WRT610N firmware version

Hi,
SOme days from now, the WRT610N v1 firmware version is the same of WRT610N v2. Is that right or a problem on site content management?
Regards,

Upgraded on my v1 router using 2.00.00,05 firmware. Everything was fine but I have realized that the download speed from ISP provider become slower gradually (35Mbps -> 10Mbps -> 1Mbps). It tooks about one day. So I have to reboot the router to get the normal speed back. I have revert back to 1.00.03.B15 firmware.

Similar Messages

After WRT310N Firmware Version 2 update - Unidentified Network

Hi
I've owned the WRT310N for over 2 years now. I've been happy with it's features thus far. I updated the firmware previously to 1.0.9.
Recently, I upgraded my OS to Windows 7 from Vista. It's great and connects to my other hardwired network device (i.e. printer) and internet without any issues. I chanced upon a review that said the WRT310N Firmware Version 2 (WRT310Nv2_0_00_012.bin) was out and eagerly upgraded it in the router. Herein came the problem after the automatic reboot. My internet connection was unidentified with gibberish for an IP address. Strangely, my printer still connects and prints. But I can no longer access the set up page typically found in 192.168.1.1. There are no issues with my modem.
I tried many things with the assistance of the Linksys hotline in the Philippines (ref case:100408-000629). Simple 5 seconds, 30 seconds, 1 min resets, press and hold, unplug power, replug in power - Result = 0.
I tried to force ipconfig to dump the ip address, it could not release it or renew it. I tried to lower the duplex speed to 10MBPS, doesn't work. I thought the problem was the gibberish was on IPv6, by deselecting it, IPv4 wasn't able to correct itself.
Long story short, it was a fatal mistake to install Firmware Version 2 as after the reboot, I couldn't access the internet or the set up page that was necessary to reset the factory defaults. Without entering the router set up page, I can't help myself.
The kind Linksys lady told me I'm out of warranty and there's pretty much nothing I can do except by the brand new WRT610n with XXXXX features. I don't think I would as I'm very concerned about upgrading future firmwares in the light of this experience. So I'm putting this case up for your review. Hopefully, I'm the only "unique" case. =(
E

Push and hold untill lights go off usually I hold for 30 seconds. You should also turn off and unplug your modem while you do this. After doing that you should reboot your computer and then see if you can access the router, if you can but still dont have internet then you might have to release/renew the DHCP untill you get an IP. Can find that on the status tab.

WRT610N Firmware Release Notes

Hi All,
Where can I find the release notes for the new firmware version? It is not clearly stated in the linksys website (http://www.linksysbycisco.com/US/en/support/WRT610N/download).
Even though I selected my hardware version 1.0, I can only see on the release note the v2.0 as the initial release (which is obvious that is not true).
Regards,
AK

The release notes are confusing. This firmware is supposed to be working on both hardware v1 and v2, but firmware v2.0 is about the 4th published firmware for the WRT610N v1. Hopefully, they will correct it so that users don't think they have mistakenly downloaded the v2 firmware (even though in this case they are the same).

Problem with restore.I have a 2 gen running firmware version 4.2.1

Hello there !
Hopefully some smart persons here will be able to help me. First it has been awhile since i used my itune store because i didnt needed to and did a format of my computer after the last time i used it..so i had to upload my library etc and start from scratch. I downloaded a couple new games,everything was working fine..then when it came the time to sync and put these games on my ipod touch 2 gen the installation failed. I retried again and it keeps failing again and again so i choose to do a restore on it and expecting the problems would be solved. Problem wasnt not solved at all and it said an error (6) occured and i have the image on my ipod of the white cord trying to connect to itune store.
Restore doesnt work at all and it seems like my ipod is totally useless as i cant use it anymore. I did the diagnostic..it said no ipod were found. I also did the check up thing for the technician so ill paste it here maybe it will give some clues..
I have this error now as well... No iPod, iPhone, or iPad found. It also said secure link to itune store failed..not sure if these are all related to the same problems or all different at all..im clueless and need a generous soul to help me out.
Thank you tons for the help !
@Edit : Even with my other 2gen ipod i cant install these new games,it keeps failing as well..but at leasnt i havent done Restore on it yet and i fear to do it for reason you guys can guess.
Microsoft Windows 7 x64 Ultimate Edition Service Pack 1 (Build 7601)
System manufacturer System Product Name
iTunes 10.3.1.55
QuickTime 7.6.9
FairPlay 1.11.17
Apple Application Support 1.5.2
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 2.0.5.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 00AAB2F80F513CD0
Current user is an administrator.
The current local date and time is 2011-07-17 18:45:37.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce 9500 GT
**** External Plug-ins Information ****
No external plug-ins installed.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:     {B00FE55A-1662-4EE9-B880-6B076869B9F8}
Description:     Contrôleur Atheros L2 Fast Ethernet 10/100Base-T
IP Address:     192.168.2.10
Subnet Mask:     255.255.255.0
Default Gateway:     192.168.2.1
DHCP Enabled:     Yes
DHCP Server:     192.168.2.1
Lease Obtained:     Sun Jul 17 17:51:16 2011
Lease Expires:     Wed Jul 20 17:51:16 2011
DNS Servers:     192.168.2.1
Active Connection:     Connexion réseau
Connected:     Yes
Online:          Yes
Using Modem:     No
Using LAN:     Yes
Using Proxy:     No
SSL 3.0 Support:     Enabled
TLS 1.0 Support:     Enabled
Firewall Information
Windows Firewall is off.
ZoneAlarm Firewall is installed.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was unsuccessful.
The network connection timed out.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was successful.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-07-17 18:43:19.
**** Device Connectivity Tests ****
iPodService 10.3.1.55 (x64) is currently running.
iTunesHelper 10.3.1.55 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Contrôleur d'hôte ouvert PCI vers USB NEC. Device is working properly.
Contrôleur hôte PCI vers USB standard étendu. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C8. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27C9. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CA. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CB. Device is working properly.
Contrôleur hôte universel Intel(R) 82801G (ICH7 Family) USB - 27CC. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Devices Not Currently Connected:
iPod touch (2nd generation) running firmware version 4.2.1
Serial Number:     9E01226F201
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.

