WRV200 can be administered wireless in spite of Local Remote Access DISABLED.

I have a WRV200 with Local Remote Access disabled (HTTPS= Disable and Allow Wireless Web Access= Disable).
When I go and connect wireless to the router, I still can access the configuration in wireless mode.
What do I need to do such as to not allow the router to be administered wireless.
Message Edited by RQ on 05-17-2008 02:49 PM

The main thing to do is to stop using "admin" for your router password. Instead, put a strong password on the router, then don't tell anyone the password. Then, no one will be able to access the router's setup pages except you.
By strong password, I mean a password with 15 or more random characters, including capital letters, small letters, and digits.
Write down your password and lock it in a file cabinet. After the router has been setup, you will only need the password a few times a year.
Message Edited by toomanydonuts on 05-18-2008 06:34 AM

Similar Messages

Can i use same address pool for different remote access VPN tunnel groups and policy

Hi all,
i want to create a different remote access VPN profile in ASA. ihave one RA vpn already configured for some purpose.
can i use the same ip address pool used for the existing one for the new tunnel-group (to avoid add rotuing on internal devices for new pool) and its a temporary requirement)
thanks in advance
Shnail

Thanks Karsten..
but still i can have filtering right? iam planning to create a new group policy and tunnelgroup and use the existing pool for new RA and i have to do some filetring also. for the new RA i have to restrict access to a particualr server ,my existing RA have full access.
so iam planning to create new local usernames for the new RA and new group policy with vpn-filter value access-list to apply for that user as below, this will achive waht i need right??
access-list 15 extended permit tcp any host 192.168.205.134 eq 80
username test password password test
username test attributes
vpn-group-policy TEST
vpn-filter value 15
group-policy TEST internal
group-policy TEST attributes
dns-server value 192.168.200.16
vpn-filter value 15
vpn-tunnel-protocol IPSec
address-pools value existing-pool
tunnel-group RAVPN type ipsec-ra
tunnel-group RAVPN general-attributes
address-pool existing-pool
default-group-policy TEST
tunnel-group Payroll ipsec-attributes
pre-shared-key xxx

I can't print wirelessly using Airport Express. I have my HP printer connected to a USB hub, and the hub to the Airport Express, but when I select the HP from the printer list, my MacBook says the printer is "off-line" - even when it is not.

I can't print wirelessly using Airport Express. I have my HP printer connected to a USB hub, and the hub to the Airport Express, but when I select the HP from the printer list, my MacBook says the printer is "off-line" - even when it is not. I've tried several USB connectors, and several different ports on my USB hub; same result. I need to have the HP connected to the hub 'cause from there it's connected to our desktop Mac.

Hi,
I am currently replying to this as it shows in the iChat Community.
I have asked the Hosts to move it to Snow Leopard (you should not lose contact with it through any email links you get)
I also don't do Wirelss printing so I can't actaully help either.
10:01 PM Friday; July 29, 2011
Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
 G4/1GhzDual MDD (Leopard 10.5.8)
 MacBookPro 2Gb( 10.6.8)
 Mac OS X (10.6.8),
"Limit the Logs to the Bits above Binary Images."  No, Seriously

How can I get Wireless N 5MHZ Capabilities Dual Band up to 300MHZ on my DV7 Laptop?

