WRTU54G-TM/firmware v1.00.15 internet dies

Set up just fine, worked for ~30 hours, then the internet hung, hard.  LAN still worked, web interface still up, but no pings, no traceroute, no nothing from the WAN side.  Required a cold reboot.  Working again now, but this is unacceptable, even once.
RMA time.  Is there email tech support, or do I have to sit on hold and get a case ID to get my  $20 back?

To fix wired connection you may reduce the MTU Size to 1300 under the setup tab...
For Wireless Connection try this - 
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Wireless channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WEP, Encryption should be 64 bit.Leave the passphrase blank, don't type in anything...
Under WEP Key 1 type in any 10 numbers please(numbers only and no letters eg: your 10 digit phone number) and click on save settings...
Please make a note of WEP Key 1 as this is the Security Key for the Wireless Network...
Click on Advanced Wireless Settings
Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304, Change the RTS Threshold to 2304 >>Click on "Save Settings"...
Now see if you can locate your Wireless Network and attempt to connect...

Similar Messages

  • WRT54GC: Internet dies when accessing a webpage with alot of pictures

    Hi all, recently I noticed that when I'm browsing to a webpage with alot of pictures my internet dies on the PC I'm accessing it on. I disabled all software-firewalls and it keeps doing it. I'm surfing wired. Tested it with both IE and FF. The other PC's that hang on the net don't disonnect so the router keeps its connection. I have looked through all the options on the GUI but can't find anything. Does anyone have an idea? Or if you need more info, ask and I'll try to provide so this problem can be solved! Thanks in advance

    Hi… logon to router’s setup page and reduce MTU to 1458 check whether it makes any difference, if it still doesn’t work try upgrading latest firmware on the router, after upgrading latest firmware on the router, reset the router and reconfigure it according to ISP settings and reduce MTU to 1458…

  • After updating my MBP to firmware 1.1 my internet does not work anymore

    Please help,
    A couple of days ago my MBP asked me if I wanted to update to Firmware 1.1 and I did. I followed the steps like it said and when I restarted it my internet was not working anymore. I called my internet provider and they tried helping me but no luck.They gave me the codes and I tried to set up the PPP address and other codes.
    I am using a DSL cable and a Ethernet connection.
    Does anyone know how I could solve this?
    Thanks!

    Try resetting your iPad:
    Double click the Home button. Slide up with one finger on ALL your apps to close them.
    Then, Press the Sleep/Wake button + Home button and hold 15 seconds or until you see the Apple logo.
    This will reset your device without erasing data, apps or settings.

  • I download the new firmware and now my Internet says its working buy it won't let me do anything?

    I download the new firmware and after I download it my Internet will say it is connected but then when I open safari or anything that involves Internet it will say it is not connected?

    I download the new firmware and after I download it my Internet will say it is connected but then when I open safari or anything that involves Internet it will say it is not connected?

  • Internet dies in 10.8.2

    I am running a mac Pro desktop made in Feb. of 2008, 2 x 3 GHz Quad-core, 8GB DIMM. Working well on 10.6.8. Tried to update to 10.8.2 with download from App store and it works as long as I don't open either mail or web-browser. With either of those, they work for about 5 minutes, then stop. Gradually everything else slows down until it takes quite a long time simply to open a window. When I open Network in System Preferences, it tells me I am connected. When I run the diagnostics, it get the same. The report is that I am connected to the internet, but I still can't get either mail or web to work. Tried several different browsers with same result. Any suggestions? Thanks in advance.

    The sites change, but recently I was sent to
    http://www.healthywaytocook.com/?utm_source=bluelink&utm_medium=cpc&utm_term=137 9182_747935&utm_campaign=noniewhitelist&k=arizona+idvorce
    Or I will often be sent to a site to watch video.
    The pevious site came after clicking on a link at NBC News.

  • Install firmware update without simultaneous internet connection

    I use a USB modem for internet service.  Airport Utility want both air port connectivity and internet connectivity.  I therefore can't install the update.  Is there a way around this ?

    Unfortunately the only way is to be connected to the internet. If you are near an  store you can take it in, I'm sure they will be happy to update it for you.

