WRT610N disconnects when transfering from wireless client to wired client

based on reviews, I purchased a WRT610N.
Have it setup with wireless N to work with my two laptops, and also have a desktop connected to one of the gig ports.
Whenever I try to transfer any files (or access the desktop) from any of the wireless clients, the wireless radio part of the router seem to reboot itself every 5 to 10 seconds.
If I go from a wireless client to another wireless client, it works fine. If I plug one of the laptops into one of the gig ports and transfer files to the desktop through the wired connection, it works fine. But as soon as either laptop try to access the desktop through the wireless connection, the radio goes into a reboot cycle until I stop trying to access the desktop.
Router has latest firmware. the two laptops has a Intel 5300 and intel 4965AGN card, both running windows 7, desktop is also running windows 7.
Used to be able to do this with a WRT150n without any issues, upgraded to the WRT610N for the gig port speed, but now this issue.
appreciate any assistance.

Ok I disabled IPV6 and now it will go about a minute of transferring files before the wireless dies.
AP Isolation is disabled.
Even tried from within the same room, direct line of sight from the laptop to the Router, about 5 to 7 feet away. Computer shows wireless signal at full strength.
I don't think it's the wireless cards in the laptops because I used the exact same setup with a WRT150N and WRT54GR and both work fine (although slower).
Just as a sanity check, I put the WRT150N back in last night and tested it, it would let me transfer files all night long without disconnecting.

Similar Messages

(AVC) Is there Any way to prioritize traffic from wireless client (laptop in my case) to AP

Is there any way to prioritize traffic from wireless client (laptop in my case) to AP …. if i explain the issue in a broad way there is no congestion going on in wired network. When multiple users connect to real presence and all share the same AP. they get real-time output over the call BUT if someone start file-transfer over the same AP the real presence call voice/video get stuck.
I applied the AVC feature on WLC but as i tested, i think prioritization from my laptop to AP will not happen and the situation remains same.
Please share if there is any way to prioritize traffic from wireless client (Laptop) to AP only ?

Hi Vinod,
Here is the AVC & QoS interaction for upstream & downstream traffic. For downstream it is important you have configured your WLAN with correct QoS profile & 802.1p values as that play a role even though you marking traffic using AVC.
Upstream1. Packet comes with or without inner DSCP from wireless side (wireless client).2. AP will add DSCP in the CAPWAP header that is configured on WLAN (QoS based config).3. WLC will remove CAPWAP header.4. AVC module on the controller will overwrite the DSCP to the configured marked value in the AVC profile and send it out.Downstream 1. Packet comes from switch with or without inner DSCP wired side value.2. AVC module will overwrite the inner DSCP value.3. Controller will compare WLAN QoS configuration (as per 802.1p value that is actually 802.11e) with inner DSCP value that NBAR had overwritten. WLC will choose the lesser value and put it into CAPWAP header for DSCP.4. WLC will send out the packet to AP with QoS WLAN setting on the outer CAPWAP and AVC inner DSCP setting.5. AP strips the CAPWAP header and sends the packet on air with AVC DSCP setting; if AVC was not applied to an application then that application will adopt the QoS setting of the WLAN.
I am not sure which controller software version you are running. From AVC perspective, it is good if you could install latest NBAR protocol pack (4.1 for WLC 7.5.x code or 6.3 for WLC 7.6.x code) on your controller.
Here is the 7.5.x AVC deployment guide which should help you on this
http://www.cisco.com/en/US/docs/wireless/controller/technotes/7.5/AVC_dg7point5.html
Like others mentioned, it is very little you can do with respect to upstream direction as AVC kicks in only when traffic hits WLC & not at the AP level.
HTH
Rasika
**** Pls rate all useful responses ****

I have inherited an ICloud account from one of my employers when transferring from old MacBook Pro to new MacMini and need to separate from this, presumably by setting up a new ICloud account. How do I do this ?

I have inherited an ICloud account from one of my employers when transferring from old MacBook Pro (which belonged to them) to new MacMini and need to separate from this, presumably by setting up a new ICloud account. How do I do this ? And is there any danger, in doing so, that I might delete any of her ICloud information ?

Sign out in System Preferences>iCloud. This will remove any synced data such as Calendars, emails and Contacts from your Mac, but will have no effect on the data on the server - so that other devices logged into it will continue to see the data.

