WRT54GX2 Version 1 or 2? Firmware upgrade

I am having VPN problems with this router, and wish to upgrade firmware as first step in resolving this problem. How do I know which version?
Also, when I look at the available firmware downloads, neither version 1 or 2 firmware downloads show my current firmware 1.01.14???
What's up with this??
Thank you for your input..
Thorlane

Disregard. I was finally able to reach Linksys Cust Service via chat, and they stated that if NO version is indicated above the serial number on this router, than it is version 1. Also, ver 1.01.14 does not show up on firware updates is rather odd, and they said that it may have never been formally released, whatever that means.. Oh wellll.
Happy networking....
Thorlane...

Similar Messages

Download and Install RV180W Firmware Upgrade

I received a warning when I accessed the router site which indicated;
"Your connection is not private
Attackers might be trying to steal your information from 192.168.50.1 (for example, passwords, messages, or credit cards)."
I have downloaded the firmware upgrade. However, when I execute the file, it executes a command to burn file to my DVD drive.
When allow the command to proceed, window returns the following;
"The selected disc image file isn't valid."
Any suggestions on how to proceed with upgrading the firmware.

Hi,
Please follow the procedure mentioned below to proceed with upgrading the firmware
Upgrading Firmware
Cisco RV180/RV180W Administration Guide
Upgrading Firmware
CAUTION During a firmware upgrade, do not try to go online, turn off the device, shut down
the PC, or interrupt the process in any way until the operation is complete. This
process takes about a minute, including the reboot process. Interrupting the
upgrade process at specific points when the flash is being written to may corrupt
the flash memory and render the router unusable.
You can upgrade to a newer firmware version from the Administration > Firmware
Upgrade page. To upgrade:
STEP 1 Click Browse, locate and select the downloaded firmware, and click Upload.
STEP 2 (Optional) Check the box to reset all configuration and settings to the default
values. Do not check this box if you want to keep any settings you have changed
on the router!
STEP 3 Click Start Firmware Upgrade. After the new firmware image is validated, the new
image is written to flash, and the router is automatically rebooted with the new
firmware. Choose Status > System Summary to make sure the router installed the
new firmware version.
And then to reboot it
To reboot the router, choose Administration > Reboot Router. Click Reboot.
Regards
Aateek Singh
Network Engineer
Spooster IT Services

Firmware upgrade failed, printer now say i has firmware version 0. attention light lights up

Hey all
I had a problem printing a pdf on my mac, and then tried to upgrade my mac driver and printer firmware.
But the firmware upgrade failed for some unknown reason. And now the printer just have the ready and attentions lights on constantly.
I have tried to restart and reset the printer many times, and tried the HP firmware upgrade utility several times, with no luck. It just say it was "failed to upgrade"
Any idea what to do ??
My printer is a HP Laserjet Pro CP1025nw
Thanks
Jan

Hello Jan
It definitely sounds like the firmware update failed. Firmware is like a devices Operating System. Without it, it can't do much. This is backed by the "failed" message and that your printer reports it has version 0.
The printer will need to be serviced. Please call HP Phone Support at 1-800-474-6836.
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

How do i know what version of the Firmware Upgrade 1.01

Op
ps.
What i was trying to say is how do i know what version of the firmware does my player have installed on it,
I have a 28mb MuVo V200 and i was thinking of downloading the Firmware Upgrade .0.03 but i do not know if my player already has iMessage Edited by The_D_AUS on 05-0-2005 07:45 PM

Just access the player Menu and then scroll to the option 'Setting'->'Information'.
Jason

The firmware upgrade file is not supported on this hardware version MI424-WR Hardware Ver. C

Hello - I have been troubleshooting for quite some time a problem that only occurs on my wireless devices. 8 out of 10 times I fail to obtain a IP address from my MI424-WR. My connection to the device is successful, however, DHCP times out. I have connected to many other wireless routers in other locations in the last 4 weeks and have isolated my issue to my connection with my FIOS router. That is to say that when I am elsewhere I do not have this problem. I contacted support today, and the tech I spoke to was very nice and also clueless. What is the latest/current hardware ver of the MI424-WR Verizon is shipping? The tech said he could not tell me what ver the one he had in a lab was. If l log into the router under firmware upgrade I notice the message in my subject. I have had FIOS here with the same router since 9/2007. Any help would be apreciated.

