WRVS4400N Firmware V1.1.03 QoS Problem

With this router, there seems to be a problem with the V1.1.03 firmware. I cannot save any of it's QoS/ CoS settings on any of the pages, from either a wireless OR wired device HTTP session.
If I try to create my own service in the bandwidth limitations, when I save settings, it defaults back to the first 2 or 3 entries in the services list. It's very annoying.
Is there a fix for this?

Allow me to demonstrate.
I add custom services.
I click "SAVE SETTINGS"
I get this result.
Maybe someone there could take 2 seconds to answer why the router would do this.... or maybe tell me why I cannot assign priority to ports... or do any QoS/CoS settings AT ALL?
Message Edited by JZulkeski on 02-24-2008 10:52 AM

Similar Messages

WRVS4400N Firmware 1.1.03 problem

I recently updated my WRVS4400N firmware to 1.01.03. I use WPA-Personal with AES encryption security for my wireless laptops. I disabled Wireless SSID Broadcast and only allow my laptop MAC address to access my router. After I upgraded to 1.1.03 which is the latest firmware from Linksys.com. My wireless laptops drop session all the time. I rebuilt the client wireless profile did not help. Does anyone have the similar problem?
Brian

Yes, I reset several times and also reset it by holding the reset button at the back of the device several seconds without helping.

Is there any limitation of firmware or hardware for QoS configuration (4400 controller & 1252 AP's)

Hi Experts,
Before proceeding for adding AP model 1131 and 1252 into my set-up , I need to know whether any limitation of firmware or hardware for QoS configuration in wireless set-up .
I have 4400 controller and 1130 & 1250 AP models.

Hi Vinod,
Since you have 4400 controllers, you can run upto WLC 7.0.x code. Refer this for more detail
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
there is no specific limitation to 1131/1252 AP model as such, everything is WLC software dependent.
From later software 7.4.x,7.6.x,8.x, lots of improvement for QoS configuration & bandwidth control, but since your controller is old hardware, you cannot have those latest features.
here is a reference post on how QoS works in wireless environment
http://mrncciew.com/2012/11/28/understanding-wireless-qos-part-1/
HTH
Rasika
*** Pls rate all useful responses ****

ASR1001 QOS Problem %QOS-4-TUN_MOV_FAIL

Dear member,
I have facing a problem on the ASR with QOS problem, I configured a hqos on phyical interface and hqos on tunnel interface, the number of tunnel about 350.
I check on the logging, the QOS on tunnel was continues fail and install.
============================================
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2000.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2780, suspending policy.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2000, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel3080.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel3080, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2380.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel2380, suspending policy.
%QOS-4-TUN_MOV_FAIL: Queueing hierarchy move failed on Tunnel70, suspending policy.
%QOS-6-TUN_INSTALL: Installing suspended policy on Tunnel2140.
============================================
Any member have this experience.
Attach the QoS configuration for reference.
Regards
Russ

Seem not related to this bug as ASR only suspended policy without reboot.
Cisco IOS Software, IOS-XE Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.2(4)S, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Mon 23-Jul-12 20:03 by mcpre
IOS XE Version: 03.07.00.S
License Level: adventerprise
License Type: Permanent
Next reload license Level: adventerprise
cisco ASR1001 (1RU) processor with 1156392K/6147K bytes of memory.
Processor board ID SSI170805JC
4 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
7741439K bytes of eUSB flash at bootflash:.
Configuration register is 0x2102

G5 Firmware update necessary? Random problems since Tiger upgrade.

