WRT610 wireless connection quit working

I just bought and installed a WRT610N for my wireless network. I have 5 laptops and a desktop running various OS, such as WXP, Vista Home, Vista Ult., etc. Also have a range expander. Everything was working last night. All with the same SSID's, all using the wireless WPA. Range expander was working Blue, Blue. Router was setup in default mode (Wi-Fi protected). This morning, the range expander was Red, Blue, and none of my wireless connections worked. I finally uninstalled the 610 setup software, reset, bebooted, you name it, and I still cannot get any wireless connection. I have wired connection, obviously, as I am writing this. I've about had it. Any thoughts here? Something I may be missing?

I am afriad, WRT610N is not compatible with WRE54G Range Expander...I wonder how both worked together...

Similar Messages

My ipad 1 for no apparent reason no longnet. Our home wireless connection is working for all other devices. Any clues?

My Ipad 1, for no apparent reason, no longer connects to the Internet. Our home wireless connection is working for all other devices.Any clues?

You can also try to reset your network settings on the iPad. Go to Setings>General>Reset>Reset Network Settings.
Good Luck!

Safari is not connecting to internet on my iPad. Says "could not open the page becuase the server stopped responding." Everything else that updates over wireless connection is working fine. Get same response on any site I try to visit. Need Help!

Safari is not connecting to internet on my iPad. Says "could not open the page becuase the server stopped responding." Everything else that updates over wireless connection is working fine. Get same response on any site I try to visit. Need Help!

I am having identical problem on my iPhone 4 running iOS6. Did NOT experience this issue prior to upgrade.

Time Capsule--Wireless suddenly quit working

My Time Capsule had always worked perfectly, but suddenly my wireless access from any device has quit working. My DSL is working fine, and the router and backup portions of the TC seem to be working. I tried a hard reset, updating to the latest version of Airport Utility and Firmware, and it still doesn't work. My laptop sees the network, but when I type in the password and try to connect, I get a connection time out.
Is there anything else to try, or do I assume it's broken?

Do a factory reset.. if the TC still will not pass IP addresses it is indeed faulty.. I get the idea it has swapped modes for some unknown reason. Anyway give it a try.. no luck and Apple will replace it.

Wireless connection not working after installed newest Lenovo ThinkVantage System Update programs

Hi, everyone!
I've installed some newest programs through Lenovo ThinkVantage System Update and just after that my wireless connection has stopped working. Here are the installed programs:
ThinkPad UltraNav Driver for Windows 32-bit version 15.0.24.0;
ThinkPad Power Management Driver version 1.60;
ThinkPad Modem Adapter version 7.80.8.0;
ThinkPad Hotkey Features Integration Package Setup version 3.11.0001;
Inter Wireless WiFi Link for Window XP version 13.02.0000;
ThinkVantage Access Connections for Windows XP version 5.62;
ThinkPad Power Manager version 1.88;
Lenovo ThinkVantage Toolbox (32-bit) version 6.0.5514.61.
I've got a Lenovo T61 with Windows XP SP3.
Also in Device Manager, there are now the two "Other devices" bellow with a yellow question point and a yellow exclamation point by side:
Bluetooth Hands-free Audio;
Bluetooth LAN Access Server Driver.
Does anyone have any idea what can be done to have these issues solved?
P.S.: when I click Fn+F5 it shows only the Bluetooth Radio.

Hello and welcome,
I've seen something like this on XP machines after updates a couple of times now - my T61, a friend's T400, and his daughter's T61. I guess that makes 3
_Maybe_ your situation is the same.
The fix in all 3 cases was to go to device manager and uninstall the wifi driver. Then scan for hardware changes and let it reinstall the driver. Something about how Access Connections or some other networking mangement thingy was hooking the drivers I guess.
On both of the friend's machines, the wired networking was also b0rked. Same fix there.
Z.
The large print: please read the Community Participation Rules before posting. Include as much information as possible: model, machine type, operating system, and a descriptive subject line. Do not include personal information: serial number, telephone number, email address, etc. The fine print: I do not work for, nor do I speak for Lenovo. Unsolicited private messages will be ignored. ... GeezBlog
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

