WRVS4400N IPSec VPN Advanced Settings Found

v1.00.16 - O.K. This is weird. I have had no luck with getting the Advanced Settings Button to do anything until now. I simply got lucky. The Advanced Settings Button works only when accessing the router menus using https locally on the LAN. Basically, https://192.168.1.1 Then find the IPS VPN Tab and press the Advanced Settings Button and wala there it is. When accessing the router using http://192.168.1.1, the button does nothing. Weird to say the least. Even with this, all of the certificate management buttons and menus are still missing. Did anyone find the certificate management menus and buttons in an earlier firmware version than v1.00.16?
I dug a little further and found that the CGI under the http portion of the program simply does not call the advanced web page. To get around this, simply type in: http://192.168.1.1/vpn_adv.htm
the vpn_adv.htm file is the web page that is hidden by the CGI.
If anyone can find any of the certificate manage web pages, I bet they are on the WRVS4400N as well ... only missing from the top menus / CGI. If you find one, please send it to me.
Thanks.
Message Edited by Aviator on 08-31-2007 02:52 PM

Good info!
Thanks!
I have this installed at a client site but refuse to mess with it as I finally got it working OK. it's still on firmware 1.00.15 I noticed .16 came out just about a week ago and I don't have a "spare" 4400N to test that on so I am leavign it all alone for now.
I do have some issues...mostly the VPN stuff, but like I said, I finally got it working so I'm not touching it.
Time to order another one and setup a dev environment......

Similar Messages

Authentication in advanced settings for pop outgoing is grayed out.

I'm not able to send outgoing emails while at work and our network admin told me to use authenticated smtp, port 587. So I went into advanced settings, found the Outgoing using port 587, but the Authentication button is grayed out. Any ideas how to enable it or why it's grayed out?

That didn't work for me either. I couldn't enter a password into the Outgoing Settings field and have it "stick". And I couldn't choose an authentication method.
But now I think I fixed it.
I've been syncing this account with my Mac for a while, and I'm just now getting this server in question to actually use authentication; I'm not sure, but I think I've been doing SMTP over TLS unauthenticated for a while now.
I believe what's happened is that there's some crud deep in my iPhone that's "stuck" on unauthenticated for that mail account. And I think the key is either the "Description" field or "Address" field.
That is, I removed and recreated my account from scratch, on my phone. The account previously had the Description "Personal", and when I recreated it, I once again gave it the description "Personal". This did not solve my problem. I could not get an Outgoing Settings password to stick, and I couldn't choose any form of Authentication.
Now I've recreated the account again from scratch, this time giving it a different Description and Address. Now I'm getting results.
But I'm getting even stranger results. I changed Description and Address, but the Host Name and User Name stayed the same--that must be the "key" in another way. Because now both of the accounts (I didn't destroy the original account settings) have the same description and same everything else.
Anyhow, I think I've cleared out whatever was getting stuck. The result is that if you have a brand-new iPhone, and you point it at a box that asks for AUTH, the iPhone will go through all sorts of hoops and jumps and detect what you have, and allow you to enter a password. But if you get a setting stuck in your iPhone somewhere, you won't be able to undo it without some effort. In my case, making a new mail account with a different "Description" and "Address".
And I've now cleaned everything up--I've removed one of the accounts, so now I only have one (can't tell which one was which, they were both identical), changed all the settings back to exactly the way they used to be, and I can still have an Outgoing Settings password, and choose Authentication. And outgoing mail actually works too...

Ipsec VPN site to site, best settings for optimal data transfer

I have a ISA570 at work and have set up an ipsec VPN site to site connection with my router at home which is a RV180. I'm trying to do large backups from my office to my home storage. Can you tell me what are the most efficient settings as far as the VPN connection is concerned to optimize the transfer rate? Also any settings that I may make on my Windows 7 workstation at work. I'm transferring from a worstation to the terrastation that I have at my home.

Hi Daniel,
I noticed that your post was located in the VPN Site to Site instead of the Small Business Security area. I have moved your post to the correct area so that you will get some help. As a Cisco customer with a service contract, you can call the small business support center to speak with an engineer. The phone numbers are located here:
https://www.cisco.com/en/US/support/tsd_cisco_small_business_support_center_contacts.html
Regards,
Cindy Toy
Cisco Small Business Community Manager
for Cisco Small Business Products
www.cisco.com/go/smallbizsupport
twitter: CiscoSBsupport