  • E71 firmware update via infrared, internet or blue...

    It is IMPOSSIBLE connecting my E71-2 via USB to windows. 
    I need to upgrade the firmware, is there a way of doing it without USB?

    Hi,
    I didn't have any problems with the phone. It's just when I originally got the phone about a year ago I was enthusiatic about updating the firmware as this had solved many problems on my previous N73 but I couldn't find an update. I had thought that a pre-emptive strike was in order before I started to use the phone.
    Having become used to the E71, I really like it, I thought I'd check to see if a software update was available as it hadn't been when I first had the phone.
    The only problems I've had weren't really phone specific e.g. the positioning server for the assisted-gps needed changing and I had to buy Adobe Reader LE 2.5 to be able to usefully read documents i.e. word re-flow and large file sizes and was so greatful that Opera released mini beta 5 - excellent.
    When I upgrade firmware on a PC you always get a chance to backup the original just in case things don't work out so you can get back to a working state. This doesn't seem to apply in the World of mobile phones. When you update firmware on a PC it doesn't stop programmes from working.
    During the update process you are asked to ensure that your memory card is not encrypted or locked. Not very clear. It would be much better if you were warned to un-install security programmes, then backup, then update, then restore, then re-install security programmes. It would be truely wonderful if you could backup or download the original firmware just in case or make an image of the phones present state so that this could be replaced intact if necessary.
    Does anything like that exist for the S60 platform?
    Thank you.

  • HT1237 Searching for an EFI Firmware update to enable Lion Internet Recovery on MacBook Pro (15-inch, Mid 2010)

    Hi All,
    My Mid-2010 Apple MacBook Pro 15-inch started having random kernel panics lately (more than 1 month of random kernel panics now), usually associated with request such as "open new tab in Safari" etc.
    Since I installed 2x4GB RAM modules from Crucial when I bought my MBP (they are +- 2 years old now) and also exchanged my DVD-drive for an extra SSD that now runs the system (fully updated 10.7.4) I have a feeling that those kernel panics might be HW related.
    I wanted to run Apple Hardware Test but found out that it is no longer supported on Lion. Since I don't have any optical drive to install AHT from (also I don't have the CDs with me atm), I found out that I can install an EFI Firmware update that enables internet-based (?) AHT.
    At http://support.apple.com/kb/HT4904# , the link from MacBook Pro (15-inch, Mid 2010) links to MacBook Pro EFI Firmware Update 2.6 which is for Early 2010 models only and doesn't allow me to run the installation process. I'm looking for an EFI update to enable Apple Hardware Test on my Mid-2010 Apple MacBook Pro 15-inch.
    Is there an update that can do this? Is there a wrong hyperlink on Apple page or am I searching for a wrong update?
    Also, even though this should probably be in a separate topic, can anyone please point me to the right direction for a good Apple Kernel Panic how-to-read-those topic?
    Thank you very much in advance.

    Hey Cris from London,
    I would try out the recommended steps in the following link:
    OS X Mavericks: If your Mac runs slowly
    http://support.apple.com/kb/PH13895
    Let us know if any of the steps within resolved the issue.
    Welcome to Apple Support Communities!
    Take care,
    Delgadoh

  • E2000 - No internet after upgrading firmware

    Upgraded my firmware on my E2000, Internet no longer works, and @officiallinksys wants $30 to fix their lousy product. Can you say scam?

    I believe after the product will be out of warranty they do offer programs that would let you extend the service of your router. Regarding your concern, you may need to reset your router and reconfigure it's settings. A reset is a must after every after upgrade. Push and hold the reset button using a pin or paper clip for 30seconds then power it off for another 10-15 seconds. Once the power light goes solid, you may start the reconfiguration. For further info on how to reconfigure the settings, you may refer to these links: Setting up a Linksys router with Cable Internet service and Setting up a Linksys router for DSL Internet connection.

  • WRT54G; What is latest version of firmware ?

