WRT54GX4 Wireless link not working

Hi all
I have been trying to setup a WRT54GX5 Router but I've not been able to make the wireless link work.
The wired connections work perfectly but my laptop cannot see the wirleless network.
I've upgraded the firmware to the latest version available at Linksy's site 1.00.20
In the Status/System Performance page of the configuration the Connection status for wired is "Connected" but the wireless is always "Down".
In the Wireless/Basic Wireless Settings page the Wireless Network Mode = Mixed.
Also the "Wireless" LED in the equipment is off. It just lights up briefely at powerup (so, the LED is OK) but then remains always off
I've rebooted the equipment a number of times but to no avail
Any suggestion, comment most welcome
Thanks in advance
RL

Hi
Thank you for your post
I've just set the option Wireless Network Mode = Mixed in the Wireless/Basic Wireless Settings page of the configuration tool.
Could you please elaborate on how to enable the wireless option.
Best regards
RL

Similar Messages

  • Keyboard wireless key not working after upgrading to windows 8.1

    Hello,
    I am having hp pavilion dv6-6165tx notebook, where keyboard having a wireless button that turns ON and OFF all wireless devices, After upgrading to windows 8.1, HP Connection Manager is not getting installed, as well as Key is not working, key color turns red and white but no action is performed.
    Kindly suggest me some solution.
    Note: HP Doesn't provide drivers for windows 8/8.1 ONLY WINDOWS 7 for hp pavilion dv6-6165tx.
    Thanks.

    Hi @Jayesh_Bhadja ,
    Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion dv6-6165tx Notebook and the Wireless keyboard not working correctly. Here is a link to troubleshoot the keyboard.
    The HP Connection Manager is something that is for Windows 7 not Windows 8.1. I would uninstall this from your Notebook.  Here is a link to the HP Support Assistant if you need it. Just download and run the application and it will help with the software and drivers on your system that need updating. It has a troubleshooting tool in this.
    Make sure all your updates have been completed. I would try restarting my Notebook a few times.
    If that does not help I would uninstall the keyboard from the Device manager.
    Thanks.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

  • Adobe Edge links not working

    Yeah I have also experienced links not working when I import my .oam file from Adobe Edge Animate also. Is there anything the Muse team is doing to fix this issue? I need a response from you guys by the end of the week. my company website is malfunctioning due to issues with your software. If there is some sort of hotfix please let us know.

    When you install the software illegally, using a volume license, there is a script you can run that will enter all of the adobe servers into your local DNS hosts file so the software can be activated. This makes accessing those domains impossible. This scenario fits the description of your issue, not suggesting anything beyond that.
    The hosts file is in /private/etc/hosts and can be accessed through the terminal:
    sudo nano /private/etc/hosts
    If you see a bunch of adobe servers in there, that is your problem.

  • Add new document link not working in upgraded sharepoint 2013?

    Hello there,
    Upgraded SharePoint team sites from 2010 to 2013. add new document link not working for shared document in upgraded sharepoint 2013?. it is specially not working on machine where Office web apps set up with this sharePoint server and it
    is working fine with environment  Office web apps not configured with Sharepoint.
    Looking resoluion /suggestion, thanks in advance.
    Regards,
    Sushil

    Hi  Sushil,
    According to your description, my understanding is that the add new document link was not working on machine where Office web apps set up with this SharePoint server after you upgraded SharePoint team sites
    from 2010 to 2013.
    For your issue, it can be caused by integrating Office Web Apps with upgraded SharePoint Site.
    Firstly please make sure claims-based authentication is used by the SharePoint web application that is used to create the new document. Only web applications that use claims-based authentication can open
    files in Office Web Apps. To determine the authentication provider for a web application, follow these steps:
    1.In SharePoint 2013 Central Administration, click Manage web applications.
    2.Select the web application that you want to check, and click Authentication Providers on the ribbon.
    The authentication provider must be displayed as Claims Based Authentication for Office Web Apps to work correctly with the web application. To resolve this issue, you can delete the web application and recreate
    it using claims-based authentication, or you can change the authentication method of the web application.
    Secondly, make sure the WOPI zones match on the SharePoint 2013 and the Office Web Apps Server farm.
    To do this, run the following command on the SharePoint Server:
    Get-SPWopiZone
    The result will be one of the following:.
    internal-https
    internal-http
    external-https
    external-http
    Next, run the following command on the SharePoint Server.
    Get-SPWOPIBinding
    In the output, look for WopiZone: zone. If the results from Get-SPWopiZone don’t match the zone that is returned by Get-SPWOPIBinding, run the Set-SPWOPIZone -Zone cmdlet on the SharePoint Server to change
    the WOPI zone to match the result from Get-SPWOPIBinding.
    If not work, you can try to disconnect SharePoint 2013 from Office Web Apps Server and re-configure Office Web Apps for SharePoint 2013.
    For more information, please refer to the article:
    http://technet.microsoft.com/en-us/library/ff431687(v=office.15).aspx
    Best Regards,
    Eric
    Eric Tao
    TechNet Community Support

