WRVS4400N v1 Router with 3 WRT600N (Access Points) locks Internet access

Have the following equipment
1.  WRVS4400N  (DHCP Services and connected to DSL modem on different subnets, QuickVPN enabled but not working)
2.  3 WRT600N used as Access Points troughout the house  connected to the ports on the above router
The problem is that after working for a while the internet access locks out....  although the wireless laptops get an IP address and can see other network equipment they can't access the internet.  After a restart on the WRVS4400N everything works again.
If I connect to one of the ports on the DSL everything is always working.  So what could be causing the problem?  I don't want the client to have to restart the WRVS4400n router every day.
Any ideas?

Please update the WRVS4400N v1 to the latest code. The  new code fixes some of the DHCP issues
http://tools.cisco.com/support/downloads/go/PlatformList.x?sftType=Wireless+Router+Firmware&mdfid=282446893&treeName=Routers&mdfLevel=Model&url=null&modelName=Cisco+WRVS4400N+Wireless-N+Gigabit+Security+Router+-+VPN+V1.0+%26+V1.1&isPlatform=N&treeMdfId=268437899&modifmdfid=null&imname=&hybrid=Y&imst=N

Similar Messages

  • How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    How can I set up a guest access point with a Time Capsule and an Airport Extreme? I am using a Telus router with the Time Capsule used as a wireless access point (bridge mode). I don't want the guest access point to have access to my network.

    The Guest Network function of the Time Capsule and AirPort Extreme cannot be enabled when the device is in Bridge Mode. Unfortunately, with another router...the Telus...upstream on your network, Bridge Mode is indicated as the correct setting for all other routers on the network.
    If you can replace the Telus gateway with a simple modem (that performs no routing functions), you should be able to configure either the Time Capsule or the AirPort Extreme....whichever is connected to the modem....to provide a Guest Network.

  • IMac as a wireless access point to internet

    Hi anyone knows iMac as a access point to internet to use other gadgets

    Check out System Preferences > Sharing > Internet Sharing
    If your iMac is connected to your broadband modem with an Ethernet cable, you can share access to it via WiFi.
    If your iMac is connected to your broadband modem with Airport Wifi, you can share access by plugging a device into the iMac via Ethernet cable.
    So yes, you can share the access by Ethernet cable or WiFi, one or the other. Not both simultaneously.

  • Connected to access point but internet cannot be found????

    router was working fine until it wasnt finding internet one nite and then it was unplugged so internet could be used on main computer and now when i try to plug everything back up to get wireless internet, it still says connected to access point but internet not found dont have a clue what is going on!?!

    I think you were connecting to wireless router to access Internet, you need to have proper configuration on wireless router and wireless adapter to make it work, take a look on this wireless network setup tutorial to help you.

  • Is it possible to be connected with a 3G modem for internet access and a WiFi router for printer sharing at the same time?

    For our only internet access we have a 3G wireless modem. I have since purchased a WiFi printer and router to connect all the comptuters to in the house. The PCs have no problem with using both the 3G connection and the WiFi signal at the same time to print, however, the MacBook Pro will not connect to the 3G network and the router, it will drop the internet access from the modem and attempt to connect via WiFi (which has no internet access). Is there a solution that is available to remedy this? I attempted to create an adhoc printer network, however, the macbooks again will not print off of this, only the PCs. And I'm getting a bit frustrated overall with this.

    The 3G wireless modem is on one of the PC's correct?
    Why don't you pass the Internet through the Ethernet port to the router via Cat5 cable, then have that transmit a Wifi signal that everything else can use, then connect the printer to the router for print sharing?
    You would have to turn off the wifi on the comptuer with the 3G modem as it's physically connected to the router and can't connect to the other machines as they are all connected to the router for sharing.
    The Mac has the ability to pass, Internet Sharing in the System Preferences.
    Do you have software for the Mac to run the 3G modem?

  • IOS 6, Netgear access point and Internet

    Hi,
    I’ve reached a point where I’m not entirely sure what to do next.
    Here are some quick details (all are on most recent firmware unless stated):
    Router: Draytek Vigor2830n
    Access Point: Netgear WG102
    Devices: iPhone 4, iPhone 5, iPad 2 and two iPad 2’s for comparison on iOS 5.
    So, all devices running iOS 6.1.3/4 will connect to the Netgear access point just fine, can browse the LAN / stream media from network shares but internet access seems to be 'delayed' and can take anywhere between a minute to 20 minutes to connect (I give up after this). In comparison both the iPad 2’s running iOS 5 will gain internet access immediately after connecting to the access point.
    On the other hand, when connecting to the routers wireless on all devices it works flawlessly and internet connection is 'instant'.
    Given the problems that Netgear wifi has had with iOS 6, which were supposedly ‘fixed’ in iOS 6.1, I’m not sure what to do. It’s definitely a software problem, and could well be something to do with the router (along with connecting to the access point and iOS 6), but I’m not sure what to start changing first. iOS 5 works fine, so what has changed in iOS 6 to break it?
    Its not a security issue like before 6.1 and not being able to connect to the access point at all.
    Basically:
    - I either need to figure what in iOS 6 is causing this ‘delay’ and how to fix it
    -Give up on the access point and buy a new one (seems a bit extreme given that every other devices works fine – iOS 5, blackberry, laptops etc).
    -Wait for iOS 7, hopefully in the next couple of weeks and see if it fixes it, though I can find little information on this issue as it is, and nothing to suggest iOS 7 might help. Though if iOS 5 is fine, iOS 6 broke it and 6.1 slightly fixed it, maybe iOS 7 will cure it? Doubt it…but worth waiting a few days.
    Anyone got any suggestions? I have been through all the usual (HTTP proxy, forget this network, reset network settings), nothing makes it work flawlessly like iOS 5 and the issue is the same on a wide spread of devices running iOS 6.

