WRT610N Connection issues

Looking for a bit of advice to see if anyone else has encountered the same.. The WRT610 has been working rather well now for about 9 months since i purchased it.. Then just the other day it stopped working.. Not entirely, only with the wan portion.. i can unplug the wan connection and connect that straight to my PC with no issues.. I’m back up and running in less than 20 seconds.. I plug the connection into the WRT610 and i never acquire an IP address.. I have upgraded the firmware to the latest as of Yesterday, i have reset, factory reset, used the reset button on the back and still have the same issue.. Router just will not acquire a DHCP address from the wan.. There are times it will get an address, this usually comes after about 2 hrs of working with it but then it only works for about 5 to 10 mins then back to the same thing.. Its lost the address again.. Any ideas?
Message Edited by achillicm on 07-27-2009 07:50 AM
Message Edited by achillicm on 07-27-2009 07:57 AM

After resetting the Router you need to re-configure the router accordingly(depends upon your ISP)...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link
To re-configure your Router you need to use a desktop computer(don't use a Wireless Computer)...

Similar Messages

WRT610N connectivity issues

I am not sure what caused this, but I started having problems with my WRT610N recently. This is a dual band router that puts out a 5Ghz and 2.4Ghz network and I never had any trouble connecting to either of them until last week. Suddenly, I found I was unable to connect to the 2.4Ghz network but the 5Ghz was fine. I had made no changes to either network; both were still on exactly the same settings.
I did some troubleshooting and discovered that I was able to connect to the 2.4 when it was insecure. I did further testing and discovered I could connect to it with a WEP encryption but it was when I set up the WPA that I could no longer connect. Strangely, the 5Ghz is still on the WPA with the same password and I am able to connect to that one fine.
Does anyone know what is going on here? It is not as important now that I am able to bypass the problem by using WEP, but I am still wondering what changed and what can I do to get it back to normal. Thanks!

Try to reset and reconfigure the router .
Press and hold the reset button for 30 seconds .
Power cycle the modem and router .
Open the setup page of the Linksys router .
Configure the settings manually on it .
Also create a new wireless network do not use old wireless name .
What is the current firmware version on your Linksys router ?

WRT610N v1 connection issues, media center and internet

Good evening. I am having a connection issue with my wireless/wired connection and am wondering if anyone else has had the issue.
I am running the following
WRT610N V1
Firmware Version: 1.00.03 B15
Windows 7 Enterprise Edition
I have an Xfxforce 780i motherboard with onboard dual 1gb nics plugged into the router.
I am also using an Xbox 360 Wireless N device.
The issue i have been having recently are two, both seem to be router related. Sometimes while gaming or on the web I will losing connection to my gateway. I have both of my nic mac addressed reserved in the router. On my windows 7 machine the internet connection will stop working and I will have to repair the connection.
The issue i have been experiencing with my Xbox 360 is sever choppiness while streaming recorded tv shows over my network
For the most part while I am streaming the video's i am doing nothing else, it should be noted that i can watch the vidoes on the PC without an issue so the issue shouldn't be pc related. I initally though maybe resource related but the vidoes run fine on the pc. Restarting has no effect.
I did do a hard reset on my router but that did not solve the issue. The issue is semi random but the frequence is fairly higher. Sometimes I will get through a full show or two and sometimes the quality of the steam will be horried. Where pausing and restarting won't do anything.
I have used a direct wired connection and I still get the video degredation so I believe the issue is my access point.
For the price that i paid for this unit, $200 - yes i did say 200 as it is a V1 model and i got it when they came out, this is one of the worst issue I have ever had.
I am going to test a netgear 54g tomorrow night to see what experience I get.
I did some poking on the forum here and I noticed others have had some degredation issue but nothing seem to solve it even though their threads are marked as solved. I have tried turning off windows 7 firewall and disabling my AV to make sure those weren't the issue, which they aren't.
It should be noticed that my machine is the following and I am fairly sure the issue isn't pc hardware related.
win7 pro
xfx force 780i
intel e8500 dc 3.16
evga nvida 9800 gtx ssc
seagate dual 250gb raid 0 hard drive
4gb g.skill pc8500 ram.
I am adding more ram later this weekend to take it to 8gb and a new 1tb drive to transfer my media center data too. I do not believe this will fix my issue since the only issue I can see is the Linksys router.
thoughts?