That brings up something I have been curious about...could you see if this might work for you?
-First and foremost, log into the router
-At the top click Wireless Settings
-Go into basic security settings on the left and change the channel to 11 (yes, I know this doesn't work for all but please read on) and apply
-Now back on the left side menu choose advanced security settings, enter 802.11b/g Mode
---Honestly, most people should need G only by now, but choose what you need here (avoid mixed) and apply
-Go back onto the left menu and try advanced wireless settings again but this time choose "Other Advanced Wireless Options" at the bottom
-Change MTU to "manual" and enter in "1492" in the field it provides and apply
-Now at the top right go into advanced settings
-Click on the link for "System settings"
-In here UNCHECK the "Enable Logging" and "Low Capacity Notification" options and apply
I don't think they would be able to tell you which version is being shipped, because I am sure the new routers are coming with the new firmware and the old they send out first. But yeah, give that a shot and see if that does anything to help your wireless machines connect. I am kind of curious if that will change anything.

WRT310N v1 firmware upgrade versions

I have a WRT310N, apparently v1 since there's no version on the label and the firmware was a 1.x version initially. I've upgraded it a couple of times and it's now at 1.0.07-LS-HND. I've noticed there's now a v2 of this model. Is it possible to upgrade from 1.x to 2.x?

Well its not possible to upgrade from v1 to v2. Basically v1 and v2 are the Hardware version. If you have v1 hardware then you need to upgrade the firmware of your router with the hardware v1.

WRT54GS Version 5 Firmware Upgrade

I am confused as to how to update the firmware on my WRT54GS Version 5 Linksys router.
I went to the support section on here, but there are five different options of router firmware upgrade. I bought this a year ago and figure it needs the update, can someone help me?
The choices I found on here are:
    Upgrading the Linksys VPN Router's Firmware
     Upgrading the Linksys Wireless-G Access Point's Firmware
     Upgrading the Linksys Wireless-G VPN Router Firmware
     Upgrading the Linksys Router
     Upgrading the Linksys VOIP Router's Firmware
Which one would I want for this basic network router? The reason I ask is because my wireless Internet is constantly down. It won't work unless I do a hard reset of the router each time. It is annoying that I have to do this all of the time. I have never had this problem in the year I had it until six weeks ago. I have to reset it numerous times to get it to read the Internet and then go into the settings and rename it each time. Also, the router and my PC and my landlords laptop always connect through to the router fine, it is just the Internet causing problems.

Hi… you can use choice no. 4 which you’ve mentioned, enter the model number >> WRT54GS >> select version 5 and save .bin firmware file on computer and upgrade it according steps…

Creative Zen Touch Firmware Upgrade version 1.01

Hi Everyone,
Just to make you aware, a new Zen Touch firmware has been posted on our site:
<TABLE id=Table5 borderColor=#cccccc cellSpacing=0 cellPadding=3 width=540 border=>
<TBODY>
<TR>
<TD colSpan=2><B>Filename: </B><B>ZenTouch_PCFW_L4__0_03.exe</B></TD></TR>
<TR>
<TD colSpan=2> ZENT-FWARE--L4
<DIV id=ShortDesc>This firmware upgrades your Creative Zen Touch player for improved functionality.
<DIV id=Fixes>
<EM>Fixes:</EM>
Improves player functionality when the Random and Next buttons are pressed.
Resets the Custom EQ settings when resetting your player's settings.
Improves the display order of the Touch Pad sensitivity settings.
Improves the continuous playback of WMA and MP3 tracks.</LI>
<DIV id=Notes>
<EM>Requirements:</EM>
Microsoft? Windows? XP, Windows 2000, Windows Millennium Edition (Me)or Windows 98 Second Edition (SE)
Available USB port (version . or higher)
Creative Zen Touch installed</LI>
<EM>Note:</EM>
To install this firmware update, do the following:
Download the ZenTouch_PCFW_L4__0_03.exe file into your local hard disk.
Connect the player to your computer.
Double-click the firmware upgrade file and follow the instructions on the screen.</LI>
</LI></TD></TR></TBODY></TABLE>
Cat

'Thanks a million for the link, KokChoy-CL! You are now on my X-mas present list.
I have been using the .0.03 firmware, but recently I read http://forums.creative.com/t5/MP3-Players/Zen-Touch-Custom-EQ-Frequencies-Wrong/m-p/64205" and wanted to try out the .00.06 firmware. Comparing from memory and using custom EQ, lows and mids sound much more clear now while bass is a bit more on the light side.

Does each new ios firmware upgrade contain the features from previous versions?

Does each new ios firmware upgrade contain the features from previous upgrades?

