WRV200 - Problems with VPN Client and Internal network access

I have a WRV200 router and want to access the internal (Private Network) connected on the inside. I have successfully conected to the router with the Linksys VPN Client, but it does not appear to allow access to the internal network.
How do I enable NAT Transversal or Passthru? I have already selected all of the PPTP, L2TP and IPSEC Pass Through.
Has anyone gotten this to work?

I have actually gotten this to work. Issues surround this include the ability to get to the VPN if the main DNS is down (it does not fail over to the next DNS in the list).
If you unselect all of the boxes in the firewall General configuration, you can connect, but if you need to have all of this unchecked, what's the sense of having it?
Anyway, you can use the DoS Prevention, this is not interfering.
HTH.

Similar Messages

Problem with VPN Client and network access

We are running VPN client 4.0.1 on our laptops, and there are a number of users who are getting documents they are using on the internal network (off VPN) corrupted. The initial cause seemed to be the stateful firewall, but I have that turned off, and we are still getting it.
It only seems to be on the machines with VPN client installed, and it is only happening when the user is working on a file direct from the network drive. They are not connecting via the VPN client when the problem occurs.
any suggestions?
William.

Did you get any joy with this ? We seem to be having the same issue.
Thanks

Problem with VPN Client and PIX 7.0(5)

Hi, i have a problem configuring my pix 525 7.0(5) as a remote vpn server. I already configure the pix
sollowing this instructions (http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008060f25c.shtml)
and i can establish a vpn using CISCO VPN Client; but i can't reach any resource from my inside network or any network define in the PIX.
I think that could be a missing nat or an acl; but i have do a lot of research but i can figure out the solution.
This is the configuration i apply
access-list cryptomap-scada extended permit ip any 172.10.0.0 255.255.255.0
access-list acl-vpn-sap-remoto extended permit ip any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit icmp any 172.16.42.64 255.255.255.224
access-list acl-vpn-sap-remoto extended permit ip any any
access-list acl-vpn-sap-remoto extended permit icmp any any
ip local pool pool_vpn_sap 172.*.*.1-172.10.0.254 mask 255.255.255.0
nat (inside) 0 access-list cryptomap-scada
group-policy VPN_SAP_PED internal
group-policy VPN_SAP_PED attributes
vpn-filter value acl-vpn-sap-remoto
vpn-tunnel-protocol IPSec
username vpnuser password **** encrypted
username vpnuser attributes
vpn-group-policy VPN_SAP_PED
crypto ipsec transform-set vpn-cliente-remoto esp-3des esp-md5-hmac
crypto dynamic-map vpn-remoto-dymap 7 set transform-set vpn-cliente-remoto
crypto dynamic-map vpn-remoto-dymap 7 set reverse-route
crypto map siemens-scada-map 7 ipsec-isakmp dynamic vpn-remoto-dymap
isakmp policy 7 authentication pre-share
isakmp policy 7 encryption 3des
isakmp policy 7 hash sha
isakmp policy 7 group 2
isakmp policy 7 lifetime 43200
tunnel-group VPN_SAP_PED type ipsec-ra
tunnel-group VPN_SAP_PED general-attributes
address-pool pool_vpn_sap
default-group-policy VPN_SAP_PED
tunnel-group VPN_SAP_PED ipsec-attributes
pre-shared-key clavevpnsap
Thanks in Advanced

