? How do I get the router to pass through the traffic at high speed?
    Thanks....

    I guess you should get the latest firmware 1.00.9

  • WRT160N V3 Two Xbox 360 consoles Xbox live NAT Resolution

    Has anyone found a solution to the NAT problems involving two xbox 360s connecting to xbox live using the WRT160N V3 at the same time?  I always get one that reads Open NAT (usually the 1st one to sign in) and one that gets the dreaded Strict NAT type.  I have read of various solutions yet many of them do not resolve the issue.  Any help is greatly appreciated!!

    You can try the below mentioned settings and check.
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
    On the set-up tab change the MTU Size to 1365 and click Save Settings...
    Click on "Administration" tab and disable the option UPnP and click Save Settings...
    Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
    1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
    2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
    3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
    4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
    IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
    5) Also assign the DNS Addresses on the Xbox
    Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
    6) Turn off your modem, router, and Xbox...Wait for a minute...
    7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...
    IP Address: 192.168.X.[last part of ip in your device]    e.g. if static ip given to the device was 192.168.X.10 get the last part and put that to the empty box.

  • Opening ports for my xbox live NAT type

    I need help on how to open the ports needed to successfully pull my NAT setting from "strict" to "open" on XBox Live. Those of you here that have it, probably know what Im talking about.
    The ports I need to open are the following: 
    UDP 88
    UDP 3074
    TCP 3074
    Ive tried already, but it didnt work. I think I did something wrong.
    Thanks

    Hi AEX,
    First thing you have to make sure is that, you have to assign a static ip address on XBOX like 192.168.1.10, with subnet mask of 255.255.255.0, and gateway 192.168.1.1
    Now Forward the ports you have to this static ip address, which you assign to your XBOX
    Also make sure you are running latest firmware on your linksys router. You can check from www.linksys.com/download , If it is not latest, download and update to latest version.

  • Linksys E3000 Wireless Router, Xbox 360, 5GHz and 802.11n

    Please could someone help - I'm tearing my hair out!!
    When I set up a 5GHz 802.11n or mixed a/n SSID, my XBox can't connect to it, even with security disabled.  It just says can't connect to wireless network.  It can connect to a 2.4GHz SSID as 802.11g (not n).  I've already reported the issue to Microsoft and also tried all the obvious things (I work with computer networks) and nothing works.  It can see the network after a scan and, if I disable security, it will even warn me that security is disabled, but it just can't connect.  Tried everything I can think of, including different channel widths, channels, USB ports and static IP configuration, to no avail.  
    Here are the details:
    Router firmware version: 1.0.04
    XBox version: Elite
    NIC: Microsoft Wireless N Network Adapter (black, two antennae)
    I've reported the issue to Micrsoft Support and they're not sure what the problem is either.

    Maybe it's a compatibility issue. You and this guy have the same issue. But I'm not sure if you guys have the same adapter. 
     http://homecommunity.cisco.com/t5/Wireless-Routers/Xbox-360-wireless-adapter-and-E3000/m-p/412201#M2...
    I don't work for Cisco. I'm just here to help.

  • WRK54G - Unable to connect wirelessly to Xbox Live on 360

    Hi, I recently purchased the Xbox 360 Wireless adapter to use to connect with Xbox Live, because in my new house a wired connection is not feasible. However, when I try to connect to Live, the 360 is not recognizing a wireless network. I know that the WRK54G has not received an official Microsoft Xbox Live certification, but is there a way to use this router to connect to Xbox Live wirelessly? Thank you.

    Xbox settings :-
    Please click on the tab "Application and gaming" and click on sub
    tab "Port range forwarding"
    1) On the first line in Application box type in "Xbox", in start box
    type in 88, in end box type in 88, in protocol keep it both, in ip
    address type in 192.168.1.20 and give a check mark on enable box.
    2)   On the second line in Application box type in "Xbox", in start box
    type in 3074, in end box type in 3074, in protocol keep it both, in ip
    address type in 192.168.1.20 and give a check mark on enable box.
    3) Now save the settings
    4) Once you return to the setup page, click on the tab "Administration"
    and disable the UPNP and save the settings.
    5) Now assign the given ip address on your xbox
       ip address :- 192.168.1.20
       subnet mask :- 255.255.255.0
       default gateway :- 192.168.1.1
    Please assign the dns address on the xbox
      primary dns :- 4.2.2.2
      secondary dns :- 192.168.1.1
    6) Please try to test your xbox live.