  • Error message on my HP Photosmart C7280 All-in-One 'Wireless Radio not Working'

    error message on my HP Photosmart C7280 All-in-One  'Wireless Radio not Working' My broadband is BT Infinity with a very strong signal throughout the house and my operating system is Windows XP. My printer will not connect wirelessly to my network, what can I do with respect to the error message 'Wireless Radio not Working'

    Hello @GeoffH777 ,
    Perfect! You are very welcome, I am very happy to hear the reset helped!
    If you  have a quick moment, please scroll back to my last message here and click the "Accepted Solution" button, so others can find our thread if they happen to run into the same issue.
    Greatly appreciated, have a wonderful day!
    R a i n b o w 7000I work on behalf of HP
    Click the “Kudos Thumbs Up" at the bottom of this post to say
    “Thanks” for helping!
    Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

  • Fresh Install HCM 9.1 but Links not working. Help please

    Dear All,
    I'm trying to make a switch from SAP to PeopleSoft. I tought it easier to install PSFT since the number of source to install is much less than SAP. However, I kept getting same error where the links not working no matter which environment I tried to install.
    I downloaded all software from eDelivery.
    HCM 9.1, PTOOLS 8.52, Oracle 11g 64 bit, Oracle Client 32 bit.
    First Try:
    Install on windows 7 64bit. Everything works fine until first login to the PSFT and all links not working.
    Suggestion from Hakan is to apply the patch and gave me a link to the old FTP site. I downloaded the 85209 patch but got password.
    Finally I managed to get a customer ID from a friend and downloaded Patch 85211 and applied. But got java error so I scrapped it.
    Anyway, Gasparotto said the environment is not certified and will not fix my problem with the patch.
    Second Try:
    Installed Virtual Box.
    Installed Windows 2008 R2 and applied the SP1.
    Installed everything all over again.
    Ensured the PTWEBSERVER password similar the username.
    Everything works fine but when login to PSFT, again..... links not working and see on the bottom left corner there are some javascript error where they cannot find certain peoplesoft objects..
    Just upgraded to IE 9 because I read somewhere IE 8 is not certified.
    Tried to login again, no error message and everything looks fine but... links not working.
    Logs also looks normal to me.
    Does anyone ever encountered similar issues before?
    Does this is a normal behaviour before tools patch 85211 being applied ?
    Thanks,
    aLuNa
    My APPSRV Log:
    PSSAMSRV.12 (0) [11/03/12 09:04:46](0) PeopleTools Release 8.52 (WinX86) starting. Tuxedo server is APPSRV(99)/100
    PSSAMSRV.12 (0) [11/03/12 09:04:46](0) Cache Directory being used: C:\APPSRV_CONFIG\appserv\HCDMO\CACHE\PSSAMSRV_100\
    PSSAMSRV.12 (0) [11/03/12 09:04:46](0) Server started
    PSRENSRV.2808 [11/03/12 09:04:49](0) PeopleTools Release 8.52 (WinX86) starting. Tuxedo server is RENGRP(92)/101
    PSRENSRV.2808 [11/03/12 09:04:49](3) Switching to new log file C:\APPSRV_CONFIG\appserv\HCDMO\LOGS\PSRENSRV_1103.LOG
    PSADMIN.2124 (0) [11/03/12 09:04:52](0) End boot attempt on domain HCDMO
    PSAPPSRV.1488 (3) [11/03/12 09:13:16 GetCertificate](3) Returning context. ID=PTWEBSERVER, Lang=ENG, UStreamId=091316_1488.3, Token=PSFT_HR/2012-11-03-02.13.17.193528/PTWEBSERVER/ENG/XxZ3vyJWXF/S1MoQtG2Wox6wGJA=
    PSAPPSRV.1488 (5) [11/03/12 09:13:21 GetCertificate](3) Returning context. ID=PTWEBSERVER, Lang=ENG, UStreamId=091321_1488.5, Token=PSFT_HR/2012-11-03-02.13.22.193632/PTWEBSERVER/ENG/pS6ec6pIAJJSYc1oOWcNYiR0UFQ=
    PSAPPSRV.1488 (7) [11/03/12 09:13:29 GetCertificate](3) Returning context. ID=PS, Lang=ENG, UStreamId=091329_1488.7, Token=PSFT_HR/2012-11-03-02.13.30.193285/PS/ENG/3GnOezS6D9PUlzwrjPwqexv4ir0=
    PSAPPSRV.1488 (34) [11/03/12 09:18:47 GetCertificate](3) Returning context. ID=PS, Lang=ENG, UStreamId=091847_1488.34, Token=PSFT_HR/2012-11-03-02.18.48.194158/PS/ENG//oJB5tvSHYNzsmZ2Gs4g2vBLUVs=