Attribute support when transferring from Java to HTML in CF9

CF beginner.
When transferring from flash to HTML format, is there a way to control attributes which are not accessible through tags (for example HSCROLL and WIDTH in CFTREE)? Seems like going modifying the Ext JS object is the only way (for example using ColdFusion.Grid.getGridObject) as described in CFML reference but this apparently only works for editable objects. Is this the correct approach? Are there other ways of doing this? staying with a non-HTML format is not an option and so any help is greatly appreciated
Disclaimer: just starting with CF and haven't had a chance to try these things in practice.

As TD said... and you could upgrade to iPhoto 9 for $15 from the Mac App Store . Are your captions worth $15?
One thing to note: Upgrading your library from 2005 to the latest iPhoto won't necessarily be without issues either although iPhoto 9 has been out for awhile and most of the bugs should be worked out by now.

Wifi disconnects when waking from sleep mode; running Mountain Lion

Had this same issue with Lion as well,, wifi disconnects when waking from sleep mode,,,any ideas how to fix this pesky issue?

Hi Sky,
This has worked for a few...
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712
10.7…
System Preferences>Network, top of window>Locations>Edit Locations, little plus icon, give it a name.
10.5.x/10.6.x/10.7.x instructions...
System Preferences>Network, click on the little gear at the bottom next to the + & - icons, (unlock lock first if locked), choose Set Service Order.
The interface that connects to the Internet should be dragged to the top of the list.
Instead of joining your Network from the list, click the WiFi icon at the top, and click join other network. Fill in everything as needed.
For 10.5/10.6, System Preferences>Network, unlock the lock if need be, highlight the Interface you use to connect to Internet, click on the advanced button, click on the DNS tab, click on the little plus icon, then add these numbers...
208.67.222.222
208.67.220.220
Click OK.
Also, turn off IPv6:
System Preferences » Network » AirPort » TCP/IP tab » Configure IPv6
Or whatever Interface you use.

Cannot find picture when transferring from Aperture to PSE 11

Cannot find picture when transferring from Aperture to PSE 11
I have an older version of PSE and when I transferred a picture from Aperture to PSE9 it would open PSE9 and show the picture.
I set the Preps in Aperture for PSE 11 and the PSE 11 opens but no picture in the box or photo bin or in the top left "open".
I changed the Aperture setting to the PSE Organizer and the same thing happened Organizer open BUT there was no picture to be found.
In Aperture it shows the file being transferred.
I looked in the PSE 11 preps and file but could not find anything.
The fact that it opens the PSE 11 app tells me it is being recognized but the picture (file) is going somewhere else.
Thanks
Greg

Hi Greg
Make sure you are linking to the application in Support Files and not to an alias.

Outlook 2010 disconnects when switching from wired to wireless

A Windows 7 Pro 64bit laptop with Outlook 2010 keeps disconnecting from the exchange when switching from wired to wireless or vice versa. Then it wont reconnect. Restarting Outlook occasionaly works, not all the time.
Holding CTRL and clicking the Outlook symbol in the notifcation area they connection status and reconnect doesn't work either.
The only way it will reconnect apart from restarting the machine is to restart the Microsoft Exchange Information Store service on our Exchange server.
Any ideas?
Thanks,
JagJag363

Hi,
Since there is a period of time without any respond, I will
temporary mark the reply as answer to closed this thread.
And if you come back to find it doesn't work for you, please reply to us and unmark the answer, this thread will be re-opened.
Sincerely,
Max Meng
Sincerely,
Max Meng
Come back and mark the replies as answers if they help and unmark them if they provide no help.

When transferring from a 3GS to a Iphone 5, will my old text messages transfer?

I'm transferring from a 3GS to a new IPhone 5. Will my old text messages and emails transfer via the cloud or from my computer?
Thanks.

http://support.apple.com/kb/HT4946
"Messages (iMessage and carrier SMS or MMS pictures and videos)."
The messages should transfer, and the emails are attached to the email server so your inboxes will come back as well.

Access from wireless client

I want to access an application built up using XSQL Pages with a wireless client (Nokia). How do I configure my server to recognize the MIME type?

I don't know exactly why it has that delay, but I think it's because if first tries to connect on the wrong network card, then after that times out tries the other one.
what you could try to solve this is the following:
first create an empty unconnected Socket using Socket().
then Socket.bind() that socket with a SocketAddress that points specifically to the correct card.
then connect to the server using Socket.connect()
again, I'm not sure this will work, but it might.

HT4061 Why can't I access my music when away from wireless connection?

