Wrt54gx4 configuartion issues

The setup cd was too damaged to run so I've attempted manual. First wireless or networking attempt ever. Everything is conected and have pinged it sucessfully. When attempting to connect to http://192.168.1.1 connection fails. I also disabled firewalls and can't get in. My computer see's the linksys but it's not configured. Don't have any protection, it's open.
Frustrated.

Hi …….
Well in this case, where you are unable to log into the setup page of the router then first reset the router by holding and pressing the reset on the back panel for 30seconds.
Then try to log into the setup page of the router with http://192.168.1.1 username leave blank and the password is admin. If this still does not works then try to log into the setup page of the router from the start > run > http://192.168.1.1 .
If you are still unable to log into the setup page of the router, then try the same thing with a different Pc.

Similar Messages

"Cannot perform operation, connection is closed" with Open MQ 4.4

I am using Sun MQ 4.4 with Glassfish 2.1.1 on Red Hat 5.7.
I am able to install glassfish cluster and all the instances are running fine. But, when I try to send a message to a topic, I get following exception
javax.jms.IllegalStateException: [C4062]: Cannot perform operation, connection is closed.
at com.sun.messaging.jmq.jmsclient.ConnectionImpl.checkConnectionState(ConnectionImpl.java:2468)
at com.sun.messaging.jmq.jmsclient.XAConnectionImpl.createSession(XAConnectionImpl.java:105)
at com.sun.messaging.jms.ra.ConnectionAdapter.createSession(ConnectionAdapter.java:383)
Following is part of the stateless EJB where I am creating the session.
@PostConstruct()
private void init() {
if (connectionFactory == null) {
if (log.isTraceEnabled()) log.trace("Connection factory not set. Retrieving from server context.");
InitialContext ic = new InitialContext();
connectionFactory = (ConnectionFactory) ic.lookup("jms/testConnectionFactory");
if (log.isTraceEnabled()) log.trace("Creating JMS connection.");
connection = connectionFactory.createConnection();
@WebMethod()
public void send(){
Session session = null;
session = connection.createSession(true, Session.SESSION_TRANSACTED);
I am trying to install these on a couple of new machines. Same application works on other machines so I am guessing this is a configuartion issue somewhere on these servers.
My question is what would be a good way to find the cause of this failure.
I have turned on log level to finest for ejb-container, jms, RA through glassfish Admin console, but no useful information.
Also, I don't have the name of the servers in DNS yet. I am using IP address for specifying instances.
Any suggestions ?
Thanks
Vineet

Hi Tom,
I used the demo/helloworld/helloworldmessage.java sample.
By the way, I should add that the broker log contains lines like:
[B1066] Closing [email protected]:2461 because "[B0061]: Client exited without closing connections"
Is this what one would expect for a connection.close() ?
It almost seems that this is happening only when the connection is nulled explicitly or the connection object is destroyed.
One last thing:
I was led down the garden path. The reason for the server being thread starved was that there were indeed connections not being closed/nulled.
Thanks in advance,
Patrice
Edited by: paubry04 on Sep 13, 2007 8:21 AM

WRT54GX4 issue

My company currently has a WRT54GX4 for the laptops as a replacement for a now completely failed WRT54g v1.0. I've read some issues about internet connectivity dropped but this is different. My WRT will stay connected but drop to 5.5mbps with excellent signal. Once in a while the connection will drop and come back but mostly it just stays at 5.5mbps. What is weirder is that one laptop is usually used less than 20 feet from the router and still drops to 5.5mbps and stays there until the connection is repaired and then stays at 54mbps for only a minute at most then starts falling back to 5.5 slowly. The Firmware is 10.00.17, the Beacon is set to 50, Its hardset to Chan 11 and the RTS and Fragmentation are both decreased by 40 and I still get the exact same issue.
All laptops have internal 54g adapters so none of them are SRX enabled but should still work. we have a printer/fax on a 802.11b jet direct and a WPC54G installed into one desktop with a PCMCIA/PCI Adapter and everything sees the exact same issue. Some help would be great since the original WRT54G is now completely out of service and we are solely reliant on the SRX400 for all our wireless.
Churchlight IT Dept.

