WRV200 PPTP WAN - Default GW is not pointing to tunnel

Hi all,
I am currently testing this WRV200.
We have a PPTP server serving IP range from 192.206.59.1/24
There is no problem with the authentication and tunnel establishment.
Just that after the tunnel is established, the default gw in WRV200 is not pointing to the tunnel, but it's still pointing to the gateway on the WAN.
Since we have chosen the WAN type to be PPTP, the default gateway should be defined on the PPTP tunnel, isn't it?
Attached is some screenshot.
Thanks!

alegalle wrote:I am a liitle confused because of what you are asking and also the screenshots posted.You stated that the WAN is configured for PPTP and it's gateway should be that tunnel. But the screenshot you have of the WRV does not reflec the IP scope of the PPTP server. The highlighted value would be correct as any unknown destination would be sent out the WAN interface. The router also already knows about 192.70.172.0 netwrok and it is attached to its WAN interface.So maybe I did not fully understand your question. From what you have posted it appears that you have a WRTR connecting to the cloud via PPTP and on its LAN we have the WRV connected via its WAN port. In other words like this:CLOUD >> PPTP conn. >> WRTR (WAN: 192.206.59.1 / LAN: 192.70.172.2) >> WRV (WAN *this is the part thats confusing / LAN: 192.168.0.1)I guess I just dont see why the WRV would send all traffic to 192.206.59.0 when it is not a directly attached network. What problems are you encountering with your configuration?
In PPTP connection, there is no need for the gateway to be in the same subnet.
Because in the WAN setup screen, we have selected the connection type to PPTP, therefore, the default GW must be pointing to the PPTP gateway.
The same goes for PPPoE isn't it?
In the WAN setup screen, if we have selected the connection type PPPoE, the default GW must be pointing to the PPPoE gateway.
Just that in PPPoE mode, it is usually deployed over copper wires only.
For PPTP connection, we can deploy it over normal IPv4 network.
May I know what is the WRTR?

