WRV54G - error loading firmware upgrade (v2.392)

I went to upgrade the firmware on my WRV54G -
Downloaded the latest firmware -- v2.392 (5MB file - name WRV54G_R2_39_2_02082006)
In the router - I go to the Administration / Config Mgmt page - and tried to load the firmware upgrade and I get a blank browser screen with the following error message
'413 Request Entity Too Large'
'The length is too large'
Has someone also found this? Is there a simple fix?

Hi… I think there was some error while downloading this file. Try downloading it again. Reset this router for 1 min and try to upgrade the firmware again. Let me know if you can upgrade it.

Similar Messages

  • HP DesignJet 5500uv system error at FirmWare upgrade 0f0100 0001d06

    Hi There,  After I replaced a failure hard drive, and updagrded the firmware, I want to upload media profile, my plotter keeps coming up a system error with code and warning: "0f0100 00001d06 Switch off/on, If problem consists, contact HP support". I did many times of switch off and on, it still keeps say that, I cannot go any further. One thing I can say that current hard drive (capacity 80gb) is a little bit larger that  the broken one(40gb), and not a brand new. The firmware used is S.56.07. Another issue is that "LM printhead needs to be reseat" many times as well (after many tries just marginally passed that issue). Any one has any idea I can fix this or solve the problem, I spent many days on this, really frustrated. Thanks a lot for any input. Binke   

    Hi There,  Thanks a lot for your prompt input. Your assumption sounds right. The error just occurs right when I try to open the WebAccess page (or a couple of seconds). With your remind, I got the HP download manager A.04.30, found my card 615n/J6057A, with a current firmware R.24.06, can upgraded to R.25.57. But the result said in detail: "Corrupted Firmware file". Does that mean the R.25.57 was corrupted, or R.24.06? or other part of the .upg firmware? What can I do with this, try a newer HP download manager (if available)? thanks for your help again. Binke

  • Ideatab a3000 dead after error during firmware upgrade using flash tool

    i was upgrading to firmware version 4.2.2 with call option then i got an error message and the tablet is dead 
    any so;utions

    Dear uliwooly,
    I have tried in different PC, different version of flastool and different .tft file but all are failed!
    One thing i should share:
    My phone can connect to flash-mode without pressing volume down key!
    Plz reply....

  • NMH410 Firmware Upgrading Error

    Hello everyone,
    I recently upgraded the HDDs on my NMH410 and basically it resets everything and even roles back the firmware.
    But this time around I couldn't manage make it upgrade. Everytime I receive this error message:
    "Error - Result"
    Firmware Upgrade has encountered an error. Upgrade Aborted!
    There is a thread on this forum suggesting to change the DNS Server but it didn't work for me either.
    What to do? Anyone having or had similar issues? Is it something from the Cisco's side?
    Is there a way to sideload the firmware or force to install it by directly accessing the hub?

    Here's an article that might help you: http://kb.linksys.com/Linksys/ukp.aspx?pid=80&app=vw&vw=1&login=1&json=1&docid=ec5f31fe7f0f4a8c9a89a...

  • Zen Micro 5GB Firmware "Upgrade Faile

    Zen MicroFirmware: 2..02?Have just bought it from america, have tried installing both firmwares from the site, and both of them say "Upgrade Failed!" I havent installed any of the software from the disc except the Zen Micro driver, my pc didnt need this but i thought it would be best to. Also i can only add tracks to it through WMP 0, i cant drap and drop in windows explorer, why is this? On my old creative muvo n200 i could do this fine!?Some help please. Do i need to erase the firware in the recovery menu? I am just running the downloaded applications when my player has the docked icon on the screen.
    Message Edited by ajay6 on 03-5-200607:28 PM

    Thanks for help.
    Major problem solved.
    Already upgraded to new firmware.
    I do it by:
    1. uninstall all creative application and plugin.
    2. using registry cleaner to clean the registry.
    3. downgrade WMP to WMP0
    4. Detected by WMP as MTP device, loading firmware upgrade, closed WMP. upgraded.
    Now it Working fine already, just still have some problem is:
    . Only WMP can detect it, all creative application can't detect it..
    thanks anyway.