    alunwawa wrote:
    Does anyone ever encountered similar issues before? Yes, I did already see the same, that was when installed the same with 8.52.00 (without Peopletools patch) or without applying the patch project...
    Does this is a normal behaviour before tools patch 85211 being applied ?Without patch, you have the error you mentioned. How many time I told that 8.52.03 min. is required, I did not go further, but there was some bugs before which make it not working.
    I understand that's rather frustrating for people who wants to jump to Peoplesoft. I don't know SAP, but here you go, Peoplesoft is not a simple toy.
    Unfortunately, if you have no access to My Oracle Support to get the Peoplesoft patches, you have no way but work on Peoplesoft OVM (free of use), and to use them on VirtualBox, the Jim's articles are worth to follow.
    Nicolas.
    PS: @Jim, thanks for the kind words.
    My last install guide is quite old now (PT8.50/Linux), even though it did not change very much within the last tools 8.52. But seeing the number of time such questions have asked over here (PT8.52 on Windows), I'm thinking to write one more, that time on Windows.

  • Purchased Lightroom 5 and Download link not working. Please advise

    I have Purchased Lightroom 5 followed the download instructions and Download link not working.
    I get a dialog box stating that I have Explorer 4 and I need a later version.
    I am in fact running Explorer 10.
    Please advise.
    Bob Spree
    England

    Please see http://forums.adobe.com/thread/1229333 where this topic has been discussed.

  • HP 5524 Wireless does not work after firmware upgrade

    HI,
    I have just purchased an HP5524.  After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
    The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully. 
    However, ever since wireless will not work.  Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum.  The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
    Thank you

    Hi,
    Thank you for posting you query,
    In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen  instructions.
    If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup  and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • Links not working correctly in PCUI for CRM

    Hi All,
    We are implementing mySAP CRM 4.0 through PCUI on Portal
    EP6 SP14.
    I have integrated the CRM Business Package 60.2 in Portal.
    Proper User has been created in the backend and assigned Sales Manager Role both in the portal and in the CRM backend.
    We are facing problem of links not working in the CRM Contents. When we click on the links in the CRM Portal Contents ( BSPs) we don’t get the desired application opening.
    When we click any links in the BSP's ( Activity Links in Opportunity Management BSP ) we get a blank page popped up.
    I have the screen shots with me. Any one responding can get the screen shots from me.
    Thanks in Advance
    Rohit

    Rohit,
    Have you maintained configuration in (transaction CRMC_BLUEPRINT_C --> Navigation (URL Generation) --> Assign Object Method to Role)? Be sure that the role that you are using is present and ID Page/Service field correctly points to the pcd url for your portal.
    When testing, it may be helpful to set parameter CRM_URL_BUFFER_OFF = X on the user profile (SU01) to turn off the url buffer. That way changes made above are immediate.
    Best Regards,
    Bernard

  • Web links not working in iPhone calendar notes. Used to work. Ideas?

    Web links not working in iPhone calendar notes. Used to work. Ideas?

    Basic troubleshooting from the User's Guide is reset, restart, restore (first from backup then as new).  Has any of this been tried?

  • Why Does Dynamic Link Not Work

    I purchased the CS5 Adobe Production Premium.  I have been working in Premiere and I have been learning about how to use Dynamic Link. I want to be able to alter clips in After Effects and bring them back and forth into Premiere.  When I go to File/ Adobe Dynamic Link/New After Effect Composition, I get this message:
    Adobe Dynamic Link Requires Adobe Production Premium.
    Since I own production premium, I do not know why I am getting this message.  I have reinstalled the CS5 Production Premium Software twice and it still gives me the same message.  What can I do to get Dynamic Link Working.

    Thank you for the tip.  Could you possibly tell me how to deactivate and
    then reactivate the suite.  I am using a Macbook Pro laptop running OS
    10.6.4.  I do not even know where to start.
    From:   Colin Brougham <[email protected]>
    To:     Dan Seanor <[email protected]>
    Date:   03/15/2011 09:55 AM
    Subject:        Why Does Dynamic Link Not Work
    Deactivate the software (not uninstall), and then reactivate the suite.
    This often fixes this. You can opt to leave the serial number on the
    system; no need to clear it and re-enter it.