Similar Messages

The Default Gateway Is Not Available / Problem

Hello, I recently purchased this HP Pavileon laptop, and I've been encountering this problem very often (every 2-10 minutes). This problem is getting extremely frustrating as absolutely nobody has been able to provide a fix for this issue.
When the laptop is on battery mode (this does not happen when plugged in); I commonly get disconnected from my wi-fi connection and to fix it, I must run the troubleshooter. This temporarily fixes the issue by resetting the wi-fi adapter.
What I have tried and has not worked:
* Turn off to save power option in the driver settings (in Device Manager) untickets
* Updated drivers
* New power plan
* Tried different drivers
* Complete system restore
The wireless adapter is Realtek RTL 8188EE. Upon running the troubleshooter, this is all the information from the detailed information section:
Windows Network Diagnostics
Publisher details
Issues foundThe default gateway is not available
The default gateway is not availableThe default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Fixed
Reset the "WiFi" adapter
Completed
Investigate router or broadband modem issues
Not run
Issues found
Detection details
6The default gateway is not availableFixed
The default gateway is a device that connects a local network or computer to the Internet. A broadband modem or router is usually the default gateway.
Reset the "WiFi" adapterCompleted
This can sometimes resolve an intermittent problem.
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Repair.1.etl Investigate router or broadband modem issuesNot run
If you're connected to a hotspot or domain network, contact the network administrator. Otherwise: 1. Unplug or turn off the device. 2. Once all the lights on the device are off, wait at least 10 seconds. 3. Turn the device on or plug it back in to the power outlet. To restart a router or modem that has a built-in battery, press and quickly release the Reset button.
Detection details
Diagnostics Information (Network Adapter)
Details about network adapter diagnosis:
Network adapter WiFi driver information:
Description . . . . . . . . . . : Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Manufacturer . . . . . . . . . : Realtek Semiconductor Corp.
Provider . . . . . . . . . . . : Realtek Semiconductor Corp.
Version . . . . . . . . . . . : 2012.2.827.2013
Inf File Name . . . . . . . . . : C:\WINDOWS\INF\oem8.inf
Inf File Date . . . . . . . . . : 12 September 2013 10:17:00
Section Name . . . . . . . . . : HP8188ee.ndi
Hardware ID . . . . . . . . . . : pci\ven_10ec&dev_8179&subsys_197d103c
Instance Status Flags . . . . . : 0x180200a
Device Manager Status Code . . : 0
IfType . . . . . . . . . . . . : 71
Physical Media Type . . . . . . : 9
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Connection incident diagnosed
Auto Configuration ID: 1
Connection ID: 1
Connection status summary
Connection started at: 2014-07-24 04:19:49-759
Profile match: Success
Pre-Association: Success
Association: Success
Security and Authentication: Success
List of visible access point(s): 0 item(s) total, 0 item(s) displayed
Connection History
Information for Auto Configuration ID 1
List of visible networks: 1 item(s) total, 1 item(s) displayed
BSS Type PHY Security Signal(RSSI) Compatible SSID
Infra <unknown> Yes 100 Yes Matt
List of preferred networks: 1 item(s)
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Set by group policy: No
Connect even if network is not broadcasting: No
Connectable: Yes
Information for Connection ID 1
Connection started at: 2014-07-24 04:19:49-759
Auto Configuration ID: 1
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Pre-Association and Association
Connectivity settings provided by hardware manufacturer (IHV): No
Security settings provided by hardware manufacturer (IHV): No
Profile matches network requirements: Success
Pre-association status: Success
Association status: Success
Last AP: 98-fc-11-88-61-b8
Security and Authentication
Configured security type: WPA2-PSK
Configured encryption type: CCMP(AES)
802.1X protocol: No
Key exchange initiated: Yes
Unicast key received: Yes
Multicast key received: Yes
Number of security packets received: 0
Number of security packets sent: 0
Security attempt status: Success
Connectivity
Packet statistics
Ndis Rx: 34302
Ndis Tx: 32619
Unicast decrypt success: 0
Multicast decrypt success: 0
Unicast decrypt failure: 0
Multicast decrypt failure: 0
Rx success: 0
Rx failure: 0
Tx success: 0
Tx failure: 0
Tx retry: 0
Tx multiple retry: 0
Tx max lifetime exceeded: 0
Tx ACK failure: 0
Roaming history: 0 item(s)
Diagnostics Information (Wireless Connectivity)
Details about wireless connectivity diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Auto Configuration
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Result of diagnosis: There may be problem
Diagnostics Information (Wireless Network Adapter)
Details about wireless network adapter diagnosis:
For complete information about this session see the wireless connectivity information event.
Helper Class: Native WiFi MSM
Initialise status: Success
Information for connection being diagnosed
Interface GUID: 7c04789b-0b43-472c-abd6-a84cb31e9053
Interface name: Realtek RTL8188EE 802.11b/g/n Wi-Fi Adapter
Interface type: Native WiFi
Profile: Matt
SSID: Matt
SSID length: 4
Connection mode: Infra
Security: Yes
Connect even if network is not broadcasting: No
Result of diagnosis: There may be problem
Network Diagnostics LogFile Name: 2D0FE1F0-C2C2-43B5-A857-2D2B3C4B8A51.Diagnose.0.etl
Other Networking Configuration and LogsFile Name: NetworkConfiguration.cab Collection information Computer Name: LAPTOP Windows Version:6.3Architecture:x64Time:24 July 2014 04:34:47
Windows Network Diagnostics Detects problems with network connectivity. Package Version:1.0Publisher:Microsoft Windows

Run the HP Support Asssitant's Tune up application. There should be a new BIOS available. sp66866
Have you installed the latest Windows 8.1 updates?
Do not install optional video graphics updates.
I was runnning into a similar problem with my HP product loan Envy Spectre 13 TouchSmart Ultrabook until I did the updates. I had upgraded my wireless router to a model with 802.11AC specification.
Invoke the Device Manager and ensure that the box next to Allow this computer to turn off this device to save power is unchecked.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Creating physical standby db through grid control 11g fails with "default listener is not running"

On step 4/6, i am getting error like below
ErrorExamine and correct the following error(s), then re-try the operation.Default Listener in Grid Infrastructure - The default listener in the grid infrastucture is not running.
I have the listener running on grid user and grid home, 11.2 in both primary and standby.
During these steps till 4, its no where asked for grid user password.
Not sure how it will detect the grid home listener.
Listener is running with default port 1521 on both the servers primary and standby
On the step 4 screen the other option for default listener is non-default listener and its pointing to db home and not grid home.
So i guess oracle is looking for the listener to be up on the db home and not on grid home causing the issues,
if so how to fix this ?
I am using role separation, separate user for grid and oracle homes grid and oracle user and all are on 11.2.0.1 db + grid

Hello again;
Check the solution in this: ( and note the multiple versions of oracle it covers )
UNABLE TO FIND GRID INFRASTRUCTURE LISTENER (Doc ID 1483234.1)
Best Regards
mseberg

RV220W PPTP Start IP Address must not be in the subnet of LAN:192.168.1.1/255.255.255.0

