WRTP54G Losing connection constantly

Background:
I have a WRTP54G Vonage router (firmware 1.00.62)
my ISP is current communications (a power line ISP)
I use the wireless connection with 2 laptops from work that use a VPN connection
I use the standard Vonage service on the phone port 1
Just yesterday, out of the blue, my vonage wireless router went haywire. Currently, I can get a wireless or wired connection. Then after about a minute, it loses the connection. Then, it'll "cycle" back and reconnect. Meanwhile, the phone part of the router is not provisioning (probably because of the sporadic connection).
What I do know: The connection at the ISP power modem is clean - if I connect to it directly, the connection is clean and constant. When I connect the WRTP54G, and connect my laptop to it (wired or wirelessly) the strange behavior happens. No settings were changed prior to this occuring and lastly, I completely unplugged everything last night and this morning it seemed to power up fine.
What I suspect, my wife tried to use her laptop to connect via VPN to work and somehow that triggered the problem. However, once the problem started, if I connect my laptop but not use VPN, the problem still occurs. I did see one posting and reply regarding VPN and port forwarding (not sure what that means) but puzzled as to why this problem would crop up now after almost a year of using the router in the same setup. Is the VPN causing all this problem and if so, is a power reset (> 1 minute) the best way to get the router back to "normal"? Other ideas on what's causing this and is the best course to replace or can this be fixed via settings or firmware? Thanks!

Got this from the Vonage site: http://www.vonage.com/help.php?category=88&nav=5
If this will not help, better check it with the Vonage support people.

Similar Messages

Wireless N WRT300, Constantly Losing Connection

This router Constantly loses the internet connection, and I am HARD WIRED to this router, is this not somthing they should have mastered Ages ago?
The wireless signal is Weak and constantly loses it's connection.
I've tried calling them to fix it, I've changed the MTU, from 1500, to 1400, to 1300 etc, etc, I 've also set it to auto.... nothing.
Every so often the internet connection Drops, the only way to fix it, is to Unplug the router and plug it back in. Soon as this is done the internet works instantly again. I can see the wireless being buggy, but NOT the hardwire, there is NO excuse for this.
And to boot I just love how bestbuy wont allow any exchanges on this type of hardware, And cannot return it, and I cannot exchange it for a different router. I can only echange it for the exact same make and model of router.
Message Edited by curtisbouvier on 11-16-200603:06 AM

I also have the wrt300N router. I am losing connection all the time either wirelessly or wired. When the router works it is blazing fast, but every 2-5 minutes it just HANGS which is REALLY ANNOYING!
I have updated the firmware. This happens on my wired XP machine, my wireless XP, or on my apple laptop. It is not the computers becuase my old wireless router (linksys i forget the number, but it was a b system at least 4-5 years old) did not have this issue....
I saw on some threads that port forwarding may help? Is this a solution? Anyone have any ideas? Clearly by reading the posts this is not an isolated problem....

Network Drives Losing Connection from Server 2012 to Windows 7 64bit Machines

I have about 20 users at my facility and recently upgraded our server from one running server 2003 to one running server 2012. Since that occurred, I have had numerous issues that I did not encounter on the old server.
Lately, users have been losing connection to the shared network drives randomly and constantly. The drives will come back on-line on their own but it could be 2 minutes or 30 minutes before they do and when users are in the middle of working on a document
from the network, they are unable to save until the drive comes back. Manually disconnecting and re-mapping them works sometimes but then the problem will re-occur. I have tried re-doing the shares and security settings and run a couple of supposed hotfixes
on the client side and the server side to no avail.
Now our regional office is suggesting that I re-connect the old server and then rebuild the new one with server 2008 r2, something I would like to avoid if possible.
I feel like this is a simple setting that I am missing, no conditions have changed except for the new server.
The server is a Intel Xeon CPU E5-2609 2.40GHz with Server 2012 64 bit on it. All computers (except on on 32 bit) are running Windows 7 Enterprise edition 64 bit.
Please help.