First of all, I only meant to suggest that you turn off the wireless B devices temporarily, just to see if this corrected your wireless problem. I didn't intend for this to be the permanent solution to your problem.
If turning off your wireless B devices corrects your wireless problem, then there are two more permanent solutions to your problem:
1) Since you already have an ethernet wire for the workstation, and it is located near the printer, simply install a 5-port switch (for example, the SD205) on the end of this wire. Then wire the workstation and the printer to the switch. (Note: this assumes your printer has a 10/100 port.)
or
2) Get a wireless G print server (for example, the WPS54G), and connect it to the USB port on the printer. (Turn off the wireless - B). This would convert your wireless B printer to a wireless G printer.
Hope this helps.

WRT54GX4 and Mac OS X DHCP issue

Hi,
I am using WRT54GX4 router connecting wireless from an iBook G4 with OS X 10.3.9. I connect just fine as long as I configure TCP/IP "Using DHCP with manual address".
I cannot connect if I switch to straight DHCP. In the Network Preferences window under Network Status, the Airport connection shows yellow.
Thoughts?

ensure that the router has the latest firmware .. if not , then upgrade it first .. reset and reconfigure the router after the firmware upgrade..
if still the same issue , i guess u might need to update the drivers of the wireless adapter..

WRE54G - WRT54GX4 - Issues!

I have had this range expander for approximately 4 years now. It works, I mean blue lights and all and I can connect to it, but I could never access the web utility. I tried to plug it into the router, results in a lost connection. Tried changing the IP to static, but, changes me from network 2 to network 3, looses connection, then wants to repair it back to DHCP. This was all done on the wired computer. Running windows 7.
On the wireless computer, plugged it in to the ethernet port on the back of the computer, changed the ip to 192.168.1.5 and dns to 68.87.77.134, somehow, got to the setup page for the utility, but that's it. As soon as I tried to change any settings, I lost connection. I don't know what firmware version I have cause I can't access the utility. The expander is version 3. The firmware on my router is up to date.
Any help anyone could pass along my way would be greatly appreciated.
Thank you all so much.
Rebster

Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your Expander, wait for 30 seconds and re-connect the power cable...
Connect your Expander to a computer, click on the Start button >>> Settings >>> Control Panel >>> Network Connections - Right click on the icon for Local area connection and go to properties- On the 'General' tab select 'Internet Protocol TCP/IP' and click on the Properties button- Select 'Use the following IP address'- Provide IP Address - 192.168.1.5, Subnet Mask - 255.255.255.0...Click on Ok button to Save and Click on "Close" on main Properties window...
Now open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.240. Leave the Username blank & in Password use admin in lower case...It should open your Expander set-up...

Issue with Payroll posting in FI

Hello Friends,
our company run a simulation run on payroll for the month of Jan 2008.
things are perfect.. but after actual the posting of payroll, the posting is not correct.
for example.. simulation run shows the total payroll value is 1 million $.. but actual run posts only half a million.
Is there any way I could find employees payroll which is not posted in FI..
how to find a solution for this issue..
Thank U for Ur time..
Cheers
Senthil

What do you mean by: "a simulation run on payroll " - is this:
a) A payroll Simulation
b) A Simulation of the Posting
If (a) then the Posting only runs on actual (ie updated Payroll Results).
If (b) then check the errors in the simulation run and the update run.
Note that there are several settings for the Posting Run:
"P" => Live Posting - this will only post if there are no errors
"S" => Simulated Posting will do everything (ie up to and including creating documents, but will not Post.)
"T" => Test Run this only does basic posting and, basically will only check that your configuartion has no "out of balance" postings It does not check Account allocation etc.

IMac will not get a good connection to Linksys WRT54GX4

I've seen similar reports as this, but nothing exactly like it, so I'm not sure if its the same problem or unrelated. I've got this Early 2006 20" Intel iMac. It will NOT connect correctly to my Linksys WRT54GX4 SRX400 Linksys router. It seems to work fine for a bit, but then I the connection deteriorates. I have a Macbook that has absolutely no problem.
The iMac connects to the network about 50 percent of the time. Sometimes it just says there's an error. When it does connect it works fine for a bit. The signal strength is great, and I can stream movies in iTunes to my Macbook. I don't know what causes it, but 15 minutes later or so, the signal strength is only showing 2 bars (the router is literally 20 feet away with no obstruction), and iTunes sharing of movies no longer works. This is crucial to my setup in my house, as I'm using the macbook as a faux AppleTV to watch movies on my TV that are stored on my iMac.
What's odd is that the macbook works perfectly from even further distances, as well as some of my roommates Windows PCs. And they work indefinitely. I noticed in the system profiler that the iMac and the Macbook have different Airport Card information. The iMac says it has Broadcom firmware, the Macbook just lists a version number.
Is Apple working on patching this?
If not, would I be able to get Apple to install a newer Airport Card in my iMac?