I have a PowerMac G5 (7,2) with a 1.8 GHz PowerPC 970 (2.2) CPU running under boot version 5.1.4f0. I have added memory.
I apparently upgraded from OS 9 to 10.2.8 without running any firmware updates. I quite frankly don't remember. I have since upgraded to Tiger, directly from 10.2.8. (There were OS X versions in between, I'm told. *wry smile*)
I am now having random problems.
The machine won't sleep. Display will but tower won't.
On occasion when I boot it up, I get the blue screen and nothing else; I have to shut it off with the power button and restart.
iPhoto (ancient version) is running agonizingly slowly (better since I did the fix suggested in the iPhoto forum in answer to someone else's question).
A short while ago, (in the last week) I noticed that some of my rules in mail ceased functioning (while others work fine). I deleted and recreated them to no avail. I previously had serious Mail problems that I fixed thanks to Mr. Gost, but those were largely of my own creation, so this latter might be unrelated.
If I'm reading things on the various boards and in Apple's Support forum right, in order to truly fix this I should deal with the firmware, to wit:
1. temporarily remove the memory I added (not factory-installed)
2. somehow (handwave) install OS 9 OR boot up from a OS 9 disk
3. download and install the 5.1.5f2 uniprocessor firmware update that Software Update keeps insisting I need.
4. reinstall the added memory
5. If I've reinstalled OS 9, reinstall 10.2.8 and then reinstall Tiger. (because I can't go directly from 9 to 10.4, right?) Otherwise, a clean install of Tiger might be a good idea.
Is this accurate?
Should this solve my blue screen and non-sleeping issues?
Are those issues indicative of a serious problem, or just annoying?
Is there more than one firmware update I should be using?
Will updating my firmware at this point create more issues than it is worth (as I'm seeing that many people had issues after firmware updates?)
Also, these problems seem to have intensified since the update to 4.10. Can I go back to 4... um... the last update? If so, can you point me to directions?
Sorry to be so verbose. I'm obviously more than a little behind the bell curve on this upgrade. The version of iPhoto I want (6) isn't even sold anymore.

Software updater insists the firmware update I need is 5.1.5f2. The only information I can find on this is on a 2004 page at apple support (http://docs.info.apple.com/article.html?artnum=86117) that states:
These firmware updates cannot be installed when the computer is started up from Mac OS X. In order to install them, you must start up the computer from a Mac OS 8 or Mac OS 9 System Folder on the computer's hard disk (not from a CD).
When you click on the technical details it says:
Remove any third part RAM before installing this Firmware Update. After the Firmware Updater has verified that it has been completed correctly, you can re-install your third party RAM.
There are other firmware updates, but they don't appear to address the issues I have been having, and they're not what Software Updater says it needs. Am I missing something obvious here?
I will check the USB devices. Thank you.

Airport time capsule Extreme dropping connection issue i have already upgraded new firmware 7.7.3 but problem is still in wifi connectivity drop please solve this issue i have expanded my money in tc drive

