WRT600N problems setting up a home net with PDAs

Good afternoon,
I've just bought a WRT600N and I'm having problems to configure.
Network configuration: 4 computer wire connected;1 laptop and 2 PDAs (Ipaq hx47000 & Ipaq hx2490b);
OS: Windows XP Proffesional and PDAs Windows Mobile 5.
Internet cable connection.
Security at 2.4Ghz. WPA-personal + TKIP and MAC filter enabled.
No activity expected at 5 Ghz.
Problems:
- I can't connect PDAs to Internet. Only able to connect but with some difficulties (sometimes loose connection) and always have NO Internet access.
- I can't see network places from laptop or PDAs.
- I can't access to web based utility from computers only from laptop.
Steps alrady done:
- IP reserved for each PDA' MAC address..
- QoS disabled.
- Beacon interval increased to 800.
Could anyone help me to fix it?. Thanks in advance.

I looked through the User Guide for both of your PDA's. There is no mention that they support WPA encryption. They User Guide says that they only support WEP encryption.
Unless HP (or Microsoft Windows Mobile) has released some new wireless drivers for your PDA's, it looks like they won't do WPA.
If you believe that you have the WPA drivers, then I would suggest that you first connect your PDAs using no encryption and no MAC address filtering. If this works, then turn on only the WPA encryption. If this works, try the MAC address filtering.
Message Edited by toomanydonuts on 04-21-2008 06:24 AM

Similar Messages

I am having problems connecting to my home wifi with my iphone4s

Over the past couple of weeks I have experienced a problem connecting to my home wifi service (Sky) with my iphone4s although my laptop connects fine. My phone also picks up the wifi at my place of work. At home when in close proximity to the router (netgear) on the phone the network name appears in the wifi settings but on the wifi networks page it does not get a tick against the name (wheel just keeps revolving). I have taken it back to the retailer (Vodaphone) and they recommend it be sent back to Apple (Liverpool or Manchester) as they consider it a hardware fault. I will be without the phone for probably 1-2 weeks and I use it within my working environment regularly.
Has any one any ideas?
jd
ps. If I go down the route of 'forget this Network' will I need to do any resets on the router as I cant find the username and password when I enter my IP address for the router.

are u there

Problems Setting up my wireless network with an Xb...

Hi, I have had some problems setting up my wireless networking.
I have everything switched on and am able to go online with the laptop and the Xbox with no problems but when I try to share media with the xbox I have problems.
I have opened the ports specified in the setup from xbox on windows firewall and have no problem connection Via Ethernet cable but when using wireless the xbox cannot detect the laptop.
I have checked the network map and both xbox and laptop are connected and have enabled sharing and am running sharing software.
Below is the network map.
I have also been having problems with BT software, the free virus protection will not install, The desktop help will not launch although it shows up on task manager and the installation disk does not launch correctly it doesn't get past the loading screen.
I have had a printer on the wireless network and had no problems printing.
If anyone knows how to resolve this please help.

I have this same Motorola modem and I just verified that my 802.11n AirPort Express Base Station (AXn) can get Internet access with this modem without any issues.
When changing ISPs (or networking equipment) it's always a good idea to start from "scratch" in configuring your equipment.
I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Power-up the modem; wait at least 10-15 minutes.
Power-up the base station; wait at least 5-10 minutes.
Power-up your computer(s).
In this basic configuration, computers connected to the base station, either by wire or wireless (as appropriate for the base station type), should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options.

Problems setting up a WRT54G router with Vista

My husband upgraded to Windows Vista Home Basic over the weekend (we don't have the newest version! omg!angst!woe!). Today, I got a call that our DSL was turned on, I set up the modem, got the internet working, and attempted to set up the wireless router.
I have used the setup cd, the EasyLink program, and the directions to manually set up the router. I can get the router linked up properly, I can even log into the DSL modem through the router. The problem is that I can't get any of these setup programs to recognize the router. Even putting in http://192.168.1.1 brings up a "page cannot be loaded" error in both Firefox 2.0 and IE (however, when I remove the router, I can see the DSL modem fine with it). Is there some other way to get the wireless router set up, or do I need to wait for one of the two computers with XP to arrive (yay for moving with the military) to set up the router?