Welcome to Discussions, MikeCP66!
You ask "Is Apple working on patching this?" to which the answer is that the patch has been successfully completed. It is AirPort Extreme Update 2007-002 plus the 10.4.9 Update, and this appears to have corrected the wireless issues of most iMac users, both Core Duo and Core 2 Duo.
I'm assuming that along with your up-to-date OS 10.4.9, you also are up to date with iMac firmware (Boot ROM Version in System Profiler), SMC firmware (SMC Version), and with AirPort Extreme Update 2007-002 recently installed.
I'm also assuming your Linksys firmware has been verified to be up to date. If you're uncertain about what I'm referring to in any of this, please ask. The Linksys and both Macs must all be set for using the exact same type of encryption, of course with the exact same network name and password.
If all the above is ok, power down your computers. Power down and disconnect your Linksys. After a minute, reconnect your Linksys and power it back up. Power your Macs back up and turn on AirPort in both, using the menu bar icons.
Open the iMac's Network panel of System Preferences. Change the "Show:" selector from "Network Status" to "AirPort" and also click "AirPort" in the menu bar of that pane.
Set the "By default, join:" selector to "Preferred networks" and delete ALL networks from the list. Click the "Apply Now" button at the bottom right, after which no name should appear in that list.
Click the "Options..." button, set the "If no preferred networks are found:" selector to "Keep looking for recent networks" and uncheck the box "Automatically add new networks to the preferred networks list."
Click the blue "OK" button, again click the "Apply Now" button, and close System Preferences. Restart the iMac. AirPort will still be turned on, it will see your correct network name, although it will not be connected to any network.
Open System Preferences to the Network panel and go to "Show: AirPort" and again to the "AirPort" pane. Click the little + box and in the drop-down box select your network's method of "Wireless Security" followed by entering the network name and password.
Click the blue "OK" button, then the "Apply Now" button at the bottom right.
Your iMac's AirPort icon should shortly darken, indicating a connection, and checking it AirPort should be connected to your network, and should stay connected the same as the MacBook's does.
If not, until proven otherwise, some speculation might be suggested to Apple that the AirPort Extreme card within the iMac is not properly connected.

Issue on Deployment of AXIS framework in PI 7.0 Server.

Hi Experts,
We have a requirement of Using AXIS Framework in Receiver SOAP adapter in PI 7.0.Moreover we need USERNAME token with PasswordDigest.We have deployed aii_af_axisprovider.sda file in PI server with all relevant .jar files.However when we are checking the url http://host:port/XIAxisAdapter/MessageServlet its showing following optional components are missing.
1)XML Security API
2)Apache WSS4J
3)Apache Addressing
However we have used wsdl4j-1.5.1.jar file.We have added entry for wsdl4j-1.5.1.jar in provider.xml as well.However it still showing warning that optional component is missing
Could you please let us know which version we need to deploy for Apache WSS4J in PI server or do we need to do any other configuartion apart from above configuration so that to enable the UserNameToken security with passwordDigest.
Thanks in advance.
Regards
Nilesh.

Hi,
Post the answer for your issue, so that others can have!

File to RFC Issue

Hi All,
I am doing a File to RFC async scenario. I have done the related development in ESR and ID. While testing the file adapter picks the file does the required content conversion and is successful . When I check the RFC adapter it also shows successful. But the problem is the payload is the same as it was in the sender adapter. I mean after mapping the payload must change to the target message. Somehow in the RFC adapter I am seeing the same source payload. I deleted the Service interfaces, deleted the channels, deleted the ICO and recreated everything again but still the same issue. Can someone please provide inputs on the same. All configurations look correct. Ideally the message has not reached ECC but atleast the payload conversion should have happened.

Hi Amit
Check the log in message monitoring and see whether the operation mapping has been called or not.
Also with the default configuration we can only see the payload before mapping in RWB.
If you need to see the payload after the mapping then you need to add the below entries in NWA
Goto configuartion-->infrastructure-->Java system properties--->services
Choose the service XPI Adapter:XI and change the below property
Then once you open the message in RWB, you see one more entry with AM which will show the payload generated after mapping.