Printer keeps dropping wireless connection after working for a while

My computer stops being able to communicate with the printer wirelessly even thought the printer says it is connected to the network and both the printer and computer are on the same network. What happens is I connect the printer to the network and print something from my computer. Then, after a short while, half an hour maybe, when the printer shows it is connected to the network, I try to print but my computer can't find the printer. The message say the printer cannot be found. If I go to the printer, and reconnect with the wireless connection wizard I can print. But after a short time, I won't be able to print again and have to do the wireless connection wizard again. Wireless direct is off. Don't know if that matters.

These settings are for setting up your wireless printer to stay connected to your router, keep wireless devices better connected and makes your router secure and hack proof.
Set a static IP in the printer (click here) outside the DHCP range of the router (check your manual). This is for Linksys routers but can be used for all routers. Verify your DHCP range and change this first if needed. More Wireless Printing help is here (Windows solution 4, static IP).
Verify in the printer that 'Auto Off/Sleep' is disabled. Use the Embedded Web Server (EWS) by going to the printers IP address in your browsers address bar, click Settings Tab/Auto Off. Or use the Printer Assistant, Printer Home Page (EWS). Also check your Printers Properties.
If the printer supports and has IPv6 enabled, turn off IPv6 in the printer.
If needed and you assigned a static IP address, try using 8.8.8.8 for the Preferred DNS server and 8.8.4.4 at the Alternate DNS server.
In the router: (Refer to your router manual for information)
Use a fixed wireless channel like 1, 6 or 11, never 'auto', try channel 1 first then the rest.
Set router to 20Mhz only, or 145Mbps depending on router.
Always use WPA2-AES (Personal) encryption, but you can try ‘mixed’ mode.
Disable WPS and never use it and disable UPnP for the routers security. Nobody can hack your system now and helps with wireless connectivity (if you want to know why, search the web).
If you have a dual band router (2.4Ghz and 5.0Ghz bands), make sure the SSID’s are NOT the same, they must be different for all bands, even for any Guest networks.
SSID broadcast must be enabled.
Save all settings. Power off both, wait 2 mins. Power on router wait 2 mins.
Power on printer and verify it reconnects to router.
Windows 7/8/8.1 Is Network Discovery on or off?
Control Panel/Network and Internet/Network and Sharing Center/Advanced sharing settings.
Under Home or Work (current profile) / Network Discovery.
Select "Turn on network discovery" and save changes.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Two years trying to get Toshiba Laptop Wireless Connection to work

I've been trying for the last two years to try and get the wireless connection on my Toshiba Laptop to work without much sucess. I did for a short time manage to establish an ad-hoc wireless connection from the Laptop to a Desktop and share the internet connection that way but then that stopped working.
I have a Toshiba Satellite Pro U400-15L model no PSU45E-00J005EN. It's the one with the 12.1" screen and running Windows XP Pro sp3.
My Wireless switch on the front of the laptop is turned on. It is also enabled in the software FN F5 Wireless enabled, bluetooth disabled. I don't have Intel ProSet.
Previously when I managed to establish an ad-hoc connection that was using microsofts software. I had to manually enable the Wireless Zero Configuation (WZC) each time though as it always started disabled or stopped even if I set it to start automatically. It was a monumental PITA.
When I try and connect to the home ADSL Wireless Router (Belkin N150) using the Toshiba software I get the error message "another vendor's application is controlling the wireless adaptor".
I get this all the time even if I have disabled Microsofts Wireless Zero Configuration (WZC).
I was thinking Windows was still somehow controlling this even though I have disabled WZC so having read solutions in other posts I have tried going to...
contol panel -> network connections -> wireless connection -> properties -> wireless networks tab -> uncheck "Use Windows to configure...".
But unfortunately there is no "wireless networks tab" in there, all I have is the other two tabs. And since trying to use Toshibas software to establish the wireless connection using their Radar thing, now when I click into the wireless network connection it has the message "Windows cannot configure this wireless connection. If you have enabled another program to configure this wireless connection, use that software."
Can anyone on the forum or at Toshiba help please?
Thanks,
John