time capsule drop wifi connection issue .I have already upgraded new firmware 7.7.3 but problem in not solve i am very confuse to resolving this issue.also i attached my log here.
May 15 11:37:43
5
Initialized (firmware 7.7.3).
May 15 11:37:50
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 11:37:50
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 11:37:50
5
Rotated TKIP group key.
May 15 11:37:51
5
Clock synchronized to network time server time.apple.com (adjusted +1 seconds).
May 15 11:37:54
5
Associated with station b8:e8:56:1f:2c:98
May 15 11:37:54
5
Installed unicast CCMP key for supplicant b8:e8:56:1f:2c:98
May 15 11:38:27
5
Associated with station 78:a3:e4:ba:90:42
May 15 11:38:27
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 11:39:14
5
Connection accepted from [::ffff:192.168.1.170]:49439.
May 15 11:40:49
5
SMB/CIFS login OK from [email protected].
May 15 11:43:14
5
Connection accepted from [::ffff:192.168.1.170]:49452.
May 15 11:43:19
5
Connection accepted from [::ffff:192.168.1.170]:49454.
May 15 11:43:20
5
Connection accepted from [::ffff:192.168.1.170]:49456.
May 15 11:43:42
5
Disassociated with station b8:e8:56:1f:2c:98
May 15 11:43:43
5
Rotated TKIP group key.
May 15 11:44:20
5
Connection accepted from [::ffff:192.168.1.170]:49460.
May 15 11:45:21
5
SMB/CIFS login OK from [email protected].
May 15 11:47:33
5
Associated with station b8:e8:56:1f:2c:98
May 15 11:47:33
5
Installed unicast CCMP key for supplicant b8:e8:56:1f:2c:98
May 15 11:47:34
5
Disassociated with station b8:e8:56:1f:2c:98
May 15 11:47:35
5
Rotated TKIP group key.
May 15 11:47:57
5
Associated with station e4:92:fb:dc:02:0b
May 15 11:47:57
5
Installed unicast CCMP key for supplicant e4:92:fb:dc:02:0b
May 15 11:49:25
5
SMB/CIFS login OK from [email protected].
May 15 11:50:37
5
Connection accepted from [::ffff:192.168.1.170]:49472.
May 15 11:50:42
5
Connection accepted from [::ffff:192.168.1.170]:49474.
May 15 11:50:44
5
Connection accepted from [::ffff:192.168.1.170]:49476.
May 15 11:51:18
5
SMB/CIFS login OK from [email protected].
May 15 11:51:25
5
SMB/CIFS login OK from [email protected].
May 15 11:51:53
5
Connection accepted from [::ffff:192.168.1.170]:49478.
May 15 11:53:07
5
Idle timeout for station e4:92:fb:dc:02:0b
May 15 11:53:07
5
Disassociating with station e4:92:fb:dc:02:0b (reserved 4).
May 15 11:53:07
5
Disassociated with station e4:92:fb:dc:02:0b
May 15 11:53:07
5
Rotated TKIP group key.
May 15 11:54:45
5
Connection accepted from [::ffff:192.168.1.170]:49497.
May 15 11:54:52
5
Connection accepted from [::ffff:192.168.1.170]:49499.
May 15 11:54:57
5
Connection accepted from [::ffff:192.168.1.170]:49502.
May 15 11:55:15
5
Connection accepted from [::ffff:192.168.1.170]:49504.
May 15 11:55:24
5
Connection accepted from [::ffff:192.168.1.170]:49506.
May 15 11:55:45
5
Connection accepted from [::ffff:192.168.1.170]:49508.
May 15 12:05:39
5
SMB/CIFS login OK from [email protected].
May 15 12:05:40
5
unloading current configuration.
May 15 12:05:55
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 12:05:55
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 12:05:55
5
Rotated TKIP group key.
May 15 12:05:56
5
Clock synchronized to network time server time.apple.com (adjusted +0 seconds).
May 15 12:06:00
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:06:00
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:06:45
5
Disassociated with station 78:a3:e4:ba:90:42
May 15 12:06:45
5
Rotated TKIP group key.
May 15 12:07:19
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:07:19
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:09:15
5
Connection accepted from [::ffff:192.168.1.170]:49576.
May 15 12:09:35
5
Connection accepted from [::ffff:192.168.1.170]:49578.
May 15 12:09:49
5
Connection accepted from [::ffff:192.168.1.170]:49580.
May 15 12:25:40
5
Connection accepted from [::ffff:192.168.1.170]:49709.
May 15 12:25:51
5
Connection accepted from [::ffff:192.168.1.170]:49711.
May 15 12:26:12
5
Connection accepted from [::ffff:192.168.1.170]:49717.
May 15 12:27:40
5
Connection accepted from [::ffff:192.168.1.170]:49723.