Hello,
I start setup of new RV220W Wireless router.
I want to provide access to internal network via PPTP.
But gettting error 'PPTP Start IP Address must not be in the subnet of LAN:192.168.1.1/255.255.255.0'.
I reviewed the forum and some user's says what they can fix this issue, but I cannot found the way how to do it.
Details of router:
Firmware Version
1.0.4.17
LAN (Local Network) Configuration
IP Address
(xxx.xxx.xxx.xxx)
Subnet Mask
(xxx.xxx.xxx.xxx)
DHCP
DHCP Mode
None DHCP Server DHCP Relay
Domain Name
Starting IP Address
(xxx.xxx.xxx.xxx)
Ending IP Address
(xxx.xxx.xxx.xxx)
Primary DNS Server
(Optional)
Secondary DNS Server
(Optional)
Lease Time
Hours (Range : 1 - 262800, Default : 24)
Remote DHCP Server
LAN (Local Network) Proxy
DNS Proxy
Enable
VLAN
Enable
Create VLANs and assign the Outgoing Frame Type.
Up to Fifteen new VLANs can be created. VLAN IDs must be in the range (2 - 4093)
VLAN Membership Table
VLAN ID
Description
Inter VLAN Routing
Device Management
Port 1
Port 2
Port 3
Port 4
1
Default
Enabled
Enabled
Untagged
Untagged
Untagged
Untagged
Multiple VLAN Subnet Table
VLAN ID
IP Address
Subnet Mask
DHCP Mode
DNS Proxy Status
1
192.168.1.1
255.255.255.0
DHCP Server
Enabled
VPN Users
PPTP Server Configuration
PPTP Server
Enable
Starting IP Address
(xxx.xxx.xxx.xxx)
PPTP Start IP Address must not be in the subnet of LAN:192.168.1.1/255.255.255.0
Ending IP Address
(xxx.xxx.xxx.xxx)
VPN Client Setting Table
No.
Enabled
Username
Password
Allow User to Change Password
Protocol
0 results found
All settings after reset to factory settings.
How I can enable assigning the IPs from LAN network to the PPTP Server?
Thank you!

Hi,
This is a change done explicitely starting firmware 1.0.4.17. It is not a bug. This appears to be by design. PPTP peer networks are now treated as a routed subnet. It is unlikely that this will be changed.
But nevertheless there is a workaround to configure the PPTP range in the same subnet as your LAN:
1. Configure LAN IP subnet different from what you will use, for example 192.168.2.0/24
2. Configure DHCP pool for PPTP client as needed for example 192.168.1.100-192.168.1.110
3. Go back to LAN interface and change LAN IP to desired one: 192.168.1.0/24 and pool 192.168.1.2-192.168.1.99
4. This way there will be no error on GUI
5. PPTP client will receive IP address from the same subnet as LAN interface of the RV220W
Regards,
Kremena

Default Value is not getting displayed in SUN ONE Ldap

Hello,
I have created an attribute in slapd.user_at.conf and it is associated in slapd.user_oc.conf.
The attribute default value is given through SUN ONE Console. But, In our application the default value is not getting displayed.
We need the default value to run our applicatin. Can anyone help me for this issue
Regards,
K. Senthil Kumar

Hi anandkumar,
I belive this issue can be resolved by changing the Query proprties for the perticular field.
Kindly check the Field proerties in query designer and ensure that Text is enabled ather than Key.
__Field property check up:__Go to query designer->click onn the field-> Right hand side in properties click on display tab-> select Text in drop down menu of Display as tab.
FURTHER CHECK UP: check the master data avaiulability for the perticular info object, if masterdata is not available, do the text data for txt data availability in report level.
Hope this helps you!!
Best Regards,
Maruthi

Why the default value is not the Oracle recommended?

Why the default value is not the Oracle recommended?
In Oracle 10g, the default alocated unit of Oracle ASM is 1MB. But the Oracle ducumentation states that "To ensure a higher probability of one
logical I/O resulting in no more than one physical I/O, the minimum stripe depth should be at least twice the Oracle block size". ---See Performance Tuniing Guide (10g10.2 Page8-3.
It's inconsistent. What is right way?

>
Why the default value is not the Oracle recommended?
In Oracle 10g, the default alocated unit of Oracle ASM is 1MB. But the Oracle ducumentation states that "To ensure a higher probability of one
logical I/O resulting in no more than one physical I/O, the minimum stripe depth should be at least twice the Oracle block size". ---See Performance Tuniing Guide (10g10.2 Page8-3.
It's inconsistent. What is right way?
The default database blocksize of 10g is 8k.
>
8 * 128 = 1024
128 >= 2
At least twice the size does not mean exactly the doubled size.
There is no contradiction between the documentation and your observation in this case.
Kind regards
Uwe
http://uhesse.wordpress.com

Removing warning for "Default CSS file not found."

