WRT610n v2 firmware. Please help.

Hello, i have a problem with my router. It's firmware seems to be corrupted, the power blinks all the time. I tried to flash a new firmware via TFTP but i can't find a firmware for the router It's not available on the linksys website anymore. Does anyone knows where i can get it? Please help.. Thanks

I've checked the Linksys website but no firmware available anymore. What happened before you had this issue ? Try using another outlet and check if the power will goes back to solid. Or you can try doing the following steps :
* Press and hold the reset button for 30 secs.
* While holding the reset button, unplug the power cord from the back of the router and wait for 30 secs.
* After 30 secs , plug in back the power cord and release the reset button.
* Wait for 1-2 mins and check if the power light goes back to solid.
Help, learn and share

Similar Messages

  • Linksys WRT610N V2 problem please help me

    i have Linksys WRT610N V2
    now i got problem the power light flashing still keep
    cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable why
    how to fix please help me
    now i using adsl modem direct connected i using linksys am300 adsl modem

    Your firmware is corrupt with a flashing power light.  Follow one of these two to restore your router.
    http://www.savemondo.com/2008/11/21/how-to-unbrick-a-linksys-router/
    or
    http://www.lancelhoff.com/how-to-fix-a-bricked-linksys-router/

  • WRT160N Severe Problem, Cant upgrade (downgrade) firmware PLEASE HELP!!!

    Had this router running for acouple weeks. Its had that **bleep** connection problem but just today it got even worse. About every 30 seconds it will lose connection to the modem and internet for about 2 seconds. So even if i try to upgrade my firmware down to 008 i dont get the chance. The upgrade gets about 50% done and then i lose internet and it fails. **bleep**?! please please please help
    Solved!
    Go to Solution.

    If you have downloaded the firmware already then disconnect your modem from the router, and just connect a computer straight to the router on any one of the LAN Port's...
    Follow these steps to upgrade the firmware on the device : -
    Open an Internet Explorer browser page on a computer hard wired to the router...
    In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
    Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
    Wait for few seconds until it shows that "Upgrade is successful"  After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
    Now reset your router :
    Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

  • WRT610N Nightmare, someone please help

    Hi I bought the wrt610N three months ago and now am just getting it set up. I am having tons of trouble and have already spent 6 hours with techinical support today. They are no help. I cannot log onto the router wirelessly unless I use the wireless connectivity utility provided with the router. I cannot connect to the router using the windows based connection utility. I have friends that frequently come to my house and they cannot log on the router. My wife's laptop cannot get on the internet through the router either. The only way it works is to have them install the software that came with the router. It is too late to return this (Best Buy only accepts returns after 30 days), anyone have a similar issue and have some ideas?
    (Mod Note: Edited due to non-compliance of forum guidelines.)
    Message Edited by kent07 on 03-28-2009 05:44 PM

    If you have Installed the Linksys LELA software on your computer, You can Uninstall that software from "Add Remove Programs" and remove that software from your computer. Once you uninstall it you will be able to connect to your wireless network using Windows Base utility. Here are some settings which you can change on your router. After this all your computer will be able to go online wirelessly..
    Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1
    Leave username blank & in password use admin in lower case...
    For Wireless Settings, please do the following : -
    Click on the Wireless tab
    -Here select manual configuration...Wireless Network mode should be mixed...This Settings are for 2.4Ghz
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
    - Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
    Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
    For Wireless Security : -
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WEP, Encryption should be 64 bits.Leave the passphrase blank, don't type in anything...Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
    Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
    Click on Advanced Wireless Settings
    Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
    Now see if you can locate your Wireless Network and attempt to connect...
    Wireless Network mode should be mixed...
    -Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network.
    Set the Radio Band to Wide-40MHz and change the Wide channel to159 and Standard Channel to 161-5.805GHz...
    For Wireless Security : -  This settings are for 5GHz Network.
    Click on the Sub tab under Wireless > Wireless Security...
    Change the Wireless security mode to WPA, For Encryption, select AES...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
    NOTE : Passphrase should be more that 8 characters...
    Now see if you can locate your Wireless Network and attempt to connect...

  • Computer Hangs for 30 Seconds at a time. Please Help!!

    My Macbook Pro has started locking up for 30 seconds at a time on fairly regular intervals (Every 2 - 10 min). When the lockup happens, it appears to affect anything that wants to use the hard drive. For instance, my browser will hang (i.e. do the beachball) but skype will work fine. During the hang, if I bring up any other application, it will hang if it tries to access the HD. I am not totally sure its the HD, but this is what I suspect as other background processes can continue during the lockup. It's important to note, that during these times, it is NOT using the CPU or the hard drive. It just sits there doing nothing. I do not hear the hard drive access going crazy. I also have 4GB of ram and it happens when almost nothing is open so it is not a performance problem.
    Here is what I have already tried
    - Disabling the SMS (sudden motion sensor)
    - Repairing the disk permissions
    - Verifying and repairing the disk
    - Using disk warrior boot disk to repair the disk
    - Downgrading from the 1.7 to the 1.6 EFI Firmware
    Please help. I'm out of ideas.
    Thanks,
    David