Hi, thanks for you response, if i remove the acl form de vpn filter, i get the same problem (i can't reach any host). This is the output from the command that you ask for.
PIX-Principal(config)# show running-config nat
nat (inside) 0 access-list cryptomap-scada
nat (inside) 9 JOsorioPC 255.255.255.255
nat (inside) 9 GColinaPC 255.255.255.255
nat (inside) 9 AlfonsoPC 255.255.255.255
nat (inside) 9 AngelPC 255.255.255.255
nat (inside) 9 JerryPC 255.255.255.255
nat (inside) 9 EstebanPC 255.255.255.255
nat (inside) 9 GiancarloPC 255.255.255.255
nat (inside) 9 WilliamsPC 255.255.255.255
nat (inside) 9 PerniaPC 255.255.255.255
nat (inside) 9 ElvisDomPC 255.255.255.255
nat (inside) 8 LBermudezPC 255.255.255.255
nat (inside) 9 HelpDeskPC 255.255.255.255
nat (inside) 9 OscarOPC 255.255.255.255
nat (inside) 9 AnaPC 255.255.255.255
nat (inside) 9 RobertoPC 255.255.255.255
nat (inside) 9 MarthaPC 255.255.255.255
nat (inside) 9 NOCPc5-I 255.255.255.255
nat (inside) 9 NOCPc6-I 255.255.255.255
nat (inside) 9 CiraPC 255.255.255.255
nat (inside) 9 JaimePC 255.255.255.255
nat (inside) 9 EugemarPC 255.255.255.255
nat (inside) 9 JosePC 255.255.255.255
nat (inside) 9 RixioPC 255.255.255.255
nat (inside) 9 DaniellePC 255.255.255.255
nat (inside) 9 NorimarPC 255.255.255.255
nat (inside) 9 NNavaPC 255.255.255.255
nat (inside) 8 ManriquePC 255.255.255.255
nat (inside) 8 MarcialPC 255.255.255.255
nat (inside) 8 JAlbornozPC 255.255.255.255
nat (inside) 9 GUrdanetaPC 255.255.255.255
nat (inside) 9 RVegaPC 255.255.255.255
nat (inside) 9 LLabarcaPC 255.255.255.255
nat (inside) 9 Torondoy-I 255.255.255.255
nat (inside) 9 Escuque-I 255.255.255.255
nat (inside) 9 Turbio-I 255.255.255.255
nat (inside) 9 JoseMora 255.255.255.255
nat (inside) 8 San-Juan-I 255.255.255.255
nat (inside) 8 Router7507 255.255.255.255
nat (inside) 8 NOCPc4-I 255.255.255.255
nat (InterfaceSAN) 8 MonitorHITACHI-I 255.255.255.255

Cisco ASA 8.3(1) with VPN Client and IP Communicator - one way communication

Hi Community.
I have a strange problem with my setup and I'm pretty sure it's either some type of routing (or NAT) or just a missing rule allowing the traffic. But I'm now at a point where I'd like to request your help.
I have some remote access users who have the Cisco IP Communicator (CIPC) installed on their notebooks. So:
VPN user with CIPC <> ASA Firewall <> Voice Router <> CCM <> IP Phone
The VPN works fine for any other traffic. Also the basic connection for the IP Communicator works fine. It get's connected to the CallManager, is shown as registered and you even can call an internal phone and also external phones. BUT: while you can hear the called party (so the internal phone) it doesn't work for the other way. There is no sound coming from the remote/caller.
I already figured out that it's also not possible to ping from the VPN phone to the internal IP Phone subnet. While the VPN user can ping any other device in the internal network, he can't do it to the Cisco IP Phones. But if the VPN phone calls a none-internal phone (mobiles...) - it works!
My thought is that the call can't be build up correctly between the VPN phone and the internal phone.
I found similiar situations with google but they are all for the other way around: call to internal works, but not to VPN.
What do you think?

Hi,
Typically ASA lists specific networks to the VPN Client when Split Tunnel is used.
This would mean that there is a Split Tunnel ACL used in the ASA configurations for this VPN connection which needs to have the missing network added for the traffic to be tunneled to the VPN connection.
- Jouni

How to configure full tunnel with VPN client and router?

I know the concept of split tunnel....Is it possibe to configure vpn client and router full tunnel or instead of router ASA? I know filter options in concentrators is teher options in ISR routers or ASA?

I think it is possible. Following links may help you
http://www.cisco.com/en/US/products/hw/routers/ps274/products_configuration_example09186a0080819289.shtml