Wrvs4400n IPsev VPN interface

I have had no problems setting up other features of the wrvs4400n, even though it does dumb things like display the actual passwords for VPN Client Accounts in clear text, but when trying to configure the IPsec VPN portion of the wrvs4400n I keep getting strange -if not buggy- behavior as I try to adjust the settings.
Has anyone else run across any of these??
1) On the main IPsec VPN screen under "Key Management", I set PFS to "Enable", but PFS keeps setting itself back to "Disable" whenever I save settings.
2) Likewise the "Pre-Shared key" and "Key Life Time" keep reseting to blank and 0 respectively after saving settings. I get a warning that they are not set unless I reenter them so they are not being set and not displayed.
3) The "Advanced VPN Tunnel Setup" window which one must go to if one sets the "Remote Security Gateway Type" to "Any" in order to change "Local Identity" to "Name" (as instructed by another warning) does not seem to want to save ANY configuration information. So one can not change "Local Identity" to "Name", nor "Authentication", "Group" etc. and have them set when it opens again.
I notice that "PFS" is Always set to "Disable" in the "Advanced VPN Tunnel Setup" window, and I guess this is because it is not getting set in the main "IPsec VPN" window.
I notice also that I have to enable pop-ups in my browser for the "Advanced VPN Tunnel Setup" window to appear, even though this is not necessary for other windows like the logs, or help.
I'm using the latest firmware v1.00.13 and have tried setting IPsec up using Firefox and Safari, on windows, and Mac with the same result. Any ideas??
thanks!

It could have either been a problem flashing the firmware the first time or some bad behavior because of the pop-up window getting blocked and somehow messing with the internal config, but after I re-flashed and reset the router to defaults I've had no problems... Thanks!!

Cisco ASA 5505 site to site IPSec VPN with RV220W issue

I have a ASA5505 connected to RV220W through IPSec VPN. When using SMB to transfer large file, the ASA5505 will show error message:
CTM ERROR: Invalid input parameters, ctm_get_scb_prot_stats:1561
The error message from the debug crypto engine. When the message show, the speed of the transfer will slow down quickly, and even no data can be go through between ASA and the RV220W. But the IPSec SA and the IKE SA is active, and can ping the inside network in both site.
Both ASA5505 and the RV220W has been updated the latest firmware. I have surf the Google but no such related issue found.
Any suggestions on where to look would be much appreciated.
Thanks in advance
Terry

Hi Ted thanks for your reply and information.
The strange things happened in RV220W shows the IPSec sa is expired, but the ASA5505 IPSec and IKEv1 sa is active. Inside both site internal network can ping to other side, but cant transfer file through Windows SMB. It seems when I transfer over 4GBytes of file, it will start happening and required clear IPSec and IKEv1 sa so that the VPN tunnel will start up again.
I am already surrander for this issue......

Windows 8 and IPSec VPN issues

I have a number of customers that leverage the Cisco IPSec VPN. I can connect to the VPN without any problems but when I attempt to RDP, that fails. I have no RDP or ping or anything. Here are some more symptoms of the issues that I find odd:
Anyconnect works just fine
Fortinet VPN clients work fine
Sonicwall VPN clients work fine
Cisco IPSec VPN client is the only one affected
Cisco IPSec VPN client worked fine for months then just decided it was no longer going to allow RDP or ping
I have duplicated this issue on a half dozen or so laptops
This is on a Windows 8 laptop but I believe I have also experienced this on Windows 7
Just to clarify, the IPSec VPN does succesfully connect. But nothing else works after that. I do understand that AnyConnect is the direction that Cisco would like for people to move towards. Unfortunately, I have quite a few customers that are leveraging the IPSec VPN. I have been through a number of laptops in the last year and every single laptop had a working Cisco IPSec VPN for months....then one day it would just stop passing RDP.
Please somebody tell me that there is a workaround for this. I have played with the IP settings for the Cisco Systems virtual adapter in my network and sharing center. I've modified the binding order. I've compared a routeprint from a working laptop to mine....I'm not sure what else to do. I've uninstalled ALL VPN software and only reinstalled the Cisco VPN. So far the ONLY fix I have found is a clean install of Windows and that solution sucks.

Doing a little more homework on this and I noticed that the tunnel details show no bytes sent or recieved and no packets encrypted, decrypted, or discarded....everything is bypassed. My coworker (who is on Windows 7) is able to launch this VPN and connect to the customer's servers without issues and the tunnel details show all of the appropriate data.

SL IPSEC VPN Server Not working with Windows 7

I have an airport extreme and a mac mini w/ snow leopard server.
I am able to VPN into my network from my iPhone, MAC 10.6.2, & Windows XP. I am not able to VPN into my network from 2 different Windows 7 machines. I am able to VPN from a laptop running Windows 7 if I am on the LAN but can't vpn from the WAN. Any suggestions?
Tried this: http://support.microsoft.com/kb/947234 and tried this: http://support.microsoft.com/kb/926179/ all to no avail.
I used these instructions to config my windows 7 client:
General Tab:
put your server's address of resolvable name (vpn.yourserver.com)
Security Tab>Advanced>Settings...:
Require encryption ()disconnect if server declines
Microsoft CHAP Version 2 -only thing checked!
Security Tab:
IPSec Settings...
Your share secret - the one you put in the Mac OS X server VPN
Networking Tab:
L2TP IPSec VPN

hi urbancoffy,
boah what a hell....
let's look if there is a cure.....
this device is recognized under every other system than yours, right?
if so maybe your software is misconfigured or your usb connection is bad....
how to determine?
try other devices like an usb-stick
check bios if legacy usb support is on
check device manager (device plugged in) if it shows any information like a //dev_xxxx
if your usb port is ok
goto device manager and remove all usb devices (show hidden devices)
reboot and let the system determine the hub etc
plug in usb-hdd and see if it will be detected - keep in mind: you dont have to load a driver for a usb storage device by yourself
if the usb ports are ok and your hdd is recognized by other systems maybe it's time for a recovery of your system....
Message was edited by: Al-eX