May 15 12:27:41
5
unloading current configuration.
May 15 12:27:56
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 12:27:56
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 12:27:56
5
Rotated TKIP group key.
May 15 12:28:00
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:28:00
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:29:23
5
SMB/CIFS login OK from [email protected].
May 15 12:29:31
5
Connection accepted from [::ffff:192.168.1.170]:49730.
May 15 12:29:31
5
Connection accepted from [::ffff:192.168.1.170]:49732.
May 15 12:34:15
5
Connection accepted from [::ffff:192.168.1.170]:49739.
May 15 12:34:16
5
unloading current configuration.
May 15 12:34:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 12:34:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 12:34:31
5
Rotated TKIP group key.
May 15 12:34:49
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:34:50
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:36:07
5
Connection accepted from [::ffff:192.168.1.170]:49745.
May 15 12:36:08
5
Connection accepted from [::ffff:192.168.1.170]:49747.
May 15 12:40:40
5
Associated with station 10:68:3f:46:d2:69
May 15 12:40:41
1
WPA handshake failed with STA 10:68:3f:46:d2:69 likely due to bad password from client
May 15 12:40:41
5
Deauthenticating with station 10:68:3f:46:d2:69 (reserved 2).
May 15 12:40:41
5
Disassociated with station 10:68:3f:46:d2:69
May 15 12:41:48
5
Disassociated with station 10:68:3f:46:d2:69
May 15 12:42:12
5
Connection accepted from [::ffff:192.168.1.170]:49759.
May 15 12:42:13
5
unloading current configuration.
May 15 12:42:28
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 12:42:28
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 12:42:28
5
Rotated TKIP group key.
May 15 12:42:32
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:42:32
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:44:04
5
Connection accepted from [::ffff:192.168.1.170]:49768.
May 15 12:44:10
5
Connection accepted from [::ffff:192.168.1.170]:49771.
May 15 12:45:03
5
Connection accepted from [::ffff:192.168.1.170]:49773.
May 15 12:45:03
5
unloading current configuration.
May 15 12:45:18
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 12:45:18
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 12:45:18
5
Rotated TKIP group key.
May 15 12:45:23
5
Associated with station 78:a3:e4:ba:90:42
May 15 12:45:23
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 12:46:23
5
Associated with station e4:92:fb:dc:02:0b
May 15 12:46:24
5
Installed unicast CCMP key for supplicant e4:92:fb:dc:02:0b
May 15 12:46:43
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:46:43
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:46:58
5
Connection accepted from [::ffff:192.168.1.170]:49780.
May 15 12:47:02
5
Connection accepted from [::ffff:192.168.1.170]:49782.
May 15 12:47:05
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:47:05
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:47:13
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:47:14
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:47:27
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:47:30
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:47:39
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:47:40
5
Rotated TKIP group key.
May 15 12:47:44
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:47:44
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:49:07
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:49:07
5
Rotated TKIP group key.
May 15 12:49:13
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:49:13
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:51:19
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:20
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:20
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:51:26
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:30
5
Deauthenticating with station 24:fd:52:d0:3c:50 (reserved 2).
May 15 12:51:30
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:51:31
5
Rotated TKIP group key.
May 15 12:51:31
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:31