  • After upgrade to 4.1 from 3.2, admin logon page error with "done error load

    Hello all,
    Just upgraded 3.2 to 4.1. ran @apexins.sql sysaux sysaux temp /i/. Installation was successful and upgrade completed with no errors. When trying to log on to admin page, url changes to admin workarea but with IE we get "done error loading pages" and logon screen doesn't appear. All objects are compiled, accounts are unlocked and valid. Same thing happens when attempting to logon to the applicaiton. Any help would be appreciated. Open SR with oracle support, but no reply since yesterday.
    inital url: https://xxxxxxxx.xxx.com:8443/pls/apex/apex_admin
    ending url: https://xxxxxxxx.xxx.com:8443/pls/apex/f?p=4550:10:903647939084101
    "done error loading pages"
    Edited by: user12128153 on May 18, 2012 2:21 AM

    Hi user12128153 (a real name would be nice),
    a few questions for you.
    Do you experience the same errors with firefox? If so install firebug (if you don't have it already) and see if the errors have to do with missing css etc.
    What application server do you use, OHS/Apex Listener etc?
    Kofi

  • 11.5.10.2 to R12.1.1 upgrade: Error loading seed data for GL_DEFAS_ACCESS_SETS:  DEFINITION_ACCESS_SET = SUPER_USER_DEFAS,  ORA-06508: PL/SQL: could not find program unit being called

    Hello,
    EBS version : 11.5.10.2
    DB version : 11.2.0.3
    OS version : AIX 6.1
    As a part of 11.5.10.2 to R12.1.1 upgrade, while applying merged 12.1.1 upgrade driver(u6678700.drv), we got below error :
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    ATTENTION: All workers either have failed or are waiting:
               FAILED: file glsupdas.ldt on worker  3.
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    drix10:/fmstop/r12apps/apps/apps_st/appl/admin/FMSTEST/log>tail -20 adwork003.log
    Restarting job that failed and was fixed.
    Time when worker restarted job: Wed Aug 07 2013 10:36:14
    Loading data using  FNDLOAD function.
    FNDLOAD APPS/***** 0 Y UPLOAD @SQLGL:patch/115/import/glnlsdas.lct @SQLGL:patch/115/import/US/glsupdas.ldt -
    Connecting to APPS......Connected successfully.
    Calling FNDLOAD function.
    Returned from FNDLOAD function.
    Log file: /fmstop/r12apps/apps/apps_st/appl/admin/FMSTEST/log/US_glsupdas_ldt.log
    Error calling FNDLOAD function.
    Time when worker failed: Wed Aug 07 2013 10:36:14
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
    drix10:/fmstop/r12apps/apps/apps_st/appl/admin/FMSTEST/log>tail -20 US_glsupdas_ldt.log
    Current system time is Wed Aug  7 10:36:14 2013
    Uploading from the data file /fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/import/US/glsupdas.ldt
    Altering database NLS_LANGUAGE environment to AMERICAN
    Dumping from LCT/LDT files (/fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/import/glnlsdas.lct(120.0), /fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/import/US/glsupdas.ldt) to staging tables
    Dumping LCT file /fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/import/glnlsdas.lct(120.0) into FND_SEED_STAGE_CONFIG
    Dumping LDT file /fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/import/US/glsupdas.ldt into FND_SEED_STAGE_ENTITY
    Dumped the batch (GL_DEFAS_ACCESS_SETS SUPER_USER_DEFAS , GL_DEFAS_ACCESS_SETS SUPER_USER_DEFAS ) into FND_SEED_STAGE_ENTITY
    Uploading from staging tables
      Error loading seed data for GL_DEFAS_ACCESS_SETS:  DEFINITION_ACCESS_SET = SUPER_USER_DEFAS,  ORA-06508: PL/SQL: could not find program unit being called
    Concurrent request completed
    Current system time is Wed Aug  7 10:36:14 2013
    ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++

