WRT610N cannot open workgroup, writing to NAS causes failure

WRT610N, Laptop XP SP3 (wireless), Desktop Windows 2000 (wired), LG BD 390 (wireless), Network printer (wired), WD My Book 1 TB (NAS to WRT610N).
I had my laptop connected to my network and working fine, except, writing to the NAS would cause the WRT610N to reset. Now, I cannot view my network. I get the error, "Windows cannot access "network name". You do not have permission to access "network name". Contact your network administrator to request access." I don't know if a setting on the laptop got screwed up or what. I still have internet access, I can type in the physical address for other computers shared storage or the NAS and successfully get into them, but i cannot view my network on the laptop. I can view the network and access the NAS form the desktop. I can also access the NAS from the Blu Ray player. I have tried turning off all of my firewalls, i still get an error.
Also, anytime i write a larger file (bigger than a document) to the NAS, the router power cycles. I cannot use my NAS for back-up because of this issue. Can anyone help? If more information is needed.

As the router reset,when you try to transfer the larger file,I would suggest you to upgrade/reflash the router's firmware and reconfigure the router from scratch...You can download the firmware from www.linksys.com/downloads.Before upgrading the router,unplug the HDD from the router.
On your laptop,remove all the preferred network,add the wireless profile and map the drive again on the computer.

Similar Messages

When Firefox freezes and reboot is needed, Firefox always tries to open the same tabs that caused failure before.

I use tabbed browsing all the time. When I open a tab to a website that causes a problem, freezing Firefox (but not the computer) I usually find that I can clear the Firefox problem only by rebooting the computer. I am then dismayed to find that Firefox then tries to recreate the same set of tabs that caused the problem in the first place, causing Firefox to freeze a second time. Usually I can get out of this by closing Firefox and waiting a very long time for Firefox to fully close so that it can be restarted again.
This problem happens in version 4.0 as well as in the last version of 3 that I had. I recall that in some earlier versions Firefox would ask if you want to recreate your tabs or open as a new browser window. I always took second option. That choice is no longer appearing.

Set the pref [http://kb.mozillazine.org/browser.sessionstore.max_resumed_crashes browser.sessionstore.max_resumed_crashes] to 0 on the about:config page to get the about:sessionrestore page immediately with the first restart after a crash has occurred or the Task Manager was used to close Firefox.
That will allow you to deselect the tab(s) that you do not want to reopen, but will allow to reopen other tabs. 
See:
* http://kb.mozillazine.org/Session_Restore#Restoring_a_session_after_a_crash
* http://kb.mozillazine.org/Browser.sessionstore.max_resumed_crashes
To open the about:config page, type about:config in the location (address) bar and press the "Enter" key, just like you type the url of a website to open a website. 
If you see a warning then you can confirm that you want to access that page. 
You can use the Filter bar at to top of the about:config page to locate a pref more easily.

IPhone - MainWindow.xib - ibtool cannot open files of this type

Hi,
I'm trying to compile the sample MoveMe application and cannot get it to compile. I get the following error:
Description: "MainWindow.xib" could not be handled because ibtool cannot open files of this type.
Failure Reason: ibtool cannot open files of this type.
I have installed the beta3 version of the SDK. I'm new to building iPhone apps, so I may not have supplied all the required info to solve this issue.
Interface Builder - version 3.1 (644)
XCode - version 3.1 (Beta)
I tried using "Active SDK" as "SDK at iphoneos2.0" but it couldn't find it:
error: There is no SDK with specified name or path 'iphoneos2.0'
so I am using "Simulator - Aspen 1.2"
Thanks for any help.

anymore updates on the topic ? done that and still getting the error...
Building target “WhichWayIsUp” of project “WhichWayIsUp” with configuration “Release”
Checking Dependencies
CompileXIB /Volumes/WhichWayIsUp/en.lproj/MainWindow.xib
cd /Volumes/WhichWayIsUp
"/Volumes/14/iphone sdk dev tools/usr/bin/ibtool" --errors --warnings --notices --output-format human-readable-text --compile "/Volumes/14/iphone dev/whichwayisup/Release/WhichWayIsUp.app/Contents/Resources/en.lproj/MainWindo w.nib" /Volumes/WhichWayIsUp/en.lproj/MainWindow.xib
/* com.apple.ibtool.errors */
Internal Error:
Description: “MainWindow.xib” could not be handled because ibtool cannot open files of this type.
Failure Reason: ibtool cannot open files of this type.