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:51:34
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:38
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:40
5
Deauthenticating with station 24:fd:52:d0:3c:50 (reserved 2).
May 15 12:51:40
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:51:40
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:41
5
Rotated TKIP group key.
May 15 12:51:42
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:42
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:51:47
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:49
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:49
5
Installed unicast CCMP key for supplicant 24:fd:52:d0:3c:50
May 15 12:51:55
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:57
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:51:59
5
Deauthenticating with station 24:fd:52:d0:3c:50 (reserved 2).
May 15 12:51:59
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:51:59
5
Rotated TKIP group key.
May 15 12:52:05
5
Associated with station 24:fd:52:d0:3c:50
May 15 12:52:09
5
Deauthenticating with station 24:fd:52:d0:3c:50 (reserved 2).
May 15 12:52:09
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:52:20
5
Disassociated with station 24:fd:52:d0:3c:50
May 15 12:59:22
5
Connection accepted from [::ffff:192.168.1.170]:49810.
May 15 12:59:22
5
Connection accepted from [::ffff:192.168.1.170]:49812.
May 15 13:00:07
5
Connection accepted from [::ffff:192.168.1.170]:49817.
May 15 13:00:07
5
unloading current configuration.
May 15 13:00:22
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 13:00:22
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 13:00:22
5
Rotated TKIP group key.
May 15 13:00:35
5
Associated with station 78:a3:e4:ba:90:42
May 15 13:00:35
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 13:02:00
5
Connection accepted from [::ffff:192.168.1.170]:49826.
May 15 13:02:00
5
Connection accepted from [::ffff:192.168.1.170]:49828.
May 15 13:03:14
5
Connection accepted from [::ffff:192.168.1.170]:49832.
May 15 13:03:15
5
unloading current configuration.
May 15 13:03:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 13:03:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 13:03:31
5
Rotated TKIP group key.
May 15 13:04:03
5
Associated with station 78:a3:e4:ba:90:42
May 15 13:04:03
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 13:05:07
5
Connection accepted from [::ffff:192.168.1.170]:49843.
May 15 13:05:07
5
Connection accepted from [::ffff:192.168.1.170]:49845.
May 15 13:06:15
5
Connection accepted from [::ffff:192.168.1.170]:49848.
May 15 13:06:16
5
unloading current configuration.
May 15 13:06:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 3).
May 15 13:06:31
5
Deauthenticating with station ff:ff:ff:ff:ff:ff (reserved 2).
May 15 13:06:31
5
Rotated TKIP group key.
May 15 13:07:04
5
Associated with station 78:a3:e4:ba:90:42
May 15 13:07:04
5
Installed unicast CCMP key for supplicant 78:a3:e4:ba:90:42
May 15 13:08:08
5
Connection accepted from [::ffff:192.168.1.170]:49854.
May 15 13:08:09
5
Connection accepted from [::ffff:192.168.1.170]:49856.
May 15 13:08:20
5
Connection accepted from [::ffff:192.168.1.170]:49858.
May 15 13:12:31
5
unloading current configuration.
May 15 13:32:36
1
WPA handshake failed with STA 1c:7b:21:9c:20:fd likely due to bad password from client
May 15 13:32:57
1
WPA handshake failed with STA 1c:7b:21:9c:20:fd likely due to bad password from client
May 15 13:33:09
1
WPA handshake failed with STA 1c:7b:21:9c:20:fd likely due to bad password from client
May 15 13:33:22
1
WPA handshake failed with STA 1c:7b:21:9c:20:fd likely due to bad password from client
May 15 13:33:33
1
WPA handshake failed with STA 1c:7b:21:9c:20:fd likely due to bad password from client
May 15 15:21:21
1
WPA handshake failed with STA 10:68:3f:46:d2:69 likely due to bad password from client
May 15 15:21:26
1
WPA handshake failed with STA 10:68:3f:46:d2:69 likely due to bad password from client
May 15 15:21:41
1
WPA handshake failed with STA 10:68:3f:46:d2:69 likely due to bad password from client