    I have a WRT54G v4 and somehow I had noticed I upgraded to 4.30.5.  When I went to web to see if I still ahd latest it said 4.21.1 was latest.  So, I quickly re-flashed with 4.21.1.  I went into the 4.30.5 release notes (below) and it DOES say WRT54G.  What's up ?
    Linksys, A division of Cisco Systems, Inc.
    Product:                WRT54G
    Classification:         Firmware Release History
    Firmware  Date:  04/27/2006
    Release Date:           05/25/2006
    Last Firmware Version: 4.30.5
    Firmware 4.30.5
    - Resolves UPnP vulnerability reported by SANE
    Firmware 4.30.2
    - Resolves issue with filter name
    - Resolves issue where service name for PPPoE cannot be added
    - Resolves issue with detecting UHP modems
    - Resolves issue where DynDNS Custom and Static accounts cannot be used
    - Resolves issue with WEP passphrase not recognizing spaces
    Firmware 4.20.7
    - Resolved issue with SecureEasySetup button delay
    - Resolved issue with SecureEasySetup overwritting current wireless settings
    - Resolved issue with not being able to disable SecureEasySetup button
    - Resolved issue with Diag light being constantly lit after upgrading to 4.20.6 on v.1 hardware
    - Resolved issue with iDefense security vulnerability
    - Resolved issue with L2TP disconnect
    - Resolved issue with SecureEastsetup long button push not resetting wireless settings
    Firmware 4.20.6
    - Resolve issues with setup wizard
    - Updated wireless security menu
    - Resolve issues with port based QoS
    Firmware 4.00.7
    - Adds SecureEasySetup push button support
    - Resolves large file transfer issues
    - Resolves issue with enabling TKIP after enabling WEP
    - Updated QoS features
    - Resolves issues with multiple Access Restrictions policies
    - Resolves issue where multicast breaks when MAC filter status changes
    Firmware 3.03.6
    - Supports hardware version 3
    - Updated help file
    Firmware 3.03.1
    - Wi-Fi certified
    Firmware 3.01.3
    - Updated wireless driver
    - Supports hardware version 2.2 (cannot downgrade to previous versions)
    - Resolves issue with VoIP adapters
    - Resolves issue with long domain names
    Firmware 2.04.4
    - Updated wireless driver
    - Updated certificate generation for https access
    Firmware 2.04.3
    - Resolves issue with disabling firewall
    - Added QoS function
    - Added Port Triggering function
    - Added L2TP option for WAN connection type
    - Added ability to back up and restore configuration files
    - Added Wireless isolation function
    - Added ability to filter internal NAT redirection
    - Added ability to restrict access to web GUI from wireless clients
    - Added ability to filter IDENT port 113
    - Resolves issue with HeartBeat WAN connection
    - Added support for 40/56bit cipher to support old browsers to use https
    - Resolves issue with PPTP passthrough
    - Changed WPA Group Key renewal time range to 600~7200 seconds
    - Added IGMP proxy support
    - Added ability to allow web GUI access only through https or http
    Firmware 2.02.2
    - Updated wireless driver to support all versions of WRT54G hardware
    - Adds support to allow WAP54G connect as a repeater
    - CTS protection mode set to disable by default to improve wireless performance in normal environments
    - Resolved issue where the WLAN LED stays on even when wireless is disabled
    - Resolved security vulnerability causing the web server in the router to crash
    Firmware 2.00.8 (WRT54G v.2 only)
    - Updated wireless driver
    Firmware Version 1.42.2
    - Updated wireless driver to 3.31.15
    - Added URL and contents filters
    - Added L2TP passthrough
    - Added HeartBeat Signal support
    - Resolved issue with Connect on Demand
    Firmware Version 1.41.2
    - Updated GUI format and layout
    Firmware Version 1.30.7
    - Adds UI control to enable/disable frame bursting
    - Resolves issue with firmware upgrade error in Internet Explorer 6.0.2800.1106.xpsp2.030422-1633, on Windows XP pro.
    - Send 192.168.1.1 to disable DynDNS
    - Resolves issue with using the 4th tx key for WEP
    - Resolves issue with disconnecting PPPoE causing WPA to be disabled
    Firmware Version 1.30.1
    - Adjust PPTP max MTU value from 1400 to 1460
    - The router is now certifiable for the UPnP logo
    - Complies with final 802.11g standard
    - Improved performance asymmetry between the transmit and receive paths
    - Receive Broadcast packets from renew state. Some DHCP server (Dlink 300G+) send broadcast ACK after it receives a REQUEST
    - Fix: The firmware upgrade will fail, if DDNS updates while upgrading
    - Fix: If first DNS address fails, the second or third DNS address will be used to resolve domain names
    - Added the following items under Setup Page: 
        - Router Name
        - Manual Time Server
        - MAC Clone
        - wireless domain
        - Security Settings
    - Added the following items under System Page
        - UPnP enable/disable
        - Ping Test and Traceroute
    - Added the following items under Wireless Page
        - CTS Protection Mode
        - Basic Rate
    - Added the following items under Status Page
        - Router Name
        - Start IP Address
        - End IP Address
    - Added Wi-Fi Protected Access(TM) support including AES and TKIP encryption
    - Resolves issue with Port Forwarding name showing up as garbage characters
    - Added "B-Only" option to wireless modes
    - Added "Default" option to Basic Rate settings
    Firmware Version 1.02.1
    - Incorporates updates found in the Draft IEEE 802.11g version 6.1 specification
    - Resolves interoperability issues with legacy 802.11b devices under Mixed Mode
    - Resolves a performance bug where the performance in a mixed b, g network did not go up once the last b client disassociated
    - Resolves issue where WEP degrades performance
    - Resolves issue with TZO DDNS Service
    - "Domain Name" replaces "name"
    - TFTP server will only verify image file name "xxxx.bin"
    - MAC Address Filter under the Advanced tab works on both wired and wireless clients
    - Fixed a bug that prevented wireless clients from connecting to the Internet if there was no active wired PC (PPoE customers in Europe and China only)
    - Support for UPnP enabled applications such as MSN Messenger
    - Fixed a bug that caused computers connected to the LAN ports to be dropped at some interval only to be immediately re-connected
    - Fixed Dynamic Routing issue between 2 Routers
    - Allows User to name Static Route Configurations
    - Modified PC List Web Page to avoid confusion
    - Stabilized Wireless-G to LAN and WAN Throughput
    - Stabilized Wireless-B to LAN and WAN Throughput
    - Improved LAN-WAN Throughput
    Firmware Ver.: 1.01
    - Initial release