Hi,
I too am having problems connecting the WRT54GS to my vista enabled pc. I have installed the software but since connecting everything my internet access is now diabolically slow. This is on the main wired machine, not wirelessly. The router is obvioulsy doing something inbetween (possibly the firewall) but this has made the speeds almost unbearable, negating the object of the new pc !!
Is there some settings I should eb checking ?
Many Thanks

Problems setting up testing server CS5 with existing PhP site copied to hard drive

A couple of years ago I dabbled in CS3 & PhP, but haven't touched it since 2009. I still have WAMP loaded on my machines. I'm now in a work situation where I was asked to see if I could make some simple copy updates to sites written in PhP. I copied the entire sites over to my hard drive, and placed them in the WAMP www root folder, and followed instructions to setting up the site in CS5 (which is pretty close to the CS3 setup). I made sure WAMP was running, and I'm still unable to connect. I am using "localhost" as part of the URL for the web server designation. I continue to get an "internal server error" message on these pages. I am able to, from my browser, type in "http:localhost" and it appears that WAMP is running properly. And I do remember to start WAMP before I start a DW session.
So, I kept experimenting. If I define a new PhP site and create a test document with simple PhP code, the connection to the testing server works and renders the code. It's just the existing PhP site I've copied over generates the Internal server message.
Is there something basic I'm not understanding about viewing and manipulating a PhP site created by someone else using DW CS5?

The first question: on what platform? Windows - Mac?
I only succeeded in setting up a testing server on my Mac
with PHP and MySQL after reading a book of David Powers. On Leopard
I belief there still are problems connecting PHP to MySQL.

Problem setting up ATT email account with Apple Mail

I have a main ([email protected]) and sub email account ([email protected]) with ATT/Yahoo (formerly SBC).
I set these accounts up on Apple Mail for the first time, and selected the option "Remove copy from server after retrieving a message "RIGHT AWAY". But Apple Mail would not allow me to select that option for both the primary and sub account. It allowed me to select that option for the first account I set up (the sub account), but when I tried to select that option for the second account (the main account), it would not permit me to save the option and gave me the following error message:
The account path /Users/edelbert/Library/Mail/[email protected]@pop.att.yahoo.com is already being used by the account "GIFilm"
It will allow me to select the option to remove the copy AFTER ONE WEEK, but then I receive the same message over and over each time Apple Mail checks the ATT server.
ATT claims that it is the result of an SSL conflict between its software and Apple's, and claims that Apple has created a bug fix, but I can find no evidence of such a patch.
Can anyone help me?
Thanks

As far as I can tell, the problem might be with my password. It's working on my iPhone, but not my computer.
If it's just a matter of changing the password, it's cool. But I can't figure out how to change the password.
Any ideas on changing the password in mail preferences?
Thanks,
mhh

In my home net with EA450 doesn't work Remote Desktop Access

Hello.
Today I've bought new LinkSys EA4500. And now it is a promlem with RDP into my home network (not from outside). My iMac can't to connect to PC by RDP and so also iPad can't. The PC is working properly and at this moment I can see it by web access from iMac at this moment.
Last three years I used a LinkSys WRT340 and it worked without problem in my network. Wherw may be a problem with setups EA4500 and what is solution?
Thanks.

I believe this concern is regarding the new design of the router of not supporting reverse NAT. To know more about this concern, click on the link below.
Protecting Your Router Against Possible DNS Rebinding Attacks

Help setting up small home network with PC and an imac!!!?

I have an imac in my room, and my mother has a JP PC in her room across the house. We have a router and modem on her computer(I connect to the internet through the router signal)
I just recently bought a new printer. It is a wifi printer. I was told by a friend that I need to setup a small netowrk so all the computers/printers in the house can talk to one another. Because right now my printer is installed and connected to the router signal (but my computer does not reconize it to print....)
I started a small network on my moms PC...but when I can't make a network CD like it tells me to because my computer is a Mac....how do I continue to setup this network?Can I set it up first on my mac as well???PLEASE HELP! I want to use my printer!

You can just connect the WRT54G wireless router’s LAN port to BEFSR41 router’s LAN port by using a network cable as specified in this configuring wireless router as access point article, after that can connect other computers to that wireless router with or without cable. Finally do more test to check the performance. Hope it helps.

Setting up bt home hub with airport extreme and timecapsule

Hi I am running BT Broadband direct into a BT Home Hub (Black version) then ethernet into an airport extreme.
Timecapsule then extending the apple network and an iMac ethernet into the timecapsule
Various other macbooks, iPhones,iPads, iPods and apple tv wirelessly linked in. (and an hp multifunction printer)
The network seems very slow and unstable - any suggestions on how to tune it?
Thanks
Nigel

Introducing wireless repeater or bridge causes double hopping wireless. It greatly reduces speed and efficiency of wireless. I am not 100% sure I understand your arrangement. But there are limited wireless channels and the result of many wireless devices fighting each other is bad.
1. Do you have wireless turned off in the Home Hub? Please do unless it is providing important connections.
2. What mode is the AEBS running in? Because with BT you must use the home hub as a router, you should have the AEBS bridged. Is that the case?
3. Wireless extending networking adds issues as stated. Get rid of this. The best method is to link the TC and AEBS by alternative.. ie ethernet is the best by huge margin. If you cannot do this in your house then use EOP adapters. They are not foolproof but if they work, they keep working with reliability and stabilty and speed that wireless cannot match. You can then run the AEBS and TC as roaming WAP, by using different channels but same SSID (wireless name), and security settings and passwords.