  • Wireless to XBox Live?

    I'm hoping this is the right forum and I apologize if it's not.
    I'm planning on buying a wireless router to hook up to X-Box Live. So I was wondering if there's a preferred router to pick up that'll be compatible with my eMac?
    Any help or info will always be appreciated
    eMac G4   Mac OS X (10.2.x)  

    Any Ethernet-compatible router will work on a Mac, as long as it's a hardware one.

  • I have a problem with my wireless router wrt54g. 360 help

    So, let me explain my setup. 
    wireless router wrt54g has 1 wire connecing a home computer to the internet
    Laptop is wireless
    I tried connecting my 360 to my laptop (with a wire)  and having a shared internet connection so that i could connect to the internet. 
    YET! when i connect my 360 to my laptop, it dissconnects MY LAPTOP from the internet. Weird phenomenon i know.
    ALSO
    whats nat? When i connect with a ethernet cable, it says this when i try to join a game

    this video was able to help me out
     http://www.youtube.com/watch?v=6NIyo2kJEG4

  • Perplexing Wireless Router Issue! Please Help!

    OK Guys and Girls, I could really use some help.  I have a wireless router Mod. WRT54G ver. 2.0, and yes it has the firmware upgrade. The problem that I am current having is this, my computer can connect to the router no problem, and  i  can access the settings too, but it will not let me access the internet at all. It's not the cable modem because I can hook up my laptop to it and get internet.  So in short the router isn't, for some strange reason, letting my computer access the internet but the router can access the web.  Please any suggestions are welcome. Thank you in advanced.

    Access the setup page of the router by launching an
    Browser and type on the address bar, 192.168.1.1 and press enter.
    When it prompts for the username and password, leave the username field
    empty and provide password as "admin" (Without quotes)
    click on ok.
    On the main setup page the ""Internet Connection Type"" should be
    on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
    button.
    Now click on the sub tab ""MAC address clone"".
    - Click on enable
    Click Clone & click save settings
    Check WAN Ip on Status page of router ....
    If getting Valid Ip .... try going online
    If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