Problem with VPN client on Cisco 1801

Hi,
I have configured a new router for a customer.
All works fine but i have a strange issue with the VPN client.
When i start the VPN the client don't close the connection, ask for password, start to negotiate security policy the show the not connected status.
This is the log form the VPN client:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1      14:37:59.133 04/08/13 Sev=Info/6          GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
2      14:38:01.321 04/08/13 Sev=Info/4          CM/0x63100002
Begin connection process
3      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100004
Establish secure connection
4      14:38:01.335 04/08/13 Sev=Info/4          CM/0x63100024
Attempt connection with server "asgardvpn.dyndns.info"
5      14:38:02.380 04/08/13 Sev=Info/6          IKE/0x6300003B
Attempting to establish a connection with 79.52.36.120.
6      14:38:02.384 04/08/13 Sev=Info/4          IKE/0x63000001
Starting IKE Phase 1 Negotiation
7      14:38:02.388 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 79.52.36.120
8      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700008
IPSec driver successfully started
9      14:38:02.396 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
10     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
11     14:38:02.460 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Unity), VID(dpd), VID(?), VID(Xauth), VID(Nat-T), KE, ID, NON, HASH, NAT-D, NAT-D) from 79.52.36.120
12     14:38:02.506 04/08/13 Sev=Info/6          GUI/0x63B00012
Authentication request attributes is 6h.
13     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer is a Cisco-Unity compliant peer
14     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DPD
15     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports DWR Code and DWR Text
16     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports XAUTH
17     14:38:02.460 04/08/13 Sev=Info/5          IKE/0x63000001
Peer supports NAT-T
18     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000001
IOS Vendor ID Contruction successful
19     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 79.52.36.120
20     14:38:02.465 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
21     14:38:02.465 04/08/13 Sev=Info/4          IKE/0x63000083
IKE Port in use - Local Port = 0xCEFD, Remote Port = 0x1194
22     14:38:02.465 04/08/13 Sev=Info/5          IKE/0x63000072
Automatic NAT Detection Status:
   Remote end is NOT behind a NAT device
   This   end IS behind a NAT device
23     14:38:02.465 04/08/13 Sev=Info/4          CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
24     14:38:02.502 04/08/13 Sev=Info/5          IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
25     14:38:02.502 04/08/13 Sev=Info/4          IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 79.52.36.120
26     14:38:02.502 04/08/13 Sev=Info/4          CM/0x63100015
Launch xAuth application
27     14:38:07.623 04/08/13 Sev=Info/4          CM/0x63100017
xAuth application returned
28     14:38:07.623 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 79.52.36.120
29     14:38:12.656 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
30     14:38:22.808 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
31     14:38:32.949 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
32     14:38:43.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
33     14:38:53.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
34     14:39:03.371 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
35     14:39:13.514 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
36     14:39:23.652 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
37     14:39:33.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
38     14:39:43.948 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
39     14:39:54.088 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
40     14:40:04.233 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
41     14:40:14.384 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
42     14:40:24.510 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
43     14:40:34.666 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
44     14:40:44.807 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
45     14:40:54.947 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
46     14:41:05.090 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
47     14:41:15.230 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
48     14:41:25.370 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
49     14:41:35.524 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
50     14:41:45.665 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
51     14:41:55.805 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
52     14:42:05.951 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
53     14:42:16.089 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
54     14:42:26.228 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
55     14:42:36.383 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
56     14:42:46.523 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
57     14:42:56.664 04/08/13 Sev=Info/6          IKE/0x63000055
Sent a keepalive on the IPSec SA
58     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
59     14:43:02.748 04/08/13 Sev=Info/4          IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DWR) to 79.52.36.120
60     14:43:03.248 04/08/13 Sev=Info/4          IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
61     14:43:03.248 04/08/13 Sev=Info/4          CM/0x63100014
Unable to establish Phase 1 SA with server "asgardvpn.dyndns.info" because of "DEL_REASON_CANNOT_AUTH"
62     14:43:03.248 04/08/13 Sev=Info/5          CM/0x63100025
Initializing CVPNDrv
63     14:43:03.262 04/08/13 Sev=Info/6          CM/0x63100046
Set tunnel established flag in registry to 0.
64     14:43:03.262 04/08/13 Sev=Info/4          IKE/0x63000001
IKE received signal to terminate VPN connection
65     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
66     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
67     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x63700014
Deleted all keys
68     14:43:03.265 04/08/13 Sev=Info/4          IPSEC/0x6370000A
IPSec driver successfully stopped
And this is the conf from the 1801:
hostname xxx
boot-start-marker
boot-end-marker
enable secret 5 xxx
aaa new-model
aaa authentication login xauthlist local
aaa authorization network groupauthor local
aaa session-id common
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.0.1.1 10.0.1.10
ip dhcp excluded-address 10.0.1.60 10.0.1.200
ip dhcp excluded-address 10.0.1.225
ip dhcp excluded-address 10.0.1.250
ip dhcp pool LAN
   network 10.0.1.0 255.255.255.0
   default-router 10.0.1.10
   dns-server 10.0.1.200 8.8.8.8
   domain-name xxx
   lease infinite
ip name-server 10.0.1.200
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip inspect log drop-pkt
ip inspect name Firewall cuseeme
ip inspect name Firewall dns
ip inspect name Firewall ftp
ip inspect name Firewall h323
ip inspect name Firewall icmp
ip inspect name Firewall imap
ip inspect name Firewall pop3
ip inspect name Firewall rcmd
ip inspect name Firewall realaudio
ip inspect name Firewall rtsp
ip inspect name Firewall esmtp
ip inspect name Firewall sqlnet
ip inspect name Firewall streamworks
ip inspect name Firewall tftp
ip inspect name Firewall vdolive
ip inspect name Firewall udp
ip inspect name Firewall tcp
ip inspect name Firewall https
ip inspect name Firewall http
multilink bundle-name authenticated
username xxx password 0 xxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group xxx
key xxx
dns 10.0.1.200
wins 10.0.1.200
domain xxx
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-sha-hmac
crypto ipsec transform-set xauthtransform esp-des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode adsl2+
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
ip address 10.0.1.10 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp pap sent-username aliceadsl password 0 aliceadsl
crypto map clientmap
ip local pool ippool 10.16.20.1 10.16.20.200
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 0.0.0.0 0.0.0.0 10.0.1.2
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static udp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source static udp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source list 101 interface Dialer0 overload
access-list 101 remark *** ACL nonat ***
access-list 101 deny   ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
access-list 101 permit ip 10.0.1.0 0.0.0.255 any
access-list 150 remark *** ACL split tunnel ***
access-list 150 permit ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
control-plane
line con 0
no modem enable
line aux 0
line vty 0 4
password xxx
scheduler max-task-time 5000
end
Anyone can help me ?
Sometimes the vpn can be vreated using the iPhone or iPad vpn client...