I cannot open my firefox broswer. The message box appeared that said a problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available. Under that there are debug and close program buttons.

I cannot open my firefox broswer. The message box appeared that said a problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available. Under that there are debug and close program buttons.

JackieMars71 I would recommend reviewing your installation log files to determine if there are any errors during the installation process. You can find information on how to locate and interpret your installation log files at Troubleshoot install issues with log files | CC - http://helpx.adobe.com/creative-cloud/kb/troubleshoot-install-logs-cc.html. You are welcome to post any specific errors you discover to this discussion.

Cannot open file for writing...

I keep getting this error...
Cannot open "filename" file for writing. Please check the output filename and file permissions (if it already exists) and then try again.
Not sure what is going wrong here. I have scoured the web and can't find a solution.
Running CS5 on a Mac.
Any help is appreciated!!

This might indicate a problem in AME CS5, but we'll need more information about the clip--and possibly a copy of it--before we can make that judgment.
If the clip plays on Computer X but not on Computer Y, that could indicate that X has a certain codec that's missing on Y.
What codec is the clip? What's the extension of the filename (which equates roughly to the type of wrapper)?
What are the origins of the clip? (e.g., is it straight off of a camera? or was it encoded by another program?)
Do you have AME 5.0.1 installed on both computers?

Dynamic Send Port : The FILE send adapter cannot open file C:\Temp for writing. Details: Access is denied.

Hi All,
We have requirement of using ESB toolkit and transforming incoming xml file to edi format. So, we are using ItinerarySelectReceiveXML pipeline for receiving the input from the input location and "EDISend" pipeline for transforming it into EDI and
send it to destination.
Now, the receive pipeline is picking up the file, but it is not processed and sent to destination.
And, we are getting an Access Denied error from Dynamic send port.
Error Description :
The FILE send adapter cannot open file C:\Users\Public\Temp for writing.
Details: Access is denied.
Any Immediate solutions/suggestions are appreciated...Thanks.
Anand

The difference between dynamic and static port would be send handler. For dynamic port, default send handler will be used and for static port the one configured on the port will be used, could you validate this configuration.
Also sometimes, administrative privileges are not "real" administrative privileges and company admins will have limited permissions on C Drive folders. Try writing to some other folder to isolate the issue.
Regards, Ajeet Kumar MCTS Biztalk Server

I recently updated to the OSX 10.8.3 Operating Sistem. I am writing a book and now cannot open any word document I've created. Could not find a newer version of the Microsoft Word Processing Program. Is Pages the next thing? Can I recover my documents?

I recently updated to the OSX 10.8.3 Operating Sistem. I am writing a book and now cannot open any word document I've created with the old system. Could not find a newer version of the Microsoft Word Processing Program. Is Pages the next thing? Can I recover my documents? How?

I'm in the same boat: new to OS X and Mac, and in the middle of a book. I switched because I heard about the the ease of using Mac, but so far, for me, it's been a nightmare. I bought 2011 Office Mac and hate everything about it, the most recent being the inability to open or cut or paste any of my original word files. I understand that this could have easily been done with earlier versions, but not Mountain Lion (which I learned is what OSX is.) Since I work with language, I am amazed at the assumptions of the Apple community. It helps to use common language and explain even the basics.
So all the helpful hints to use the latest version of Office Mac are to no avail. Now what?

My iMac will not shut down cause it says my mail is open but it is not and i cannot open it from the bottom of the screen don't know what to do

my imac will not shut down cause it says my mail is open but it is not and i cannot open my mail from the bottom of the screen

Hi there, go in to the utilites of you applications folder and find "Mail" then go stop processes.
If you cannot find Mail then open mail up and follow the process as above.
Thanks an Appple Certified Mac Technician Trainee

Ive got this problem with itouch 4th gen when im trying to upgrade my ios to ios 6.1.3 when it is verifying it suddenly shutdown and it keeos on blinking with the logo and i cannot open it...what is the main cause of thst..tnx

ive got this problem with itouch 4th gen when im trying to upgrade my ios to ios 6.1.3 when it is verifying it suddenly shutdown and it keeos on blinking with the logo and i cannot open it...what is the main cause of thst..tnx

- Reboot the computer
- Try DFU mode and then restore/update
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- Delete the update file so that new one has to be download.
IPSW file location for Mac and Windows
- Try on another computer to help determine if you have an iPod or computer problem.