thats just rubbish ! i bought it secondhand for my daughter to use for music and apps, but its not compatible with anything, any suggestions other then throwing it away?

How do you upload firmware to Airport extreme with the following message: This version of AirPort Utility requires this AirPort Extreme use firmware version 7.3.1 or later. Use AirPort Utility 5.6 to update this base station. I'm using airport utility 6.0

The airport extreme at my parent's house has not had its firmware update in some time and it keeps dropping the internet connection and needing to be reset.
I went to update firmware and opened up airport utilities (I'm running airport 6.0 on Mountain Lion, 10.7.4). Everytime I open the airport utility I get the following message: "
This version of AirPort Utility requires this AirPort Extreme use firmware version 7.3.1 or later. Use AirPort Utility 5.6 to update this base station. AirPort Utility 5.6 is available at AirPort Service and Support.
I've followed the link and tried to update firmwares but none are available and the print says that airport utility will look to see if firmware are available and load them as necessary when prompted by user.
One link said the only way to solve this problem is open up Airport Utility 5.6. I tried to do this, but 5.6 is not supported on Mountain Lion and couldn't be opened up.
I'm getting the exact same message on my other computer, a Mac Air.
So basically, can't download new firmware and am stuck with a ****** airport extreme that needs to keep being reset, a factory reset, in order to use the internet, but then continues to give me the same message.
Thanks!

See this article for instructions on how to install AirPort Utility 5.6 for Lion on Mountain Lion:
http://www.macworld.com/article/1167965/mountain_lion_and_the_ancient_airport_ba se_station.html

Will firmware version 4.1.7 automatically update to 4.1.9?

I recently upgraded to OS 10.3 from OS 10.0 on my Imac 700MHz G3. The installation documentation said that I would be prompted to upgrade the firmware if I needed to. I was not prompted so I went ahead and did the OS 10.3 installation. The firmware remained version 4.1.7f4 after the install.
Not too long ago I went through the same procedure on my Imac 400MHz DV. The only difference is that I started the upgraded process from OS 9.I, then to 9.2.2 using the updates (ending at the latest version of 9), then to 10.0, and then to 10.3. And finally updating with 10.3.9 combo to OS 10.3.9. During that whole process I never new about firmware and never checked to see what version I had before starting this process. After all of the above installations were finished I ended up with firmware version 4.1.9f1.
My concern is with the 700MHz G3 IMac. I'd like to update to 10.3.9 using the combo update but I'm concerned about the firmware. Will firmware 4.1.7f4 be updated automatically to 4.1.9f1 after the combo OS 10.3.9 is installed? Or should I erase the disk again and start over by first installing firmware update 4.1.9? Actually if that were the case I wouldn't be able to update my firmware since I don't have the correct bootable version of OS 9 on disk that is required for that computer. However my previous experience with the installations on the 400MHz DV suggests to me that that the firmware will automatically be updated. But I would like confirmation from the experts. I'd hate to spend all that time downloading and installing all of the latest updates (Combo 10.3.9, etc.) only to find that the firmware version is incorrect.
Thanks!
Al

Al,
I don't understand your anger. In your first message
you posted that you installed OS 9 and updated it to
9.2.2. So why don't you do that again on the 700 MHz
iMac?
I find it very amusing that somehow you see anger in my post. That is realy very funny! The reason I didn't just simply install OS 9 on the 700MHz Imac is stated in my original post. I would need a special (the original disk that came with this computer) bootable OS 9.1 disk to install 9.1 on this particular computer. However if there are retail 9.2 or greater disks available then that would work to. I own a retail version of 9.1 that I used for the 400MHz Imac. That wont work on the 700MHz Imac. So now I have to buy a another OS 9 disk. Thanks for your input. Al