WRT54GX4 - variable router DL speeds

I think this problem has been going on for months, but it really only became noticeable when I started using Xbox Live. Basically, I have a WRT54gx4 (with the latest firmware, 1.00.20 I believe) with UPnP enabled, all xbox live ports forwarded; wireless MAC address ID filter.
The problem occurs like this - my wireless router DL speeds may be approximately close to my wired modem speeds (~ 5 Mbps) (Note: the upload speeds are always fine) for a couple of days (~4-5) on all my computers on my wireless network, and then for some odd reason will crash to subpar speeds 1 Mbps for all my computers and I'm pretty sure the Xbox as well (which uses the Microsoft adapter).
The effects are most noted when online gaming as playing with a 1 Mbps connection is challenging if not impossible. This 1 Mbps connection will remain constant for ~2-3 days (despite restarting the router) before returning back to 5 Mbps. During all this time, my wired modem connection is fine, meaning my ISP is fine.
I'm pretty sure this problem has existed prior to getting Xbox Live, as I have noticed slow periods of internet, but I never bothered to investigate it until now. I am also aware of the P2P programs and I'm pretty sure this is not the issue in this case.
Any help / information would be appreciated.
Message Edited by LightsEternity on 02-09-2008 12:36 PM

Hey Gollum, I've already mentioned that my router's firmware is the latest (1.00.20 on the Linksys product website). Reducing the MTU won't be possible, as XBox Live no longer works at 1350

External List Management - Issue in File Upload and Map

I am facing problem while maintaining external lists through ELM and executing step upload and map file for a tab separated text format file.
The file data is getting shown properly in file preview through mapping format but when I execute it through external list the data is not getting uploaded at all.The log is not showing me any error or reason for the same.
I want to know apart from basic ELM config, is there some other configuartion required to enable ELM to upload and map the file in turn.
Message was edited by:
Pratyasha Shishodia

I got the resolution to this answer.
The issue was the task under ELM workflow was not marked for background processing and hence it was always in ready state and never proceeded ahead thru ELM transaction.All the steps due to this reason were shown in planned or ready state.
There was no error in ELM as everything in the system had no issues and hence nothing came in error log.

Back to my Mac with LinkSys WRT54GX4

Verizon FIOS at home with Linksys WRT54GX4 UPnP enabled in front of Mac Pro. No issues with BtmM on the local LAN or WLAN (shares & screen sharing) from Mac Book Pro. Feature is enabled on both with the same .Mac account. iDisk and sync to .Mac both work on the machines.
Any clues to why BtmM doesn't show either host when away from the LAN/WLAN?
Thanks!

A little more information...
On the Mac Pro, I did a fresh install from scratch on a clean disk, then used the migration assistant only to move my user folder. All apps re-installed from media/downloads. On the MacBook Pro, I did a full backup to an external drive, then used the migration assistant to transfer all apps and user settings.
On the Mac Pro under the 'SHARED' section of the side bar, I see only my MacBook Pro. On the MacBook Pro, I see 'All', then I can browse to find my Mac Pro. This to me seems to be the problem. The MBP has been used on a windows network at the office in a Windows 2003 AD setting. I wonder if somehow this is the problem.
TIA for your help!!!

Help Understanding Loss Of WiFi Issue

Hello,
I am running into a stange issue. I am trying to help my neighbors with a wiFi issue. They have a cable modem BEFSR41 v3 and a WRT54GX4. Everytime there is a power surge or outage, they loose internet and have to usually reboot both modems. The BEFSR41 is the DHCP, I have the DHCP turned off on the WRT54GX4. This time the BEF** kept the internet going and the WRT** lost the internet and we had to reboot it to get connection again??
I never loose internet after a surge or power outage when it returns. I am using the same BEFSR41 v2 and a ONQ WL-330gw wireless access point. I never have to reboot, internet always comes back after outage.
I am lost on trying to figure out the issue for reboot at my neighbors when I do not have to at my house? Could their cable modem be bad?
Thanks JR

Try to upgrade/re-flash the firmware on your router.
Connect the computer with the Ethernet cable to the router.
Download the latest firmware from Linksys website and save it on your computer. Open the setup page of the router. Click on Administration tab and go to Firmware upgrade sub tab. Browse the firmware file that you have already downloaded and upgrade it on your router.
After upgrading the firmware on the router, it is recommended that you should reset the router and reconfigure it. Press and hold the reset button on the router for 30 seconds. Release the reset button and wait for 30 seconds. Power cycle the router and reconfigure it.
Also try to change some advanced wireless settings on the router. Click on Wireless tab and go to Advanced wireless settings. Change the Beacon interval to 75, RTS threshold to 2307 and fragmentation threshold to 2306. Save the settings.