    I'm in the same boat, and I can't just replace my HDD..... I'm going to try and use my copy of TechTools plus to see if it spots the issue...
    Recently I have had that 5-10 second slowdown. I thought it was one of my externals because at the time of the slowdown, I'd hear teh external start to spin. It was a 1TB drive, and I passed it off as nothing because I thought thats what 1TB USB drive need to error check.
    Then, all of a sudden after taking my computer out of sleep mode (with no externals connected) my computer came to a standstill... I reinstalled OSx 10.6 and it was fine.
    Now I am noticing a 10 second halt at regular intervals as the OP mentioned. In my console it has this:
    12/31/10 4:53:28 PM kernel commaxtor_IOPowSec00_105-(B41VR3WH) handling stop request
    12/31/10 4:53:28 PM kernel commaxtor_IOPowSec00_105-(B41VR3WH) IssueModeSelectTimer: shortTime = 1
    12/31/10 4:53:28 PM kernel commaxtor_IOPowSec00_105-(B41VR3WH)::SetModeSelectTimer: using shortime
    12/31/10 4:53:28 PM kernel commaxtor_IOPowSec00_105-(B41VR3WH) IssueModeSelectTimer: complete
    12/31/10 4:53:28 PM kernel commaxtor_IOPowSec00_105-(B41VR3WH): IssueStopUnderDeviceControlCommand
    12/31/10 4:53:57 PM kernel disk0s2: I/O error.
    12/31/10 4:53:57 PM kernel
    12/31/10 4:53:57 PM kernel
    12/31/10 4:53:57 PM kernel hfs_clonefile: cluster_read failed - 5
    Looking at this, I am now assuming that the problem lies with my external maxtor drive...
    LUCKILY all of my info on my macbook is on another HD for time machine, so if my internal HD kicks the bucket, I'm safe. It's the maxtor one I'm worried about since it has my whole video production portfolio on it, lol.

  • WPS push button on the Linksys WRT610N router does not work. Please help.

    Hi,
    I am facing problems of the WPS Push Button on the Linksys WRT610N version 2.0 router which has stopped working. I don't see the Blue LED blinking. The WPS button no more works on the router. It was working before. I did a firmware upgrade. Could this be the cause?
    Please help me in solving this issue at the earliest.
    Leo.

    when you reset the router, did you notice that your network name changed?
    also check the settings on the router if the wps is enabled.
    with a computer wired to the router, are you able to go online?
    follow the instructions in this page to setup wps
    to connect another computer to the network, follow the instructions here

  • I am using an iphone 3g and when i connect my device to my laptop a dialog box appears saying that an update of 4.2 is available so went for it.after the firmware is downloaded via itunes it shows that the firmware is invalid!.please help.

    HEY GUYS I AM USING AN IPHONE  3g and when i connect my device to my laptop a dialog box appears saying that an update of 4.2 is available so went for it.after the firmware is downloaded via itunes it shows that the firmware is invalid!.please help.
    AND ALSO I HAVE HEARD THAT THE IPHONE 3G CANNOT BE UPDATED TO IOS 4.2!IS IT TRUE???
    PLEASE HELP ME.

    This means that the phone you have was software unlocked to use on any carrier, or hacked. When you installed the update it restored the lock that originaly came with your phone. Not much you can do now. Apple will not support hacked phones. You will need to find out the carrier your phone is locked to and see if they offer official unlocking, or start googling to see if you can find a way to unlock 4.2.

  • After EFI Firmware update 2.3, MBP Early 2011 will not boot. During restart it all went wrong please help!

    Hello,
    I've done an ample amount of Internet research to find an answer to this problem however nothing yet found is quite like this. I will start from the beginning.
    I am traveling through Europe, and I normally live in California. When I arrived in Ireland my MBP early 2011 15 inch, began crashing constantly when I had several tabs open on Chrome and maybe one or two low CPU/Memory using applications, nothing the 8gb RAM &750gb hard drive can't normally handle. Thus I began trouble shooting.  I ran disk utility once started up and repaired both disk and permissions. Still crashing. It didn't seem like it had anything to do with a kernel panic shut down, I never would receive the usual message indicating so. After that I did an SMC reset. It was still crashing. I then upgraded the OSX from 10.8 to 10.8.4 believing it could help. It did momentarily, but then crash again. (When it crashes screen goes black suddenly and upon pressing power button does a regular boot on my single partition). I decided attempting to repair using the Internet recovery option but it appeared my MBP had not yet have it installed, so I downloaded from Apple and began installing. Here I made a mistake, I unplugged the power source as it was restarting. When the gray screen and apple appeared, the loading bar shows up as it says it will when installing the update, but when the bar fully loads it crashes every time. I've tried starting in safe mode, which then loads but never goes further (I let it stand for two hours such as that and nothing). Then I decided to allow the MBP to fully charge overnight to give it time and charge. This morning the problem has stayed the same, even with power source plugged in. Please help I need this to work.
    Thank you and please ask any questions!