    History.
    Linksys released the 4.30 firmwares for the WRT54GL model which are compatible with the WRT54Gv1-v4.
    I guess some people were confused to see WRT54GL on the web interface of the router although they had a WRT54G.
    Thus they re-released the firmware for the WRT54Gv1-v4 with 4.21.* showing the correct model name.
    You should be able to use either firmware for either router. If you check the release notes of 4.21.* and 4.30.* you'll notice that they basically have the identical history of changes. 4.30 is now a little bit more advanced if you look on the WRT54GL downloads page.

  • Make Eyebeam 1.5 work threw WRT160N with firmware 1.02.2

    Greetings:
    I have an eyebeam 1.5 that I have tried and tried to get to work with my WRT160N with firmware 1.02.2 with zero sucess.  The Eyebeam will work perfectly when hardwired to the cable modem but will not work via the WRT160N wireless router.  Please help and tell me what to do do get this to work.  The eyebeam does not use an ip address to connect to the service but rather a domain name netcenter.republicsolutions.net. In the settings IP address is set to discover global address STUN is turned on and is set to discover server and ICE is enabled as well and xtunnels is set to never.  In the presence tab it is set to "peer to peer".  In the security tab  signaling transport is set to "automatic"
    Also the Eyebeam works perfectly on the wirelss router at work so this is indeed a Linksys issue.
    Thanks

    Well try to upgrade the firmware of the router which can be downloaded from the Linksys/Cisco website. Once the firmware is downloaded, you can proceed with the firmware upgrade even without Internet connection.
    • To prevent upgrade failures make sure that your computer is connected to the router using an Ethernet cable for stable connectivity. Upgrading the firmware wirelessly may cause permanent damage to the router since wireless connection may be unstable during the process.
    • Use a different Internet browser if Internet Explorer doesn’t work or use a different computer to perform the upgrade.
    • To prevent failure disable firewall to ensure that the upgrade will not be disrupted.
    • Make sure that you downloaded the correct firmware and version for your device to prevent technical problems that may damage the router.
    Here is the link for Upgrading the Linksys router's firmware: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=e9c2361ee7974d75913e61386a712188_4030.xml&pid=80&r...
    After upgrading it is recommended to reset the router, then reconfigure it again and then check the status.