RVL200 Ipsec VPN Problems

Hello Experts,
I managed to establish an Ipsec VPN connetion with 2 RVL200s between 2 Locations. So far so good.
It is possible to access network a form network b with WinXP PCs, but it is not possible to reach network a with Win7 PCs.
Whereelse it is possible to reach network b from network a from either type of windows pc.
And when you ping from the RVL200 (on both sides) to the other net you always get no replys to your ping.
Settings on both RVL200s are equal, except for that one is going over ADSL (network a) and the other is behind a cable modem (network b).
I have de-activated Firewalls, no change. Routing Tables look fine for me. IPv6 is de-activated in Win7 PCs. I have added static routes, no change.
Does anyone know where else I could look for a solution?
Many Thanks in advance.
J. Radix

Josef,
You state that you can reach from both sides of the routers and ping xp machines but not windows 7 machines? The router won't be restricting traffic based on operating systems on the lan, so I would look at possible firewalls on the windows 7 machines, anti-virus, nortons, anything that does packet inspection.

Outbound UDP 500 Connections Causing IPSEC VPN Headache

OK, I've got an issue that I need to toss out to the experts here. I set up an ipsec remote access profile on an ASA 5510 and was having connection problems (never completes phase 1). After some investigation, I saw that my connection was hitting the external interface and translating to an internal interface on UDP 500. I didn't have any NAT entries that would allow this action so upon investigation I see I have three internal outbound devices that are all being sourced and destined on UDP 500 (one of these devices was the translated destination for my ipsec vpn).
I'm at a loss as to how to get around this (other than shutting the machines down); I've tried enabling ipsec-pass-thru inspection and cleared the xlates for those devices but they still connect back up. Any suggestion on something else to try? I could possibly try creating an anyconnect profile, but it's more the point that I want to figure out why this is happening instead of just circumventing the issue.
Thanks in advance!

Hi Portu,
Sorry for the late reply, it is indeed 24 hours (86400). Somewhere I agree withthis logic, but why not? What would this cause?
BTW,
I believe to have found what is wrong or at least is not right. There was no 'nonat' rule in place for the protected traffic on our side. Although I find it strange that the tunnel is ok once it's setup from the remote end. They have no problems accessing our network here. I would expect them to have issues if the 'nonat' rule is missing, but they do not. It's only after a couple of days that the tunnel goes down from our end and stays up at the remote end, which of course leads to them not being able to access our network. SO hopefully this is it.
Regards,

Looking for help to set up l2tp Ipsec vpn on asa 5055

I am trying to set up a L2tp Ipsec vpn on asa 5055 and I am using windows 8.1 build in VPN client to connect to it. I got the following error. Anyone has experence please help.
Apr 17 22:48:21 [IKEv1]Group = DefaultRAGroup, IP = 209.171.88.81, All IPSec SA proposals found unacceptable!
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, sending notify message
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing blank hash payload
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing ipsec notify payload for msg id 1
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing qm hash payload
Apr 17 22:48:21 [IKEv1]IP = 209.171.88.81, IKE_DECODE SENDING Message (msgid=6a50f8f9) with payloads : HDR + HASH (8) + NOTIFY (11) + NONE (0) total length : 84
Apr 17 22:48:21 [IKEv1]Group = DefaultRAGroup, IP = 209.171.88.81, QM FSM error (P2 struct &0xad6946b8, mess id 0x1)!
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, IKE QM Responder FSM error history (struct &0xad6946b8) <state>, <event>: QM_DONE, EV_ERROR-->QM_BLD_MSG2,
EV_NEGO_SA-->QM_BLD_MSG2, EV_IS_REKEY-->QM_BLD_MSG2, EV_CONFIRM_SA-->QM_BLD_MSG2, EV_PROC_MSG-->QM_BLD_MSG2, EV_HASH_OK-->QM_BLD_MSG2, NullEvent-->QM_BLD_MSG2,
EV_COMP_HASH
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, sending delete/delete with reason message
Apr 17 22:48:21 [IKEv1]Group = DefaultRAGroup, IP = 209.171.88.81, Removing peer from correlator table failed, no match!
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, IKE SA MM:d8870fa5 rcv'd Terminate: state MM_ACTIVE flags 0x00000042, refcnt 1, tuncnt 0
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, IKE SA MM:d8870fa5 terminating: flags 0x01000002, refcnt 0, tuncnt 0
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, sending delete/delete with reason message
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing blank hash payload
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing IKE delete payload
Apr 17 22:48:21 [IKEv1 DEBUG]Group = DefaultRAGroup, IP = 209.171.88.81, constructing qm hash payload
Apr 17 22:48:21 [IKEv1]IP = 209.171.88.81, IKE_DECODE SENDING Message (msgid=232654dc) with payloads : HDR + HASH (8) + DELETE (12) + NONE (0) total length : 80
Apr 17 22:48:21 [IKEv1]Group = DefaultRAGroup, IP = 209.171.88.81, Session is being torn down. Reason: Phase 2 Mismatch
I am new to this so I don't know what I should do next. Thanks