    Dont know my routerand access point works fine. Try http://support.apple.com/kb/HT4199 and make sure your setting are correct.

  • Setting up access points for public access

    Okay, here's the situation. I have a PowerMac G4/1.25GHz dual processor running Server X 10.3.9 with four Mac clients (a small law office). Up until recently, everyone had also been running (client) 10.3.9, but I started upgrading some of them to 10.4 (currently 10.4.5). When I did this, they started running into problems with Word sometimes giving a "network or file permission error" when attempting to save documents to the server. After weeks of posting questions to Word support and trying everything in the book that I could think of, I found Apple recently posted what appears to be the answer to this (article 302979, "Microsoft Office applications fail to save to a server volume." The problem? I have all four users logging into the same account on the server, and when one of them logs out, it zaps everything in a Microsoft-created temp folder on the server, including temp files created by open documents created by other clients. Sheesh.
    I had everyone set to use the same account because they have no need of document security -- everyone should be able to get into everyone else's files on the server, period. So, because of this snafu, I've created separate accounts for each of the users. My problem now is that, if user "X" creates a file or folder on the server, user "Y" cannot modify it because it is created as read-only. Strangely, if someone modifies an existing file, it doesn't change the user rights at all -- not sure why.
    I'll admit to being a bit of a novice with Server X but am familiar with parent/child folder permissions -- I think I've got everything set right, but I must obviously be missing something. Here's what I've got setup, and what I've tried. If anyone can point out how I've got this setup improperly, I really need to get this fixed... thanks.
    I have a single sharepoint ("workfiles"). I used the "public" folder as an example, and set the owner to "root" and the group to "staff". Further, I set the owner, group and everyone privileges to "read & write". I've also tried setting the group to "admin". All the individual user accounts I've set are also setup as admin users. I've tried setting each users's primary group as "staff (20)" or "admin (80)". I've copied all these privileges to all enclosed items, which does reset everything to public access, but as soon as someone creates a new folder or file, that folder/file becomes private to that user (it shows up with the creator's username as "owner" (r&w), group as "admin (read-only), and others as "read-only" as well.
    PS: If upgrading the server to Server X 10.4 would help, I'm sure I can arrange that.

    In our law firm, the server (10.4.4), we have set access to read/write access so staff can open client files/folders, edit then and close, etc. That seems to be working okay. Before the tech worked on permissions, if someone created a letter another staff member could open it, but it was read-only.
    The problem we are having is that if a file that is clicked on stationery pad and we want to edit it, it will not allow us to. For example, if we need to edit our letterhead that normally comes up as an untitled document, if I unclick the stationery pad box, it unclicks, but it still comes up as an untitled document. I even tried to unclick a stationery pad on a document that I created before the server upgrade and it wouldn't let me.
    If I create a brand new document and put it on stationery pad, it comes up untitled as it should. If another user on another desktop wants to make changes, they unclick the stationery pad box, but when they open it, it comes up untitled and in checking get info, the stationery pad is selected.
    The tech set it up as follows:
    Share Points and All tabs:
    General tab: box to share this item and its contents is clicked
    Access tab: owner, group and everyone have read/write privileges
    If select dial at bottom to propagate permissions, all boxes are checked, except for access control list, which is shaded.
    I cannot drag/add anything to the control list and the pencil and the minus sign is shaded
    Protocol tab: Both boxes, share item using AFP and Allow AFP guest users are clicked. But for better security in reading the article, this should be unchecked.
    Also under the protocol tab: the inherit permission from parent radio dial is clicked, not the use standard POSIX behavior.
    What are we missing?
    Thanks, Cheryl

  • How to restore with no way of getting internet access

    I have an old 4s. I want to delete all content and restore as new. when i try to do that on the phone it asks me to enter my icloud password. I do that but it does to recognize it because i dont have any internet access. I cant turn wifi on because the button is grayed out.
    I deleted the phone from find iphone but that didnt work. It still appears on my iphone and itunes still shows it as on.
    I cant delete icloud account from that phone for the same reason.

    What happens when trying to restore the iPhone with iTunes on your computer? You are promoted to turn the iCloud account off on the iPhone with the iPhone only - no prompt for the password on your computer with iTunes when trying to restore the iPhone?