    Below is info about file versions and INVALID packages related to GL.
    PACKAGE BODY GL_DEFAS_ACCESS_SETS_PKG is invalid with error component 'GL_DEFAS_DBNAME_S' must be declared.
    I can see GL_DEFAS_DBNAME_S is a VALID sequence accessible by apps user with or without specifying GL as owner.
    SQL> select text from dba_source where name in ('GL_DEFAS_ACCESS_DETAILS_PKG','GL_DEFAS_ACCESS_SETS_PKG') and line=2;
     TEXT
    /* $Header: glistdds.pls 120.4 2005/05/05 01:23:16 kvora ship $ */
    /* $Header: glistddb.pls 120.16 2006/04/10 21:28:48 cma ship $ */
    /* $Header: glistdas.pls 120.4 2005/05/05 01:23:02 kvora ship $ */
    /* $Header: glistdab.pls 120.5 2006/03/13 19:56:21 cma ship $ */ 
    SQL> select * from all_objects where object_name in ('GL_DEFAS_ACCESS_DETAILS_PKG','GL_DEFAS_ACCESS_SETS_PKG')
      2 ; OWNER OBJECT_NAME SUBOBJECT_NAM OBJECT_ID DATA_OBJECT_ID OBJECT_TYPE CREATED LAST_DDL_TIME TIMESTAMP STATUS T G S NAMESPACE
    EDITION_NAME
    APPS GL_DEFAS_ACCESS_DETAILS_PKG 1118545 PACKAGE 05-AUG-13 05-AUG-13 2013-08-05:18:54:51 VALID N N N 1 
    APPS GL_DEFAS_ACCESS_SETS_PKG 1118548 PACKAGE 05-AUG-13 06-AUG-13 2013-08-05:18:54:51 VALID N N N 1 
    APPS GL_DEFAS_ACCESS_SETS_PKG 1128507 PACKAGE BODY 05-AUG-13 06-AUG-13 2013-08-06:12:56:50 INVALID N N N 2 
    APPS GL_DEFAS_ACCESS_DETAILS_PKG 1128508 PACKAGE BODY 05-AUG-13 05-AUG-13 2013-08-05:19:43:51 VALID N N N 2 
    SQL> select * from all_objects where object_name='GL_DEFAS_DBNAME_S'; OWNER OBJECT_NAME SUBOBJECT_NAM OBJECT_ID DATA_OBJECT_ID OBJECT_TYPE CREATED LAST_DDL_TIME TIMESTAMP STATUS T G S NAMESPACE
    EDITION_NAME
    GL GL_DEFAS_DBNAME_S 1087285 SEQUENCE 05-AUG-13 05-AUG-13 2013-08-05:17:34:43 VALIDN N N 1 
    APPS GL_DEFAS_DBNAME_S 1087299 SYNONYM 05-AUG-13 05-AUG-13 2013-08-05:17:34:43 VALIDN N N 1 
    SQL> conn apps/apps
    Connected.
    SQL> SELECT OWNER, OBJECT_NAME, OBJECT_TYPE, STATUS
    FROM DBA_OBJECTS
    WHERE OBJECT_NAME = 'GL_DEFAS_ACCESS_SETS_PKG'; 2 3 OWNER OBJECT_NAME OBJECT_TYPE STATUS
    APPS GL_DEFAS_ACCESS_SETS_PKG PACKAGE VALID
    APPS GL_DEFAS_ACCESS_SETS_PKG PACKAGE BODY INVALID SQL> ALTER PACKAGE GL_DEFAS_ACCESS_SETS_PKG COMPILE; Warning: Package altered with compilation errors. SQL> show error
    No errors.
    SQL> ALTER PACKAGE GL_DEFAS_ACCESS_SETS_PKG COMPILE BODY; Warning: Package Body altered with compilation errors. SQL> show error
    Errors for PACKAGE BODY GL_DEFAS_ACCESS_SETS_PKG: LINE/COL ERROR
    39/17 PLS-00302: component 'GL_DEFAS_DBNAME_S' must be declared 
    drix10:/fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/odf>cat $GL_TOP/patch/115/sql/glistdab.pls|grep -n GL_DEFAS_DBNAME_S
    68: SELECT GL.GL_DEFAS_DBNAME_S.NEXTVAL
    81: fnd_message.set_token('SEQUENCE', 'GL_DEFAS_DBNAME_S');
    SQL> show user
    USER is "APPS"
    SQL> SELECT GL.GL_DEFAS_DBNAME_S.NEXTVAL
      FROM dual; 2                         -- with GL.
      NEXTVAL
      1002
    SQL> SELECT GL_DEFAS_DBNAME_S.NEXTVAL from dual;               --without GL. or using synonym.
      NEXTVAL
      1003
    drix10:/fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/odf>strings -a $GL_TOP/patch/115/sql/glistdab.pls|grep '$Header'
    REM | $Header: glistdab.pls 120.5 2006/03/13 19:56:21 cma ship $ |
    /* $Header: glistdab.pls 120.5 2006/03/13 19:56:21 cma ship $ */
    drix10:/fmstop/r12apps/apps/apps_st/appl/gl/12.0.0/patch/115/odf>strings -a $GL_TOP/patch/115/sql/glistdas.pls |grep '$Header'
    REM | $Header: glistdas.pls 120.4 2005/05/05 01:23:02 kvora ship $ |
    /* $Header: glistdas.pls 120.4 2005/05/05 01:23:02 kvora ship $ */