  • WRE54G expander setting static ip address, then no internet?

    I have set a static ip address on my wired computer for the expander. I can access the setup page, but not the internet. So, I went and set my computer back to " obtain ip address automatically ". Now I can access internet, but not the expander set up page.  I would like to upgrade my firmware, but  need internet and setup page at same time to do this.
    I thought once you set up a specified ip address and added it to your gateway you could then access it anytime when you had the settings changed back  to " obtain an ip address automatically " ? 

    Download the firmware when you have Internet Access, you may download the firmware from here , once the firmware is downloaded you can set-up static ip address on your computer and access your range expander set-up page and upgrade it's firmware...Once the upgrade is done you should reset and re-configure your range expander...
    Make sure you have identical wireless settings on your Range Expander and your Wireless Router...Your Range Expander should be in the same subnet as that of your router...

  • Firmware update on a Macbook Air 2011

    Hello guys, i have a Macbook Air 2011 that had the hard drive damaged, i installed a new one so him only starts on the Utility Page for Reinstall the OSX...
    This version of Mac Air are with troubles to Download/Reinstall the OSX using the Utility Page, him needs a Firmware Update to fix, but i just can't open that Update on the Utilities Page, i tried to put the Update Archive on a Pendrive using other Mac, and i just put the pen drive on the Mac Air and tried to execute the update file using the Terminal, but i got the error: cannot execute binary file.
    So how i can fix that Mac?
    I can't execute the Firmware update, and without fix the firmware update i can't install the Osx, i also tried to install a new version using the USB Drive Bootable Mountain Lion, but this kinda of Macs Air 2011 only accept a custom Lion OSX, that can be downloaded after the Firmware fix..
    Hope someone can help!
    Thanks

    You replaced the the SSD in a MBA that cannot be user serviced, so that's quite an accomplishment. Your model does not require a firmware update to use Internet Recovery - Computers that can be upgraded to use OS X Internet Recovery. Here's the process you follow:
    Install Mavericks, Lion/Mountain Lion Using Internet Recovery
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Internet Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND-OPTION- R keys until a globe appears on the screen. Wait patiently - 15-20 minutes - until the Recovery main menu appears.
    Partition and Format the hard drive:
    Select Disk Utility from the main menu and click on the Continue button.
    After DU loads select your newly installed hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed. Quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion. Mavericks: Select Reinstall Lion/Mountain Lion, Mavericks and click on the Install button. Be sure to select the correct drive to use if you have more than one.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
    This should restore the version of OS X originally pre-installed on the computer.

  • Really annoying Internet Connection problem, please help!!!

    At first my macbook ran perfectly, but about a month ago i started running into this problem. Everytime i boot my computer up at home it acts like im connected (bars...it even checks my email using gmail notifier which is running)...then after about 20 seconds or upon opening a browser it boots me off.
    -if i use the pulldown menu to get my network it fails to connect, if i hit reconnect after that it fails to connect and i have to restart in order for it to work.
    -the only way i can get it to work is from the pulldown go to "open internet connect" then from that pulldown select my network.
    does anyone know what the problem is here? it is terribly annoying to to be able to just boot up and surf.
    another, not terribly important question as i dont use windows much...if im using the mac side, then reboot onto windows my internet dies after about 2 minutes every time. If i just boot up windows without having been in mac first it doesn't do this. (and the only fix is to unplug and then plug back in the router).
    thanks for any help,
    Jeremy

    I am seeing a similar problem at home.
    We have two existing PowerBooks and an iMac G5 which all connect to my Airport Extreme basestation with no problems.
    We just got a MacBook Pro which is having a lot of trouble staying on the airport wifi network. It keeps dropping off and when I attempt to reconnect, it gets an error doing that and offers to retry. The retry always fails.
    This seems to happen if the MacBook is idle for a time and comes back up. I am running the airport environment as pure 802.11G only with WPA encryption. This feels like it is an issue with the wireless card in the MacBook Pro as our other machines in the exact same area do not have the problem.