I have my music in iCloud but now I cannot access it when away from home what am I doing wrong.?

are you using itunes match?
if so go to settings> itunes & apps and at the bottom turn on use cellular data

Blurry photos in iPhoto 11 when transferring from iPhoto 6 on different computer

I recently bought a new MacBook Pro and I'm transferring my files over from my old MacBook. When I moved my photos from the old one (running iPhoto 6) over to the new one (running iPhoto 11), the images look horrible. They're all blurry and I can't enlarge them hardly at all without them looking really bad. Does anyone know why this would be and how I can fix it? Thank you in advance!

The key question here is what exactly did you move, and how?
This sounds very like you either copied only the thumbnails from the older machine or you imported one Library to another.
FWIW
To move an iPhoto Library to a new machine:
Link the two Macs together: there are several ways to do this: Wireless Network, <a href="http://support.apple.com/kb/HT1661"><b><u>Firewire Target Disk Mode</b></u></a>, Ethernet, or even just copy the Library to an external HD and then on to the new machine...
But however you do choose to link the two machines...
Simply copy the iPhoto Library from the Pictures Folder on the old Machine to the Pictures Folder on the new Machine.
Then launch iPhoto. That's it.
This moves photos, events, albums, books, keywords, slideshows and everything else.

Problem with track order (ID3 tags) when transfering from ZENcast Organizer = Vision:M 3

Hi there, I am using ZENcast Organizer V.2.00.4 and my Zen Vision:M's firmware version is V..6.0e
Okay, I have a time consuming problem with the way my podcasts are organized on my player. When i download my podcast from ZENcast Organizer everything is neatly organized. By that i mean that the tracks are positioned in the order in which they were released by the radioshow. Let me just give you a picture : [IMG]ttp://img530.imageshack.us/img530/4476/zencastbv4.jpg[/IMG]you can see that after the 27th comes the 28th and the 29th etc. That is also the way i would want the files to be played on my player, but unfortunately they are not.
Here is a pic of what the order looks like on my player after i have transfered some of the podcasts . Since there are no ID3 tags concerning track number, the player seems to sort the files alphabetically, which is a hassle for me as i have to search through my tracks each time I would like to listen to the following show.
The way that I have dealt with it until now is to download the tracks with ZENcast Organizer and then add the track number information with Media Monkey and then upload them to the player via Zencast Organizer. That is a lengthy and annoying process and since i have missed the show (due to my new work) for 4 month now, i have a lot of files that i must edit.
So I was just wondering if there is an easier method? I was thinking in the lines of a plugin for ZENcast Organizer that would add track number information? I wouldn't care if it numbers them 2 3 4 or 2 22 23 24 just as long as they come in the chronologically right order when i play them.

I did some testing and discovered that ZENcast Organizer indeed does know how to sort the files on my player so that they are played in the right order - under the transfer you just have to check the box which makes ZENcast Organizer convert the music (mp3) files into videofiles as shown in the picture: http://img50.imageshack.us/img50/439...ransferar5.jpg
This makes my player play them in the right order as shown here:
But i do not want player to be spending a huge amount of unnecessary power on showing a screen I am not going to be looking at.... my podcast is a radio show, there is nothing to LOOK at, literally.
Why on earth does ZENcast not change the filename when i choose to download the shows in their nati've mp3 form but only when I convert them to video?

Aperture 3 Issues when transferring from old Mac to new Mac

I just bought a new iMac 21.5 yesterday. I transferred all my apps and files from the old 17 inch from my Time Machine Backup.
I am running Ap 3.0.3 - RAW 3.0.2 - all software updates I can find are installed.
Have reinstalled 3.0.3 Aperture update
MOst things seem to have worked fine except Aperture.
Some images in some projects either don't display at all, some just have the white box, some are just black, some are full of odd noise (as if the raw version wasnt supported)...
All displayed perfectly before the move - the files are on my drive.
All are in JPG format.
Help please!

I had this same problem but now I think it is as "solved" as it can be. I tried rebuilding multiple times, and I even created a new library and imported my old one into it. After lengthy discussions with Apple support, it seems the problem is a conflict between Snow Leopard 10.6.3, Aperture 3, and the NVIDIA GeForce 7300 GT graphics card. The good news is that Apple is aware of the problem and is working on it, the bad news is that they haven't yet fixed it.
I followed the Apple tech's recommendation and it seemed to mostly fix the problem. He had me roll back from 10.6.3 to 10.6.2. You'll need to boot from your Snow Leopard install disc and re-install SL (no, this will not do anything to your files). Then, go to the Apple website and download the 10.6.2 combo update and install. (i.e., do not allow the computer to do an automatic software upgrade to 10.6.3 like it wants to).
What I get now is my Aperture 3 working much faster and with none of the strange artifacts I had before. The only exception is when I'm viewing a photo in full screen mode - for some shots I'm still getting the weirdness. However, this is still a huge improvement over what I had before - I can now actually use Aperture again
Good luck!