  • Help..I updated my iphone4 to iOS to 7.1.1 from 6.1.3 at last stage of firmware upgrading throwing an error 16 and stuck in recovery mode.

    HIAll
    I waited so long not to update of my iphone4 to 7.x.x because of bugs and not much stable for iPhone4 and many reviews from friends saying phone is very slow and many bugs but after release of iOS 7.1.1 of many improvements for iphone4. I tried to update my iphone4 to 7.1.1 through iTunes at last stage of firmware upgrading its showing an error occurred error (16). I checked in internet error16 is purely hardware issue before my phone is very good condition in iOS6.1.3 no problem with my phone, But after upgrading to how it will be hardware issues. why Apple engineers are not testing properly their software’s before releasing great updates to customers now my phone is out of warranty and I can’t use it anymore just showing iTunes symbol and charger on the screen while on/off showing apple logo. From the past September there is no proper solution for error 16. Don’t know  what these people are doing about that error why apple is crashing customer phones by releasing useless update to phones what is the point of buying such a expensive phones don't know what to do with this phone. Tried many possible ways
    Tried: presing home+power button at 95% of  firmware update
              Disconnected battery and restored
              used DrPhone to restart
              tried to restore old version 7.x.x
              no luck.
              used new original cables
              restored with Macbook
              tried to restore in 3 Different computers and so many times but  no luck

    Hi, to get your iPhone  4 back to normal, here're two ways for you.
    1.  Use Dr.Fone for iOS. The free trial version can fix iPhone screen of death. The free trial version can do that, you don't have to pay.
    Just download and install this software on your computer and connect your iPhone 4 to computer with a USB cable. When it detects your iPhone 4 is abnormal, click Restart the device to get your iPhone 4 to be normal.
    2. Use iTunes to fix it.
    Step 1. Make sure that the latest iTunes is installed on your computer.
    Step 2. Plug into a USB cable to connect your iPhone4 to computer.
    Step 3. Press and hold the Home button and the Sleep/Wake button at the same time for about 10s.
    Step 4. 10 seconds later, release the sleep/wake button. But continue to hold the home button until a message comes out, saying "iTunes has discovered an iPhone 4 in recovery mode, you must restore this iPhone before it can be used with iTunes".
    Step 5. Click your iPhone 4 in the left sidebar to show the device control panel on the right. Then, click Summary.
    Step 6. Go to Backups section and click Restore Backup.... In the drop-down list, choose a backup file and restore to your iPhone 4