Here it is. Thanks.
CL-T179-12IH# show run crypto
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA ESP-3DES-SHA ESP-DES-SHA ESP-AES-128-SHA-TRANS ESP-AES-192-SHA-TRANS ESP-AES-256-SHA-TRANS ESP-3DES-SHA-TRANS ESP-DES-SHA-TRANS
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint vpn
enrollment self
subject-name CN=174.142.90.17
crl configure
crypto ca trustpool policy
crypto ca certificate chain vpn
certificate 2d181c55
308201ff 30820168 a0030201 0202042d 181c5530 0d06092a 864886f7 0d010105
05003044 31163014 06035504 03130d31 37342e31 34322e39 302e3137 312a3028
06092a86 4886f70d 01090216 1b434c2d 54313739 2d313249 482e7072 69766174
65646e73 2e636f6d 301e170d 31353034 31363033 31393439 5a170d32 35303431
33303331 3934395a 30443116 30140603 55040313 0d313734 2e313432 2e39302e
3137312a 30280609 2a864886 f70d0109 02161b43 4c2d5431 37392d31 3249482e
70726976 61746564 6e732e63 6f6d3081 9f300d06 092a8648 86f70d01 01010500
03818d00 30818902 818100bf 797d1cc1 cfffc634 8c3b2a4b ce27b1c9 3fc3e026
4f6cd8f4 c9675aca b5176cef 7f3df142 35ba4e15 2613d34c 91bb5da3 14b34b6c
71e4ff44 f129046f 7f91e73f 2c9d42f9 93001559 ea6c71c1 1a848073 15da79f7
a41081ee b4cd3cc3 baa7a272 3a5fb32d 66dedee6 5994d4b2 ad9d7489 44ec9eb9
44038a2a 817e935f 1bb7ad02 03010001 300d0609 2a864886 f70d0101 05050003
8181002c 6cee9ae7 a037698a 5690aca1 f01c87db 04d9cbc6 65bda6dc a17fc4b6
b1fd419e 56df108f b06edfe6 ab5a5eb3 5474a7fe 58970da3 23e6bc6e 36ab8f62
d5c442bf 43581eb3 26b8cf26 6a667a8b ddd25a73 a094f0d0 65092ff8 d2a644d8
3d7da7ca efeb9e2f 84807fdf 0cf3d75e bcb65ba4 7b51cb49 f912f516 f95b5d86
da0e01
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint vpn
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400

Cisco Jabber Client for Windows 9.7 Can't Connect to Other IPSec VPN Clients Over Clustered ASAs

Environment:
2 x ASA 5540s (at two different data centers) configured as a VPN Load Balancing Cluster
Both ASAs are at version 8.4(5)6
IPSec VPN Client version: 5.0.07.440 (64-bit)
Jabber for Windows v9.7.0 build 18474
Issue:
If I am an IPSec VPN user…
I can use Jabber to another IPSec VPN user that is connected to the same ASA appliance.
I can’t use Jabber to another IPSec VPN user that is connected to the different ASA appliance that I am connected to.
In the hub-and-spoke design, where the VPN ASA is a hub, and the VPN client is a spoke; if you have two hubs clustered together, how does one spoke communicate with another spoke on the other hub in the cluster? (How to allow hairpinning to the other ASA)

Portu,
Thanks for your quick reply.
Unfortunately, I do not have access to the ASA logs nor would I be permitted to turn on the debug settings asked for above. I might be able to get the logs but it will take awhile and I suspect they wouldn't be helpful as this ASA supports thousands of clients, therefore, separating out my connection attempts from other clients would be difficult.
I can, though, do whatever you want on the Linux router. Looking over the firewall logs at the time of this problem, I don't see anything that looks suspicious such as dropped packets destined for the Windows client.
As I said in my original post, I'm not a networking expert - by any means - but I am willing to try anything to resolve this. (But I might need a bit of handholding if I need to set up a wireshark andor tcpdump.)
Thanks again.