    Your constant crashing problem is probably some type of hardware fault which no update can fix. Doing the 10.8.4 update and then the firmware update just caused further problems. you need to take thr system to a apple store to be diagnosed and fixed if cost effective.

  • Mac pro running OS 10.5.8 won't boot. Apple logo and spinning wheel shows then Apple logo turns into Forbidden signage while spinning wheel continue. It happenened right after I installed a firmware. Had to restart.Please help. What can I do?

    Mac pro running OS 10.5.8 won't boot. Apple logo and spinning wheel shows then Apple logo turns into Forbidden signage while spinning wheel continue. It happenened right after I installed a firmware. Had to restart.Please help. What can I do?

    Work through the suggestions in this article:
    Mac OS X: Gray screen appears during startup

  • My iPhone 4S . the restore Ends at 60 % with error 1 (not -1). I reinstall iTunes, download iOS 7.0.3 as ipsw and No success :(   I Think that is a problem of the iTunes or firmware versions :/.   Apple Please Help us!

    my iPhone 4S the restore Ends at 60 % with error 1 (not -1).
    I reinstall iTunes, download iOS 7.0.1 as ipsw and No success
    I Think that is a problem of the iTunes or firmware versions :/.
    Apple Please Help us!

    You can't Restore to any iOS other than 7.1.
    If the error persists, try on another computer. Still no joy, it is a hardware failure.

  • I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks

    I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks

    vinayakfrommonroe wrote:
    I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks
    Hi: Check out the Apple article below.
    https://discussions.apple.com/message/15112985#15112985
    Stedman

  • Problem after installing firmware 1.4... please help!

    Hi all, i recently upgraded to firmware 1.4 (the recent available version)... and now, every few minutes the fan generates big noises (also generating heats around the speaker area)... i looked into the Activity Monitor and i found that there are some processes that are actually using up >50% CPU usage, but the strange thing is, i wasn't using these softwares at all...
    the reason why i said it is a problem with the firmware upgrade is that, this problem didn't happen to me before upgrading.. and beside this upgrade, i didn't install any other software thereafter...
    can some body please help me? is there anything i can do? or can i restore the firmware back to the previous version? thanks in advance.

    Thanks Sweet Polly. But the fireware restoration they talked about on that page is only for those who had problem DURING the fireware installation. "Note: This CD cannot be used to return an Intel-based Macintosh computer's firmware to a previous version if a successful update has already been performed.". i've got the fireware 1.4 successfully installed, and i want to restore it back to my previous version...

  • HT3024 after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

    after installing airport extreme card into g4 ibook 1.07ghz 512 ram it will only boot to open firmware, any ideas why? please help!

    Hi David,
    Have you done a PRAM reset, CMD+Option+p+r...
    http://support.apple.com/kb/HT1379
    In fact, do 3 in a row, takes a bit of time.
    Tried resetting the PMU for PB/iB?
    http://docs.info.apple.com/article.html?artnum=14449

  • Help with iPod 3G... firmware won't boot anymore... please help!

    I own an iPod 3G since August 2003.
    It always worked well...
    but a few days ago I went to turn it on (after not having turned it on for 3 weeks) and it booted, because the Apple logo appears, but it just won't go in!
    So I get the Apple logo all the time, until the battery's flat!
    After the battery got flat, I tried recharging, but all it does is run the Apple logo again (but I'm pretty sure it does recharge, even though the bar doesnt appear).
    I can still put the iPod on Diagnostic Mode... that still works, but not the actual iPod firmware.
    I've tried connecting it to the computer too, but nothing happens, Windows says that the USB device wasn't detected.
    Please help me!
    ps: i did an HDD Scan and after about 5 minutes it said HDD Pass (or something like that)
    i did a USB disk scan and it kept scanning and after 30 minutes nothing changed so I gave up (the ipod was really heating up)
    windows just recognizes that there's a device connected, but doesnt recognize the device
    What is wrong?

    Hi: Try this link,,,,,
    I can't get passed the Apple Logo

  • Tactic 3d Rage not turning on anymore after firmware update, PLEASE HELP

    I tried to update my firmware and did not read the instructions carefully, I never unplugged the headset when I updated the firmware of the usb transmitter. so after that my headset was flashing blue, and it was not working, I let it drain out. but now it wont open again, I read on some forum that I could plug the headset in another power source to get it to open again, so its plugged in my iPhone 5 plug right now and still not opening. please help

    Originally Posted by Yann31
    I tried to update my firmware and did not read the instructions carefully, I never unplugged the headset when I updated the firmware of the usb transmitter. so after that my headset was flashing blue, and it was not working, I let it drain out. but now it wont open again, I read on some forum that I could plug the headset in another power source to get it to open again, so its plugged in my iPhone 5 plug right now and still not opening. please help
    Hi Yann31,
    Just a possible solution I'd like to put out there..
    Maybe plugging the headset to the other power source for a longer period of time (15-30 min) might get it to work?
    Sometimes trying to charge drained headsets and turning it on immediately does not work.
    Or if you already did this, do you have another power source you can try troubleshooting with?
    Cheers!
    Philip-CL

Maybe you are looking for