Try these things, in this order:
1. Disable Home Defender.
If that does not work, try
2. Reducing MTU to 1300 (recommended by someone else on here for a throughput issue). This may not be relevant to you, but it doesn't hurt to try. MTU settings don't generally apply to in-network connections. But who knows what's what when it comes to this router.
3. Disable Upnp. Some people, like myself find this setting necessary - but you may want to just go ahead and disable to see if that helps.
4. You need to remove the name of the competing product (that router) from your post. I got banned from the forum for a few days for mentioning that I was using so and so router for the time being. Do it before the post is deleted or you're banned.
Good Luck. Let us know if anything here fixes your problem.
Remember that you'll need to give the router 'time' with each fix separately. Don't do all 3 things. Do 1 at a time and give the router a few days, to feel out if the solution works or not.
Good Luck.

WRT610N/2.4GHZ Connection Issues

I have had this router for about a month and a half no problems to speak of.
From one day to the next the the 2.4 side of the router started having connection issues.
It has become extremely slow and unresponsive at times. I have unplugged the router. Did not help.
No configuration changes or environment changes within the house.
I have tried changing some of the options for the 2.4 side of the router. Still having the same issues.
The 5GHz works fine, I have had to switch several computers in the house over to the 5GHz side.
I have the version 1 of the this router and the most current ,firmware 1.00.03 B15.
All the computer on the network are windows based XP to Vista.
Any ideas would be greatly appreciated.

Try to do the following changes for 2.4GHz on the router...
Set the Radio Band to Wide-40MHz and change the Wide channel to 9 and Standard Channel to 11-2.462GHz and click on save settings...Under Wireless tab,click on Advance Wireless Settings,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2307 and Click on Save Settings... Under Security tab...uncheck "Filter Anonymous Internet Requests " and click on save settings...

WRT610N connection speeds

I have V2 with the latest firmware on my WRT610N. It keeps losing internet connection speeds. Sometimes an IP release/renew will fix it. If it does, It will be ok for a day and then it goes back down to 1.0 mbps. I've tried a couple things I've found in this forum like turning off upnp and restarting but that hasn't helped. Maybe I didn't do it right though. Any ideas? Please help!!

I have seen this as well. This only seems to be a wired connection issue as I read others with the same complaints on this board. I have a WRT610N v.2. I have a new Alienware Area 51 ALX (fast) and I upgraded to this gigabit router. I can actually track the slowdown using www.speedtest.net from almost 15 down to about 3 in the course of a day. A router reboot returns the speed. I also posted an issue with with a wired connection to my PS3 losing UPnP availability. The fix for that was a reflashing of the firmware, but it seems that the only thing I would have needed to do is reboot the router as it showed up as unavailable again and I rebooted to router and it is available again.
I have sent this to Linksys tech support as well. With as many people having this issue I hope they are already aware.
there appears to be a fix using a third party firmware update dd-wrt. But I am not going that route just yet.