  • Wireless router and base station help

    Hello fellas -- I'll really, really appreciate any help I can get with this, so thanks in advance for any advice given. Here we go...
    I purchased a MacBook (2.16 GHz Intel Core 2 Duo, 160GB hard drive, 2GB RAM) about two months ago. It runs Mac OS X Tiger (10.4.9). Previously, I had a Sony Vaio desktop in my downstairs bedroom, and an HP Pavilion desktop in my mom's office upstairs. I have Comcast "high-speed" cable internet service. Downstairs (where the Vaio was) I have a surfboard cable modem with three cords coming out of the back: 1.) a power cord (obviously); 2.) a cable cord that runs into the wall for internet service; and 3.) an ethernet-looking network cable. This ethernet/network cable would have normally run right out the back of the surfboard cable modem and into the network port on the back of my Sony Vaio, but in order to provide internet service for my mom's HP upstairs, the network cable went from the back of the surboard modem and into a D-Link wireless router that we bought. Another network cable then went from the D-Link wireless router into the network port on the back of my Vaio. This provided both my Vaio and my mom's HP with good, steady cable internet access.
    When I bought this new MacBook, it came with an AirPort Extreme card (no base station yet) that allowed me pick up on the wireless signal from the D-Link wireless router and this provided me with internet service. To connect to the internet, I would connect to the wireless network that my computer called "default." By this point, I had shut down and unplugged my Vaio, so it's out of the picture now -- the MacBook has replaced it. However, I left the surfboard cable moden and the D-Link wireless router plugged in, and this way I was able to connect to the default network wirelessly with my MacBook, and my mom was still provided with wireless service from the D-Link router on her HP upstairs. This worked great for awhile, until eventually this default network started getting rediculously slow and started disconnecting itself every 30 to 45 seconds -- literally. For this reason, I went out and bought an AirPort Extreme Base Station at my local Apple Store.
    First, to make sure it worked, I unplugged the network cable (the one coming from the back of the surfboard cable modem) from the back of the D-Link wireless router and I plugged it directly into the base station I just bought. In other words, I took the D-Link router out of the picture and plugged the base station directly into my surfboard cable modem. This worked great, and it's how I'm connected to the internet as we speak -- it's providing me with steady, fast service. Instead of connecting to the default wireless network that was slowing me down before, I now connect to the base station's network, called "Apple Network 2b1d46." There's only one problem, though -- it involved taking the D-Link wireless router out of the picture, so now my mom can't get on the internet with her HP. The solution seemed very simple -- instead of plugging the surfboard cable modem directly into the base station, I would plug the surfboard modem into the D-Link wireless router, and then plug that into the base station. I saw no reason why this wouldn't work, and I still don't, but for whatever reason, it didn't.
    This is where I need help. When I try to plug it in through the router like that, I simply can't get on the internet. Everything else works perfectly -- the surfboard cable modem's lights are properly lit, as are the D-Link router's lights. The Apple base station's status light is a solid green like it's supposed to be, and strangest of all -- when I open Internet Connect to check my AirPort status, everything is fine there as well. It says "Connected to Apple Network 2b1d46," which is the new base station network that I should be connected to, and under that it says "Connected to the internet via Ethernet," yet when I try to open Safari, it says "You are not connected to the internet," which is in direct contradiction to what Internet Connect is simultaneously telling me (that I am connected to the internet).
    I've tried alot of things to trouble-shoot this. I've tried FireFox and Opera, and they can't bring up any web pages either, so I know the problem isn't just with Safari -- it's that my computer just can't connect to the internet or bring up web pages, even though Internet Connect and everything else says that it's connected. I've also run the Network Diagnostics an uncountable amount of times, and all it can tell me, in all its wisdom, is that my internet connection appears to be working fine and that I must have spelled "www.apple.com" (my home page) incorrectly (it says the same thing about any other web page I try to open). I've ran the network assistant to create a new location, and it also gets the the end of the wizard and tells me that it can't connect to the internet. Finally, I've also ran the AirPort Utility multiple times and set up the base station in every possible way, but still nothing works.
    On that note, I do have one question. When you run the AirPort Utility and choose "Assist Me", at one point during the wizard it asks, "How do you connect to the internet?" Right now, remember, I have the D-Link wireless router taken out of the picture (the base station is plugged directly into the surfboard cable modem). For the answer to this part of the wizard, I chose the option that says, "I use a DSL or cable modem with a static IP address or DHCP." Obviously, given that I'm on the internet as we speak, this is working fine. However, if I bring the D-Link wireless router back into the picture and plug the base station into it (the router), and then plug the router into the surfboard modem, should I still have the same option checked (the one thats says I use a DSL or cable modem with a static IP address or DHCP), or by connecting through the router, should I change my answer to one of the other two options. The second option says, "I use a DSL or cable modem using PPP over Ethernet (PPPoE)." The third option says, "I connect to my local area network (LAN)." I've tried all three numerous times, and none of them work -- I still have the same problem getting on the internet once I connect through the D-Link router, but I thought I could at least find out which one is the right option so I could stop having to keep trying all three of them. Can anyone tell me which of those three options I should pick when connecting through the D-Link wireless router (cable modem with static IP address or DHCP, cable modem with PPPoE, or local area network).
    Sorry, I know that was a long one, but if anyone can answer the previous question for me and/or give me some general advice regarding my problem with getting the internet to work once I hook up the base station through the router instead of directly into the cable modem, I would appreciate it more than you can imagine.
    Thank you very much for your time and help.
    -- Andrew

    I am doing something similar. I have the WAN port on my Linksys 4-port wired router connected to my DSL modem. My G5 and G4 computers are connected directly to the Linksys LAN ports. My older Airport Extreme (flying saucer) is connected to another LAN port on the Linksys. I had to setup the Airrport as a bridge in this configuration. I did this by using the Ethernet LAN port on the Airport instead of the WAN port. In the Airport Setup Utility I said to connect using Ethernet. This seems to work for me.
    I also use manual IP addresses for everything but you will probably want to use DHCP.
    Cheers,
    -= Ken =-

  • WRT54G Wireless Router Problem. Need Help!