Firmware Version 4 1 106 1982 of IomegaEZ MAL PERFORMANCE and improve performance

Firmware Version 4.1.106.31982 of IomegaEZ MAL PERFORMANCE !!! and improve performance?
I upgraded to version 4.1.106.31982 the IomegaEZ and enter SETUP MAL has PERFORMANCE WEB, it is very slow unlike the previous firmware version; as performance improves VERSION of this? You can return to the previous version without losing data?
Thank You
Ruben Arno
ESPAÑOL
Version de Firmware 4.1.106.31982 de IomegaEZ de MAL RENDIMIENTO !!! como mejorar el rendimiento ?
He actualizado a la version 4.1.106.31982 el IomegaEZ y al ingresar al SETUP WEB tiene MAL RENDIMIENTO, es muy lento a diferencia de la version de firmware anterior; como se mejora el rendimiento de esta VERSION ? se puede volver a la version anterior sin perder datos ?
Gracias
Ruben Arno

Hello pcyservice
There is NOT a way to downgrade/roll-back/revert to a previous firmware without wiping all data. This is specifically mentioned on the firmware update page:
" CAUTION!
This update is not data destructive, however, ALWAYS back up your data before performing any firmware update!
Once you have updated the firmware, you will NOT be able to revert to an older firmware version."
I recommend you disable any unnecessary features/protocols such as Media Server and Active Folders, then reboot the unit.
If you are still experiencing performance issues, please contact LenovoEMC support to troubleshoot further.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/

HP OfficeJet Pro 8600 Plus Firmware version not current on the HP Downloads Page

My HP OfficeJet Pro 8600 Plus came with Firmware version CKP5CN1334ER which the printer update says is up-to-date. The HP downloads page shows CLP1CN1322CR as the current version. Can you tell me what the differences are in version 1334 from the one (1322) on the web page?
It would be nice to have the latest version posted for download to prevent confusion.

Same question here.

How do you determine the firmware version for a laptop docking station?

How do you determine the firmware version of a HP docking station?
Laptop Model: HP 2740p
OS: 64bit Windows 7
Expansion Base: 2740 Ultra Slim Expansion Base WA995AA#ABA
Thank you for any assistance.
Alvin

atenpo wrote:
How do you determine the firmware version of a HP docking station?
Laptop Model: HP 2740p
OS: 64bit Windows 7
Expansion Base: 2740 Ultra Slim Expansion Base WA995AA#ABA
Thank you for any assistance.
Alvin
WA995AA#ABA shows to be a hard drive, not a docking station

Did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version: 23.6

did the most recent update and now my TB Display turns off randomly on both my air and mini. I running TB Firmware Version:
23.6

When did you get this firmware version? My TBD is at 22.2 and the TBD bus is at 23.4. I thought I had the latest firmware.

How do I determine current firmware version for WRT54G

I've been poking around the site a bit, and note that there are mandatory upgrades to various firmware versions. I'd like to upgrade if necessary, but have no idea how to determine what firmware version I have right now.Message Edited by shelmart on 12-17-200605:36 AM

What is the excact hardware version # of your router? U can find that underneath the router itself, there's a sticker there & its just right below the Linksys Logo. If its version 5 or 6, u can go to this website: www.linksys.com/connect . Download & save Easylink Firmware Tool & then before u run that file after saving, disable first all your internet security like firewalls & anti- virus coz it will block the connection of this software from running properly. That EFL will automatically upgrade the firmware of your router.

Need a Script to Audit Firmware version of HP components.

Hi Team,
I am new to this portal, I am not sure if i have selected the correct board for this issue. If not please redirect thie thread to the correct team or guide me the link to the HP Blade system portal.
My issue:
We have 285 HP Servers, Where almost 275 are HP Proliant BL460 G7 & G8 Blades and the rest are HP DL380P and DL380 Standalone servers.
We recently did a HP SPP Update on all these machines and now for a reason we want to Audit if the component updates were correctly done by our engineers or not.
How ever for HP OS Components i have a script to Scan the registry and pull the Product version and match it to see if it has the Latest version or not.
But how do i do an Audit for the ILO'S of these machines and the Onboard Administrators and the HP Virtual connect if the firmware versions are correct or not ?
Is there any script or any Method to achieve this ?
We also have HP SIM tool as well, Can we do it form that? If yes then how ? Can any one please help in this ?