  • Zen Micro PlaysForSure firmware upgrade fatal error - RESOL

    First, sorry about poor english!
    When i tried to upgrade my Zen Micro to the latest firmware i got the following message: "Creative Zen Micro PlaysForSure Firmware Upgrade: This application only supports Windows XP platform with at least Service Pack installed." The executable name was: ZenMicroP4S_PCFW_L6_2_2_02.exe and yes i have Windows XP SP2 installed on my computer. (and on the other three computers, where i got the exact error message.)Message Edited by kaszast on 0-26-2006 08:37 AM

    Dear Creative!
    You screwed the upgrade program a bit, because it is works ONLY IN ENGLISH version on Windows XP. Shame! You are pushing me into the sea of warez...

  • Firmware upgrade crippled cp1025nw

    LaserJet CP1025nw color: was working flawlessly
    received email from HP 4/3/2012, recommending firmware upgrade to v 20120130.
    ran upgrade 4/3/2012 from iMac, OS10.6.8.
    got error: 'update failed'
    print queue says 'printing', cp1025nw doesn't respond.
    printer lights:  orange triangle enclosed exclamation mark plus green semicircle 
      This means: fatal error, per the user manual.  
       manual instructs to turn off, unplug, plug-in, turn on.  I did this several times.
    printer lights still indicate: fatal error.
    HP utility says: device status: unknown, service ID: unknown, FW version: unknown, driver version 2.0.20110727
                      tried to print configuration page: got error 'cannot establish two-way communication with the device'
                      printer and computer are connected with USB cable,  (this cable / port communicates without issue to Epson inkjet printer)
    Tried printing from Dell laptop: Latitude E6410 with USB cable: Windows XP professional, 2002, service pack 3.
                      has routinely printed from this computer previously.
    error message in printer queue: 'error - printing', 
    Dell said 'found new hardware'  tried to install with HP cd-rom
                      error message said 'the hardware was not installed because the wizard cannot find the necessary software'
    ran the HP print diagnostic utility HPPDU.exe file from the Dell with USB cable: 'Everything checks out okay with your printer'
     print test page: no response from the cp1025nw
    What should I try next?

    Since my last post I’ve retried the same troubleshooting described before, this time just from the PC.  The result is still the same.  Lights on the cp1025nw indicate “fatal error”.
    Does anyone know how to put this printer into ‘bootcode’ mode?  I’ve read about this in some other posts about HP firmware updates trashing printers.
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=110&prodSeriesId=...
    and
    http://www.fixyourownprinter.com/forums/laser/63535
    Is there some combination of button presses that sends the printer into bootcode so it is ready to accept the firmware?
    HP:  How do you start up these printers when they are just manufactured to load the firmware?

  • X4600m2 bios/ilom firmware upgrade problem

    In the X4600m2 downloads, under Software 2.3, in the firmware category, I downloaded ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima (md5 checks out). I can't install the new firmware however (using the ILOM cli):
    -> load -source tftp://172.22.95.215/ILOM-3_0_3_31_r42822-Sun_Fire_X4600M2.ima
    NOTE: A firmware upgrade will cause the server and ILOM to
          be reset. It is recommended that a clean shutdown of
          the server be done prior to the upgrade procedure.
          An upgrade takes about 6 minutes to complete. ILOM
          will enter a special mode to load new firmware. No
          other tasks can be performed in ILOM until the
          firmware upgrade is complete and ILOM is reset.
    Are you sure you want to load the specified file (y/n)? y
    Do you want to preserve the configuration (y/n)? n
    Image is not for this platform.
    Firmware image update failed.
    ->With all previous releases this worked fine.
    Update: the upgrade on the ILOM web interface also fails.
    I'm running this version currently:
    -> version
    SP firmware 2.0.2.10
    SP firmware build number: 38791
    SP firmware date: Tue Nov 4 18:36:42 PST 2008
    SP filesystem version: 0.1.14
    Any idea why this is failing? I've tried both preserving and not preserving the configuration.
    Edited by: kaufmann on Jul 22, 2009 9:27 AM

    Quote from: renewest on 14-July-12, 19:43:52
    Are you saying that it worked before because of an error? I've worked with boards before tha supported 2 monitors, 1 on the mainboard and 1 on a graphics card.
    Quote from: renewest on 14-July-12, 19:43:52
    Are you saying that it worked before because of an error?
    Yes.. normally onboard become automatically disabled, when dedicated card is installed.