HP PhotoSmart 7510 suddenly has severe connectivity issues

I have a HP PhotoSmart 7510 printer since about 2 months. Initial setup worked like a charm and the printer has been working pretty much perfectly for the last 2 months. Wireless printing, scanning and internet access on the printer (e.g. for Facebook photos) all worked. Just from time to time i would get the occasional (mildly annoying) message on my computer saying "scan to computer is currently unavailable" but it usually worked itself out and whenever I needed it to work, it did work.
But since a few days ago, it has some severe connectivity issues. I didn't change any settings on the printer, router or computer - the issues just started appearing by themselves. I startet getting much more frequent messages on my computer saying "scan to computer is currently unavailable". I noticed I couldn't print anymore, and restarting computer, printer and/or router didn't help at all. The only thing so far i managed to print wirelessly since the problems started were the first 5 pixel rows of an image I tried to print, the rest didn't transmit.
It seems the printer still connects to the WLAN but printing and scanning no longer work, and whenever I try to access a web service on the printer (like Facebook) it says it has no internet connection, even though the WLAN light is lit up (not blinking) and all the wireless status reports say "congratulations, no problems found" and display IPs etc. just like normal.
I looked at the threads "PhotoSmart 7510 connects to router, but not to the web.", "Wireless printer (HP Photosmart 7510) not connecting to network" and "Photosmart 7510 won't connect to Web Services" but they weren't a big help. Activating EWS didn't work because even though the printer showed its IP address to be 192.168.1.3, when I entered this in my web browser it didn't find the printers configuration page.
I tried the following steps from one of the threads:
1. Restore the Network defaults
2. Unplug the printers power cord while it is still on. Leave it unplugged and walk to the router.
3. While the router is still on, unplug the power cord from the router, leave it unplugged for 30 seconds, then reconnect the power cord to the router. Once plugged back in the router should power on automatically.
4. Plug the power cord back into the printer. Once plugged back in the printer should power on automatically.
5. Run the Wireless Setup Wizard to reconnect the printer to your wireless network.
6. Try enabling Web Services.
I followed these steps exactly. Interestingly, even though I had done step 1 and restored the network settings to factory defaults, after turning back on, the printer somehow still had its old settings saved and reconnected to the network.
It seemed to have fixed the problem, the printer finally had internet access again (Facebook app showed my photos) and scan to computer found my PC. But after just about 3 minutes, the printer had lost its internet connectivity again. When opening the Facebook app, it displayed the same error message it did before. And printing no longer worked as well.
So, what is wrong with this printer?! It has the newest software update by the way (I checked during the 3 minutes it had internet access.) My computer is a HP Windows 7 x64 machine (EliteBook 6930p) and the router I'm using is a Netgear WNDR3700.
I specifically bought this printer for my studies at university. In one week i have my exams and in order to study I REALLY need to be able to print some of my course materials! So any help as quickly as possible would be greatly appreciated. Or do you think this is a case for a warranty replacement, considering the printer's really strange and error-prone behavior?
Thanks a lot!

I can assure you that it is not a router issue. It appears to me that it is a driver compatibility with Windows OS. After trying to get to the bottom of this since my Photosmart 7525 was new and reading just about every forum and blog, I have come to the conclusion that the issue must be related to the HP driver itself.
The issue does not seem to affect any Mac systems, and from one forum someone was able to fix it by downloading new drivers compatible with 64-bit systems (which seem to not be affected by the glitch). But that leaves us 32-bit people stuck with the current driver which does not work.
The printer is connected with good signal to the wireless router (no matter who's router it is and what configuration is made). The printer can be pinged from the router and any computer on the network which is not currently being affected by this issue. However, the affected computer fails pings by either request timed out, or destination host unreachable. Pings are successful from the affected computer to any other device on the network. The only way to recover (at least for a few days) is to reboot the affected computer.
Also, from the display on the 7525, the network tests pass without issue. I can also download and print content from the internet with no issues.
Please do a quick google search of this issue and you will see several THOUSAND entries of people with the same request. This is a serious issue that people are having and everything is pointing to an HP problem (not routers, improper installation of software or drivers, etc...). I agree with several other customers that HP should be on the hook for this fix. I will give it another couple weeks, then back to the store for a reliable unit from another competitor (Canon, Lexmark, etc..)
Thank you in advance for escalating this issue to product engineering,
S. Hunn
There are 10 kinds of people in this world... Those who understand binary and those who do not.

Connection doctor and connection issues

I have nothing blocking my internet connection, however mail is a nightmare for me. I continually receive connection issues via the connection doctor for imaps, pops, and icloud.
Are my settings wrong? I have checked with each of the settings and they are set per instructions provided. Some are google, some yahoo, icloud, etc.
This is really annoying and I could really use some help.
Here is a typical message: Could not connect to this Google IMAP server. Check your network connection and that you entered the correct information in the Account preferences. Also verify that the server supports SSL. If it does not, deselect the 'Use SSL" checkbox in the Advanced tab of Account Preference"
I have done all of this and am still having troubles.
I am also receiving SMTP connection issues - "Trying to log into this SMTP account failed. Verufy that the username and password are correct."
I have checked and all are correct. Even more confusing, these issues are not present all the time - however I have not changed anything between when times are good and bad.
Sigh - I hope someone has an idea to help me out.
Thanks in advance for your time and thoughts.
Patti
I am running osx 10.8 mail 6.2 and use xfinity for my internet (as I mentioned, I disabled their firewall trying to fix this)

Hi there Japps1,
You may find the troubleshooting steps in the article below helpful.
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/TS3276
-Griff W.

