WRT610N 5ghz xbox 360 wireless N adapter won't connect (xbox 360 "Wireless Mode = Not connected")

Hi folks,
Looks like some other folks have reported similar. Haven't seen if an answer has been found anywhere.
WRT610v2 running latest firmware.
xbox 360 sees both the 2.4 network (ssid = network1) and the 5.0 network (ssid network2) when it does its scan.
Initially, xbox showed network strength for 2.4 network at 3 out of 4 bars and 5.0 network at 1 out of 4 bars.
Connects to 2.4 network just fine
Won't pull an ip address and reports "Not connected" when I select the 5.0 network.
I tweaked the wireless settings per some suggestions I found in this forum and now it shows the 5.0 network at 4 out of 4 bars signal strength. Also turned security on and off and xbox 360 reported the changes in security on the 5.0 network.
So the xbox 360 is definitely seening the 5.0 network. and can tell if it is running WPA2 or not.
If it can see the 5.0 network and recognizes what security and network type (infrastructure) is set, would would stop it from connecting to the WRT610n router and getting an IP address? No mac filters or firewalls are set and, again, connects just fine and gets an ip address if I select the 2.4 (network1 ssid) instead.
Won't work if I manually set IP, subnet, gateway, dns either.
Have tried mixed versus dedicated on the N radio...
Any suggestions would be appreciated.
thanks!
rjb

Hello,
Thanks for the suggestions. Tried as you suggested but still no luck. Seems to see the 5ghz ssid just fine with plenty of strength but just will not pull an ip address or even connect if I manually assign.
Any other thoughts?
thanks again for taking the time to respond.
rjb

Similar Messages

G5 Gigabyte Built-in Network Adapter won't connect at 1000

Built-in ethernet adapter will not connect to DLink Gigabyte switch even with a known-good cable. My other G5 connects fine to the switch in the same port. Adapter connects fine to 100mb Linksys switch. Really looks like a driver problem. Is there an updated driver for the built-in adapter? Or is there another solution?
Thanks
PowerMac 7.2 G5 Dual 2Ghz Mac OS X (10.4.9)

adkcomputerguy-
Greetings and welcome to the Apple boards.
It won't connect at all or just at 1000T? Could be a driver but I would suspect the cable. Are you connecting directly to the switch?
Have you ever been able to use this machine at gig speed? What happens if you connect the two G5's directly and make them their own network without a switch?
Luck-
-DaddyPaycheck

USB camera adapter won't connect to iPad

When I try to connect my KODAK camera to my iPad using the lightning to USB cable, it says that my camera requires too much power so I can't load my pictures. Is there anything I can do to get it to work?

Hi annie,
You need the Camera Connection Kit to download photos directly from your Camera to your iPad:
http://store.apple.com/us/product/MC531ZM/A/apple-ipad-camera-connection-kit?fno de=3a
Cheers,
GB

Broadcom 802.11ac Windows 8.1 won't connect to wifi router

I'm using a asrock z87E-ITX with Broadcom 802.11ac wireless adapter, and windows 8.1
my wireless adapter won't connected to my zte f660 wireless router, but it's connected to any mobile phone thetered device. The problem is when i try to connect, the wireless adapter is automatically disabled and enable it self after it.
i've tried using an external wireless adapter (TP link) and it's connected normally.

Hello padidisawah,
What is your current situation?
Have you tried the solution as MVP S.Sengupta mentioned?
Please take the following steps for troubleshooting:
1. Go to Control Panel\All Control Panel Items\Troubleshooting\All Categories and run the Network Adapter Troubleshooter
2. If the wireless adapter can normally connect to other Wireless router, please check the configuration in zte f660 wireless router.
Best regards,
Fangzhou CHEN
Fangzhou CHEN
TechNet Community Support

WRT54GS-Wireless devices either won't connect or disconnect when a game is launched