  • BDX2300 firmware upgrade fail (USB)

    I have had mulltiple screen freezes on most Bluray discs I have tried. I see there is a firmware upgrade 1.15 to stabalize, but...
    I have followed the instructions for copying the files for firmware upgrade to USB drive in Directory UPG_ALL. When I plug the USB drive into the player, I see the USB icon loading, but the player does not try to load the firmware as the instruction states:
    3)
    “Insert the USB Thumb Drive with the firmware” copied to the drive into the USP port located on the front. (Note: Some models may have the USB port located behind a protective cover or on the rear of the unit)
    4)
    After a few seconds the update screen will appear. The unit will automatically update the firmware in sequence as shown in Figure 1a through 1d.
    If I go to Setting, system, and try to upgrade from USB, I get a messsage that the file is not found. I have verified the files are in the directory as requested.
    What are the correct instructions that will allow me to update my firmware via USB?

    I just successfully upgrade my brother's machine thanks to this forum:
    Here is what worked for me with upgrade V1.22. after much trial and error: (Your folders will have your version in the name)
    Unzip the downloaded zip file. There is a real nice PDF file that tells you exactly how to do it. THROW IT OUT!
    On a clean thumb drive (don't worry about  BUDA and System Volume information) create a folder named  UPG_ALL.
    When you unzip your file you will find, besides the PDF file you should dispose of, a folder named V1.22. In that folder you will find yet another folder named V1.22.
    In that folder you will find some files: I had the following in mine:
    8551_linux_demo_dbg.bin
    8551_linux_demo_dbg_id.bin
    DVD.bin
    dvd_id.bin
    mt8551_bl_linux.bin
     Copy those files to the UPG_ALL folder on the Thumb drive.
    Now some of you may have gotten this far before, what they didn't tell us was that you can tell the player to look on the USB port.
    With thumb drive inserted and the power on select the icon on the tv screen with the gears. Then select SETTINGS and  then select UPDATE.
    You should now see a choice  for disk - USB - or network (or something like that)
    Select USB and wallah you should have an update occur.
    This last part was strictly from memory, because I couldn't interupt the movie my brother  was watching.
    I hope this helps,
    Jerry

  • RVS4000 firmware upgrade to ver 2.0.3.2

             Hello,
    I have firmware version 2.0.2.7. I've down loaded the firmware upgrade utility ver 1.3, and do not see a read me or help file.  I've disconnected the cables as directed, but recive a 'broadcast error' and a 'browse device error'      What is causing this?
    Curtis

    Hi Curtis, the firmware upgrade should be done through the GUI of the RVS4000. If you're able to log in to the device, the upgrade is under admin -> firmware upgrade, then just browse the file and upload it.
    -Tom
    Please mark answered for helpful posts

  • WRT54G ver.6 no WLAN after firmware upgrade

    I just did a manual firmware upgrade for the router (WRT54Gv6 v1.02.2_fw)... when I went to rest it by holding down the rest button for 30 seconds, nothing appeared to happen. The light for the WLAN is now out. When I go to directly connect it to a computer, it says 'limited connectivity' local only. The Power, 1, and Internet lights still blink. I cannot access the web browser utility at 192.168.1.1 (nothing loads). Resetting still doesn't appear to do anything (lights don't flash off or change or anything)... Any ideas?

    Open a DOS window and do "ping 192.168.1.1". If you get replies, there's still a chance. If it times out or any other error message then it can't be helped. If the router is less than 3 years old, call linksys for a replacement.
    The box said windows xp or better... So I installed Linux!