I made this change to the registry on the server and am waiting to see if I have any more drops.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\lanmanserver\parameters
Value:
autodisconnect
Data
type : REG_DWORD
Value:
ffff (Hex)
There was a client side change suggested but I am missing that value for the client side change and others in the organization who don't have it are not experiencing this problem.

Why does my iPad2 suddenly keep losing connection on facetime?

Why does my iPad2 suddenly keep losing connection on FaceTime and tries to constantly reconnect?

Does it happen anywhere that you use FaceTime or only in your home WiFi network? If it happens with your home network, have you tried power cycling your router? Unplug it for about 30 seconds and then plug it back in.
Turn WiFi off and on in the settings. Reset the network settings.
Have you tried any troubleshooting steps at all?

Simple "fix" to Mouse losing connection.

I was constantly losing connection between Mac Mini and my Mouse. Also battery drain was an issue. I left the battery cover off a few months ago off and have had no problems with connection since and still using same batteries (I used to have to change them weekly or biweekly).

Hello:
Try resetting the PRAM and SMC. It is also possible that the mouse is failing.
Barry

Apple TV losing connection with iTunes on Windows

I am running iTunes on both an HP MediaSmart Windows Home Server (WHS) and a newly installed Windows Vista system. I have multiple Apple TV's around the house - both ATV2's and ATV3's.
I was using the MediaSmart Server as my main iTunes server for Apple TV streaming. That was the system's only function. Unfortunately, I was constantly restarting iTunes and/or the system as my Apple TV's would lose connection to home sharing. I thought WHS was the problem so I set up an unused computer to install Windows Vista (only license I had laying around) and installed iTunes. Everything seemed to work fine for a few days then I started losing connection to that iTunes also. I turned off the WHS system thinking it was causing the other iTunes to choke. That did not help.
For reference, All of my computers are hard wired and I have some ATV's that are hard wired and some that are using wireless. Wired or wireless....the problem still exists. Also, I have competely disabled anti-virus and the firewall on both iTunes servers.
I can watch multiple movies at one sitting. However, if iTunes is idle overnight (or even for a few hours it seems), my Apple TV's can not re-connect to home sharing and I need to restart iTunes.
Last night I disabled the AppleMobileDeviceHelper and the iPodService services hoping that would help. I have not had a chance to fully test this out yet, but did stumble across quite a few posts where MANY others are having tjhis same issue. Many are saying it has to do with the ATV3's sleep mode. If I recall correctly, my major problems did seem to start about the time I got my first ATV3. When I get home tonight I will disable the sleep mode on all of my ATV's.
Here is the question...just in case that works: Is powering off the device by holding down the play button the same as allowing the device to "sleep"? I ask because I use Harmony remotes and I have programmed them to power off the Apple TV when turning off all devices.
As I said, I have multiple ATV's (7 to be exact - 3 ATV3's and 4 ATV2's) and would hate to leave them all on all the time just to fix this problem.
Any feedback would be appreciated. It is difficult to discern a solid solution from the 400,000 other posts on this topic.
Thanks.

Sorry, I updated another thread I was a part of but didn't update my own thread.....ughhh!
I updated all of my ATV 2's and 3's to the latest firmware when it was released and have been problem free since. I do believe the major issue of not being able to connect after a period of inactivity has been corrected with the latest ATV firmware.
I can look at my network connection table using "netstat -an" in a CMD window and I do not see the massive number of connections I saw before the update.
Here is a link to the other thread I was referring to above:
https://discussions.apple.com/message/19952545#19952545
Have you applied the latest firmware updates to your ATV 3's?