Not necessarily.
Just like OS X, somethings may be removed.

Firmware upgrade crippled cp1025nw

LaserJet CP1025nw color: was working flawlessly
received email from HP 4/3/2012, recommending firmware upgrade to v 20120130.
ran upgrade 4/3/2012 from iMac, OS10.6.8.
got error: 'update failed'
print queue says 'printing', cp1025nw doesn't respond.
printer lights: orange triangle enclosed exclamation mark plus green semicircle
This means: fatal error, per the user manual.
manual instructs to turn off, unplug, plug-in, turn on. I did this several times.
printer lights still indicate: fatal error.
HP utility says: device status: unknown, service ID: unknown, FW version: unknown, driver version 2.0.20110727
                  tried to print configuration page: got error 'cannot establish two-way communication with the device'
                  printer and computer are connected with USB cable, (this cable / port communicates without issue to Epson inkjet printer)
Tried printing from Dell laptop: Latitude E6410 with USB cable: Windows XP professional, 2002, service pack 3.
                  has routinely printed from this computer previously.
error message in printer queue: 'error - printing',
Dell said 'found new hardware' tried to install with HP cd-rom
                  error message said 'the hardware was not installed because the wizard cannot find the necessary software'
ran the HP print diagnostic utility HPPDU.exe file from the Dell with USB cable: 'Everything checks out okay with your printer'
print test page: no response from the cp1025nw
What should I try next?

Since my last post I’ve retried the same troubleshooting described before, this time just from the PC. The result is still the same. Lights on the cp1025nw indicate “fatal error”.
Does anyone know how to put this printer into ‘bootcode’ mode? I’ve read about this in some other posts about HP firmware updates trashing printers.
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=...
and
http://www.fixyourownprinter.com/forums/laser/63535
Is there some combination of button presses that sends the printer into bootcode so it is ready to accept the firmware?
HP: How do you start up these printers when they are just manufactured to load the firmware?

PC Suite Issues after Firmware Upgrade of N73

Hi,
A new Firmware finally became available for my N73. The version number of this firmware is 4.0735.3.0.2.
After upgrading my firmware, every time I connect my phone via bluetooth or USB i get the "The connected mobile phone does not have PC Suite support installed" message. When I try the Help -> Reinstall PC Suite Support option, nothing happens on the phone.
I am able to view my messages via Windows Explorer (but they do not appear in PC Suite below the phone image), do a sync with Microsoft Outlook, sync with Lifeblog, etc - no problems. The only thing that does not work is installing applications via the Nokia Application Installer. Whenever I try to install an application, I get an "Operation Failed" error on the PC, and nothing happens on the Phone. I have tried installing various apps (fring, snake, Conversation) but all result in the same error.
I have tried this in Windows Vista (with latest updates) and on a clean install of Windows XP SP2.
Summary of my Configuration:
Phone: N73 (RM-133)
Product Code: 0542457
Firmware: V 4.0735.3.0.2
Operating System 1: Windows Vista
PC Suite Version: 6.85.14.1
Bluetooth Stack: IVT BlueSoleil 5.0.5.178
Operating System 2: Windows XP SP2
PC Suite Version: 6.83.14.1
Bluetooth Stack: Standard Microsoft Bluetooth Stack
Has anybody experienced similar issues? Can anybody help me? Any help will be appreciated.

I have never had such issues with my N73 - same firmware on three different systems. I have upgraded the firmware 4 or 5 times. The fact that your phone refuses to install via Application Installer makes me think that there is some issue with the phone itself - corrupted temp folder or something. If the problem irritates you too much, backup the phone and do hard reset (hold *, Green key and 3 while powering on).
Ericsson T10i -> Nokia 7110 -> Siemens C45, C55, M55, M65 -> Nokia 6131, N73, N82 -> HTC Wildfire, Desire HD -> Nokia Lumia 800 -> HTC Desire X -> Lumia 820 -> Sony Xperia SP -> Lumia 925 + Sennheiser CX 500
If I've helped, use the Kudos button to thank