Frederik, After some tweaking and testing i was able to get it working, I haven't tested it via GPO as a startup script but standalone it is doing what i was after. I cant thank you enough for helping me on this as i had lost hope after days worth of intense
searching
Change that i had to apply ( space in a network path
was causing a "path not found error", Had to rename the "Office365 update" and update the path in Customconfig.xml or any other location that was pointing to "office365 update" )
set DeployServer=\\contoso\c2r\Office365 update\
REM Set ConfigFile to the configuration file to be used for
deployment (required)
set ConfigFile=\\contoso\c2r\Office365 update\Customconfig.xml
REM Set LogLocation to a central directory to collect script
log files (install log files are set in XML file).
set LogLocation=C:\AppData\Local\Temp

Nokia N80 new firmware version 4.0707.0.7

It's so bad firmware version!
I have lots of problems with new firmware version 4.0707.0.7 that I haven't with past version 4.0623.0.42 !
I can't understand what's going on with NOKIA Software Updater!
>I can't enter to my "Gallery\Images & Video" from "Camera Mode"
>My OS speed decrease
>Captured photos don't show in "Images & Video" until I restart my N80
>For each new files you add, you need to restart your N80 until your N80 find them in memory!!!
Why past version haven't these PROBLEMS and new version have them!!!
Does anybody know how can I return to my past firmware version (mean 4.0623.0.42) ? Is it possible?Message Edited by zoologist1 on 03-May-200712:28 PM

04-May-200710:53 PM
djassa1 wrote:
Basically it means that BB5 phones like N-Series including N80 and E-series cannot be downgraded to a previous version once they have been upgraded. Trying that with third party tools, because it's not possible through NSU, will brick (dead) your phone, period.
That's why I said you'd have to take the phone to a service center.

How to determine firmware version of brick?

Is it possible to determine the firmware version that the logic board has installed? I might be wrong about how the firmware operates, but the word 'firmware' to me usually implies flashing the BIOS. I know what version of 'firmware' the OS portion of the HDD has installed, but I'm not sure that it matches the BIOS and I'm still hoping I can revive the unit without repartitioning, etc. Background - I made the boneheaded mistake of trying to run sudo apt-get install -f <whatever> and was left with an SSH session where only bash built-ins would even run. No `ls`, no `cat`, no `sudo`. I tried to revive the system as best I could while the SSH session was still open using the errors reported and using this guide to abuse shell built-ins to recover a system in this state. But I ran out of time and had to close the connection (on a laptop). After this the system would power up but stay at white light LED indefinitely. So I popped the HDD into a spare linux machine and confirmed the drive looks fine - all data there and the OS RAID partitions were easily browsable. So I reimaged the OS RAID partition with rootfs.img from several different firmware versions (I really don't know whch one I was running as I've updated a few times but not sure when last), but still no luck. Am I wrong in assuming there's a BIOS update as well when we talk about 'firmware'? Am I missing some steps after reimaging the OS partition? Any help would be very appreciated.

I ended up soldering leads on the main board and captured the boot log. I managed to find only one other boot log to compare to (here) but comapring the two hasn't given me much insight. On the surface it seems like my issue is that the AHCI SATA loader is trying and failing to get port 0 to respond. I've posted the full boot log here, but I'll post the last bit here in hopes that someone can point me in the right direction. Thanks. Hit any key to stop autoboot: 0
init_sata:
serdes: 24Mhz ref clk
Serdes 1 : CMU OK
Serdes 1 : Lane OK
Serdes 2 : CMU OK
Serdes 2 : Lane OK
cap 0x6f26ff81 port_map 0x3 n_ports 2
P#SERR 0x4050002
IS 0x0
Port 0 control: 0x300
Port 0 status: 0x123
P#SERR 0x0
IS 0x1
Port 1 control: 0x300
Port 1 status: 0x0
GHC 0x80000000
GHC 0x80000002
ahci_init_one: SUCCESS
SATA Controller Info:
AHCI 0001.0300 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part
Enter start port: 0
Port 0 status: 123
cmd_slot = 0xb06000
Device not ready. BSY, DRQ or ERR in TFD!
Can not start port 0
timeout exit!
sataenv: GPT header not found
timeout exit!
sataenv: partition 7 not an environment
timeout exit!
sataenv: GPT header not found
timeout exit!
sataenv: partition 8 not an environment
timeout exit!
GPT header not found
Bad Magic Number
arg1 char: s
Barebox-C2K >/

Nokia 6500 Classic\Slide Firmware version 8.30

I've recently installed firmware version 8.30 on my Nokia 6500 Slide, can anyone tell me what the changes are in this recent firmware version?
Can't find anywhere what has changed in this firmware update, also not with Google.

I have noticed a couple of things:
1) When taking pics it looks like it has fixed the bug I had that I could not use the middle button sometimes when taking pics (was only intermittent)
2) It has a really annoying message when fully charged to say 'remove charger to save energy' which is very annoying!

WRT610N firmware version

Similar Messages

Maybe you are looking for