Windows 8 keeps losing connectivity

Hi, not sure if this is unique but for the past few weeks Windows 8 has been losing connectivity every few minutes when browsing web pages, playing games etc. I am sure it's windows 8 as I have another work laptop using XP that I can be on all day via a
VPN and that does not drop at all (it would normally drop within a few seconds of losing connectivity). I've done a lot of searching on the net for the same issue, others seem to be having similar things happen such as slow speed but can't find anything that
matches, hence this separate question.
I have also tried swapping routers to no avail. The thing is, you wouldn't know anything had happened from the network connectivity. Suddenly a page won't load. The wireless connectivity at the bottom right of the screen shows a full 5 bars (not limited
connectivity). The way to get it back again is to leave it for a few minutes or disconnect from the router and reconnect again. Even whilst typing this I have had to do that twice.
I'd appreciate some suggestions!
Many Thanks, Paul.
PS... IPCONFIG/ALL shows...
Microsoft Windows [Version 6.2.9200]
(c) 2012 Microsoft Corporation. All rights reserved.
Wireless LAN adapter Local Area Connection* 17:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft Hosted Network Virtual Adapter
#3
   Physical Address. . . . . . . . . : 56-DE-2B-64-0B-25
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter WiFi 2:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Qualcomm Atheros AR5B125 Wireless Network
Adapter
   Physical Address. . . . . . . . . : 74-DE-2B-64-0B-25
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.0.4(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : 11 May 2013 10:31:15
   Lease Expires . . . . . . . . . . : 12 May 2013 10:31:21
   Default Gateway . . . . . . . . . : 192.168.0.1
   DHCP Server . . . . . . . . . . . : 192.168.0.1
   DNS Servers . . . . . . . . . . . : 194.168.4.100
                                       194.168.8.100
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Local Area Connection:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetLink (TM) Ethernet
   Physical Address. . . . . . . . . : DC-0E-A1-07-A8-F0
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{A319BEA5-A55C-4E0C-AF67-922BEBD4C7BB}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 13:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   IPv6 Address. . . . . . . . . . . : 2001:0:9d38:953c:3483:1732:adda:66e3(Pref
erred)
   Link-local IPv6 Address . . . . . : fe80::3483:1732:adda:66e3%14(Preferred)
   Default Gateway . . . . . . . . . : ::
   DHCPv6 IAID . . . . . . . . . . . : 436207616
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-16-28-39-CC-DC-0E-A1-07-A8-F0
   NetBIOS over Tcpip. . . . . . . . : Disabled

Hi,
Does this issue occur with both wireless and wired?
I suggest to perform these tests to troubleshoot the issue:
1 Update NIC card for your machine
2 Temporary disable firewall and antivirus program
3 Logon with Safe Mode with Networking
4 Update framework for your router.
Leo Huang
TechNet Community Support

Been losing connection for magic mouse and wireless keyboard

When I have my MBP running Mavericks in clamshell mode, I lose connections to both magic mouse and apple wireless keyboard in clamshell mode. I've tried all the PRAM SCM, aluminum foil and paper tricks. What I then did was test what happens when I leave the MBP open rather than in clamshell mode and it appears to avoid losing connection, at least that is what I've concluded with Mavericks for now..... anyone else able to replicate this? Having to leave the MBP open is not ideal.

Barry, thanks, still not working. I've tried every thing I can think of or have read, what I'm concluding is that there is either a problem with Mavericks or something has changed on how bluetooth works in Mavericks. Did not have this problem for the last 4 years. I can reproduce the problem when I close the laptop. I had the Bluetooth and wireless card checked out and replaced about 3 weeks ago. Problem has continued.

External drive conntected to Time Capsule keeps losing connection

I've been having this problem since I bought my TC over one year ago. Other than this everything works fine (aside from the occasional need for a restart).
I have an external 500GB drive attached to my 500GB TC via usb. I use the TC strictly for backups and the other drive to host my media files. When I want to use those files I switch on the drive. Only about half of the time does that work. When it does work everything is fine. I see the drive in the finder as expected.
When it doesn't work, I can see the drive name in the finder. But if I click to go into the folder, I get an error saying that the connection cannot be found.
It shows up in the Airport Utility as normal.
Powering the drive off and on does not help.
Relaunching the finder doesn't help either.
The only way I can connect to the drive again is to either logoff and log back into my mac, or restart the TC.
It seems that my computer is remembering some kind of network disk mounting settings that don't get refreshed when I turn on the drive, but then do get refreshed when I logoff and back in. Does anyone know how I could force that refresh to happen? Has anyone had this problem before?
Any suggestions would be much appreciated
PS all my software and firmware are the latest.
Thanks.