WRT54GX4 SRX400 Connection keeps dropping

hey guys. i need some help.
I have the WRT54GX4 SRX400 router and for some reason, the wired connection likes to drop out every now and then and I don't know why.
Other than wireless security and router security, all settings are default. I also have the 1.00.20 (newest) firmware.
I can best describe it as this. I have AOL Instant Messenger running the background whenever I'm doing something. It likes to lose connection and sign off but immediately after several seconds reconnects.
Same thing happens when I play games online. I would be midgame on COD4 then a Connection Interrupted screen would pop up and I would lag for up to a minute before going to normal. I don't know if this affects my other roomates. My PC is connected by a 25 ft cable Cat 5 Cable. COuld it be that there's loss in the cable because it's too long/not CAT6 or the router is not strong enough to push the signal all the way through? I have Optimum cable and just had it repaired because we lost service for a day and know that is not the issue.
We used this router in my home home until my dad upgraded and it sat in the basement and never had this issue
Any help = appreciated.
Thanks!

First you need to make sure you are facing the same problem on your other computers? If its a problem only with your computer, then it might be the problem with your computer itself. In this case you need to change some settings on your computer i think this might solve the problem.
Click on Start - Control Pannel - Network Connections - now right click on Local Area Connections and click on Properties and below the General Tab you need to click on "Configure" and click on the "Advanced" tab under "Properties"you need to select "Speed and Duplex" or "Links Speed and Duplex Mode" and under "Value" change it to "10MB Half Duplex" and click on Ok. Once you make this changes on your Computer i think you shouldnt face that problem again.
If you are facing the same connectivity problem on your all other computers, then it might be the problem with the Router itself. Open an Internet Explorer browser page on a computer hard wired to the router...In the address bar type - 192.168.1.1...Leave the Username blank & in Password use admin in lower case...
Below the Setup tab you will find MTU, which will be set to AUTO so you need to change it to Manual and change the Size from 1500 to 1365 and click on Save Settings. This might solve the connectivity problem on your wired computer.

WRT54GX4 RF links die

I have one of the early WRT54GX4 (V1.0) which has been running 24x7 since installed on 3/15/06 with no issues up to about 1 week ago. Currently it's running 1.00.17 Firmware release (dated 4/30/2006). The client NICs are SRX400 - WPC54GX4 - 1.0, WMP54GX - 1.0 and a D-Link PCI adapter (a leftover froma D-Link system I trashed because of poor WAP reliability).
Suddenly about 1 week ago the netwrok had a short episode where the all the wireless links went down. All links failed. I rebooted the WRT and things came back up. Then 3 days later all links went down again but rebooting didn't fix the problem. I've re-flashed the firmware but still the wireless side will not connect. I've reset the Pass-phrase in all the clients and the WAP. I've checked the configurations (infrastructure). I tried switching to clients to Ad-Hoc and they would connect for a short period of time but then they'd disconnect. This continued to cycle. (I've never used Ad-Hoc so I'm not really sure of what to expect.) The wired connections work fine, the router portion works fine, DHCP works fine, connection to the WAN is 100% solid.
When I look for WAPs using the "Monitor" I can see it and the signal strength seems to be about what it was before the probalems (92%). The strange thing is that I don't see as many other WAPs as previously and it is the same on all the clients. (Not sure if this is related.)
Unfortunately, I don't have access to the RF toys I used when I put my original Proxim wireless in 12 years ago so I'm kind of working blind.
I recall seeing a comment someplace (on another forum) that the early WRT54GX series had a reputation for the power suppy (wall-wort?) going south.
The unit is still under the limited warranty and I could easily send it for a look see but since the wired side of the router is working and it is part of my home-office I'd really like to get some outside opinions. (I'll have to go buy something to put in its place while the WRT is out getting blessed.)
Any ideas would be appreciated.
Thanks.

hi , you can try and change a few wireless settings on the router before you send it back
access the router using http://192.168.1.1 "admin" is the passowrd...
go to the wireless section and select channel 11...save settings....now go to the advanced wireless settings and reduce the beacon interval to 50 , also reduce the RTS and fragmentation threshold by 40 each.....save settings...
try and connect to the wireless network now and then observe.

Wrt54gx4 configuartion issues

Similar Messages

Maybe you are looking for