It says you have the wrong password.
WPA handshake failed with STA 10:68:3f:46:d2:69 likely due to bad password from client
Reset the TC to factory and start again.
But do not be surprised if the v5 utility no longer works to do the setup.

Firmware Fix for Power Off Problems?

I'm running out of time to exchange my 5G and I'm not sure if the general consensus is that a firmware update will fix the problem with the failure of the Ipod to power down while watching a video. Pressing and holding the play button will not cut off the Ipod. I have to go all the way out to the main menu and load a song before it will cut off. Anyone know if this will or can be fixed with firmware? Thanks!
TreoBud

That's exactly what it is. While watching a movie, the hard drive is almost continually spinning, especially towards the beginning. Sometimes, you do have to pause it, go to the main menu, and wait a minute or two before it will turn off. You can tell by the vibration in your hand - if it's vibrating, it won't turn off. The second it stops, it'll turn off. It's kind of annoying, but that's the way it works. No firmare update will fix it, it's a hardware thing.

WRVS4400N firmware upgrade to 1.01.03, VPN no longer works

I recently upgraded to firmware version 1.01.03 for my WRVS4400N. I have been having several problems with IPSec tunnels on the previous firmware and was hoping this release would resolve those issues. To my surprise this firmware version seems to be much much worse. Now I cannot even connect my point-to-point ipsec tunnels at all. I'm using the exact same configuration I was using before (yes I restored from factory and recreated). Anybody else have this problem with this new firmware? I've about had it with Linksys and their horrible VPN solutions. Any help would be appreciated.
Router 1: WRVS4400N
Router 2: WRV200
VPN Solution: IPSec
Thanks

We experienced the exact same problem with two of our new WRVS4400N's. We foolishly upgrade the firmware before realizing that the documentation for this significant release had not been upgraded. In the software business if the documentation isn['t done the software should never be released. Not only does it frustrate the customers but it also stresses the support organzation. Had we read the release notes we would have realized we should have 1.) backed up the settings (which would allow us to downgrade the firmware if we didn't like it - which is where we are now), 2.) reset the router to factory settings 3.) rebuild the settings from scratch. Once we finally got help from India to do this we were ok - though the VPN tunnell does go down at least once or twice a day. More frustrating though is our constant inability throughout the day to access websites (no problem pinging websites). Only way to resolve this is to reboot the router - again several times a day. We are now committed to downgrading back to the original firmware.

WRVS4400N Firmware upgrade fails

I've trying to upgrade the Firmware of WRVS4400N from 2.0.0.9 to the newest 2.0.1.3. Backup setting, upload the new firmware in the webinterface. Everything ok. Then I wait almost an hour, but the router did not reboot and reconnect to the webinterface. Instead, the router blinking on "Power" an "Diag". So i try to reset the router at the reset button backsides. But nothing happens, also these lamps blinking. Also I cannot connect to the webinterface. What's going on here? How can I solve this problem?
Regards Göran

The 126401-02 patch is for Netra T2000 machines.
If you have a regular T2000, use the 126399-02 firmware patch

WRVS4400N Firmwire Version v1.1.03 problem

I am having a lot of troubles connecting to my wireless WRVS4400N router after upgrading the firmwire to v1.1.03. I use WPA-PSK with AES option. Also turned on Wireless Client List to only allow my computers/laptop to access the router. It seems like WPA-PSK AES option does not work well with v1.1.03 firmwire.
Does anyone have problem connecting to the router via wireless connection? May be Linksys support team should look into this.
Brian.

After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you have not done this since the last firmware upgrade, then please do this now. If you saved a router configuration file, DO NOT use it.
If the above is not the problem, then your problem is most likely caused by a poor wireless connection.
There are many causes for poor wireless connections, and many solutions:
First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
In the router, make sure the "Radio Band" is set to "Wide".
Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4. For wireless n, make sure standard and wide bands are at least 2 channels apart. For example, try standard channel 11, and wide channel 9.
Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. Also, delete your current network (this will delete any old settings). Reboot computer. Return to "Preferred Networks" and re-enter your current network info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings". Reboot computer. It should connect automatically.
If the above does not fix your problem, download and install the latest driver for your wireless card.
Some users have reported improved wireless performance by switching to WPA encryption.
If you continue to have problems, try the following:
For wireless n routers, try setting the "n Transmission Rate" to 162 Mbps, and the (wireless g) "Transmission Rate" to 54 Mbps.
If you still have trouble, download and install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Hope this helps.
Message Edited by toomanydonuts on 03-16-2008 01:19 AM

Linksys WRVS4400N Firmware Bug!

i have problem whit my Firmware. I can not open all order of FTPs and i can`t Upload on a FTP and this of all Computers. Test: Cute FTP FileZilla Client SmartFTP Whats this for a bug? Its WDS coiming soon on WRVS4400N?

since it seams like you are having an issue with your firmware , you can perform a factory reset by holding in the button in on back of the router for 30 seconds, wait about 2 minutes and try to upgrade to the latest firmware.
Below is a link to help you with the firmware upgrade.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=4030&p_created=11601...
Good Luck,
Ttech