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problem with VPN Client passthrough on ASA 5505

I am having a problem with passing through a VPN client connection on an ASA 5505. The ASA is running version 8 and terminates an anyconnect VPN. The ASA is using PAT. When the inside user connects with the VPN client, it connects but no traffic passes through the tunnel. I see the error
305006 regular translation creation failed for protocol 50 src INSIDE:y.y.y.y dst OUTSIDE:x.x.x.x
UDP 500,4500 and ESP are allowed into the ASA. Ipsec inspection has also been setup on a global policy, but the user still cannot pass traffice to the remote VPN he is connected through.
At the Main Office we have an ASA 5510 that terminates a site to site VPN, allows remote connections with PAT and allows passthrough no problems. Any ideas?

I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP?

Problems with VPN-Client 5.0 instoled on Windows Vista over ADSL Conecction

Hi, I have severals clients that they use Windows Vista and connects throw there lan over a VPN-Client. The clients that has an ADSL connection in there hose has disconect problems. Do you know why?? Do you know same workarround to do?? Thanks.
Regards.

Make sure that you have the right cable pinout and that your ISP has turned on the DSL service. Troubleshoot the DSL connection by watching the modem state of the ADSL interface as the line retrains.
To use the VPN Client, you need
- Direct network connection (cable or DSL modem and network adapter/interface card), or
- Internal or external modem
For further more troubleshoot click this link,
http://www.cisco.com/en/US/docs/security/vpn_client/cisco_vpn_client/vpn_client500_501/release/notes/51client.html#wp1550392