Excel ODBC Connection Issues

I'm having some issues importing external data from an Oracle 9i database.
Here is what is happening:
I am initially able to import data from the table I want to into Excel.
I do this through "Data -> Import External Data -> New Database Query" where I have my .ORA data source. I'm able to log in using my user and password and import the table. My problems come after I import this first set of data.
If I try to "Edit Query…" I get an error box that says "[Microsoft][ODBC Driver Manager] Driver's SQLSetConnectAttr failed".
If I try to "Refresh Data" I get two error boxes. The first is just: "[Microsoft][ODBC driver for Oracle][Oracle]" and the next says: "[Microsoft][ODBC Driver Manager] Driver's SQLSetConnectAttr failed". It then prompts me for the User name and password of the DB I'm connecting and after I enter the information, I get the same two error messages.
Also, if I attempt to establish another connection following the "Data -> Import External Data…" steps I run into a different problem. Upon entering the information for the User Name and password prompt I get two error messages. One says "!" and the next box says "Couldn't read this file". Once I click "OK" in those boxes, the Microsoft Query window automatically opens with nothing in it.
I can't seem to figure out why I can initially pull down data and then cannot succeed afterwards. I'm unable to connect to the DB I have through Excel until I completely closed all Microsoft Excel instances.
I also use this data source in Microsoft Access without any problems.
My Excel version is 2003.
I'm using Oracle Drivers I'm using are from an "Instant Client" package.
Any thoughts why I'm having these connections issues?
Thanks in advance.

This issue is closed.
The solution was:
"Data -> Import External Data -> Import Data"
Select "New Source" and select the "Oracle" data source and filled in the appropriate information. This was similar to the database query but it actually works.

My brand new mac pro always had Internet connection issues at school. WHY is that? I see the school's Internet working perfectly fine on other PC's, but there is never a day where my mac doesn't have Internet connection issues at school. How do I fix it?

I got my mac pro in the middle of August. School started the week after. Internet was working perfectly fine at home. But at school, I never had a good connection. Sometimes on the good days I get a connection when I'm sitting at the exact spot in class I always sit at. It's ridiculous and it's frustrating. I invested my money into this laptop and I'm beginning to regret it. I thought it was the school's Internet, but I don't see Internet issues with other PC users. It's most frustrating on registration days and I'm trying to register for my classes before it gets taken, but again... Internet connection issues. It's random. Majority of the time, it doesn't work at all. I've done Network Diagnosis and turning WiFi off then turning it on again. I've done everything I could. I put my money on this laptop and it was a lot of money. I could have bought an 800 dollars laptop and I would have Internet connection anywhere on campus. So, I don't want to continue everyday to regret on buying this laptop every time I try to connect to the Internet at school or Starbucks or anywhere else. How do I fix this? What's the problem ?
At school, I heard this guy had a problem with Internet connections too and he owned a new mac book pro. He said something like Apple messed up on something, but he fixed it. If I knew mac book pro's had these issues I wouldn't have bought it in the first place. It's freezing on me every other day. It's ridiculous. But what concerns me the most is the Internet connection. So someone please tell me what can I do next to prevent the problem? Am I doing something wrong maybe?

Hi Kevin,
I'm using an XLR input mic which is connected to the phantom power enabled XLR mic socket on a USB M-Audio M-Track. The M-Track is connected by USB to the Mac Pro - so effectively I've got an M-Audio USB soundcard with a mic input. I've also tried a microphone that is a straight XLR to USB cable (guessing with some soundcard chip buried in the usb plug) but that also yields the same effect of bad latency, intermittent quality, stuttering and repeating and echoing (without the speakers on during record so its not feedback).
The mic works absolutely fine with other recording applications I have on the mac at the moment - albeit non-adobe ones (tested it on the EasyAudioRecorder - and it lives up to its name. it's easy)
I will try with Audition and report back, but sitting here right now I can imagine it would work fine with audition too - it just seems to be the way premiere is set up for recording into the timeline is a bit sketchy. I'm willing to accept it might well be a quirk with the new Mac Pro trashcan - I'm not weighting all the woes on premiere.
Any thoughts or am I out of luck to sit with my fingers crossed for a fix in the next round of updates?
Nathan.

Connection issues with Safari 3

I'm having some connection issues with Safari 3.
When I connect wirelessly, Safari won't load any web pages. I go and use Firefox and everything is just peachy.
I've reset Safari, emptied the cache and whatnot. I went in and checked the permissions, everything checks out.
When I connect with Ethernet, there's nothing wrong, which is my dilemma.
Help would be greatly appreciated.

