WRVS4400N firmware upgrade to 1.01.03, VPN no longer works

I recently upgraded to firmware version 1.01.03 for my WRVS4400N. I have been having several problems with IPSec tunnels on the previous firmware and was hoping this release would resolve those issues. To my surprise this firmware version seems to be much much worse. Now I cannot even connect my point-to-point ipsec tunnels at all. I'm using the exact same configuration I was using before (yes I restored from factory and recreated). Anybody else have this problem with this new firmware? I've about had it with Linksys and their horrible VPN solutions. Any help would be appreciated.
Router 1: WRVS4400N
Router 2: WRV200
VPN Solution: IPSec
Thanks

We experienced the exact same problem with two of our new WRVS4400N's. We foolishly upgrade the firmware before realizing that the documentation for this significant release had not been upgraded. In the software business if the documentation isn['t done the software should never be released. Not only does it frustrate the customers but it also stresses the support organzation. Had we read the release notes we would have realized we should have 1.) backed up the settings (which would allow us to downgrade the firmware if we didn't like it - which is where we are now), 2.) reset the router to factory settings 3.) rebuild the settings from scratch. Once we finally got help from India to do this we were ok - though the VPN tunnell does go down at least once or twice a day. More frustrating though is our constant inability throughout the day to access websites (no problem pinging websites). Only way to resolve this is to reboot the router - again several times a day. We are now committed to downgrading back to the original firmware.

Similar Messages

After upgrading to Windows 8.1 iCloud no longer works on my PC

After upgrading to Windows 8.1 iCloud no longer works on my PC

I have the same problem - my data had better not be gone! Why won't Apple address this problem?

Ever since i downloaded OSX Mountain Lion, Express VPN no longer works properly for me. Even though it says I am connected, webpages refuse to load. However, everything works fine when its turned off. I cannot go on many websites without the VPN.

Ever since i downloaded OSX Mountain Lion, Express VPN no longer works properly for me. Even though it says I am connected, webpages refuse to load. However, connection speed is fine when its turned off. I cannot go on many websites without the VPN. My current location is Shanghai, China. OSX Mountain was installed this morning and everything worked fine until then. Is Express VPN not supported? What do i need to do in order to get it working again on my Macbook Pro (early 2011). I want to be able to go on websites such as Youtube, Facebook, Twitter, ect...

Hi,
I am having the same issue listed above on my new Mac Mini i just bought, I also contacted Express VPN support and got the same instructions with exception of the command to run in the utilities terminal. I tried the steps listed, and both commands (posted here, and sent to me directly by Express VPN support), and still unable to connect on my Mac Mini running OS X 10.8.2, but I am able to connect on my iPad and my MacBook which is running Mac OS X 10.6.8. Usually Express VPN is spot on with their customer support, but this is taking longer to get resolved. Here is the steps sent to me
Try doing the following to see if the problem gets resolved:
Please follow the instructions here: https://www.expressvpn.org/support/setting_dns_servers_mac_os
(should still be the same for Lion) and then add the following DNS servers: 8.8.8.8 & 208.67.222.220. After adding the DNS servers, please do the following steps as well:
Note: If you're connecting to your ISP via a PPPoE connection, then set the DNS servers on the PPPoE connection itself and then restart your computer for the DNS settings to take effect.
1. Click on Applications
2. Click on Utilities
3. Click on Terminal
4. Type the following command (without the quotes): "sudo killall -HUP mDNSResponder"
5. Press enter and then try reconnecting to the VPN.
If you're still unable to connect, please send us in the latest log files.
Hope this helps. Let us know how it goes.

My cisco vpn no longer works with Lion

After installing Lion, my cisco vpn no longer works. If I force boot in 32 bit mode it works fine, so appears to be a cisco client issue. Does anyone know if CISCO is working on 64bit client compatible with Lion?

Not sure this answer helps me or anyone else. My VPN connection no longer works in Lion. How do I re-set the parameters of my VPN connection to work in Lion?
Below is what my VPN screen look like:

Where can I download the latest version of Firefox 7? (I can't upgrade to Firefox 8 because Roboform no longer works with it)

Where can I download the latest (or last) version of Firefox 7? (I can't upgrade to Firefox 8 because Roboform no longer works with it)
Is there somewhere I can get the last version of Firefox 7?