C# SCOM SDK agent install works fine from debug mode but disconnects when built from installer

My team is writing a C# application that installs SCOM agents on the fly. I used the code in :
http://msdn.microsoft.com/en-us/library/hh329037.aspx
as a template. Which works fine and will consistently install agents when I run it in debug from Visual Studio. But when I build an installer (using InstallShield), calls to:
"AgentTaskResult results = adminServer.InstallAgents(agents, configuration);"
always result in a Microsoft.EnterpriseManagement.Common.ServerDisconnectedException. The agent install even shows up in pending management on the SCOM server (but this sits in pending management forever and is never processed). Calling managementGroup.Reconnect();
and retrying the agent install still results in a ServerDisconnectedException. The application has no problem doing other things with the managementGroup object (from debug or running from an installer). It can create MonitorConfigurationOverrides and
gets events out of an outbound connector. So it seems like the disconnect problem is localized just to agent install requests.
I looked in the Windows Event Log and found an OpsMgr SDK Service Error:
An exception was thrown while processing InstallAgents for session ID uuid:71d39b19-f9a7-4d4a-82ee-5043480af635;id=41.
Exception message: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 778.
Full Exception: System.Xml.XmlException: '.', hexadecimal value 0x00, is an invalid character. Line 1, position 778.
at System.Xml.XmlTextReaderImpl.Throw(Exception e)
at System.Xml.XmlTextReaderImpl.ParseNumericCharRefInline(Int32 startPos, Boolean expand, StringBuilder internalSubsetBuilder, Int32& charCount, EntityType& entityType)
at System.Xml.XmlTextReaderImpl.ParseCharRefInline(Int32 startPos, Int32& charCount, EntityType& entityType)
at System.Xml.XmlTextReaderImpl.ParseText(Int32& startPos, Int32& endPos, Int32& outOrChars)
at System.Xml.XmlTextReaderImpl.ParseText()
at System.Xml.XmlTextReaderImpl.ParseElementContent()
at System.Xml.XmlReader.ReadString()
at System.Xml.XmlReader.ReadElementString(String name)
at Microsoft.EnterpriseManagement.RuntimeService.TaskRuntimeService.CreateRemoteJobXml(JobDefinition jobDefinition, ManagementPackTask task, Guid hsId)
at Microsoft.EnterpriseManagement.RuntimeService.TaskRuntimeService.SubmitJobs(IList`1 jobDefinitions, Guid batchId, JobCategory category)
at Microsoft.EnterpriseManagement.RuntimeService.TaskRuntimeService.SubmitTasksInternal(IList`1 jobDefinitions, Guid batchId, JobCategory category, PrepareResultSet prepareTaskResultCallback)
at Microsoft.EnterpriseManagement.ServiceDataLayer.AdministrationService.InstallAgents(Guid batchId, IList`1 jobDefinitions)

Hello,
You might ask in the
Visual C# Language forum on MSDN.
Otherwise, perhaps the Operations Manager - Extensibility forum:
http://social.technet.microsoft.com/Forums/systemcenter/en-US/home?forum=operationsmanagerextensibility
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

HT201317 issues seeing all photos when transfering from iphone5 to pc/mac

I'm having issues transferring photos from my iphone5 to pc/mac. I have over 200 photos on my phone however when I go to transfer only the last 20 or so photos are visible to transfer. why is this the case? it was working ok before now I cannot access all my photos from the computer. please help!

Whenever you plug in your iPhone to your Mac with iPhoto installed, iPhoto will automatically open up a screen giving you the option to download the photos in your iPhone...At least that's how it's set up in my computer. But I believe that's for photos taken by the iPhone.
Besides what said above, there is a iPhone Transfer Column which includes the tutorial about How to transfer photo/pictures from iPhone to Mac.
Hope it can do you a favor.
I may receive some form of compensation, financial or otherwise, from my recommendation or link.
<Edited by Host>

WRT610N disconnects when transfering from wireless client to wired client

Similar Messages

Maybe you are looking for