Problem with data table and internal and external command button

thanks for your time,
i have this problem
<t:dataTable binding="#{manejadorAsociarEvaluadoresProyecto.tablaPosiblesEvaluadores}"
cellpadding = "6"
cellspacing = "3"
value = "#{manejadorAsociarEvaluadoresProyecto.listaPosiblesEvaluadores}"
var = "posibleEvaluador"
preserveDataModel="false">
<h:inputTextarea value="#{posibleEvaluador.correoActualCuerpo}"
cols="50"
rows="50"
rendered="#{posibleEvaluador.detalle}" />
<h:commandLink immediate="false" action="#{posibleEvaluador.editar}" value="Editar Correo"/>
</t:dataTable>
<h:panelGroup id="panelBotonEvaluadores" rendered="#{!manejadorAsociarEvaluadoresProyecto.b_mostrarEvaluadores && manejadorAsociarEvaluadoresProyecto.tieneProyectos}">
<h:commandButton action="#{manejadorAsociarEvaluadoresProyecto.mostrarEvaluadores}"
value="Asociar evaluadores"/>
</h:panelGroup>
this is the method of posibleEvaluador
public String editar()
setDetalle(!getDetalle());
return "";
all run perfect, until y click in "asociar evaluadores" button, after of this the commandLink "editar Correo" not run, this commanlLink is for not show the inputTextArea, i don't know what happend.
thanks for your help

Hello,
I have replicated and confirmed the problem with LabVIEW 2010, Report Generation Toolkit 2010 and Word 2010. I have filed this to R&D under CAR ID #257414. As a workaround you can manually set each cell using Word Edit Cell.vi. I have attached a simplified representation of this unexpected behavior as well as the workaround. Hopefully this helps everyone out!
David_L | Certified LabVIEW Architect
LabVIEW Tools Network | LabVIEW Tools Network Developer Center
Attachments:
Word 2010 Table CAR.vi ‏17 KB
Word 2010 Table FIX.vi ‏22 KB

Problems with Installing iTunes and wireless network connection

Every time I attempt to install iTunes it completely kicks the internet off and an error comes up that the wireless network adapter to not connect or is not detected. My internet service is connected to a router which I receive wirelessly to my laptop. I do not understand why it is happening and to get the internet to work again I needed to do a system restore. Any ideas why this is happening. Also when iTunes was installed it came up correctly, it would just not connect to the net. I have had a previous version on my old laptop but since purchasing this new laptop I am having such difficulty. On another note, if this problem can be resolved, once iTunes is working is there a way to get the songs from my old computer onto the new? Thanks for the help in advance!

I just saw your post and I resolved this on mine for my wired connection. I'm willing to bet that the issue is the same for wireless. Here's what I found.
Issue:
During the installation, iTunes installs some network components related to mobile device support over ethernet(Apple Mobile Device Ethernet Service - netaapl.inf). At the same time, according the logs, the install process removed OEM18.inf. This almost exactly coincided with the time that I saw the network connection die (preceded it by a few seconds).
Basically, iTunes appears to be removing a required network component.
Resolution:
After installing iTunes and the network connection breaking, remove the network device from Device Manager and allow Windows to reinstall it automatically.
The following instructions are for Windows 7, but they are close enough to follow for other versions of Windows.
1. Click the Start button (Jewel in Vista and Win7).
2. Right-click Computer and click Manage in the menu that appears (type your password or click Yes if prompted).
3. On the left side of hte Computer Management window, click Device Manager.
4. Click the arrow (or plus sign) next to Network Adapters to expand that section.
5. Right-click your network adapter and click Uninstall in the menu that appears.
6. Click OK.
7. Reboot.
Windows should automatically detect and reinstall your network device on boot.

Problems with mail, messags, and social network accounts

Hi,
first of all, sorry for my bad English.
I would like to know if there is a maximum limit of accounts (email, social network, etc. etc.) that OS10 can handle.
On my Passport (OS10 Version 10.3.0.675) I have the following:
- 1 BBM
- 1 WhatsApp
- 1 Facebook
- 12 Mail
Now, when I try to insert another account (for example mail or Twitter), I recived the following error message:
"The maxximum accounts has been reached".
Is that right?
With the Z10 and the Q10, if I remember correctly, I did not have this problem.
I need to add more email accounts, someone can help me?
Thank you all.
I'M NOT LAZY,
I JUST DON'T GIVE NOTHING!