How can I get Wireless N 5MHZ Capabilities Dual Band up to 300MHZ on my DV7 Laptop?
Question for 4/18 experts ...
Or specifically, how can I replace my wireless card on a DV7-6B32US and upgrade to Intel Centrino 6230?
I have a relatively new DV7-6B32US puchased on 11/2011. Still under warranty. purchased 2 of the laptops. (also own 3 hp desktops and 1 HP All in One)
Existing card is wireless N but does not support 5GHZ or dual band. It is Broadcom 4313 wifi card and I am just realizing that the Broadcom card does not do the dual band 5GHZ wireless N. I have Linksys e4200 router which supports 5GHZ and dual band speeds up to 300 Mbps.
I called tech support and with their help identified Intel Centrino 6230 as the correct upgrade, and with their help ordered 631956-001. In the Maintenance Manual for DV7 laptop, this part number was listed for Intel Centrino 6230. Turns out HP sends an Intel Wireless N 1030 card, which is no better than my existing card. I called HP and they acknowledged that some manuals use part number 631956-001 for Centrino 6230 and some use 631956-001 for INtel 1030. So HP support said they would give refund but case manager was of no help in solving the upgrade problem. Said it was unavailable but here is your money back.
So after more searching, I see others have used part number 636672-001 to order Intel Centrino 6230, specifically for HP ProBook 4530s, 4230s, 4730s. And if I use part number 636672-001 and go thru parts store at HP, I can purchase it.
But will it work??
First, will the Intel Centrino 6230 with part number 636672-001 from HP parts, work in my HP DV7-6B32US, even though the part number is NOT listed in the Maintenance and Service Guide for my specific laptop. I see postings about whitelists and changing bios, etc, and am hoping someone can provide some guidance. I have been thru 2 tech support calls and one case manager and have gotten 3 different feedback from HP, from yes it will work and ordering the part, to buy it on amazon, to it will not work and here is your money back.
Second, I see some postings about Centrino 6230 and multiple antenna's. When I replaced the Broadcom 4313 with the Intel 1030 card, I simply unattached 2 wires and reattached the wires. And it worked. I am wondering if the reason HP doesn't list the 6230 card for DV7 is that DV7 does not have the antennas required to support 6230. Does the Centrino 6230 require 3 antennas?
Thanks for any suggestions. The existing cards do work but I paid extra for the Linksys e4200 Router and just assumed a winter 2011 $700 laptop from HP would use the latest wireless n technology, otherwise I would just keep existing cards.

I have went thru the exact same problems trying to upgrade the wireless card in my DV7. It is very frustrating that the wireless card can't be upgrade to one that supports 5Ghz. Here is my post from the network forum. http://h30434.www3.hp.com/t5/Wireless-Internet-Home/Unsupported-Wireless-LAN-6230/td-p/1419595 Doesn't sound like it is possible to upgrade to the Centrino 6230 without it being added the the "white list". Sound like HP doesn't update the list after shipping the notebook. I feel your pain. HP needs to help out the consumer in upgrading the wireless cards. I see we are not the only ones that have had this problem.

HT2250 I have been able to get my MacBook Pro to print wirelessly through my Airport device. How do I make it so other computers (non-Mac) can also print wirelessly as well? They are able to connect through my wireless network but can't print.

I have been able to get my MacBook Pro to print wirelessly through my Airport device. How do I make it so other computers (non-Mac) can also print wirelessly as well? They are able to connect through my wireless network but can't print.

Well, you could install the drivers to the wireless printer in you other computers.
blue apple > System Preferences... > sharing
check printer sharing.

How many computers can connect to wireless?

Hello, and thank you for reading!
We have a 2 TB Time Capsule with 802.11n wireless, and I was wondering if anyone knew what the maximum number of computers this thing can handle for wireless internet?
It's in a small office but occasionally we get 40 people with laptops in, and we've seen some wonky behavior during peak times. The guy who set it up made some mistakes with the networking and DHCP range, but I fixed those. Now I'm just wondering if anyone knows approximately how many people we can reliably connect to this station at once?
thanks,

canderson13 wrote:
Hello, and thank you for reading!
We have a 2 TB Time Capsule with 802.11n wireless, and I was wondering if anyone knew what the maximum number of computers this thing can handle for wireless internet?
It's in a small office but occasionally we get 40 people with laptops in, and we've seen some wonky behavior during peak times. The guy who set it up made some mistakes with the networking and DHCP range, but I fixed those. Now I'm just wondering if anyone knows approximately how many people we can reliably connect to this station at once?
Hi, and welcome to the forums.
Apple says 50: http://store.apple.com/us/product/MC344LL/A/Time-Capsule-2TB?fnode=MTY1NDA0Mg&mc o=MTMzNzU2MjI