There are a number of posts in the Leopard forum from people with direct experience with upgrading from Panther to Leopard. Here is a relevant thread from there that should reassure you.:
http://discussions.apple.com/thread.jspa?threadID=1418714
Your system should be fine for Leopard, but you will probably need a current version of Photoshop if you don't already have it. See this download:
http://www.adobe.com/support/products/pdfs/leopardsupport.pdf
Also, Leopard doesn't run Classic (OS 9) apps.
One caveat - first make a bootable backup "clone" of your present system onto an external firewire drive so you can recover if anything goes wrong. You can use the "Restore" tab of Disk Utility to make such a clone, and there are also Panther-compatible versions of Carbon Copy Cloner (v 2.3) and SuperDuper (v 2.1.4), both excellent for this.
It's even possible to a create second Panther clone on a different external volume to create a "dual-boot" system, using that volume to continue to run old applications that you can't run with Leopard.

Connection issues with EA4500

I had bad connection issues with my mobile device, so i pressed reset on my EA4500 router, and now when i connect to my network, it gives my limited connection even though i have 5 bars of signal. Not sure what to do now...

Resetting the router will erase all the settings you configured on the router since the initial setup. You manually configure the router's wireless settings so your wireless devices can have internet access again.
Procedure: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=cfb50c0dc992443ab2405a782cca60f7_19073.xml&pid=80&...
Make sure to use a computer that is hardwired via Ethernet cable to the router.
For bad connection issues: http://kb.linksys.com/Linksys/ukp.aspx?vw=1&docid=cf6ed888ce144d06905af4987887fd1b_KBxxxx_EN_v1.xml&...

X1 Carbon (20AX series) wifi connectivity issues

Dear Lenovo Support and all others,
I am posting this in hope that someone can help with my problem and also to share my unpleasant experience with a new Lenovo product.
Lenovo Thinkpad X1 Carbon
Model: 20A8A00VSG
OS: Windows 7 Pro 64bit
Purchase date: 27th February 2014
Since the first day I purchased the system, I have been having an issue with my wireless connection:
1. I am unable to reliably get a wireless connection to wireless access points (e.g. free wifi coffee outlets or malls) and personal mobile hotspots (mobile phone hotspots). It constantly says "LIMITED CONNECTIVITY". In other words, I cannot get internet access. Even when it does connect to the network and get internet access, there is a tendency for the connection to drop back to "LIMITED CONNECTIVITY".
The only time I can get a reliable connection is when I am connected to my home wireless router. The system does not seem to have problems on home wifi networks. Since the problem seems limited to wireless access points and hotspots, I believe its a hardware/software problem.
Please note that I have other wireless devices (laptops and mobile phones) that can connect to the same networks that I am trying to connect to and have no issues.
I have tested the networks with my friends' wireless devices as well and they have no issues accessing the internet so I am fairly certain that there is no issue with the networks themselves.
2. I have already called in twice and been given advice on both occasions but the problem still persist. I have updated all drivers, uninstalled and reinstalled and updated the BIOS for the system and also performed a system recovery but nothing has worked so far.
I have also tried disabling and/or deleting any anti-virus software and firewalls but it does not fix the problem.
I have also been advised that I need to go down to the Lenovo service center to have my laptop checked out by the technicians and that there MIGHT be a firmware upgrade for the wireless card itself.
NOTE: MIGHT? The support staff doesn't even know for sure whether there is an upgrade available.
3. Rebooting my computer, the wireless card or the hotspots does not solve the problem. It might work for a shortwhile before it reverts back to it's non working state or stops working again once I reboot the system.
I am really unhappy with the purchase so far. It's actually a good laptop per se when all is working, but without internet access, it is pretty much like a dead fish. And thats 90% of the time.
Like I said, this problem has been happening since day one and I've tolerated it long enough.
I hope someone can help me with this problem.
Thanks all.
UPDATE - 3/24/2014
I borrowed an ASUS Wireless USB adapter from a friend and installed it on the laptop. Lo and behold there are no connectivity issues to my iPhone wireless hotspot.
INTEL DUAL BAND WIRELESS AC 7260 - NO CONNECTION/LIMITED ACCESS
ASUS USB N10 WIRELESS ADAPTOR - CONNECTIVITY AND INTERNET ACCESS
I think this narrows it down to the software/hardware in the computer....