Install Latest version 7.6.3 and try, you need upgrade
* http://www.roboform.com/support/news

VPN no longer working after upgrade to Mountain Lion

After upgrading to Snow Leopard, the Cisco VPN client stopped working.   This was due to the fact it ran in 64-bit, but SL allowed you to switch to 32bit which then the app still worked.
You also had the choice of using the MacOS 'VPN' program, but it always disconnected quite often for me.
After the upgrade, the Cisco VPN client no longer works at all, I assume again due to the fact 32bit is no longer around, however the Mac VPN client no longer works either. It will connect, however no traffic goes over the VPN (it gets blackholed) rendering it useless.
I have this behavior on multiple Macs, so I'm not sure if this is a known issue, or if the Mac VPN client no longer plays nice with the Cisco ASA firewalls?

It appears that ML no longer supports 32bit applications at all.
Therefore, you have 2 options:
1) Use the built in VPN client, you will need your IT's help for this as it requires the group name and password of your VPN server.   You can configure it by going to System Preferences -> Network and 'adding' an VPN (Cisco IPSec) interface.   I haven't had much luck with it, it works sometimes and sometimes it fails, but other people swear by it.
2) Move over to the Cisco AnyConnect VPN client, which does support 64bit. This will also require your IT department as they need to configure the SSL/AnyConnect VPN on the VPN device itself.   I went to this method yesterday and it's worked out great so far.

Firmware upgrade for keyboard failed now keys won't work

Hi
Hope someone can help, I recently upgraded my sisters intel imac and during the aluminium (USB) keyboard firmware upgrade it failed and now computer doesn't recognise keyboard keys but usb hub on keyboard that mouse is plugged into works fine. Another keyboard works fine which was handy when trying to type in the passwords to try to re update.
I have tried the following
1) searched discussions found advice on resetting nvram, and in open firmware (which on further research doesn't seem possible on this imac?) did control, option P R on start up.
3) EFI firmware upgrade was successful
4) have used disk utility to repair permissions
5) Looked in system profiler and keyboard usb hub is recognised but no keyboard. When another keyboard attached it recognises this fine and is in the system profiler
6) checked all usb ports
Main question - can I fix or do I have to get a new keyboard or perhaps it would be less stress, time wasted etc to just buy a new keyboard???
thanks
G

Hi, if the K/B is under warranty Apple will replace it FOC..Call Apple Help or ->
call in at the local Apple Store or Apple Approved Service Agent.

Cisco VPN no longer works with the E4200

VPN issue with the E4200. Validated that VPN passthrough is enabled. Using Cisco VPN as the client. Used to work prior to the firmware upgrade so not sure what has changed. Error code on the Cisco VPN client is "Secure VPN connection terminated by local client. Reason 414. Failed to establish a TCP connection."
Any help would be appreciated.

Hi all,
i just had time to to a network capture
The ip have been changed but btw :
- 172.20.10.2 = A computer conntect to internet that will try to reach the vpn server behind the E4200
- 77.56.226.107 = The internet valid ip address of the Linksys E4200 router.
So below is the proof that GRE protocol is not forwarded/passing the router.
Frames 29/30/31 : Standard TCP/IP communication intialization. SYN, SNY ACK, ACK....
Frames 32/34/36/37/38/39 : initialization of pp2p using port 1723
Frame 43 : ACK of 39
Frames 40,52,67,80... Request send using protocol 47 GRE... and the server not responding as the router blocks them...
No.
Time
Source
Destination
Protocol
Length
Info
28
7.122278
138.188.101.189
172.20.10.2
DNS
198
Standard query response A 77.56.226.107
29
7.141732
172.20.10.2
77.56.226.107
TCP
62
49395 > pptp [SYN] Seq=0 Win=8192 Len=0 MSS=1460 SACK_PERM=1
30
7.217517
77.56.226.107
172.20.10.2
TCP
62
pptp > 49395 [SYN, ACK] Seq=0 Ack=1 Win=5840 Len=0 MSS=1380 SACK_PERM=1
31
7.217835
172.20.10.2
77.56.226.107
TCP
54
49395 > pptp [ACK] Seq=1 Ack=1 Win=16560 Len=0
32
7.221922
172.20.10.2
77.56.226.107
PPTP
210
Start-Control-Connection-Request
34
7.294936
77.56.226.107
172.20.10.2
TCP
54
pptp > 49395 [ACK] Seq=1 Ack=157 Win=6432 Len=0
36
7.351526
77.56.226.107
172.20.10.2
PPTP
210
Start-Control-Connection-Reply
37
7.351622
172.20.10.2
77.56.226.107
PPTP
222
Outgoing-Call-Request
38
7.428474
77.56.226.107
172.20.10.2
PPTP
86
Outgoing-Call-Reply
39
7.445873
172.20.10.2
77.56.226.107
PPTP
78
Set-Link-Info
40
7.453787
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
43
7.549399
77.56.226.107
172.20.10.2
TCP
54
pptp > 49395 [ACK] Seq=189 Ack=349 Win=7504 Len=0
52
9.469811
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
67
12.511434
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
80
16.567525
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
81
20.623443
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
83
24.679479
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
85
28.735523
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
86
32.791514
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
87
36.847452
172.20.10.2
77.56.226.107
GRE
71
Encapsulated PPP
88
37.797042
77.56.226.107
172.20.10.2
TCP
54
pptp > 49395 [FIN, ACK] Seq=189 Ack=349 Win=7504 Len=0
89
37.797165
172.20.10.2
77.56.226.107
TCP
54
49395 > pptp [ACK] Seq=349 Ack=190 Win=16372 Len=0
90
37.801537
172.20.10.2
77.56.226.107
TCP
54
49395 > pptp [FIN, ACK] Seq=349 Ack=190 Win=16372 Len=0
93
37.876767
77.56.226.107
172.20.10.2
TCP
54
pptp > 49395 [ACK] Seq=190 Ack=350 Win=7504 Len=0