OS X fan
This helped meRe: Time Capsule keeps losing connection in Finder
Dec 17, 2013 4:08 AM (in response to whootang12)
Left click on the Finder icon from the Dock and click "Connect to server...", go to recent server and click on your Airport Time Capsule.
THANK YOU!!!!
This solved it for me!

LaCie external hard drive keeps losing connection to Windows 8.1 computer

Hello all,
My LaCie external hard drive (Rugged version) seems like it keeps losing connection to my brand new Windows 8.1 laptop. The laptop is an HP Pavillion 15-p 133cl TouchSmart Notebook which I just got today. Basically, every few minutes, or if I nudge the external
a bit, the computer will seem like it disconnected and reconnected to the external hard drive in a split second and bring it up in the Windows Explorer. This external hard drive doesn't show any problems connecting to any other computer, but it has occurred
with 2/3 ports on this computer so far. I'm a bit worried, because I definitely DO NOT want the files on this external to get corrupted in any way. What should I do? Thanks a bunch.

may I know your external HDD model, to check which USB version to isolate power and cable connection issue
if this is USB 3.0 try to attached at USB 3.0 at your laptop, your laptop has 2 USB 3.0 and 1 for 2.0, for external HDD with USB 2.0 sometimes need more power / more than 1 connection, sometimes the power will loose
but since the trigger it will disconnect if you nudge the HDD, I suggest back up data to your laptop first, try to change with other data or power cable, try also update your laptop chipset
try to check with other device to isolate port issue
may I know if you are using other PC, did your external HDD also will disconnect if you nudge it?
contact your external HDD manufactured to get some suggestion

Questions About Losing Connection

Like other people I've noticed here, my WRTG45 v5 wireless router has recently started losing connection to the net multiple times a day. At first, we thought it was because our modem was old, so we bought a new one, but it didn't fix anything. So here are my questions:
1. My dad seems to think that a configuration or setup CD (that we lost) is required to make the router work with the new modem. Is this true? I don't think so, but I have to ask just so I can get him to move on.
2. I noticed in other posts here that programs like Bittorrent can cause the router to be overworked or whatever. This might explain our problem, as I use Bittorrent a lot (but not everytime the connection has dropped). If this is indeed the problem (or contributing to it), is there anyway to deal with it while still being able to use the program?
For the first couple months, the router was working fine. Even with Bittorrent running a lot, and all the computers (2 wired, 1 wireless, and 1 wired X-Box) engaging in various activities on the net. So this is very puzzling to me.
One more bit of information, I have given every computer a unique, static IP address. However, I noticed recently that when I look at the router configution after typing in its IP address in a web browser, that it is set to DHCP Enabled.
Also, in the advanced TCP/IP settings for this connection, under the WNS tab, the NetBIOS setting is set to the default of using NetBIOS from the DCHP server.
Since I am using static IP addresses, could these DHCP centered settings be causing problems? Although, even if they are, it still doesn't explain why the router was working fine months ago (unless someone changed stuff without my knowing).
Anyway, any help at all would be appreciated.