Two years? Sorry but I cannot believe it.
If everything is Ok and I mean if there is no hardware problem you dont need longer than two minutes for WLAN configuration.
At first you must be sure the WLAN card is installed properly (device manager).
WLAN card must also be enabled properly (switch > check FN+F8 > check ConfigFree tool).
When he WLAN card is enabled properly (check status in ConfigFree) scan the area using option RADAR in ConfigFree.
Can you find this option?
Can you scan the area?
Is some WLAN visible for your notebook?

Tiger...smtp connection quit working, port 25. Now iPad mail quit. Help

10 4 11 smtp port 25 quit working, cannot connect. iPad mail also quit working.

iPad...no msgs, just forever connecting....Verizon carrier.
Macs....just says smtp connection failed.
Just tried the web mail....no load, says secure connection failed. However I can get into other emails, non apple, with no problem.

The airport utility software running on Windows7 is not able to find my airport extreme. Bute the wireless connection is working.

I have a stable wireless connection between my Laptop with Windows 7 and the airport extreme. But the airport utility software cannot find the air port extreme. The problem now is that I cannot install my printer which is connected via USB to the airport extreme. Can somebody help? thx

Try this Web page. These steps helped me. Hopefully this link works for you.
http://books.google.com/books?id=-yhGNt6fqkIC&pg=PT301&lpg=PT301&dq=%22For+Print er+Name+or+IP+Address+you+have+two+choices,+depending+on+whether+the+Windows+mac hine+is+connected+via+Wi-Fi+or+Ethernet+%22&source=bl&ots=q7h6Uvih-B&sig=XJOXFo9 yZmhRW6PPDafOKc4QywQ&hl=en&ei=C3DKTqOqE4S3twf7wJjNCw&sa=X&oi=book_result&ct=resu lt&resnum=1&ved=0CBwQ6AEwAA#v=onepage&q=%22For%20Printer%20Name%20or%20IP%20Addr ess%20you%20have%20two%20choices%2C%20depending%20on%20whether%20the%20Windows%2 0machine%20is%20connected%20via%20Wi-Fi%20or%20Ethernet%20%22&f=false

Wireless (ndiswrapper) quit working, no errors

I recently put Arch Linux on my laptop, installed the cvs version of ndiswrapper and setup my Broadcom (ick) wireless (using the stock kernel 2.6 ide). Everything worked fine so I updated my packages with pacman and made a custom kernel (2.6.11). I then recompiled ndiswrapper after reboot and everything went fine as far as reconfiguration goes. When I loaded the module my wireless light came on briefly and then turned off, however dmesg and iwconfig showed everything to be operational without any errors noted. When I tried to set the essid with iwconfig the output showed it was ignored (keeyping it set to off/any). iwlist wlan0 scan shows no results.
I tried reverting back to the stock kernel and recompiling ndiswrapper but still got the same results. I assume this is a package I upgraded that may be causing this? I tried re-installing wireless_tools and nothing changed (the latest is what comes with Arch .07 anyway).
Any ideas? I'm stumped, thanks for any help.

sudman1 wrote:Have you tried Phrakture's ndiswrapper packages? I've only heard positive things about them. The cvs version may be unstable.
Yes.. ndiswrapper and the rt2750 driver from http://rt2x00.serialmonkey.com/ quit working. The later crashing the kernel.
I've tried on both the stock arch kernel, and a custom 2.6.12.3.
Again, the wireless drivers were working correctly *before* .. and after a pacman -Syu and restart, they stopped (leading me to believe some package altered something critical). I've also tested against 4K and 8K kernel stack sizes.
Brice

How to set up WRT54GS so the wired and wireless connections both work?