Iphone 4 since upgrade to ios 5.1.1 no longer works with made for itunes, iphone devices.

Ever since I upgraded to IOS 5.1.1 my Iphone no longer works for playing music thorugh my Apline car unit, My Logic 3 clock radio, and a Next made for ipod device.
I can sync through ITunes on the PC and can also play videos through the HDMI adapter.   My wifes iphone 4s and the kids hand me down iphone 3s still play fine through these made for Itunes , Ipod , Iphone devices.
I want to downgrade back to the prior IOS I had before Apple encouraged me to install this bugged one.   How do I go about getting a legit non jailbroken prior IOS version installed on my Iphone?
Is Apple aware of this issue , as I have seen blogs about this it is affecting other people?   Will this issue be resolved with ios 6?
Can I get the beta ?
Thanks,
Douglas

Agreed. Same thing here. Just bought a late model Alpine INE-S920Hd and it is all kinds of broken. I think this is happening because Apple shifted the music and video. Totally buggy. Bluetooth refuses to work properly, too. A2dp keeps stealing the audio from Pandora in the Alpine interface. The ipod controls dont work at all.

After upgrading to iOS6 my e-mail no longer works. How do I get it back?

I upgraded to iOS6 and now my e-mail no longer works. What do I do to get it back? It is stuck. I have restarted the iPad multiple times, checked my settings to no avail. I know the accouunt still works as I can access it on my PC. Help!! PLease

The button sounds like it sends a video to vodpod.com but that doesn't match what I see for the extension. The other two extensions came up with a search for vodpod but don't specifically mention vodpod.
* Flash Video Downloader - Youtube Downloader :: Add-ons for Firefox<br>https://addons.mozilla.org/en-US/firefox/addon/flash-video-downloader-youtube/
* Easy YouTube Video Downloader :: Add-ons for Firefox<br>https://addons.mozilla.org/en-US/firefox/addon/easy-youtube-video-downl-10137/
* Share Video :: Add-ons for Firefox<br>https://addons.mozilla.org/en-US/firefox/addon/share-video/

Corporate VPN no longer works on WRT310N

I had a WRT54G router installed and my corporate VPN worked fine. I gave that one to a relative, replacing it with a WRT310N, which comes with "all" of the VPN settings enabled. I tried the corporate VPN, and it worked for about 10 minutes. Now, I cannot connect at all. My company did not change anything, co-workers can connect through their home networks. Other computers on my network have no issues getting out to the network. Any ideas as to what I should be looking for?
Thanks

Login to the router's setup page and click on Security tab,uncheck "Filter Anonymous Internet Requests" and click on save settings...Click on subtab VPN Passthrough and check L2TP Passthrough if you have opened the ports on the router.

Upgraded from RH9 to RH11 Search No Longer Working

Hello,
Situation:
               Upgraded several projects from RH9 to RH11
               WebHelp Pro Output
               RoboHelp Server 9
Search no longer works for upgraded RH11 projects. No matter the topic or keyword entered, results are zero.
Search works on RH9 projects.
I looked through forums for similar situations, I didn't find any for RH11. Some solutions for RH10 said to verify the whfts file included all the xml packages and the RH11 output does. Others had to do with settings in WebHelp but couldn't find anything specific to WebHelp Pro.
Any ideas?
Thanks,
Julie

Update...it seems the fact that I am publishing to RH Server 9 is the problem. I received word from Adobe tech support:
"We have fixed that issue and soon we are releasing the patch for RHS 9 to support RH 11."
The expected patch is expected to be delivered by end of March 2014.
Thanks for all who helped.