QoS Problem - Outbound Ethernet Marcation

Hi all,
I have a problem with QoS.
Everytime a voice packet go outbound through an Ethernet interface the router remove the DSCP marcation 46 (EF) and marks as 0. Serial interfaces work fine.
I've tried with different IOS versions but the problem is the same.
If anyone has faced this problem before, please let'me know what IOS version this QoS configuration work.
Cheers ///
Neirival de Sousa (Brazil/Angola)

Hi,
can yo be more specific about your hardware/software and general setup?
Also one more thing: are you sure it happens outbound? Could it be that a LAN switch is receiving the frame/IP packet and the default port settings for Catalysts kick in? QoS wise all LAN ports on the Catalyst switches are untrusted, thus any marking will be set to 0 (best effort), when received on such a port. You need to issue a "mls trust ..." command on each port, where markings should be passed unchanged. The "..." is "cos" or "dscp" and depends on hardware/IOS.
Hope this helps! Please rate all posts.
Regards, Martin

QOS problem (multicast) with 3750

Hi,
I need help to solve following problem.
I have setup qos in our 3750, see below.
Unicast traffic is handle correct, However with multicast streams the router set the dscp to 0
Has somebody any idea what is missing?
Too old sw?   Cisco IOS Software, C3750 Software (C3750-ADVIPSERVICESK9-M), Version 12.2(35)SE,
Regards Niklas
ip multicast-routing distributed
ip multicast multipath
mls qos srr-queue input priority-queue 1 bandwidth 10
mls qos srr-queue input dscp-map queue 1 threshold 1 46
mls qos srr-queue input dscp-map queue 2 threshold 1 11 24 30 48
mls qos srr-queue output dscp-map queue 1 threshold 1 48
mls qos srr-queue output dscp-map queue 2 threshold 1 46
mls qos srr-queue output dscp-map queue 3 threshold 1 40
mls qos srr-queue output dscp-map queue 4 threshold 1 11 24 30
mls qos
interface GigabitEthernet1/0/22
switchport access vlan 41
switchport mode access
load-interval 30
srr-queue bandwidth share 25 25 25 20
priority-queue out
mls qos trust dscp
interface GigabitEthernet1/0/23
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 40
switchport mode trunk
load-interval 30
srr-queue bandwidth share 25 25 25 20
priority-queue out
mls qos trust dscp

Hi,
Here comes the printouts:
with mls qos enabled:
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/22 statistics
GigabitEthernet1/0/22
dscp: incoming
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0            0            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
dscp: outgoing
0 - 4 :     8881981            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0          307            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
cos: incoming
0 - 4 :           0            0            0            0            0
5 - 7 :           0            0            0
cos: outgoing
0 - 4 :     8881981            0            0            0            0
5 - 7 :           0          307            0
Policer: Inprofile:            0 OutofProfile:            0
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/23 statistics
GigabitEthernet1/0/23
dscp: incoming
0 - 4 :     8931330            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0          202            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
dscp: outgoing
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0         1206            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
cos: incoming
0 - 4 :    11357772            0            0            0            0
5 - 7 :           0            2            0
cos: outgoing
0 - 4 :           0            0            0            0            0
5 - 7 :           0         1206            2
Policer: Inprofile:            0 OutofProfile:            0
cisco-Mcast#
mls qos disabled:
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/22 statistics
GigabitEthernet1/0/22
dscp: incoming
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0            0            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
dscp: outgoing
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0         7371            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0            0            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
cos: incoming
0 - 4 :           0            0            0            0            0
5 - 7 :           0            0            0
cos: outgoing
0 - 4 :        7371            0            0            0            0
5 - 7 :           0            0            0
Policer: Inprofile:            0 OutofProfile:            0
cisco-Mcast#sh mls qos interface gigabitEthernet 1/0/23 statistics
GigabitEthernet1/0/23
dscp: incoming
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0        23281            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0            0            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
dscp: outgoing
0 - 4 :           0            0            0            0            0
5 - 9 :           0            0            0            0            0
10 - 14 :           0            0            0            0            0
15 - 19 :           0            0            0            0            0
20 - 24 :           0            0            0            0            0
25 - 29 :           0            0            0            0            0
30 - 34 :           0            0            0            0            0
35 - 39 :           0            0            0            0            0
40 - 44 :           0            0            0            0            0
45 - 49 :           0            0            0            2            0
50 - 54 :           0            0            0            0            0
55 - 59 :           0            0            0            0            0
60 - 64 :           0            0            0            0
cos: incoming
0 - 4 :       29272            0            0            0            0
5 - 7 :           0            0            0
cos: outgoing
0 - 4 :           0            0            0            0            0
5 - 7 :           0            2            0
Policer: Inprofile:            0 OutofProfile:            0
cisco-Mcast#
BR Niklas