Let me see what I can find out and I'll get back to you when I know more! Thanks
Did someone help you? Click Like! Did a post solve your issue? Click Accept as Solution!
Follow me on Twitter or Google+ and subscribe to the Inside BlackBerry Help Blog

Connection problems with idea pad and public network

My Lenovo Idea Pad connects fine at home on our ATT internet connectoin, but will not connect to a local public network at a local departent store. Anyone having suggestions email me at xxxxxxxxxxxxxx Thank you!\
Richard
Moderator note; e-mail address removed to stop the spambots getting it

I just saw your post and I resolved this on mine for my wired connection. I'm willing to bet that the issue is the same for wireless. Here's what I found.
Issue:
During the installation, iTunes installs some network components related to mobile device support over ethernet(Apple Mobile Device Ethernet Service - netaapl.inf). At the same time, according the logs, the install process removed OEM18.inf. This almost exactly coincided with the time that I saw the network connection die (preceded it by a few seconds).
Basically, iTunes appears to be removing a required network component.
Resolution:
After installing iTunes and the network connection breaking, remove the network device from Device Manager and allow Windows to reinstall it automatically.
The following instructions are for Windows 7, but they are close enough to follow for other versions of Windows.
1. Click the Start button (Jewel in Vista and Win7).
2. Right-click Computer and click Manage in the menu that appears (type your password or click Yes if prompted).
3. On the left side of hte Computer Management window, click Device Manager.
4. Click the arrow (or plus sign) next to Network Adapters to expand that section.
5. Right-click your network adapter and click Uninstall in the menu that appears.
6. Click OK.
7. Reboot.
Windows should automatically detect and reinstall your network device on boot.

Problems with SRW224G4 switch and Bridged Network Cards

Hello,
We have recently installed a SRW224G4 switch and have discovered that when we plug our DELL PowerEdge 2900 server into the switch, the switch loses all network connectivity and all of the LED's on the switch start flashing.
The server works perfectly well plugged into another switch, but as soon as we introduce the SRW224G4 into the network, either with the server plugged into that switch or any other, the problem re-occurs.
The only way we found we could eliminate this issue was if we disabled the Bridged Network connection on the two network cards on the server. If we do that, everything is fine, except the network performance of the server has dropped significantly.
The server is plugged into the 1GB ports on the switch, although we tried it on the 100MB ports and received the same problems. The switch reports that the ports are running at full-duplex.
Has anyone noticed this behavior before, and more importantly been able to rectify it.
Thanks in advance for your assistance,
Paul

I had this problem as well with any Linksys 2024 or rackmountable switch.. The trick is, you need to use the network cards management software to "team" or bridged the 2 NIC's otherwise the switch detects a loop and the whole thing locks up. So lame... Windows built in bridge mode stinks dont use it. When you use the Intel management software or Dell or HP's NIc management software you have the option to actually choose "redundant mode" where you can pick a Nic to be the primary, or you can choose Load Balancing where you can essentially double your throughput by joining the 2 nics.
In Windows 2008 Server, you actually do this by going to the Properties on the NIC in Device Manger. the software controls are now built right into the driver. pretty neat. 2003 you can check Device Manager the same way but not sure if it's the same as 2008, you might need to run the actual NIC management app.
Hope this helps
fdigi

Problem with ios 6 and cellular-network connection

Hi! I've youst updated my iphone 4 to ios 6 and now it cant't establish a connection to the cellular-network. Is there anybody who knows why and what to do? Thanks!

did you have nay luck with this? same happened to my wifes 4s. Apple reset it and the next day it lost cell service again.

Problem with R2 signalling and satelite network

Hi,
Is someone have experience with voice satelite networks and R2 signaling.
Regards

Have you selected R2-pulse.
R2-PulseR2 line signaling type ITU-U Supplement 7, typically used for systems that employ satellite links (where a Tone/A bit is pulsed).
try command -- proceed-to-send
ITU pulsed line signaling (S-7) ACKs the seizure with a proceed-to-send signal (150 ms pulse). A variant of this signaling over satellite links does not use this signal. If this is configured, the router does not ACK the seizure for incoming calls and does not expect ACK for outgoing calls. This affects pulsed line signaling calls only. Not supported on AS5800 yet.
http://www.cisco.com/en/US/tech/tk652/tk653/technologies_tech_note09186a00800942f2.shtml

WRV200 - Problems with VPN Client and Internal network access

Similar Messages

Maybe you are looking for