My old router went out last night, and I had a wrt54gs that was given to me a while back, so I hooked it up, but I am having some issues with it.
For a while it would say that it had no internet access, when it was connected. Then I couldn't get my wireless devices to connect (xbox, and cell phone) All I had done was change the name and the encryption to WEP.
I was able to get them online when I switched to WPA2 for a while. Then I decided to play a game (Tried Diablo 3 and Path of Exile) Every time I loaded up the game, the devices would get kicked off. WHen I disconnected from the game, they would reconnect to the network. Until 1 time they didn't. Now my Xbox wont connect at all, and my phone keeps saying the network is not in range, when placed a foot from the router. I've tried disabling UPnP, but that doesn't do anything. I've turned MAC filtering, on and off. I've powercycled, and just get no good results.
I'm not sure if this is just a bad router, or whats, going on. (FYI my old router was a 10 yr old D-link that I never had problems with)
Here is my ipconfig..any ideas? Firmware version is 7.2.08
Windows IP Configuration
Host Name . . . . . . . . . . . . : Dream
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8168C(P)/8111C(P) Family PCI-E
Gigabit Ethernet NIC (NDIS 6.20)
Physical Address. . . . . . . . . : 00-1F-D0-D2-72-C6
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::e859:6ea9:a69c:23b7%10(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Sunday, August 12, 2012 6:54:20 PM
Lease Expires . . . . . . . . . . : Monday, August 13, 2012 10:14:05 PM
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DHCPv6 IAID . . . . . . . . . . . : 234889168
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-06-8F-85-00-1F-D0-D2-72-C6
DNS Servers . . . . . . . . . . . : 24.217.0.5
24.217.201.67
24.247.15.53
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.{F3C3BCCF-D72F-401D-8DA5-01ACBE50DF61}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 9:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:825:2a05:b47b:eaeb(Prefe
rred)
Link-local IPv6 Address . . . . . : fe80::825:2a05:b47b:eaeb%12(Preferred)
Default Gateway . . . . . . . . . : ::
NetBIOS over Tcpip. . . . . . . . : Disabled

What are the details on the camera (Make, model, etc) ?
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.
If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

WRT610N Mac & PC - 2mbps wireless LAN file transfer rates

Equipment:
Linksys WRT610N connected to Motorola SB5101 Cable Modem
MacPro Dual Quad Core 3.0GHz XEON with three Western Digital drives set up on RAID 0 using internal Airport 802.11N.
Dell Inspiron 2600 - piece of crap but still get it done with Linksys WPC600N wireless card.
Sony PS3 connected to WRT610N via ethernet cable
DirecTV HR20-100 DVR connected to WRT610N via ethernet cable
Problem is this:
Internet speeds are incredible. LAN speeds are awful.
I was transferring a 914MB folder from the Dell Laptop to my MacPro.
The transfer took 14 minutes. That averages a paltry 2 megabits per second.
The wireless card on the laptop shows around 130mbps with excellent connection strength. My MacPro also is excellent connection. I guess the laptop has a 5400rpm drive. I've been able to stream video to my PS3 from the laptop using my OLD wcg200.
Is there something I can do to speed up the LAN connection? I haven't tried to stream to my PS3 yet. The WCG200 that I had wasn't all that good so I replaced it with the WRT610N. I'm starting to regret my decision.
thank you in advance
WRT610N | WPC600N | Dell Inspiron 2600 -> Win XP | Mac Pro -> OS X 10.4.11, 10.5.4 & Win XP via Parallels

More testing... I built a crossover ethernet cable to directly connect the Dell to my MacPro. The LAN speed was 100mbit due to limitation of the Dell network adapter. Speeds were between 46 and 82mbps. MTU was 1500 MTU at 1300 and 1200 yielded no additional benefit. I disconnected the ethernet cables and went through the WRT610N using my Airport Wireless N and the WPC600N on the Dell. Speeds max'd out at 1 to 2mbps. I must say the Linksys WRT610N isn't playing fair...or am I missing something else in the mix?
WRT610N | WPC600N | Dell Inspiron 2600 -> Win XP | Mac Pro -> OS X 10.4.11, 10.5.4 & Win XP via Parallels

My ATV gen 2 won't connect to the internet over a wireless BT home hub 5 network

My ATV gen 2 won't connect to the internet over a wireless BT home hub 5 network. I've recently upgraded to a BT HH5 and now I cannot airplay with my 2011-MBP, and the ATV will not connect to the iTunes store or software update.

Ok, thanks (not sure I know what you mean!). I have seen a solution that tells me to rename the two SSID's? Is that what you mean? All my devices are wireless, and all can connect to the internet except the Apple TV. Now I have disabled the 5GHz channel all devices are on the 2.4GHz channel and all work fine, including the Apple TV and airplay between my MBP and ATV.