Cisco Jabber Client for Windows 9.7 Can't Connect IPSec VPN Clients over two ASAs

Environment:
2 x ASA 5540s (at two different data centers) configured as a VPN Load Balancing Cluster
Both ASAs are at version 8.4(5)6
IPSec VPN Client version: 5.0.07.440 (64-bit)
Jabber for Windows v9.7.0 build 18474
Issue:
If I am an IPSec VPN user…
I can use Jabber to another IPSec VPN user that is connected to the same ASA appliance.
I can’t use Jabber to another IPSec VPN user that is connected to the different ASA appliance that I am connected to.
In the hub-and-spoke design, where the VPN ASA is a hub, and the VPN client is a spoke; if you have two hubs clustered together, how does one spoke communicate with another spoke on the other hub in the cluster? (How to allow hairpinning to the other ASA)

Portu,
Thanks for your quick reply.
Unfortunately, I do not have access to the ASA logs nor would I be permitted to turn on the debug settings asked for above. I might be able to get the logs but it will take awhile and I suspect they wouldn't be helpful as this ASA supports thousands of clients, therefore, separating out my connection attempts from other clients would be difficult.
I can, though, do whatever you want on the Linux router. Looking over the firewall logs at the time of this problem, I don't see anything that looks suspicious such as dropped packets destined for the Windows client.
As I said in my original post, I'm not a networking expert - by any means - but I am willing to try anything to resolve this. (But I might need a bit of handholding if I need to set up a wireshark andor tcpdump.)
Thanks again.

Inbuilt cisco IPSEC vpn client and KeyLife Timeout setting...

Hi Guys
I am having issues with the in built cisco vpn client on the mac, I am currrently using Mac OSx 10.7.4
I have a Fortigate 200B device and have setup the IPSec VPN settings to have a keylife of 86400 seconds.
However the expereince I am having with the mac clients is that after about 50 minutes the users are being asked to re-authencate to the VPN...
When checkin the debug logs I can see that the peer (mac client) is setting the phase 2 tunnel key lifetime to 3600 seconds which is 1 Hour...
Usually in IPSec a re-negeotiation process takes place about 10 minutes or so before the key expires..
My question is where are the VPN settings kept in the Mac... I know it uses Racoon for the IPSec exchange of key and so I would like to tweak the VPN profiles so that the mac sets the lifetime of the key to 86400 instead of 3600 by default...
Also want to be able to set logging to debug mode for the Racoon application on mac clients.
Your help is much appreciated
Kind Regards
Mohamed

Hi Tony,
to the best of my knowledge this is currently not possible, but will be once this enhancement is implemented:
CSCsw31922 Radius upstream VSAs (Tunnel Group,Client type) for VPN policy decisions
You may want to try and ask in the AAA forum if there is anything you can do on ACS...
hth
Herbert