Can't print wirelessly from iMac to HP 8600 all-in-one

A few weeks ago, I purchased a HP 8600 basic printer and setup it up to my two iMacs and to the router (cisco brand).
I haven't really printed with it since I have gotten it, which did print when I tested it at first. Now I can't print wireless from either iMac (one iMac is ver. 10.9 and the other is ver. 10.8). Both my computers and printer are connected to my router, but when I go to print something the printer dialog box tells me: "the printer is not connected."
What am I doing wrong?
Thanks

Hello Viggo_R, Welcome to the Forums
I understand you are unable to print from your 10.8+10.9 systems and would like to help out the best I can.
I have researched the issue at hand for you and have found a guide that I suggest following. Hopefully this will connect your printer back on the network and get you up and running again.
Click here to get started: Printer Does Not Maintain Wireless Connection
This guide might also be helpful: Print Jobs are Stuck in the Print Queue
Take care,
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution!

Photosmart b209a can't find wireless network.

I've only had this printer for three days. The "Easy One Button" process to get it to find a network failed. It cannot find my wireless network.
I'm using XP Professional on my laptop. McAfee Virus scanning and Firewall. (Not that it matters if the printer can't find the wireless network)
I have a DSL D-link router with NO MAC filtering and yet when I print the Wireless Network Test Report it gives me this whole spiel on MAC address filtering and asks to add the MAC address of the printer to the router... but there's no offered solution if MAC filtering is turned off.
I've changed my router security key from WEP to WPA-PSK.
I've managed to get it to connect twice... and to print a test page on separate days. I have no idea what it is I do that gets it 'online' but it doesn't seem to last.
I have spent several hours over the past three days (wasting entire days) trying to work out what the problem is. I have read forum posts; I have googled for solutions. The troubleshooting guide for the printer seems hopeless.
The printer is on the same desk as the router with only a computer monitor between them.
When I print the HP Network Configuration Page it states the status of the 802.11 Wireless is "Disconnected". The printer's wireless light is on, showing that the wireless radio is working on the printer.
I bought HP because my last printer was HP and it was excellent (but not wireless). If I can't get it to go online, seriously, I'll take it back and exchange it for a different brand of printer. All I want is a printer I can print to wirelessly, is that so hard to ask? Yes, I'm getting really frustrated here. I live in a rural area and I don't have access to geek friends or a computer professional or anything like that and returning the printer requires a two hour drive so I have to be as self-sufficient as possible. Please, try not to use too many technical terms. I can understand some but not all and if anybody can help me, please be clear in their instructions (ie, don't just say 'go to setup blah blah blah' without saying which setup you're talking about.)
Thanks for any help. It is appreciated.

Yes, the desktop is connected to the router with an Ethernet cable.
Yes the laptop is wireless.
The printer is connected to the router via wireless (which I've already stated, it keeps losing the wireless network).
If I don't have my printer connected to the desktop via cable, then I won't have any printing capability at all, because, as I just said, the printer keeps losing the wireless network! I need at least some way of printing when the printer can't find the network (even though the wireless network is working perfectly fine).
So, desktop connected to router with cable.
Laptop is wireless
Printer is wireless for laptop use (but it keeps losing the network and therefore is totally useless in that respect)
Printer is connected to desktop via cable to enable printing because of wireless continuing to lose connection to wireless network.
In fact my printer hasn't been able to connect to the wireless network for 2 days now... even though I'm currently connected to it on my wireless laptop.
Sometimes the printer finds the network, sometimes it doesn't and when it does, if I try to print from the laptop wirelessly, the printer loses the network.
This really is poor product and the installation manual might as well be used for toilet paper for all its worth, same with the 'help' feature on the disk. I only chose HP because I was familiar with it, since my previous printer was HP and reliable (but not wireless). I'm seriously wishing I'd purchased a different brand.
I'm not an IT tech, but I've managed to be able to connect modems and routers and other peripherals to my network without too much hassle at all... until now.
I'm sorry if I sound angry but this is completely frustrating. I spent good money for a product that I am unable to use for the main purpose I bought it! I'm reduced to saving things to USB sticks and physically taking them to the desktop computer and having to print from there.