  • Westell 7500 (2nd one) intermitant internet, timed out pings.. etc etc

    welll, where to start,
    About 1 week ago we started having issues with slow too no internet. 
    Let it go for a day or so before I called Verizon.
    The automated lady does a line test. They see a problem. I end up talking with a person, run through all the normal stuff.
    They send out a tech.
    When the tech comes he deduces quickly that I have line issues.
    So he orders a new run to my house made. I guess.
    Next day around 3:00 pm the internet dies completely. Dead. Blinking DSL light no internet light.
    So I call back up, they can't send someone that day so the next day they can.
    So I stay home yet again. 
    They came on Thursday and after about 15~20 he figures out how they wired up out side does not match up what i have in the house. So we go downstairs rewire that one port.
    It works... yeaaa.. and it is SCREAMING...
    After about 2~3 hours of surfing/game playing.. the internet dies, intermittently,  again.. back too step one.. great... 
    Soo i am furious at this time.. I call again.. after about 2hours on the phone and 4-5 different people.. i have someone coming the next day... that is day #3 for no work.. thank gawd i have tons of days to lose. The one advanced tech i talked to said well lets send you a different modem and a different model. I was happy happy .. great let's get rid of the 7500.
    So I stay home. The usual, stay here to from 8am~5pm for the tech.. At 3pm i start to worry that they forgot about me. Well i called and after 15~20 mins i find out they did .. Oh and my new modem showed up, wow that was fast. And its an 7500 *sigh*.
    Well found out the modem he wanted to give me is no longer aloud to be shipped so they shipped me the same model.
    Well after I  found out that there was no one coming i just installed the modem myself.
    I plugged it in. It works. So i am ok at this point in time.
    Well later on that night i have NO internet again. At this point time i set fire to the house. Just kidding but that is how I felt.
    sooo here some data .. 
    from right now this is what my ping to my modem looks like....
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time<1ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=6ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=6ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=7ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=6ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=2ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=5ms TTL=64
    Reply from 192.168.1.1: bytes=32 time=1ms TTL=64
    This is what my ping to the outside world looks like... to google actually.
    Reply from 64.233.169.103: bytes=32 time=51ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=68ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=53ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=259ms TTL=237
    Reply from 64.233.169.103: bytes=32 time=50ms TTL=237
    Reply from 64.233.169.103: bytes=32 time=48ms TTL=237
    Reply from 64.233.169.103: bytes=32 time=51ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=49ms TTL=237
    Reply from 64.233.169.103: bytes=32 time=46ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=47ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=45ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=44ms TTL=237
    Reply from 64.233.169.103: bytes=32 time=45ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=52ms TTL=237
    Request timed out.
    Reply from 64.233.169.103: bytes=32 time=51ms TTL=237
    Mind you this is "new lines" and "new modem".
    Any ideas?
    HELP PLEASEEEE 

    All righty .. got another tech in here... he is actually very good and is just as confused as i am... did i mention i am windows system admin for a college... well anyways... unfortunately networking is not my field..  
    I do not have good news as, i am still having problems.. about 1.5 hours after he left i got a time out again.. solid dsl no internet... 
    Mind you this is a brand new 7500 modem... 
    I have been reading about a possible issue with the modem "over heating" because of the wireless.. and that if you turn it off this issue will go away.. the timeouts that is...  I refuse to even try this as this is not a solution .. so i tried dropping my wireless down to B and no wep, just MAC address filtering... I also lengthened the amount of time that the ssid broadcast goes out... figured less is more.. less work it has to do the less heat it will produce...
    well this is to no avail.. 
    As for you people with slowness issues... cause mine really isn't slowness at this time..  They replaced the run to my telco box and that seem to help... i am getting great speeds... i just can't stay on... 
    hope any of this helps... 

Maybe you are looking for