Cannot open the Microsoft Jet engine workgroup information file

Hi,
I have 4 linked servers in a SQL Server database. One of them is another sql server database. This one works fine. I have 3 that are Access databases. Last week I could run a query against these linked servers, but now when I open SQL Server Management Studio I get something like the following:
OLE DB provider "Microsoft.Jet.OLEDB.4.0" for linked server "HRDB" returned message "Cannot open the Microsoft Jet engine workgroup information file.".
Msg 7303, Level 16, State 1, Line 1
Cannot initialize the data source object of OLE DB provider "Microsoft.Jet.OLEDB.4.0" for linked server "HRDB".
What does this error mean? I've looked at several posts, but none apply to my problem. I've looked to make sure there wasn't a .ldb open. Anything else I've missed?
Many thanks,
Mark

The key error is "Cannot open the Microsoft Jet engine workgroup information file". Here is a suggestion from a AccessMVP.
Are you using ULS (User Level Security) in Access, with a custom workgroup
information file (*.mdw)? If so, you may need to replace this file using a
copy that you should have backed up.
If you have not specifically implemented ULS, then you're still using it,
but you are joined to the file named System.mdw, with username Admin and a
blank password. In this case, which is more likely than the above case I
guessing, your copy of System.mdw may have somehow gotten corrupted. Try
searching your hard drive for this file. For example, my copy is in this
folder:
C:\Documents and Settings\Administrator\Application Data\Microsoft\Access
(Yes, I log on as Administrator on my PC routinely. Bad Tom).
Rename your copy of System.mdw to something else. Then try restarting
Access. Access 2003 will automatically create this file, if you are
permanently joined to System.mdw, and it does not find it during startup.
That should get you a fresh copy.
Good Luck,
Tom Wickerath
Microsoft Access MVP

I cannot open gmail. It is showing this:- "This problem can sometimes be caused by disabling or refusing to accept cookies."

See: [[/questions/1059115]] (locking)
I cannot open gmail. It is showing this:- "This problem can sometimes be caused by disabling or refusing to accept cookies."

Clear the cache and remove cookies only from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"
You can inspect and manage permissions for the domain in the currently selected tab via these steps:
*Click the "[[Site Identity Button|Site Identity Button]]" (globe/padlock) on the location/address bar
*Click "More Information" to open "Tools > Page Info" with the Security tab selected
*Go to the Permissions tab (Tools > Page Info > Permissions) to check the permissions for the domain in the currently selected tab
See also:
*https://support.mozilla.org/kb/Deleting+cookies
*http://kb.mozillazine.org/Cookies

Possible cause of "Cannot open Excel file error"?

Hi!
Here's my problem: one of our LabView applications creates .xls Excel
files. However some of these files are too big to be opened into
Excel, so we need to open these files in DIAdem to analyse the data (in
fact, even the smaller ones often need to be analysed in DIAdem).
The problem is that DIAdem seems totally unable to open Excel files,
small or big, created by our LabView application or not. The
error message appearing when we try to import Excel files is "Cannot
open Excel file"... which doesn't give any clue about the cause of the
error. My question is: what may cause this error to
occur? I searched both the help and the website without finding
useful information.
The computer is running on WinXP with OfficeXP installed, and we are
using DIAdem 9.0. If additionnal information is required, just
let me know.
Thanks in advance!
Maxime B.

Hi!
I did some experiments this morning. First of all, the file I had
created using Excel that I tried to open yesterday just opened. I
don't know why it didn't work yesterday, but, for now, it's
working. Now, for my LabView-created files, I still get the same
error message. However, if I open the files in Excel and try to
save, a warning message appears, saying that the file may not be
compatible with the text (separator:tabulation) format. If I
ignore the warning and save the file as a .xls file, I can now import
it into DIAdem. The problem is probably that my LabView-created
files are not "real" .xls files. Now, this is a problem, because
I can't open some of the bigger files in Excel without having the data
truncated (Excel has a maximum of 65536 rows); last year, using DIAdem
8.X (I don't remember the exact version we had), I could open those
files without any trouble... Is there any way to get those files to be
opened with DIAdem 9.0? I attached one of those files if it may help.
Thanks!
Maxime B.
Attachments:
Data1.xls ‏152 KB

What causes "report could not be opened for writing . . ." message

"This report could not be opened for writing. Any changes must be saved to a new file." The version is CR 2013 SP1. Win 7 Pro. I'm new to CR and can't figure out why I get this error. I've verified all Windows permissions. It's an SAP error message - not a Windows message. Thanks in advance.
rd

Hi Rd,
Per SAP Note 1911880, this has been identified as a Bug in CR 2011. Since CR 2013 is just a rebranded version of the same tool, the SAP Note should apply to CR 2013 as well.
For CR 2013, the issue has been resolved in FP3. I would suggest you to upgrade to the highest available version for CR 2013 and see if it works.
Another workaround could be to right-click the CR Designer exe > Run as Administrator > Log-in with Admin credentials > try opening the report.
-Abhilash

Getting error 'Cannot open your default e-mail folder' in Exchange server 2010? what are common causes?