I am getting this warning in Flash Builder:
"Default CSS file not found."
I can not for the life of me figure out how to get rid of it. Any suggestions?

Default css file can be specified as a compiler option (per SWC, I think).
See http://livedocs.adobe.com/flex/3/html/help.html?content=compilers_14.html
For example, flex framework has a default CSS file: C:\Program Files\Adobe\Adobe Flash Builder 4\sdks\3.5.0\frameworks\projects\framework\default.css
Do you have some library project or a swc with default css file option turned on, but the css file is missing?

By default, Teststand will not include the test step result in subsequence, is there any way to include these step result in report?

By default, Teststand will not include the test step result in subsequence, is there any way to include these step results in report?
Thanks
Jacky

Hi,
If your subsequence is in a separate sequencefile, then check the properties of the sequencefile to make sure that the record has not been disabled.
Regards
Ray Farmer
Regards
Ray Farmer

Firefox plays video, but no sound. when I type about:plugins in location bar, it shows the firefox default plugin is not enabled. When I look at my plugins, it says it is enabled. I have uninstalled 3.6 and re-installed with the same result.

firefox plays video, but no sound. when I type about:plugins in location bar, it shows the firefox default plugin is not enabled. When I look at my plugins, it says it is enabled. I have uninstalled 3.6 and re-installed with the same result. Why do I have no sound. Computer plays I-tunes and all other sounds, just no web browser sounds.

Glad you seem to have sorted things out.
The warning about the warranty is light hearted, I think at one stage it warned "here be dragons" but also intended to make us think as it warns that making changes may produce problems.

Forwarding an email TB changes account to one of my other accts which is not the default acct & is not acct from which msg was sent (which was default acct)

forwarding an email TB changes account to one of my other accts which is not the default acct & is not acct from which msg was sent (which was default acct)
how do I make TB keep the same account (which is my default account anyway) from which I sent the original email which I'm now forwarding?
Thanks !

Do you have Gmail? Google has some funny rules which might apply; see https://support.mozilla.org/en-US/kb/configure-origin-address-for-multiple-gmail-accounts

I use a HP Officejet Pro 8500 A909a printer and my Safari always put 150% size as default. Wy not 100%?

I have a MacBook (the white one) and use a HP Officejet Pro 8500 A909a printer and my Safari always put 150% size as default. Wy not 100%?
When I use Firefox the default size is 100%. When I use Pages, also runs good (100%). Only in Safari, and Mail too, appears 150% as the default size.
How can I change it to 100% in both?
THOMAS

Hi,
The problem seems to lie in the installer, which has an unusual bad behaviour. The installer puts the 8500 a909a in the list of USB bootable devices. (Not good!!!)
When the printer is disconnected it isn't a problem. When the printer is connected the computer tries to boot from the printer and the computer hangs.
When I found the printer in the BIOS list of USB bootable devices I DISABLED that item in that list. Then it booted normally.
But now the BIOS takes an extra 30 seconds or so but boot up seems to be preceeding normally.
The guys on the CHAT and PHONE lines didn't even imagine the installer might be a problem so their advice was useless. They were blaming the computer. More importanly, they didn't have a way to escalate the problem. They had no capacity to respond in a flexible manner. It was like dealing with unhelpful staff in the county clerk's office.

LSMW - Logical File Path not pointing to Physical Path

Hi All,
I'm trying to upload some MIGO goods movement transactions through LSMW. I'm to step 7, specifying files, and am getting the error "No logical file path has been specified. I saw another thread which helped me, but I am still stuck after reading it.
Re: Error in Creation of Purchase Requisition through LSMW
I have gone into transaction FILE and created the logical file name MM_GOODS_MOVEMENT, and set the physical file as the .lsmw.conv converted data file as the above thread says. I also tried using the logical path LOCAL_TEMPORARY_FILES for the converted data, but I get the error telling me that the path does not point to a physical directory. I then tried creating my own file path, and setting the path to my desktop where the source file is, and the same error occurred.
Does anyone know why it is not recognizing the physical path maintained in the logical path?
Thanks,
J

Thanks for both replies,
I have full authorization across all transactions in the sandbox system I am working in, so that is not an issue. I filled the logical path field in the MM_GOODS_MOVEMENT logical file with LOCAL_TEMPORARY_FILES, as well as trying my own created file path, and I recieved the same error for each. Here is how the config is currently:
Logical File Path Definition: MM_GOODS_MOVEMENT
Syntax Group: WINDOWS NT
Physical path: C:\Documents and Settings\jchanski\Desktop\<FILENAME>
or,
Logical File Path Definition: LOCAL_TEMPORARY_FILES
Syntax Group: WINDOWS NT
Physical path: C:\temp\<FILENAME>
Logical File Name Definition: MM_GOODS_MOVEMENT
Physical file: MM_MM_MIGO_INVUPLOAD.lsmw.conv
Data format: ASC
Applicat.area: MM
Logical path: LOCAL_TEMPORARY_FILES or MM_GOODS_MOVEMENT
Do you see any error with this Brajvir? Thanks!