I have a DSL line in to a Motorola modem.
The modem is connected to the WRT54GS with an ethernet cable.
When I connect my computers directly into the WRT54GS with an ethernet cable (there are four connection spots at the back of the box), I cannot go to the internet. I have 3 computers plugged in, but none of them connect via Ethernet..
Is there a setting on the router so that I can use the router for both wired and wireless connectivity?
Added info: I tried to connect directly from the computer to the modem, but again, got no connectivity. When I "chatted" with ATT, they told me the modem is set to "bridge", and that I could connect only one device. I don't want to change this setting because I want to use the router for the wireless capability. Besides which, I have more than one computer to connect to the internet.
How come I cannot just plug in and go?
My firmware version is v2.07.1.
I don't know how to find out what hardware version I have.
Other info is "DirectEthernet Connection, Speed: 100.0 Mbps, Signal Strength: Excellent, Status: Connected"
Also "1394 Connection 3, Speed: 400.0 Mbps, Status: Connected"
I don't know what that's for, but thought it might prove useful to those of you who are knowledgeable about such things.
Wireless is ok, but if I'm sitting right next to the router, I'd like to connect with Ethernet and take advantage of the better speed, etc.
Thanks in advance.

Just click this link.

Equium M40x - Wireless Connection not working

I have recently changed ISP from Orange to Virgin [cable] I was using the Orange provided Livebox with my Laptop and there were no connection issues. Virgin have supplied me with a Netgear WGR614 wireless router.
Now my Equim will not connect to it. Can anyone offer a newbie some help or advice? Is there a driver update needed or will i need to purchase a new wireless card for my laptop? Currently my wireless network connection is via an Atheros AR5005GS.

Do you see the wlan of your router and can you connect to it? Remember, you have to enter encryption key again for your new router.
If not, I think the trick with Netgear router is, to enable wlan functionality.
To do so, you have to connect router with normal lan cable. Then enter IP adress of router in internet browser, you can find this information in manual with username and password too.
Try this, as I don't know what exactly is your problem with your wireless connection.

Cannot get the wireless connection to work on mx459

I have tried for hours to set up the wireless connection. I even did the usb connect method. I enter the ip manually and it won't detect it....just keeps me looping to the detect ip automatically or use the network connections it detects. I tried the wps button on the router, printer doesn't find it. I can detect my network thru the lan settings on the printer, but my other computer just doesn't pick it up. Have tried everything suggested and that i could come up with, but im out of ideas at this point....any suggestions?

Sorry, i am trying to connect to it from an acer desktop running windows 8. athlon II x2 215 dual core processor. the router is a westell wireless router.

Wireless connection wont work

Wireless network will not connect no matter what it keeps saying INVALID PASSWORD!! Two Support technicians couldn't get my wireless connected to my Network!!

Wireless Diagnostics - About
Troubleshooting Wi-Fi connection issues - MacBook Air (Mid 2013)
Troubleshooting Wi-Fi issues in OS X
Wireless Connection Problems - Fix
Wireless Connection Problems - Fix (2)
Wireless Connection Problems - Fix (3)
Wireless Connection Problems - Fix (4)
Also try turning off Bluetooth

USB Wireless connections not working in Latitude E6320 , Windows 7

Dear all,
I having an issue with an external USB wireless network drive.
I can install with no issue, however it appears always disabled on the network connection.
Someone had a similar problem?
thanks
José Luz

Dear Hemalatha,
Thanks for your support on this issue
I tried to updated all network drivers but with no success.
Indeed disabled all the networks, I took several print screen
Please take a look below:
- All the network drivers are enabled execpet the TP-Link
- All the network drives are disabled
When I tried to enable TP-Link, i get this message
If we take a look at Computer manager, you can see that everything is disabled except TP-Link
However I´m unable to work wit it.
Thanks once again for your support.
Thanks
José Luz

WRT610 wireless connection quit working

Similar Messages

Maybe you are looking for