TS1398 I can no longer sign in to my home fi (bt hub) with my iphone 4. Yet I can get on wireless with my laptop so the hub is working. The only thing Ive done different recently is download and use an app called Onavo mobile ltd which Ive now deleted, he

I can no longer sign in to my home fi (bt hub) with my iphone 4. Yet I can get on wireless with my laptop so the hub is working. The only thing Ive done different recently is download and use an app called Onavo mobile ltd which Ive now deleted, help pls?

Read another post in the forum about this and it appears this app also installs a profile with a proxy service that you will have to try and delete as well. Check that out.

WRT54G v6 - Can Connect to wireless network but can't access internet

Ok, this is my last resort for help. I spent two hours yesterday with linksys "chat" support to no avail.
First the techincal details:
OS for all machines = Windows XP
Laptop w/two adapters - one wired, one wireless
WRT54G v6 upgraded with 1.00.9 firmware
SpeedStream modem from DSL provider
I have manually set the IP, subnet mask, gateway, primary and secondary DNS for my wireless adapter (using the Alternate Configuration in the Internet Protocol Properties of the Wireless Network Connection). When I connect to the wireless network I see that the IP, subnet, gateway and DNS server IPs are all correct (via ipconfig /all). I see that I am connected to my SSID (11.0 MBps, signal strength Excellent) however I can't access web sites (the server not found message appears in the browser) nor can I ping the router IP or any other IP (LAN or WAN).
My wired PC works fine with this router. My laptop works fine with this router when wired.
Anyone face a similar situation and have a solution? Thanks.

A new discovery...
When I disable the wireless security on the router, I am able to connect to the wireless network, ping the router and access the internet. So, there is apparently something wrong with the WEP security (although I am able to connect to the wireless network when WEP is enabled).
I am thouroughly confused. Any help is appreciated. Thanks.

My Ipad did work on my wireless at home and works on other wireless but no longer at home. My IPhone works at home and others can use the wireless Confused that it did work and now does not?

My Ipad did work on my wireless at home and works on other wireless but no longer at home. My IPhone works at home and others can use the wireless> Confused that it did work and now does not?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Turn Off your iPad. Then turn Off the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
On your iPad go to Settings > General > Reset > Reset network settings and see if that enables you to connect.
 Cheers, Tom

Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.

Hi!
Didn't know exactly where to direct this question in the Apple Community so I chose Airport. To everyone, thanks in advance.
I’m really desperate. I’m a big Apple fan. I have two Apple MacBook Pro laptops with Mountain Lion software. I also have an Apple Airport Extreme. My HP Photosmart C4780 printer was also purchased from Apple. Anyway, my Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
This appears to be an HP printer problem. I went to HP community support with the information below but I have received no solutions outside of buying a new printer.
“Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0.”
To be straightforward, I’m no computer tech so I don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve tried everything to reconfigure without success. If I need to make these changes via Airport Extreme Utility 6.0 not easy to find not that I know what I’m doing.
Most importantly if I ever get wireless working again, do I still need Airport Extreme connection or is the AT&T U-Verse modem/router sufficient?
Any direction or help is greatly appreciated. Thank you for listening.