Hi, all
there is an issue bugged driver or even card firmware related. Intel confirmed that. Wait some time for the new release.
For the test purpose only disable 2,4 ghz band support and switch to 5 ghz. N-band seems unstable so switch to G-band. As the Linux users report the same issue it's firmware bug basically.
x220 | i5-2520m | Intel ssd 320 series | Gobi 2000 3G GPS | WiFi
x220 | i5-2520m | hdd 320 | Intel msata ssd 310 series | 3G GPS | WiFi
Do it well, worse becomes itself
Русскоязычное Сообщество English Community Deutsche Community Comunidad en Español

Macbook air Mini DisplayPort to VGA Adapter connectivity issues

Hi pple,
Would like to ask if anyone is facing connectivity issues with Mini DisplayPort to VGA?
I am currently using the 2nd Gen Macbook Air with Intel HD Graphics 3000 384 MB. Sometimes when I connect to a montior (Viewsonic VA1918wm) it works fine, sometimes it just does not work and the laptop just shows me a blue screen.
I tried with out with my friend's Mini DisplayPort to VGA adapter, it has the same problem. Does this means that my macbook air mini disoaly port got a problem?
Thanks
Bryan

I am experiencing the same kind of problem... only with projectors. Some projectors will display the screen and then others wont even register with the MacBook Air.
Using an Apple Min Displayport to VGA adapter. It's hit or miss if it works. Firmware has been updated on the adapter but this did not help.
Anyone help with this?
Thanks,
Nathan.

IPhone 4 voice/data connection issues?

I've had my iPhone 4 for around 6 months now. Lately I've been dropping a lot of out-going calls and have had some issues receiving calls in the last few days. Today I've had 3 voice mail notifications from people who have tried to call me and could not get through. It rings through to voicemail and sends me a notification after they're done recording. I have anywhere from 2 to 4 service bars, usually averaging at 3 in this location.
On top of the voice and call issues, I've been having problems with GPS and location services lately, too. I use the Waze app for directions. My phone will register 3G data signal, but none of the apps that use GPS can find any location. I have Location Service turned on in settings and have no problem starting my routes when I have wifi signal at home before I leave.
Phone details:
iPhone 4 8GB
Sprint Network
1 GB space available

Helo mchelman,
Thank you for using Apple Support Communities!
I was researching what you may be able to do in this situation, and want to recommend this troubleshooting assistant.
Calls and connection issues
http://www.apple.com/support/iphone/assistant/calls/
All the very best,
Sterling

Sql Server Connection Issues

After reinstalling Windows Server 2008 R2 EE my SQL 2008 R2 Sp2 Instances have some connection issues.
The server were installed under the same hostname, but he got a new sid in my active directory.
On the server there one DB Engine MSSQLSERVER, two named Reporting Services for MS crm 4.0 and SCOM and one Analysis Services Instance.
The DB Engine will collect Data from another DB, before writing to Analysis Services.
Here are the problems on the server:
When I connect via SSMS remotly, I sometimes get this error: Failed to connect to server <hostname> ... Named Pipes Provider, error 40 - Could not open a connection to SQL Server - Error 5
Both RS Instances have many event log errors like "Report Server (Instance) cannot connect to the report server database.". RS Reports are working fine, but sometimes the rendering is taking a long
time.
The DB Engine Agent Job to collect Data sometimes throw the following error: An OLE DB error has occurred. Error code: 0x80004005. An OLE DB record is available. Source: "Microsoft SQL Server Native Client 10.0" Hresult:
0x80004005 Description: "Unable to complete login process due to delay in opening server connection". End Error Error: 2013-12-10 06:03:40.41 Code: 0xC00291EC
User use Excel to connect to the Cube on my server. Often they got timeout errors. When they connect again it will work.
Are there any solutons on this?
Thanks a lot!

Hello,
The server were installed under the same hostname, but he got a new sid in my active directory.
Did you connect to SQL Server instance with Windows authentication? Since the SID of domain account is changed, the SQL Server instace may cannot verify the login account which stored in the master with old SID. In that case, please try to connect
SQL Server with SQL authentication and then readd the domian as login the instance.
Regards,
Fanny Liu
Fanny Liu
TechNet Community Support

WRT610N Connection issues

Similar Messages

Maybe you are looking for