Wireless NIC won't connect at N - stuck at 54mbps

I have an Acer Aspire, V3-771
The wireless card is an Atheros AR5BWB22
My router is broadcasting at 300MBPS (802.11 N) yet my connection is stuck at 54 MBPS. I have had problems with this NIC since the first time I started this laptop, it frequently won't connect to trusted networks and then after 5-10 minutes it will eventually connect. But now I am stuck and before I go out and buy an adapter that supports N or just change the internal network card I was wondering if anyone knows how I can possibly fix this?
If I go to network and sharing center then click on status of my connection it says connected at 54mbps. If I go to "Network settings">"Advanced options" it says under properties: SSID: myssid, Protocol: 802.11n
So if I am connected at N, why is the connection still only 54mbps? Any fix for this? I did go in to my router and make sure that it's broadcasting at 300mbps yet I am not getting anywhere near that... even 150mbps would be better. What gives? Is it the card? Thanks in advance!
Running Windows 10 home.

Maybe this makes no sense to you but try to disable IPv6, both on yout NIC and on your router. Reboot both devices and report here what happend.

Airport Express won't connect using 5GHz

Hi Everyone,
I've got an Airport Express set up in "join a network" mode out in my living room for Airtunes and to provide network to my blueray player that doesn't have wireless. I've got a dual band DLink dir-825 router in my den.
My problem is that the AE won't connect using the 5GHz spectrum. It does connect just fine in the 2.4GHz at N speeds, but it refuses to move up to the 5GHz spectrum.
I also have a mac mini that does connect just fine using 5GHz and N.
Is there any way to force the AE to join my network using 5GHz N instead of 2.4GHz N?
Thanks in advance for any help you can provide.

adsfushi, I just set up a dual network with my roommate tonight... we have two separate networks - one 5ghz (he can connect to it) and a 2.4 ghz that I can connect to, but I can't access the 5 ghz. It simply won't recognize me. Why would that be? I have an airport express and use a 24 inch imac. He has a mac book pro.

My HP OfficeJet Pro 8600 won't connect to my wireless router

This is bizarre. I have had my HP OfficeJet Pro 8600 for about 6 months. It has generally worked fine, and we have used it wirelessly only. But now it refuses to connect to the router. It can FIND the router, and it can find other networks in the area, but it won't connect to the router. I ran the Wireless Network Test, and the results say:
Wireless On - Pass // Wireless Working - Pass //
Network Name (SSID) found - Pass // Wireless Networks Detected - 9
Printer Settings Consistent with Wireless Router Settings - Pass / No Filtering - FAIL //
So it recommends solution as follows: "1 If MAC Address filtering is enabled, and you would like to keep it enabled, you must add the Mac address of your printer to the list of permitted devices for your router before continuing."
Except, guess what, I don't have MAC Address filtering enabled. I wouldn't know how to do that, much less check for it.
Also, before today, this was never a problem. HELP!
Thanks....
If you are interested, here's more detail and background.
Before today, the only problem we have had is that frequently our Apple laptop (OS X 10.6) has trouble connecting to the printer. This has been odd because the printer is connected to the network, and so is the laptop, but the laptop can't find the printer - it thinks the printer is "offline" (even though it's not). Usually, if I wait a while, it will find the printer, and it will resolve itself work fine. If not, we sometimes have found that it can fix itself if you restart the laptop -- restarting the printer does not make a difference. In fact, I did exactly that today, and it resolved itself. And I printed. Fine, right?
But then I wanted to do more printing, and the problem of the laptop not finding the printer came up again, so I decided to really "get to the bottom of this." I don't remember exactly what I did, but somehow I was persuaded by the online help, that the correct solution would be to go into my System Preferences / Print and Fax, and click on the "-", which de-installs the printer, with the idea of re-installing the printer. But then when I tried to re-install the printer, it could not find the printer. Ugh! Wierdly, it found an 8600 Scanner, but not an 8600 printers. After installing and de-installing the 8600 scanner a few times, I eventually deinstalled everything, and I decided to start from scratch. I got my HP disk, and installed all the software again from the beginning (even though it was already there), and then it looked for my printer, but couldn't find it. So then I got a USB cord, and plugged that in.
So, now I have a situation where I do have a working printer via the USB cord, but no wireless connection at all. In particular, since the Office Jet Pro 8600 won't connect to the router, I don't know what else to do. My Apple MacBook pro is 2 feet away from the printer, and it is connected to the router just fine (as is my blackberry), and I have never before had a problem connecting to the wireless router by the printer.
Any suggestions?