I'm getting error
'Cannot open your default e-mail folder' when try to access my email account on exchange 2010? Why I am getting this error? Is there any particular reason? And how can I manually fix it? plz suggest!!

Hi,
Some questions:
1. Can you open your account via OWA?
2. Can you configure your account on other user's computer?
Try disabling any 3rd-party firewall or AV programs, make sure no proxy applictions or settings.
Thanks,
Simon Wu
TechNet Community Support

Very slow access to NAS causes Finder to crash

Hello,
I have a mid-2011 iMac with Yosemite connected to my tp-link router WDR-4300 via WiFi. Everything works fine, internet browsing etc. I bought a Synology ds213air NAS, connected via LAN to the same router. When I access the NAS from the iMac the connection works ok and the streaming speed is also fine if I try to watch some movies stored on the NAS for example, but when it comes to browsing the content of the NAS folders it's a disaster. The browsing is really slow, and often Finder gets stuck and I completely lose control of the iMac (I have to reboot). Reason why I am writing here is because if I access the NAS from Windows everything works perfect. Even worse, the Windows 7 copy that I am using is installed on my Mac using Parallels... So it is not an issue with the WiFi or the network environment, it is purely an issue with the iMac/Yosemite. I have been having exactly the same issue even before Yosemite, with Mavericks, Mountain Lion and Lion. Everything has the latest Software/Firmware installed. I access the NAS by using afp://<ip address> on the Mac.
I am out of ideas, would be good if someone experienced the same issue and knows more about this.
Thanks

Same problem with a 2014 Macbook Air and a WD 4tb Mybook live duo. I also have a win 7 basic laptop.
Don't know if this ill help but it was suggested you need to mount the shares at startup. The problem most have found is that if you just add the share to login items it always opened a finder window. I also have a windows 7 machine and with my wd live book duo it is lightning fast the new Macbook is like a week week. This is as far as I have gotten still looking for help and ideas Apple no help.
Partially Solved
Ok my windows 7 machine still accesses all folders (no matter how many levels down the tree) and files extremely fast but with my partial solution below the MacBook with Yosemite is better but still a poor cousin
After reading a lot of similar questions dating back to 2008 I decided to copy some lines of a script to mount network folders, from that I was able to white cane myself through how scripts work until I came up with the following script
After writing this in Script Editor I saved as an application into the APPS folder. From there I dragged it into Users login items. As a script it seems to work perfectly. Does it do what we need?
Mostley.
I struck a problem copying from one network share to another with a response stopping me saying you don't have permission to do this. When I looked at get info I wasn't able to get any as I was logged in as a guest and wasn't logged in with privileges to my NAS Drive.
So I added the login/password to my router (workgroup) before the nas drive name and shared folder name. This seems to have worked as far as editing and copying files etc. but when I 'get info' on the mounted drives it still shows custom access and does not allow me to change user access.
Speed of access. Shares with a mixed of files about a one to three second delay, Photos and music sometimes still up to 20 seconds delay to see files and these delays continue as you click through the lower folders.
Debatable, now much faster than before and nearly tolerable, but till nowhere near the speed of the windows 7.
So I am missing something here. It seems obvious to access a nas drive with yosemite you need to use a script or have some startup configuration code run that suits your network.. This is far beyond my knowledge, but really it shouldn't be needed at all if apple had got it right to begin with.
Anyway over to you with knowledge what am I missing?
Why is it so damned slow still
The following script mounts the various shares at startup and has a small delay to allow the wifi to connect before telling finder to mount the network shares, These share mount then because I want to see they have mounted I put in 2 second delay before telling finder to not show connected servers on desktop.
Change names and password and number of shares to suit your setup then save as an app and add to user login items
good luck, hope you do better than me
Network Start Script Yosemite 10.01
>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
delay 10
tell application "Finder"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
mount volume "smb://Router;admin:xxxx@Network/name"
delay 2
set desktop shows connected servers of Finder preferences to false
end tell

WRT610N cannot open workgroup, writing to NAS causes failure

Similar Messages

Maybe you are looking for