  • Linksys SRW224G4 firmware upgrade fail!!!

    Hi,
    I have a switch SRW224G4 from Linksys and doesn't work now after an firmware upgrade!
    If is possible, I need that switch so a rapid answer will be appreciated!
    Simple, here the result when I try to install the firmware "ls_106-12216.ros" or "SRW224G4P_SRW248G4P_image_v1020.bix" that came from your web site!
    Here the result for "ls_106-12216.ros"
    Calculating file's checksum...OK
    Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>>>
    Writing to flash 0x32d980 records...
    Setting checksum: 0x19527ef1 , Address: 0x0
    OK.
    Flash programming success.
    Perform WARM BOOT ...
    ------ Performing the Power-On Self Test (POST) ------
    UART Channel Loopback Test........................PASS
    Testing the System SDRAM..........................PASS
    Boot1 Checksum Test...............................PASS
    Boot2 Checksum Test...............................PASS
    Flash Image Validation Test.......................PASS
    BOOT Software Version 1.0.0.06 Built  23-May-2005  16:58:25
    Linksys SmartSwitch based on 88E6218 with ARM946E-S.
    32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...
    100%
    FAIL !!! Check image for valid file.
    Please download a new image.
    Here the result for
    Downloading code using XMODEM.
    -- Download complete --
    Wrong file format. Writing aborted.
    Perform WARM BOOT ...
    Thanks,
    Steve

    I just tried updating the firmware in my SRW224G4 using the file "fesm-12216.ros" as indicated based on my bootloader version 1.0.0.06.
    Now it's stuck in a reboot loop. Here is the log from Hyperterminal starting from the update:
    Startup Menu
    [1]  Download Software
    [2]  Erase Flash File
    [3]  Password Recovery Procedure
    [4]  Enter Diagnostic Mode
    [5]  Set Terminal Baud-Rate
    [6]  Back
    Enter your choice or press 'ESC' to exit:
    Downloading code using XMODEM.
    -- Download complete --
    Calculating file's checksum...OK
    Erasing FLASH ->>>>>>>>>>>>>>>>>>>>>>>>
    Writing to flash 0x2e4180 records...
    Setting checksum: 0x1709abda , Address: 0x0
    OK.
    Flash programming success.
    Perform WARM BOOT ...
    ------ Performing the Power-On Self Test (POST) ------
    UART Channel Loopback Test........................PASS
    Testing the System SDRAM..........................PASS
    Boot1 Checksum Test...............................PASS
    Boot2 Checksum Test...............................PASS
    Flash Image Validation Test.......................PASS
    BOOT Software Version 1.0.0.06 Built  23-May-2005  16:58:25
    Linksys SmartSwitch based on 88E6218 with ARM946E-S.
    32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
    Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
    Preparing to decompress...
    100%
    Decompressing SW from flash
    100%
    OK
    Running from RAM...
    *** Running  SW  Ver. 1.2.2a  Date  05-Apr-2007  Time  15:35:50 ***
    HW version is 00.00.02
    Base Mac address is: 00:12:17:5d:08:d5
    Dram size is  : 32M bytes
    Dram first block size is  : 16969K bytes
    Dram first PTR is  : 0xF6D840
    Flash size is: 8M
    01-Jan-2000 01:01:05 %CDB-I-LOADCONFIG: Loading startup configuration.
    01-Jan-2000 01:01:08 %ERHG-F-SEND: BOXP_perform_smi_scan_of_devices_in_slot: inv
    alid device type is found: 268374443 on device 0
    ***** FATAL ERROR *****
    Reporting Task: ROOT.
    Software Version: 1.2.2a (date  05-Apr-2007 time  15:35:50)
    *****************  SYSTEM RESET  *****************
    It just repeats this over and over. The unit is out of warranty. Can I do anything to get this switch back up and running?
    Should I try reloading the firmware again or updating the bootloader?
    Any help would be most appreciated!
    Thanks.

Maybe you are looking for