Windows 8.1 on Envy 17 upgraded to pro.. refresh / reset no longer works

hi peeps
i was testing out the refresh and reset options when i first got the laptop they worked like normal.. then i upgraded to pro via control panel/add features to windows
the refresh and reset options no longer work.. how can i edit those functions to point to recovery partition

Hi @icp_wolverine
I understand that after you upgraded to a Windows Pro version and you are no longer able to do a system refresh or Microsoft restore.
If you did not overwrite the recovery partition when you did the upgrade you should be able to do a system recovery using the recovery manager.
Performing an HP system recovery (Windows 8)
If you did overwrite the recovery manager and you created recovery CDs then you can use them to recover your system.
If you are unable to do any of the above suggestions, please contact HP support and inquire about obtaining a recovery kit for your notebook.
Please call our technical support at 800 474 6836. If you live outside the US/Canada Region, please click the link below to get a support number for your region.
World Wide Phone Support
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

WRVS4400N Firmware upgrade fails

I've trying to upgrade the Firmware of WRVS4400N from 2.0.0.9 to the newest 2.0.1.3. Backup setting, upload the new firmware in the webinterface. Everything ok. Then I wait almost an hour, but the router did not reboot and reconnect to the webinterface. Instead, the router blinking on "Power" an "Diag". So i try to reset the router at the reset button backsides. But nothing happens, also these lamps blinking. Also I cannot connect to the webinterface. What's going on here? How can I solve this problem?
Regards Göran

The 126401-02 patch is for Netra T2000 machines.
If you have a regular T2000, use the 126399-02 firmware patch

Upgraded router VPN no longer working - LCP: timeout sending Config-Request

I recently upgraded my small office router from a Linksys WRT54G to a Linksys WRT610N. I duplicated all of the port forwarding configs from my previous router, but everytime I try to connect to my server I get the following error:
Could not negotiate a connection with the remote PPP server. Please verify your settings and try again.
The ports I have forwarded to my server are the following:
1701 UDP
500 UDP
1723 TCP
4500 UDP
While I am connecting I have been watching the log from Server Admin, and this is what I see:
2008-07-11 06:09:35 PDT Incoming call... Address given to client = 192.168.1.63
Fri Jul 11 06:09:35 2008 : Directory Services Authentication plugin initialized
Fri Jul 11 06:09:35 2008 : Directory Services Authorization plugin initialized
Fri Jul 11 06:09:35 2008 : PPTP incoming call in progress from '76.172.xxx.xxx'...
Fri Jul 11 06:09:35 2008 : PPTP connection established.
Fri Jul 11 06:09:35 2008 : using link 0
Fri Jul 11 06:09:35 2008 : Using interface ppp0
Fri Jul 11 06:09:35 2008 : Connect: ppp0 <--> socket[34:17]
Fri Jul 11 06:09:35 2008 : sent [LCP ConfReq id=0x1 <asyncmap 0x0> <auth chap MS-v2> <magic 0xef7517xx> <pcomp> <accomp>]
Fri Jul 11 06:10:05 2008 : LCP: timeout sending Config-Requests
Fri Jul 11 06:10:05 2008 : Connection terminated.
Fri Jul 11 06:10:05 2008 : PPTP disconnecting...
Fri Jul 11 06:10:05 2008 : PPTP disconnected
2008-07-11 06:10:05 PDT --> Client with address = 192.168.1.63 has hungup
I am still using 10.5.3. This may be very obvious to someone, but I'd appreciate any help.
Thanks!
Scott

I am having sever issues with routers vs. VPN and I am hoping someone here can tell me how they got PPTP and L2TP working through the Apple Airport Extreme.
Basically, I used to have a cheap, old, but perfectly working Linksys router. I opened ports for PPTP and L2TP pass through and VPN worked fine. I decided to upgrade the router because I wanted something with basic firewall functionality...
I tried two new linksys products and gave up in disgust. Then I thought I had a brainwave and ordered the Apple Extreme Base Station. Well, this is almost as hopeless.
I can get PPTP to connect now but the remote clients can't connect to the AFP server. L2TP simply won't work. I have 1701, 500, 1723 and 4500 ports forwarded to my server so I don't know what I am doing wrong.
Also, I see on Apple's Server page that the Server will set up the Apple Extreme Base Station automatically??? How does this work?
Lastly, Do I want to enable NAT port mapping protocol?
Thank you,
Gareth

WRVS4400N firmware upgrade to 1.01.03, VPN no longer works

Similar Messages

Maybe you are looking for