There are two things that can trip the mac filtering test to fail: actual MAC address filtering setup (sounds like this is not the case) and using wireless channel 6 or automatic for wireless channel in the wireless network settings (in the router). Since it does show failed for MAC filtering and you do not use this option, try changing the wireless channel in the router to 1 or 11. Those two channels provide the best compatibility with printers due to less interference. Almost everything defaults to auto or 6 for the channel and this causes a lot of interference. This change should not affect anything at all. To do this, you may need to contact the router manufacturer as the process differs from router to router.
What brand and model is the router?
Has anything in the network settings changed at all?
What version is the Mac OS X? There may be additional steps to take as it sounds like there are two separate issues involved and this could be revisited later.
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

My HP OfficeJet 6500A Plus printer/scanner/fax/copier won't connect to my wireless network

I tried going through the Wireless Network setup on my HP OfficeJet 6500A Plus machine. The printer recognizes the network and I then type in my network's password but it won't connect to the network. What can I do? I would like to be able to print and scan wirelessly. Help please!

Hello erking,
Sorry to hear that you are having an issue with connecting the printer to your Mac over a wireless connection.
I have done some research and I have found a great document that deals with The Printer Is Not Found During a Wireless Network Installation.
Please feel free to write me back and I will be happy to assist you further with any questions or concerns you may have.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

My wireless keyboard and trackpad won't connect and i can't sign in

my wireless keyboard and trackpad won't connect and i can't sign in. yesterday I tested it with my mac air and it worked fine. i deleted the connection from my mac air and tried it again. then it worded. howerver, i shut down my computer correctly and tried it again today. now the same problem again.
HELP!!

no, just a usb mouse. but I found an old usb bluetooth hardware. this made it possible for me to make it work. but as soon as I remove the hardware it says "no bluetooth available"! I re-istalled mountain lion but still the same problem.
additionally I deleted/reset the PRAM. still the same problem.

Hp C4580 printer won't connect to wireless network, but see network is available.

I've sat through quite a few of the threads here with regard to photsmart C4580 printer not connecting to wireless network.
My issues started with a cartridge issue, which I resolved with a new cartridge, but only after trying out different solution offered on HP forum.
Now printer won't connect to my network which it has been connected to for over 2 years with no issues. The wireless network is working perfectly fine and I even printed out a HP photosmart C4500 series connectivity status and in this report printer can see the network I need to connect to.
I've tried downloading various programs from Scan doctor to complete install of all HP programs and even tried installing printer from Windows 7 "add a printer", but none can see this printer.
lastly I was hoping trying to locate IP address for printer which looks like it may help, but report says IP Address "not applicable".
I believe printer, wireless network and PC are working correctly, this there a way to switch printer to online so it can be seen.
Help would be great.

Hello there! Welcome to the forums @Cushionman ,
I noticed your post about the issues you are having with connecting the printer to your network. I am wanting to offer you my suggestion that might help you out!
Click this link and then choose Windows 7, and "Solution two: Manually resolve the issue", and follow the steps from there: The Printer is Not Found During Wireless Network Installation in Windows
Let me know the results
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

I have bought the wireless keyboard for my iPad. I was working for a day but now the power light won't stay on and as such won't connect to the iPad. I have changed the batteries but still no difference.

I have bought the wireless keyboard for my iPad. I was working for a day but now the power light won't stay on and as such won't connect to the iPad. I have changed the batteries but still no difference.

Not knowing which wireless keyboard you bought, it is difficult to be specific. but ...
it is quite normal for the keyboard's power light not to stay on - it is a way of conserving battery power.
Try this:
turn you keyboard off
on your iPad go to Settings > Bluetooth
if your keyboard is listed under Devices, then touch the little blue i to its right and choose Forget this Device
now reset your iPad: hold both the Home and Power buttons down for about 10 seconds until the Apple logo appears, let go promptly when the Apple logo appears and wait another 30 seconds for your iPad to turn itself on
After your iPad is back on again go back to Settings > Bluetooth
now turn your keyboard back on and see if it appeard under Now Discoverable
if it doesn't read your keyboard guide to figure out how to put it into Discovery mode
touch the listing for your keyboard under Now Discoverable, it should now appear under Devices
touch the listing for you keyboard under Devices, and choose to pair with it.

My lightning adapter won't stuck

I got my iphone 5 today, when i first time recharged it, no problem. Now when tried to recharge it the second time, the adapter won't "stuck". It just falls out and it's loose.
I haven't used it roughly or in a agressive way.
Do anyone have any ideas how i can fix this and anyone who has stumbled opon the same problem?

You can go to the Apple Store and they'll refund you a new one.

WRT610N 5ghz xbox 360 wireless N adapter won't connect (xbox 360 "Wireless Mode = Not connected")

Similar Messages

Maybe you are looking for