    I'll start with the basics of my situation and if more details are needed, I will provide to the best of my ability.
      I have a comcast cable internet connection.  I have 6 computers in my house. Two of them are downstairs (which is where our modem is.) The other four computers are upstairs.  All of these computers are Desktop computers with the exception of one laptop.
    My laptop (which is Windows XP) can pick up a random wireless signal from the room it is in.  I also found out a way to share the internet connection on the computer by going into the properties of my network connection and enabling internet sharing on it.  This means if I connect a network cable from my laptop to another computer, I can leech the connection from my laptop and have internet access on the other computer.  I also  had a switch that I used to connect the other 3 computers upstairs by means of the laptop.  The problem was, the laptop was using someone else's wireless connection in the area, and it wasn't strong enough to keep up a constant connection.
    I decided, if I can leech someone else's wireless connection, why not have my own.  So i recently bought WRT54G Wireless Router and set it up on one of the computers downstairs (because that's where the modem is).  It works fine as far as connecting my laptop to the internet from upstairs.  My laptop can access the internet through the connection I set up in the LELA program. 
    Here is the part I am confused about.  Everything is plugged in correctly as far as the router is concerned because the laptop can access the internet.  But when I connect an ethernet cable directly to one of my other computers (which are Windows Vista, but I didn' t have a problem with it previously when I was leeching someone else's connection), the connection drops on my laptop, and the other computer still can't access the internet.  A notice pops up that says its trying to identify the network, but it gives an error that says there is something wrong with the DNS.  As soon as I disconnect the ethernet cable connecting my laptop to one of the other computers, the connection is fine again on the laptop.  It's only when I connect the computers together that the connection drops. 
    I just don't understand why it wouldn't work when I created my own network if it worked with another network with no problem.  My whole point in getting a wireless router was to have a router within good range to keep up a constant connection on my other computers that aren't in range of the modem downstairs.  I just don't know where else to look.  I'm not sure if it can be fixed on LELA, manually through my wireless settings, or if it could be a problem with one of my computers' settings.  I've tried many different things and I'm not sure what else to do so any help is most definately appreciated.  I feel like I've tried everything.  I know it's possible because I've one it before, I just need the help because I'm not much of a networking person and I don't know what I should start with to make this work.
    Thank you to anyone who can help or even point me in the right direction.

    Access router setup page ...Click on the Wireless tab on the Setup page- Here Wireless Network mode should be mixed- Provide any non-linksys name .... Set wireless channel to 11- And wireless SSID broadcast should be Enabled and then click on "Save Settings" >>Now Click on the Sub tab under wireless > "Wireless Security" Change the Wireless security mode to WEP/WPA ...type in the key & click save settings .... >>>>Click on Advanced Wireless settings>>Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" Check the connection once again & see if it works or not ...

  • Xbox Live Nat problem

    Hi guys, I searched around the forum and did the port forwarding, Dmz, UPnP and all that other stuff and it still comes up as moderate. I am wondering if I am doing something wrong or it is because my internet provider is Charter which runs on a private server. -Matt

    Please click on the tab "Application and gaming" and click on sub
    tab "Port range forwarding"
    1) On the first line in Application box type in "Xbox", in start box
    type in 88, in end box type in 88, in protocol keep it both, in ip
    address type in 192.168.1.20 and give a check mark on enable box.
    2)   On the second line in Application box type in "Xbox", in start box
    type in 3074, in end box type in 3074, in protocol keep it both, in ip
    address type in 192.168.1.20 and give a check mark on enable box.
    3) Now save the settings
    4) Once you return to the setup page, click on the tab "Administration"
    and disable the UPNP and save the settings.
    5) Now assign the given ip address on your xbox
       ip address :- 192.168.1.20
       subnet mask :- 255.255.255.0
       default gateway :- 192.168.1.1
    Please assign the dns address on the xbox
      primary dns :- 4.2.2.2
      secondary dns :- 192.168.1.1
    6) Please try to test your xbox live.

  • Xbox live nat on moderate (HELP)

    My xbox is connected wirelessly to my m10 router. I cant get my nat to be on open its on moderate. How do I make it open?

    Hi
    devinbrar 
    and welcome to the community!
    I just saw this similar inquiry in this thread here "How to change Nat setting on valet so Xbox can function properly"
    Check it out!

Maybe you are looking for