I assume you meant that you had a WRT54G v5 router.
First of all, the setup CD is not required. All router settings can be made by going to the router's web pages at 192.168.1.1
It is possible that the static LAN IP addresses are causing your problem, if they were not set up correctly. Linksys has a strict set of rules to follow regarding static LAN IP addresses.
With Linksys routers, a fixed (static) LAN IP addresses must be assigned in the device that is using the address. So you need to enter the fixed address in the computer or printer, not in the router.
When using a Linksys router, any fixed LAN IP address must be outside the DHCP server range (typically 192.168.1.100 thru 192.168.1.149), and it cannot end in 0, 1, or 255.
Therefore any fixed LAN IP address would normally need to be in the range of
192.168.1.2      thru 192.168.1.99 or
192.168.1.150 thru 192.168.1.254
assuming you are still using the default DHCP server range.
Also, in the computer, when you set up a static LAN IP address, you would need to set the "Subnet mask" to 255.255.255.0 and the "Default Gateway" to 192.168.1.1
It is also important that no two devices on your network be set to the same static LAN IP address.
Check all of your static LAN IP addresses. If you have violated any of the above rules for static LAN IP addresses, it could be the cause for your problem, and you should fix it before attempting any other router repairs or changes.
You should leave the DHCP server turned on. This way, if you have a visiting friend who you want to connect to your system, it will be easy to do.   Leaving the DHCP server turned on should not cause any problems, even if all your addresses are fixed. In general, you should let the DHCP server assign all addresses, unless there is a specific reason to use a static address. You can mix static and DHCP assigned addresses on the same LAN, as long as you follow the above rules for static addresses.
Linksys routers have had problems when BitTorrent is used. Your router has new firmware posted that should improve compatibility with BitTorrent. It is firmware version 1.02.0   You will need to download and install this firmware (after fixing the static address problem, if any). (Note: When you update your firmware, you should use a computer that is wired to the router. Also, when you do a firmware upgrade, turn off all other computers on your system, and unplug all other wires from the router.) After you have installed the firmware, and powercycled the router, you will need to reset your router to factory defaults, then setup the router again from scratch.
Message Edited by toomanydonuts on 04-12-200712:54 AM

Why does my mouse keep losing connection every minute

why does my mouse keep losing connection every minute, its not the batteries

I'm having the same issue. Every so often it loses connection then re establishes. This goes on repeatedly.
If you change batteries while the computer is still active then it takes for ever to re connect.
Can't wait until someone replies to your question.

Why does my iPad keep losing connectivity

Why does my iPad
keep losing connectivity ?

Hi Joan,
I'm sorry to hear you are having issues connecting with Wi-Fi from your iPad.
The article below may be able to help you with this issue.
Click on the link below to see more details and screenshots.
I've quoted some helpful highlights for you:
iOS: Troubleshooting Wi-Fi networks and connections
Be sure that you are in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and then on again.If unable to do so, see this article.
Confirm that your Wi-Fi router and Cable or DSL modem are connected to power, turned on, and indicate that they are connected to the Internet.If not, refer to your network administrator or ISP for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you are connected. Then tap the blue dot and choose Forget this Network. Try to connect to your desired Wi-Fi network again.
Note: You will need to enter your Wi-Fi password again if your desired network requires one.
Turn your Wi-Fi router off and then on again2. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware2.For AirPort Base Stations, see this article for information about firmware updates.
If your issue is still unresolved
Follow the steps below for the issue you are experiencing.
Unable to locate a Wi-Fi network
Unable to connect to a Wi-Fi network
Wi-Fi disconnects, or signal strength is less than expected
Unable to access the Internet while connected to Wi-Fi
Unable to automatically connect to Wi-Fi
I hope this information helps ....
Have a great day!
- Judy

HT2845 why does my wireless mouse keep losing connection?

Good morning,
My wireless mouse keeps losing connection...my batteries are at 100% and the "discoverable" option is checked off. Why is this happening?

Hi:
PRAM=parameter random access memory - reset like this:
http://support.apple.com/kb/PH11243
SMC=system management controller reset like this:
http://support.apple.com/kb/HT3964
Sometimes resetting these "fixes" odd problems - and it cannot hurt.
To make a device a favorite, go to system preferences>bluetooth. Highlight the device. If detailed information is not shown, click oin the little gear>show more info. Then click on the gear again and make the device a favorite.
Barry

Mouse losing connection

My mouse is losing connection with my computer on a regular basis, and regaining it after around 1-2 minutes. The problem is happening every day, sometimes up to 5 times, during which time the mouse is completely unresponsive. I've tried rebooting, turning the mouse on and off, changing the batteries but nothing seems to work. Can anyone help, as I've never had this problem with wireless mice before?

Hello:
Try resetting the PRAM and SMC. It is also possible that the mouse is failing.
Barry

WRTP54G Losing connection constantly

Similar Messages

Maybe you are looking for