  • Verizon Access Manager Download link not working

    Hi,
              Verizon Access Manager Download link not working, Following Links
    http://www.vzam.net/download/download.aspx?productid=872
    http://pcdn2-download.vzw.com/win/7.7/VZAM_7.7.1_2727b-AC30-Web.exe
    plz help to download verizon five spot access manager.
    thanks
    karthirocks

        Hi karthirocks! I'm sorry to see you're having any difficulties using these links. I've clicked on both, but had no problems getting pages to launch or in getting the application to download. If this is still a problem for you, please describe the issue you're experiencing. Also, please share the browser version you're using, and if you've enabled any security feature that prevents access to certain secure sites or services. Thanks!
    DionM_VZW
    Follow us on Twitter www.twitter.com/vzwsupport

  • Tecra A3 - Creative Mouse Wireless does not work

    My Creative Mouse Wireless does not work while touchpad is installed.
    Even if I disable the Touchpad, the mouse seal does not work.
    Does anyone know how to solve this problem?
    Thank you,
    R.P.

    Hello
    On this way it is not easy to say what the problem is. I assume that you got some installations software for your external device. Install it and it should works.
    As far as I know functionality of external mouse doesn`t depend on touchpad settings.
    Bye

  • Flash Global Security & Links Not Working?

    Hi all,
    I am absolutely near some sort of breakdown with my Flash website....I really hope someone can help!
    I am building my portfolio website; I'm using Dreamweaver CS3 (on Mac) and inserting Flash animations in the centre of a table in each Dreamweaver page. All was working fine until I built the Contact page animation on Flash last night. I linked in some external websites to my Blog, Flickr and Twitter and also need a button to launch the user's default mail client.
    When I tested the animation (CMD+ENTR) in Flash the links appeared to be working, if after a few clicks. I then inserted the Contact animation into the Contact.html page on Dreamweaver and tested it in Safari. A dialogue box came up regarding something about security settings and Flash 8 (makes no sense as I am using Flash 9); and I ended up on the Global Security Setttings panel page on the Adobe website. I selected the entire folder the website is in on my hard drive under "Trust Files in these Locations". Now the ENTIRE website's flash animations are not working. There are links to internal pages of the site (i.e. a link to the "Contact" page in the animaiton on the Home page) which are now not working either. No error messages come up when I test the movie in CS3 either. I have refreshed Safari, restarted the Mac and redone the folder on the Global Security Settings panel. Also loaded the entire website onto a PC this morning, all links not working either.
    Actionscript 3 on the Contact page looks like this:
    import flash.events.MouseEvent;
    //---Blog Button---\\
    var getBlog: URLRequest = new URLRequest("http://www.myblogsdomain.com");
    Blg_Btn.addEventListener(MouseEvent.CLICK, eClick);
    function eClick(event:MouseEvent):void{
    navigateToURL(getBlog, "_self");
    //---Twitter Button---\\
    var getTwitter: URLRequest = new URLRequest("http://www.twitter.com/mydomain");
    Twt_Btn.addEventListener(MouseEvent.CLICK, eClick1);
    function eClick1(event:MouseEvent):void{
    navigateToURL(getTwitter, "_self");
    //---Flickr Button---\\
    var getFlickr: URLRequest = new URLRequest("http://www.flickr.com/photos/mydomain");
    Flkr_Btn.addEventListener(MouseEvent.CLICK, eClick2);
    function eClick2(event:MouseEvent):void{
    navigateToURL(getFlickr, "_self");
    //---Email Button---\\
    var getMail: URLRequest = new URLRequest("mailto:[email protected]");
    Eml_Btn.addEventListener(MouseEvent.CLICK, eClick3);
    function eClick3(event:MouseEvent):void{
    navigateToURL(getMail, "_self");
    I'm not 100% sure if the e-mail AS3 I set up is correct, but as none of the links are working I can't test it. I cannot provide a link to the website as it isn't uploaded yet, and I don't really want to upload it not working properly.
    Any help at all would be gratefully received, I'm really, really on the brink of some sort of breakdown. Thanks.

    Thanks Samuel.Wong and Ned Murphy for the information.
    I'm not actually sure what happened but my website suddenly started working again today, I think possibly by selecting "Always Allow" on the Global Security Page as well as inserting every individual file as well as the folder under "Trusted Locations" has also done the trick.
    The external links appear to work when I test the movie in Flash CS3, but the same warning comes up once the movie is inserted into a Dreamweaver html page and tested in Safari. However I think when the links (all except the email ) appear to be working in Flash then it should be just fine once uploaded onto the server. Many thanks for your advice once again.
    Maxx

  • My wireless keypad not working even in a full battery, window display continously switching automatically without touching the cursor.

    my wireless keypad not working even in full battery

    I have a wireless keyboard with the attached keypad.  The keyboard is working great, but the keypad quit working.  I put in new batteries...did not help.  Any suggestions?

Maybe you are looking for