Using twoo NVIDIA 7300 cards: firmware bug? Screen refresh problem

strange bug with Mac Pro 2.66 Xeon:
I have two Displays, 20 and 23".
When both connected to the standard NVIDIA card in the Mac Pro, evreything is fine.
I ordered a second NVIDIA card wich I installed in slot 4, using 8 lanes for this card.
Now, when one display is connected to the standard card and the second display is connected to the second NVIDIA card, the screen of the display connected to the build in card (the 16 lanes card) does noet refresh correctly. You can not see what iMovie is displaying for example, iMovie screen is white and does not display what should be on screen.
Sometimes none of the main screen is refresehd (example: Safari content is not updated, while in fact it is!) but the mousecursor moves correctlyon screen.
Also third party software (like FotoMagico) is not updated on screen
Connecting both displays to one card and everything is fine!
A strange bug wich I guess is related to the Mac Pro firmware
I've tried the second NVIDIA card in all the PCI-E slots to see if this makes a difference, it does not.
I used the PCI-E configure tool to vhange the speed of the lanes for the PCI-E slots, also this makes no diffrence.
At this moment my second card is not usable.
This is a problem on all three Mac Pro's we tried this on (2.66 version, 2 machines with 1Gb RAM, 1 machine with 3Gb RAM), latest OS 10.4.7
Starting in safe mode makes no difference on either Mac Pro

I am running two 7300 GTs in my 2.66 GHz Mac Pro driving (2) 20" + (1) 30" Cinema Display. I am not seeing the issue you mention in iMovie. Quicktime flickers every once in a while when playing iTunes video content, but that started with the iTunes / Quicktime upgrade, not when I added the extra card.
I have my nVidia 7300 cards in slots 1 &2 each running 8 lanes. Might be worth a try. The 7300 is not that "high performance" that running in 8 lanes is going to make a huge difference in speed. What it will do for you is get the cards on an equal footing.

Nokia 5800 firmware v21....problem trying to updat...

Hi there...i have Nokia 5800,Hong Kong blue, product code 0575408...when i check on the Nokia website,it tells me that the firmware available for this model is v21.0.025...however....when i connect to the NSU...it tells me that the current firmware for my phone is the current one,v 11.0.0.09, and there is no need to update....anybody had this problem?or is there anybody that knows the cause of this?any help would be greatly appreciated.
cheers

Nokia care in the UK often reply quick but you nearly always get a scripted non-answer from them
@ mccbleue - That is true because things such as web links and extra programs can be added to firmware but other manufacturers do that too.
What should happen is that the release is delayed until it's ready for all. Nokia's regional offices would have to act quicker at regionalising the firmware. In the past on other models UK variants have ranged from same day release to the EURO1 variant to 8 weeks later, which just doesn't make sense.
This is probably the only way to put an end to the masses of posts from people in various countries asking when updates will be available in X country. This is not taking into account branded phones which is a problem in itself.
Other manufacturers can manage near simultaneous worldwide release for firmware, why can't nokia?
Message Edited by psychomania on 21-Apr-2009 02:55 PM

WRVS4400N Firmware V1.1.03 QoS Problem

Similar Messages

Maybe you are looking for