Thank you for your prompt response. I'll be honest I'm a retiree and a newbie to all of this stuff. I don't even know how to do a thread. (Embarassing) This is my first ever contact with the Apple Community so I'm slowly trying to figure this out as well.
As to your thread request, I'm assuming you want to read my post with HP. Not knowing how to thread, I've copied it below.
I have an Apple MacBook Pro laptop with Mountain Lion software. I also have an Apple Airport Extreme. My Internet service is AT&T. AT&T just upgraded my service with a new modem/router (AT&T U-Verse). Prior to the conversion, my wireless printer connection was working perfectly.
Now can’t print wirelessly. For your information, everything is connected via Wi-Fi. The AT&T technician stated that I no longer needed my Apple Airport Extreme, so it was removed. Naturally, after the tech leaves, we find out the HP printer wirelessly no longer works. Thinking that removing Airport Extreme may have been the problem, I reconnected it to the AT&T modem/router, however no change.
Ran the HP wireless network test report and it states that HP printer can’t find wireless router and to verify that the HP printer network name (SSID) matches the wireless router network name (SSID) exactly. The Diagnostic Summary in brief: Wireless On & Working & Security – Pass; Network Name (SSID) Found – Fail. Nothing else under diagnostic summary ran. Under Configuration Summary: It shows old SSID name and Mac Hardware Address but no IP Address.
Next ran the Network Configuration Page and everything is enabled except the 802.11 Wireless. It shows status – disconnected. Under general information it states the following: Network status - Offline; Active Connection Type - None; URL(s) for Embedded Web Server – http://0.0.0.0
To be honest, don’t know what this means or where to find. The AT&T tech provided me the new SSID Name and a wireless key number but that’s it. Also I uninstalled and reinstalled via USB. The HP message states can’t find router. At this point, I’ve read your forum and tried everything to reconfigure without success. Any direction or help is greatly appreciated.
Thanks in advance!
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
I finally figured it out! (Sorry that I'm replying to my own posts btw, but I want to post the solution for anybody else with the SigmaplusEOL1 problem). If you have the SigmaplusEOL1 as your SSID when you print the "Wireless Network Test Report", you do NOT need to return it (I know that's hassle for people). To fix the problem, follow these steps.
1) Unplug your printer.
2) Go to your router's IP address (like 192.168.1.1 or whatever it is for your router).
3) Change the SSID of your wirelss network to "SigmaplusEOL1".
4) For the Security option for your wireless network select none (so that a password is not required to access your wireless network).
5) Power your printer back on and reprint "Wireless Network Test Repor". It should say "No problem found..."
6) The report should also have a the IP Address of the printer (under Configuration Summary at the bottom). Type that IP Address in your browser to get to the printer's settings page.
7) Click the "Network" Tab at the top.
8) Under the "Connections" header in the left pane, click "Wireless (802.11).
9) Click "Start Wizard" at the bottom right.
10) In the wizard, change the SSID and encryption (wep or wpsk) password to whatever you want your wireless network to be. So probably whatever it started out as before you changed the SSID to SigmaplusEOL1
11) Click "Finish" at the end. The page will probably try to keep loading but it won't because you changed the network settings of the printer. Just ignore that
12) Go back to your router's IP address and change the SSID and encryption password to whatever you changed the printer's SSID and password to.
13). Reprint the Wireless Network Test Report. It should say the SSID is the same as your wireless, and everything is good.
That's it. You should be good to go now.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Thank you for your prompt response. This has been a totally frustrating experience. I’ve spent at least 8 hours trying to fix this. My HP problems and your initial steps were identical to mine. I am by no means a tech person and my computer tech knowledge is minimal. However I followed your steps to the best of my ability.
I did get the SigmaplusEOL1 message. I was able to get to Step 6 where the wireless network test report now reads – “HP printer settings do not match your wireless router settings.” So I guess this is a step in the right direction. However unfortunately the Configuration summary message for the IP Address reads – “Not Applicable”. (Note: changing SigmaplusEOL1 to network name knocked out my Internet access. Had to switch back to regular network name to regain access.)
I’m at a loss as to what to do next.   Without the IP Address is it possible to move forward? As I stated earlier, I’m not a tech person. As to your steps 7, 8 and 9, I can’t find them on my computer or maybe I’m looking in the wrong places. In System Preferences - Network, I have none of these steps. If you’re referring to Airport Utility, with the changes in Mountain Lion, these steps are no longer there. If you’re talking about Safari, Firefox or HP, now I’m really lost.
Finally, I don’t know if you can answer this or not. If I ever get wireless working, do I still need Airport Extreme or is the AT&T U-Verse modem/router sufficient?
Again thank you for your time and patience.
Re: Can't connect wirelessly HP Photosmart C4780 to MacBook Pro OSX 10.8.2 Mountain Lion.
Unfortunately I am unable to offer any further advice as I only followed the instructions listed on the other page.
Finally, as to having WEP enabled, I don't know. Don't even know where to look. The best that I could determine is that my security is WPA/WPA2 Personal.
I'm truly sorry about all of this. Thank you for your time and patience. After reading all of this and you change your mind, I would understand.