No contacs after firmware upgrade on N70

Hi
I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
I did the upgrade again just to make sure that everything went OK with the same result.
Can some help or has the same problem?
Firmware V 5.0638.3.0.1 18-09-06 RM-84
PC Windows XP SP2
Nokia PC Suite 6.82.22.0
NSU 1.2.0en
Best regards
Chris

not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

Firmware Upgrade: p1102w, p1606dn, m1210 series, cp 1025nw

The following products require a firmware upgrade (FW older than 20130210 ) and re-registration with ePrint center for use of the ePrint feature. Please print a configuration page to see what version of firmware your printer has.
HP LaserJet P1100 Series
HP LaserJet Pro P1102w
HP LaserJet P1600 Series
HP LaserJet Pro P1606dn
HP LaserJet M1210 MFP Series
HP LaserJet Pro M1212nf MFP
HP LaserJet Pro M1213nf MFP
HP LaserJet Pro M1214nfh MFP
HP LaserJet Pro M1216nfh MFP
HP LaserJet Pro M1217nfw MFP
HP LaserJet Pro M1218nfs MFP
HP LaserJet Pro M1219nf MFP
HP LaserJet Pro CP 1020 Color Printer Series
HP LaserJet Pro CP1025nw
If a customer has one of the above devices, has FW older than 20130210 and has registered the device with HP ePrint Center, they will need to update the firmware on their device in order to continue to use the ePrint feature.
To obtain the firmware, please visit www.hp.com/go/eprint and do the following:
Select your device series from the list.
NOTE: Reference above list for help on finding your device series.
Select the appropriate operating system for your PC.
Click the RUN button.
Follow the on-screen instructions to download and install the firmware upgrade for your device.
After firmware upgrade is complete, you may need to reset Web Services on your device and re-register the device with the HP ePrint Center by doing the following:
Access the Embedded Web Services (EWS) by entering the IP address of your device in your web browser’s address bar.
Click on the HP Web Services tab.
Click the button to remove Web Services.
Click the button to enable Web Services.
Print the information sheet to get the new ePrint printer code for your device.
Go to www.hpeprint.com
Sign in to your ePrint account.
Select “Add a Printer” to your Account.
Enter the new printer code for your device (from the information sheet).
10. Enter a new customized email address.
NOTE: Your previous customized email address may be unavailable. If that occurs, please choose a new customized email address or enter your old customized email address and choose from one of the suggestions presented.
11. Change your ePrint settings as needed.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

@jrboozer,
Have you tried going into your Start menu, looking for the HP folder, then using the wireless configuration utility? When I set the wireless up on my machine, this was how I did it and it worked beautifully.
Please let me know if you need any other help.
I am an HP employee.
Say Thanks by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as Accepted Solution

Firmware upgrade, then lost

Hi,
Quickly following automatic firmware upgrade on 1 week old Time capsule, network is now lost. Airport set up utility can't find Time Machine .. others experience the same problem? TM feels hot .. perhaps overheated due to firmware upgrade. Solutions welcome.

Your computer came with OS 9.0.4 installed. OS9.1 is required for Classic so is handy to have, and apparently your firmware installer requires 9.2.1 You can use free updaters to update to any later OS9 version from any earlier one.
I don't see any option but to obtain a used copy of OS9. Make sure you get the gold full retail version rather than a machine specific version since the latter will only work in those computers for which they were designed. You can get away with a machine specific version as long as it exactly corresponds to the model and build of yours, but that is often hard to confirm until too late in the purchase.
Note that any drive you want to use with OS9 either for purposes of installing OS9 or for running software will have to have OS9 drivers present on it. These are installed when you format a drive and cannot be installed later without reformatting the drive (and losing everything on it). If your computer still has its original drive then those will likely still be on there unless you reformatted the drive with OSX and did not select the keep OS9 drivers option (there's no harm in doing so and it saves a lot of trouble for doing exactly what you are trying to do). You can can have a drive present that doesn't have the drivers but it simply won't be seen by OS9.
Disconnect all third party hardware (including PCI cards) when updating the firmware.
Message was edited by: Limnos

Firmware Upgrade now no file sharing

I recently installed a firmware upgrade on my E3000 to firmware version 1.0.04.build 6. Since the upgrade I am unable to see any of my files on my network computer which is running windows 7. Before everything was fine and I could stream to my dvd players and dish receivers. I've tried everything I can think of to fix this problem. Any help would be greatly appreciated.
Thanks in advance.

Hi Mr. Bernard,
Thank you for your question.
However, the Small Business Support Community is limited to Cisco Small Business Products and the E3000 is not a Cisco Small Business Product.
Your question below relates to a Cisco Consumer Product which our community would not be able to help you with.
The best area for you to post your question would be at the Linksys by Cisco community: http://homecommunity.cisco.com/community.
Regards,
Diego Rodriguez
Cisco Small Business Community Engineer

WRT54GX2 Version 1 or 2? Firmware upgrade

Similar Messages

Maybe you are looking for