Setting up IPsec VPNs to use with Cisco Anyconnect

So I've been having trouble setting up vpns on our ASA 5510. I would like to use IPsec VPNs so that we don't have to worry about licensing issues, but from what I've read you can do this with and still use Cisco Anyconnect. My knowledge on how to set up VPNs especially in iOS verion 8.4 is limited so I've been using a combination of command line and ASDM.
I'm finally able to connect from a remote location but once I connect, nothing else works. From what I've read, you can use IPsec for client-to-lan connections. I've been using a preshared key for this. Documentation is limited on what should happen after you connect? Shouldn't I be able to access computers that are local to the vpn connection? I'm trying to set this up from work. If I VPN from home, shouldn't I be able to access all resources at work? I think because I've used the command line as well as ASDM I've confused some of the configuration. Plus I think some of the default policies are confusing me too. So I probably need a lot of help. Below is my current configuration with IP address altered and stuff that is completely non-related to vpns removed.
NOTE: We are still testing this ASA and it isn't in production.
Any help you can give me is much appreciated.
ASA Version 8.4(2)
hostname ASA
domain-name domain.com
interface Ethernet0/0
nameif inside
security-level 100
ip address 192.168.0.1 255.255.255.0
interface Ethernet0/1
nameif outside
security-level 0
ip address 50.1.1.225 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
no nameif
security-level 100
ip address 192.168.1.1 255.255.255.0
boot system disk0:/asa842-k8.bin
ftp mode passive
dns domain-lookup outside
dns server-group DefaultDNS
same-security-traffic permit intra-interface
object network NETWORK_OBJ_192.168.0.224_27
subnet 192.168.0.224 255.255.255.224
object-group service VPN
service-object esp
service-object tcp destination eq ssh
service-object tcp destination eq https
service-object udp destination eq 443
service-object udp destination eq isakmp
access-list ips extended permit ip any any
ip local pool VPNPool 192.168.0.225-192.168.0.250 mask 255.255.255.0
no failover
failover timeout -1
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.0.224_27 NETWORK_OBJ_192.168.0.224_27 no-proxy-arp route-lookup
object network LAN
nat (inside,outside) dynamic interface
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 50.1.1.250 1
sysopt noproxyarp inside
sysopt noproxyarp outside
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ASA
crl configure
crypto ca server
shutdown
crypto ca certificate chain ASDM_TrustPoint0
certificate d2c18c4e
    308201f3 3082015c a0030201 020204d2 c18c4e30 0d06092a 864886f7 0d010105
    0500303e 3110300e 06035504 03130741 53413535 3130312a 30280609 2a864886
    f70d0109 02161b41 53413535 31302e64 69676974 616c6578 7472656d 65732e63
    6f6d301e 170d3131 31303036 31393133 31365a17 0d323131 30303331 39313331
    365a303e 3110300e 06035504 03130741 53413535 3130312a 30280609 2a864886
    f70d0109 02161b41 53413535 31302e64 69676974 616c6578 7472656d 65732e63
    6f6d3081 9f300d06 092a8648 86f70d01 01010500 03818d00 30818902 818100b2
    8acbe1f4 5aa19dc5 d3379bf0 f0e1177d 79b2b7cf cc6b4623 d1d97d4c 53c9643b
    37f32caf b13b5205 d24457f2 b5d674cb 399f86d0 e6c3335f 031d54f4 d6ca246c
    234b32b2 b3ad2bf6 e3f824c0 95bada06 f5173ad2 329c28f8 20daaccf 04c51782
    3ca319d0 d5d415ca 36a9eaff f9a7cf9c f7d5e6cc 5f7a3412 98e71de8 37150f02
    03010001 300d0609 2a864886 f70d0101 05050003 8181009d d2d4228d 381112a1
    cfd05ec1 0f51a828 0748172e 3ff7b480 26c197f5 fd07dd49 01cd9db6 9152c4dc
    18d0f452 50f5d0f5 4a8279c4 4c1505f9 f5e691cc 59173dd1 7b86de4f 4e804ac6
    beb342d1 f2db1d1f 878bb086 981536cf f4094dbf 36c5371f e1a0db0a 75685bef
    af72e31f a1c4a892 d0acc618 888b53d1 9b888669 70e398
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside client-services port 443
crypto ikev2 remote-access trustpoint ASDM_TrustPoint0
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 10
console timeout 0
management-access inside
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2
anyconnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3
anyconnect profiles VPN disk0:/devpn.xml
anyconnect enable
tunnel-group-list enable
group-policy VPN internal
group-policy VPN attributes
wins-server value 50.1.1.17 50.1.1.18
dns-server value 50.1.1.17 50.1.1.18
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-client
default-domain value digitalextremes.com
webvpn
anyconnect profiles value VPN type user
always-on-vpn profile-setting
username administrator password xxxxxxxxx encrypted privilege 15
username VPN1 password xxxxxxxxx encrypted
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool (inside) VPNPool
address-pool VPNPool
authorization-server-group LOCAL
default-group-policy VPN
tunnel-group VPN webvpn-attributes
group-alias VPN enable
tunnel-group VPN ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
class-map ips
match access-list ips
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect ip-options
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
inspect http
class ips
ips inline fail-open
class class-default
user-statistics accounting

Hi Marvin, thanks for the quick reply.
It appears that we don't have Anyconnect Essentials.
Licensed features for this platform:
Maximum Physical Interfaces       : Unlimited      perpetual
Maximum VLANs                     : 100            perpetual
Inside Hosts                      : Unlimited      perpetual
Failover                          : Active/Active perpetual
VPN-DES                           : Enabled        perpetual
VPN-3DES-AES                      : Enabled        perpetual
Security Contexts                 : 2              perpetual
GTP/GPRS                          : Disabled       perpetual
AnyConnect Premium Peers          : 2              perpetual
AnyConnect Essentials             : Disabled       perpetual
Other VPN Peers                   : 250            perpetual
Total VPN Peers                   : 250            perpetual
Shared License                    : Disabled       perpetual
AnyConnect for Mobile             : Disabled       perpetual
AnyConnect for Cisco VPN Phone    : Disabled       perpetual
Advanced Endpoint Assessment      : Disabled       perpetual
UC Phone Proxy Sessions           : 2              perpetual
Total UC Proxy Sessions           : 2              perpetual
Botnet Traffic Filter             : Disabled       perpetual
Intercompany Media Engine         : Disabled       perpetual
This platform has an ASA 5510 Security Plus license.
So then what does this mean for us VPN-wise? Is there any way we can set up multiple VPNs with this license?