MacBook Can't Print Wirelessly on Officejet Pro 8500A

I just got an Officejet Pro 8500A and it can't print wirelessly in by wife's MacBook, but it can print with a USB port. It can also print off my HP laptop wirelessly which has windows 7.

What version of OS X on your wife's Mac?
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Can i print wirelessly from iPhone to HP OfficeJet 4500 Desktop Wireless All-in-One Printer ?

i just bought a new printer and its not apper in my iphone how can i print wirelessly ? from iphone ?

the HP iPrint app was replaced by the HP ePrint Home & Biz app. The best source of iPad/iPhone printing compatibility information is the HP support page for Cloud services. Click on the section "HP OfficeJet Products" to see a chart detailing AirPrint, ePrint and HP ePrint Home & Biz compatibility for each OfficeJet product.
Note that OfficeJet 4500 is a family of printers, each with different capabilities. When purchasing it is important to identify the manufacturer number e.g. the CB867A and the CN547 are both HP OfficeJet 4500 printers but the latter has wireless networking and the former does not. I suspect the above support page applies to the entire product family.

Can't configure wireless settings on P1102w using a mac

Hi there. I can't configure wireless settings on P1102w using a mac. I have it installed with USB just fine but I want to use eprint (with ios airplay). I run the setup utility looking for some wireless setup option, but it never appears. When I finish the install it tells me to go to the eprint website to download eprint. At that site it has me download the firmware update, which I do, and then at the end of that it tells me to go to the eprint website again, which then downloads the firmware update again. It's an endless loop.
I know I need to get to the built in web server but the config page tells me I don't have an IP address. Which makes sense to me because it hasn't been set up. I can't for the life of me find how to set up the wireless using the driver software on the Mac OS. I try to follow the manuals instructions, but it looks like it is designed for windows users, and the buttons it tells me to look for just don't exist on the mac HP driver software.
Can you help?

Hi,
The Wireless configuration should be made by using the EWS page, which also accessible from Mac OS over a USB connection through the printer setup.
You may find the steps listed below:
Click the Apple icon, then clickSystem Preferences.
Click Print & Fax.
Select your printer and click Open Print Queue.
Click on Printer Setup
Then select Utility
Click Open Printer Utility
Click HTMLConfig. The EWS opens.
Click the Networking tab
Then click Wireless from the list on the left
Under Communication Mode, click Infrastructure, select your network SSID from the Available Network Names (SSID) list, and then click the << button.
From the Security Mode pop-up menu under Authentication, click WEP or WPA/WPA2. Your selection depends on which Wireless Security Protocol your network uses.
Type your WEP/WPA/WPA2 key in the appropriate field, and then click Apply.
In the confirmation box, click OK and then close the HTML Config and Print Queue windows.
Once done, allow 3 minutes to fully establish the connection, then unplug the USB.
Enter Print & Fax and remove the existing USB Print Queue.
Click the Plus button and add the printer over the network.
Please let me know of any issue,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

WRV200 can be administered wireless in spite of Local Remote Access DISABLED.

Similar Messages

Maybe you are looking for