Problems setting up multiple exchange accounts with same user name

Hello,
I have two email addresses on the same exchange server at work that I would like to configure on my iPhone4 running iOS 4.3.3. I can setup the first email just fine but when I set up the second email iOS tells me " Cannot Create Account: An identical Exchange account already exists". Here is a working example:
[email protected]
[email protected]
username and password for both email1 and email2 are the same credentials. Am I getting this error message b/c the username for both accounts is the same? if so is there a workaround for it without having to change the username for one of the accounts?
Any help would be appreciated. Also, we are using Microsoft Exchange 2010.
Thanks

I'm having the same problem. From all the information I can find, iOS doesn't allow you to access multiple Exchange accounts using the same credentials. I'm not sure if this is a restriction of iOS or a restriction of Exchange ActiveSync.

Problem setting comp to 133 fsb with MS-6390 \ bios flash problem

Ok you see when i under clock the computer to 100 fsb with a AMD 2400+ it will start by self and all is fine, but when i set it to 133 fsb(original speed) it need to restart cmos so that it will start again, also keeps poping up set date when i start windows so that might be battery but in just makeing sure. Also when i flash my bios after i says backup and i type y then it backs it up it will say directory not found or something, anyone got a solution, see if i dont need or need to flash bios and how to get it working?

naw dun got one (but got enough for it 30k =) getting it when i turn 16 =P ( curently 15 almost 16 in like 4 months but anyways back to the topic it is a top of the line power supply
MS-6390 KM266 Motherbaord
Radeon 9200 SE
Kbytes DDR PC 2700 333MHZ 256 MB ram stick
450 W Power Supply
Sound Blaster PCI Sound Card
AMD 2400+ Socket A
Maxtors 120 GB HD @ 7200 RPM
Model : Okia 420 ATX ( 420w Max)
Vac~Input |Voltage 115/230v| Voltage 10a/5a) | Frequency 60/50 hz
Max DC | +3.3 | +5 | +12| -12 | -5 | +5sb |Green | Grey |
OutPut | 28A | 40A| 18A|1.0A|3.0A| Com |P-On | PG

New Asa 5505... Anyway to set up behind home router with no internal DNS?

Since the home router is the DNS server, the Asa has no internal DNS which is probably the cause of no internet. Is there any way around this?

Can you not simply use the ASA as the DHCP server and include the DNS server in your DHCP configuration ?
Jon

How do you properly set up a home network with multiple devices? I have a macbook pro, an iMac, and several other phones, tablets, roku devices, etc. Everything works properly except for when I try to access the other computer through the network.

I have an iMac and a macbook pro that I used to be able to share files between but ever since I moved 3 months ago I can't get it to work. Also, now my phone and my wife's phone are inseparably connected. She seems to be getting all of my text messages but I don't get hers. We also bought new computers right before we moved so that might have something to do with it. Both computers are on my account and have my name. Thanks in advance, it would be nice to get this working again - tired of walking ten feet with a flash drive to share files : )

The following may help with the file sharing issues: OS X Mavericks: Share your files

Problems setting volume of a net stream

I'm using this actionscript, but the volume doesnt seem to be
set to 0.
Any tips, greatly appreciated.

Yes I know setVolume, but I was looking for a solution
without actionscripting.
The sound is not controlled through actionscript but is
integrated in author
environment, so I thought perhaps there is any hidden feature
(in the prioperty
panel?) to configure allowing you to set the volume.
For example if you drag and drop a sound from the library to
the stage, I
would expect a feature in the property panel to setup the
volume but obviously
there is none.

Trouble setting up a home network

Hi,
I have the Actiontec M1424-WR router. I am trying to set up a home network with a Desktop on XP and a Laptop on Vista.
I have been able to creat a network if the Desktop and Laptop are both connected to the Router with Cat5 Cables.
I can not set up a network if I have the Desktop connected via the Cat5 and the Laptop using the Wireless Card.
I've called VZ, won't help. I've emailed Actiontec, couldn't help. I've Googled etc. I'm stumped! This can't be a unique situation.
If anyone can help it would be much appreciated.
Thanks!

Log on to the computer.
Click the Start button ‌, and then click Connect To.
Choose the wireless network from the list that appears, and then click Connect.
Type the security key (which is the WEP key stamped on the Routers tag) and then click OK.
You will see a confirmation message when you are connected to the network.
To confirm that you added the computer, do the following:
Open Network by clicking the Start button and then clicking Network.
You should see the icons for the computer you added and for the other computers and devices that are part of the network.
Side note:It’s important to use the same workgroup name for all of the computers on your network. This makes it possible for computers running different versions of Windows to detect and access each other. Remember that the default workgroup name is not the same in all versions of Windows.
Joe D
Verizon Telecom
Fiber Solution Center
Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.Follow us on Twitter™!

WRT600N problems setting up a home net with PDAs

Similar Messages

Maybe you are looking for