Default Mail app not working with yahoo mail. Won't update.

Default Maill app not working with Yahoo Mail.
It stopped working the other day. I tried everything but it wouldn't update new mail. The yahoo account itself is fine because I can see new mail on Yahoo or a yahoo app.
I tried deleting the account and putting it back on, but now it has 0 mail in any part of it. Nothing has synced.
What do I do?
iPad 2 latest OS.

A lot of people have been unable to access Yahoo e-mail on their iPhones or iPads. My wife’s iPad was not downloading Yahoo mail, although her iPhone was. Both used IOS 8.2. We tried deleting the account several times and troubleshooting all of the other settings. The problem appears to have been that allowing the IOS to automatically create the account on the iPad resulted in the wrong settings for the incoming server. The following procedure, pieced together from two websites, fixed the problem for us. So far, so good.
https://portal.smartertools.com/kb/a2659/configure-imap-for-iphone-or-ipad.aspx
https://help.yahoo.com/kb/mobile-mail/imap-server-settings-sln4075.html
On the iPhone, tap Settings.
Tap Mail, Contacts, Calendars.
Tap your Yahoo account, then delete it.
Tap Add Account.
Tap Other.
Tap Add Mail Account.
Complete the Name, Address (email address), Password and Description fields.
Click Next.
Ensure IMAP is selected.
Enter the following incoming mail server information:
Incoming Mail (IMAP) Server - Requires SSL
Server: imap.mail.yahoo.com
Port: 993
Requires SSL: Yes
Hostname is mail.yahoo.com.
Username is your full email address
Password is the same password used to access webmail.
Enter the following outgoing mail server information:
Outgoing Mail (SMTP) Server - Requires SSL
Server: smtp.mail.yahoo.com
Port: 465 or 587
Requires SSL: Yes
Requires authentication: Yes
Username is your full email address
Password is the same password used to access webmail. It may have been entered for you.
Tap Next.
The iPhone will establish an SSL connection to your IMAP and SMTP servers.
That’s all!

System error: Default TXJCD is not filled in the table T001

Hi friends,
Can anyone help me out in this scenario? We are facing a peculiar problem.
We are in a upgrade project from 4.5b to ECC 6.0.Client is not maintaining any tax codes i.e they are maintaining it outside SAP.The problem is when ever the billing document is released to accounting(VF02) in ECC 6.0 it is showing this error System error: Default TXJCD is not filled in the table T001.But this is working fine in 4.5b.
Are there any basic changes regarding TAX JURISDICTION CODE is concerned from upgrade. Please provide.
Thanks in advance,
Yoga

Hi Yoga,
Probably, the program is showing error message FF799, please maintain transaction OBCL with a default tax jurisdiction code.
The tax jurisdiction code should be maintained at state level only and
corresponds to the tax jurisdiction code structure maintained in table
TTXD. For example, if your structure is 2-3-4-1. Then your default
code should be XX00000000. I suspect that the settings in transaction
OBCL are incorrect and hence the FF799 error, when shipping from a US
plant to a foreign ship-to customer (non-US).
Addional info concerning the Tax Interface for standard methods for
US taxes you can find at -   http://www.saplabs.com/projects/tax/
Documentation: Tax Interface Configuration Guide for release 4.6x
Please have a look at attached notes 112609 and 385127.
Here is the explaination that the process for tax-exempt transactions
has been changed.
Other notes you may need for OBCL :
-> 0627091   Message FF749 with billing data transfer
-> 0608159   Error FS791 during billing data transfer
-> 0380158   Jurisdiction code for export business transaction
-> 0419124   Export billing document with tax jurisdictions
I hope this information helps you,.
Regards,
Paulo

Why do I get the mesasge, default printer is not compatible with this version of photoshop elements

When I print from photoshop elements 13, I get the message, default printer is not compatible with this version of photoshop elements

Hi ,
Please update to PSE 13.1
13.1 has solved this problem.
Refer to this link.
Photoshop Elements Help | Printer errors with Photoshop Elements 13

WRV200 PPTP WAN - Default GW is not pointing to tunnel

Similar Messages

Maybe you are looking for