Need help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 8.2(1)

Need urgent help in configuring Client to Site IPSec VPN with Hairpinning on Cisco ASA5510 - 8.2(1).
The following is the Layout:
There are two Leased Lines for Internet access - 1.1.1.1 & 2.2.2.2, the latter being the Standard Default route, the former one is for backup.
I have been able to configure Client to Site IPSec VPN
1) With access from Outside to only the Internal Network (172.16.0.0/24) behind the asa
2) With Split tunnel with simultaneous assess to internal LAN and Outside Internet.
But I have not been able to make tradiotional Hairpinng model work in this scenario.
I followed every possible sugestions made in this regard in many Discussion Topics but still no luck. Can someone please help me out here???
Following is the Running-Conf with Normal Client to Site IPSec VPN configured with No internat Access:
LIMITATION: Can't Boot into any other ios image for some unavoidable reason, must use 8.2(1)
running-conf --- Working normal Client to Site VPN without internet access/split tunnel
ASA Version 8.2(1)
hostname ciscoasa
domain-name cisco.campus.com
enable password xxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxxxxx encrypted
names
interface GigabitEthernet0/0
nameif internet1-outside
security-level 0
ip address 1.1.1.1 255.255.255.240
interface GigabitEthernet0/1
nameif internet2-outside
security-level 0
ip address 2.2.2.2 255.255.255.224
interface GigabitEthernet0/2
nameif dmz-interface
security-level 0
ip address 10.0.1.1 255.255.255.0
interface GigabitEthernet0/3
nameif campus-lan
security-level 0
ip address 172.16.0.1 255.255.0.0
interface Management0/0
nameif CSC-MGMT
security-level 100
ip address 10.0.0.4 255.255.255.0
boot system disk0:/asa821-k8.bin
boot system disk0:/asa843-k8.bin
ftp mode passive
dns server-group DefaultDNS
domain-name cisco.campus.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network cmps-lan
object-group network csc-ip
object-group network www-inside
object-group network www-outside
object-group service tcp-80
object-group service udp-53
object-group service https
object-group service pop3
object-group service smtp
object-group service tcp80
object-group service http-s
object-group service pop3-110
object-group service smtp25
object-group service udp53
object-group service ssh
object-group service tcp-port
object-group service udp-port
object-group service ftp
object-group service ftp-data
object-group network csc1-ip
object-group service all-tcp-udp
access-list INTERNET1-IN extended permit ip host 1.2.2.2 host 2.2.2.3
access-list CSC-OUT extended permit ip host 10.0.0.5 any
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq www
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq https
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ssh
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq ftp
access-list CAMPUS-LAN extended permit udp 172.16.0.0 255.255.0.0 any eq domain
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq smtp
access-list CAMPUS-LAN extended permit tcp 172.16.0.0 255.255.0.0 any eq pop3
access-list CAMPUS-LAN extended permit ip any any
access-list csc-acl remark scan web and mail traffic
access-list csc-acl extended permit tcp any any eq smtp
access-list csc-acl extended permit tcp any any eq pop3
access-list csc-acl remark scan web and mail traffic
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 993
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq imap4
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq 465
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq www
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq https
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq smtp
access-list INTERNET2-IN extended permit tcp any host 1.1.1.2 eq pop3
access-list INTERNET2-IN extended permit ip any host 1.1.1.2
access-list nonat extended permit ip 172.16.0.0 255.255.0.0 172.16.0.0 255.255.0.0
access-list DNS-inspect extended permit tcp any any eq domain
access-list DNS-inspect extended permit udp any any eq domain
access-list capin extended permit ip host 172.16.1.234 any
access-list capin extended permit ip host 172.16.1.52 any
access-list capin extended permit ip any host 172.16.1.52
access-list capin extended permit ip host 172.16.0.82 host 172.16.0.61
access-list capin extended permit ip host 172.16.0.61 host 172.16.0.82
access-list capout extended permit ip host 2.2.2.2 any
access-list capout extended permit ip any host 2.2.2.2
access-list campus-lan_nat0_outbound extended permit ip 172.16.0.0 255.255.0.0 192.168.150.0 255.255.255.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu internet1-outside 1500
mtu internet2-outside 1500
mtu dmz-interface 1500
mtu campus-lan 1500
mtu CSC-MGMT 1500
ip local pool vpnpool1 192.168.150.2-192.168.150.250 mask 255.255.255.0
ip verify reverse-path interface internet2-outside
ip verify reverse-path interface dmz-interface
ip verify reverse-path interface campus-lan
ip verify reverse-path interface CSC-MGMT
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-621.bin
no asdm history enable
arp timeout 14400
global (internet1-outside) 1 interface
global (internet2-outside) 1 interface
nat (campus-lan) 0 access-list campus-lan_nat0_outbound
nat (campus-lan) 1 0.0.0.0 0.0.0.0
nat (CSC-MGMT) 1 10.0.0.5 255.255.255.255
static (CSC-MGMT,internet2-outside) 2.2.2.3 10.0.0.5 netmask 255.255.255.255
access-group INTERNET2-IN in interface internet1-outside
access-group INTERNET1-IN in interface internet2-outside
access-group CAMPUS-LAN in interface campus-lan
access-group CSC-OUT in interface CSC-MGMT
route internet2-outside 0.0.0.0 0.0.0.0 2.2.2.5 1
route internet1-outside 0.0.0.0 0.0.0.0 1.1.1.5 2
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication enable console LOCAL
http server enable
http 10.0.0.2 255.255.255.255 CSC-MGMT
http 10.0.0.8 255.255.255.255 CSC-MGMT
http 1.2.2.2 255.255.255.255 internet2-outside
http 1.2.2.2 255.255.255.255 internet1-outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group5
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map internet2-outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map internet2-outside_map interface internet2-outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca xyzxyzxyzyxzxyzxyzxyzxxyzyxzyxzy
        a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as a67a897as
    a67a897as a67a897as a67a897as a67a897as a67a897as
quit
crypto isakmp enable internet2-outside
crypto isakmp policy 10
authentication pre-share
encryption aes
hash md5
group 2
lifetime 86400
telnet 10.0.0.2 255.255.255.255 CSC-MGMT
telnet 10.0.0.8 255.255.255.255 CSC-MGMT
telnet timeout 5
ssh 1.2.3.3 255.255.255.240 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet1-outside
ssh 1.2.2.2 255.255.255.255 internet2-outside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy VPN_TG_1 internal
group-policy VPN_TG_1 attributes
vpn-tunnel-protocol IPSec
username ssochelpdesk password xxxxxxxxxxxxxx encrypted privilege 15
username administrator password xxxxxxxxxxxxxx encrypted privilege 15
username vpnuser1 password xxxxxxxxxxxxxx encrypted privilege 0
username vpnuser1 attributes
vpn-group-policy VPN_TG_1
tunnel-group VPN_TG_1 type remote-access
tunnel-group VPN_TG_1 general-attributes
address-pool vpnpool1
default-group-policy VPN_TG_1
tunnel-group VPN_TG_1 ipsec-attributes
pre-shared-key *
class-map cmap-DNS
match access-list DNS-inspect
class-map csc-class
match access-list csc-acl
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class csc-class
csc fail-open
class cmap-DNS
inspect dns preset_dns_map
service-policy global_policy global
prompt hostname context
Cryptochecksum: y0y0y0y0y0y0y0y0y0y0y0y0y0y
: end
Neither Adding dynamic NAT for 192.168.150.0/24 on outside interface works, nor does the sysopt connection permit-vpn works
Please tell what needs to be done here, to hairpin all the traffic to internet comming from VPN Clients.
That is I need clients conected via VPN tunnel, when connected to internet, should have their IP's NAT'ted against the internet2-outside interface address 2.2.2.2, as it happens for the Campus Clients (172.16.0.0/16)
I'm not much conversant with everything involved in here, therefore please be elaborative in your replies. Please let me know if you need any more information regarding this setup to answer my query.
Thanks & Regards
maxs

Hi Jouni,
Thanks again for your help, got it working. Actually the problem was ASA needed some time after configuring to work properly ( ?????? ). I configured and tested several times within a short period, during the day and was not working initially, GUI packet tracer was showing some problems (IPSEC Spoof detected) and also there was this left out dns. Its working fine now.
But my problem is not solved fully here.
Does hairpinning model allow access to the campus LAN behind ASA also?. Coz the setup is working now as i needed, and I can access Internet with the NAT'ed ip address (outside-interface). So far so good. But now I cannot access the Campus LAN behind the asa.
Here the packet tracer output for the traffic:
packet-tracer output
asa# packet-tracer input internet2-outside tcp 192.168.150.1 56482 172.16.1.249 22
Phase: 1
Type: ACCESS-LIST
Subtype:
Result: ALLOW
Config:
Implicit Rule
Additional Information:
MAC Access list
Phase: 2
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   172.16.0.0      255.255.0.0     campus-lan
Phase: 4
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   192.168.150.1   255.255.255.255 internet2-outside
Phase: 5
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group internnet1-in in interface internet2-outside
access-list internnet1-in extended permit ip 192.168.150.0 255.255.255.0 any
Additional Information:
Phase: 6
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 7
Type: CP-PUNT
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 8
Type: VPN
Subtype: ipsec-tunnel-flow
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: NAT-EXEMPT
Subtype: rpf-check
Result: ALLOW
Config:
Additional Information:
Phase: 10
Type: NAT
Subtype:
Result: DROP
Config:
nat (internet2-outside) 1 192.168.150.0 255.255.255.0
match ip internet2-outside 192.168.150.0 255.255.255.0 campus-lan any
    dynamic translation to pool 1 (No matching global)
    translate_hits = 14, untranslate_hits = 0
Additional Information:
Result:
input-interface: internet2-outside
input-status: up
input-line-status: up
output-interface: internet2-outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
The problem here as you can see is the Rule for dynamic nat that I added to make hairpin work at first place
dynamic nat
asa(config)#nat (internet2-outside) 1 192.168.150.0 255.255.255.0
Is it possible to access both
1)LAN behind ASA
2)INTERNET via HAIRPINNING
simultaneously via a single tunnel-group?
If it can be done, how do I do it. What changes do I need to make here to get simultaneous access to my LAN also?
Thanks & Regards
Abhijit

WRVS4400N IPSec VPN Advanced Settings Found

Similar Messages

Maybe you are looking for