  • WRT54G ver. 6 Connected to access point and internet, but cannot access the web

    I can connect to the access point and it shows that I an connected to the internet.  However when I open a bowser it says page cannot be displayed!  Signal is very good to excellent.  Also, I have been using it all day and it was working fine, until I shutdown.  When I booted back up it stopped working.  The internet is working!  I have XBOX Live working right now.  Just not the computer.  Any Help would be appreciated.
    WRT54G ver. 6
    Message Edited by SJohnson4 on 12-01-200607:35 PM

    Hi... it seems that your Wireless adapter on does get a IP address or DNS no after reboot. Try assigning a Static IP address and DNS on the Wireless Adapter. Also try to update the drivers for that wireless adapter.

  • HT4437 Can you use airplay to stream from an iPad to a TV with a network connection without internet access

    Can you use airplay to stream from an iPad to a TV with a network connection without internet access

    Yes, you can use a network storage device for the storage of your content and use it on the Apple TV, but only as part of your iTunes library. So if your question is whether or not you can do this without using your computer or iTunes the answer is no.

  • "No Internet Access" indicator, but internet access works

    We've got a few machines at a couple different clients that have the windows networking systray exclamation mark indicating limited network connectivity.  The supposed error is "no internet access", though the internet works fine in every
    case.  It is a very visible issue generating a lot of complaints, and the clients have a tendency to associate it with all kinds of other unrelated problems.
    To clarify:
    Not all machines have the icon
    Problem machines all have the same basic setup as non-problem machines
    Some problem machines are win8, some win7
    They don't share common hardware specs
    I have tried several things, including:  reset ip stack, give manual ip settings to network adapter, disable ipv6, disable/re-enable adapter, all without success.
    I don't know where to go to troubleshoot this.  Is there a log with this info?  Is the network connectivity check process well documented somewhere?

    The issue occurs on ethernet and wireless.  I haven't been able to tell what the problem machines have in common.  The issue is basically permanent.  Sometimes an IP stack reset will "cure" the problem temporarily, but it returns.
    Here's an ipconfig /all from one of the trouble machines:
    Windows IP Configuration
       Host Name . . . . . . . . . . . . : XXXXXXX
       Primary Dns Suffix  . . . . . . . : klc.local
       Node Type . . . . . . . . . . . . : Hybrid
       IP Routing Enabled. . . . . . . . : No
       WINS Proxy Enabled. . . . . . . . : No
       DNS Suffix Search List. . . . . . : klc.local
    Wireless LAN adapter Wireless Network Connection 2:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . : 
       Description . . . . . . . . . . . : Microsoft Virtual WiFi Miniport Adapter
       Physical Address. . . . . . . . . : 24-77-03-9E-xx-x1
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
    Wireless LAN adapter Wireless Network Connection:
       Connection-specific DNS Suffix  . : klc.local
       Description . . . . . . . . . . . : Intel(R) Centrino(R) Ultimate-N 6300 AGN
       Physical Address. . . . . . . . . : 24-77-03-9E-xx-x2
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes
       Link-local IPv6 Address . . . . . : fe80::edb8:5d03:14cc:3f8d%13(Preferred) 
       IPv4 Address. . . . . . . . . . . : 10.100.30.105(Preferred) 
       Subnet Mask . . . . . . . . . . . : 255.255.255.0
       Lease Obtained. . . . . . . . . . : Tuesday, October 07, 2014 10:35:54 AM
       Lease Expires . . . . . . . . . . : Wednesday, October 08, 2014 12:08:32 AM
       Default Gateway . . . . . . . . . : 10.100.30.1
       DHCP Server . . . . . . . . . . . : 10.100.20.100
       DHCPv6 IAID . . . . . . . . . . . : 237270787
       DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-CA-29-8A-D0-67-E5-54-28-5C
       DNS Servers . . . . . . . . . . . : 10.100.20.100
       Primary WINS Server . . . . . . . : 10.100.20.100
       NetBIOS over Tcpip. . . . . . . . : Enabled
    Ethernet adapter Local Area Connection:
       Media State . . . . . . . . . . . : Media disconnected
       Connection-specific DNS Suffix  . : klc.local
       Description . . . . . . . . . . . : Intel(R) 82579LM Gigabit Network Connection
       Physical Address. . . . . . . . . : D0-67-E5-54-xx-xx
       DHCP Enabled. . . . . . . . . . . : Yes
       Autoconfiguration Enabled . . . . : Yes

  • Direct Access has no internet access

    Hi all,
    Hopefully some can help me with this issue that I have been struggling with for about a week now.
    I'm new to Direct Access so please bear with me
    I've setup a Server 2012 box and installed the Direct Access role.  The server is behind en edge device with 1 NIC.
    I've configured it and can connect up Windows 8.1 tablets successfully, both on the internal network and when connected externally.
    The problem I have is with internet access when they are connected externally and I've tried with Force Tunneling enabled and disabled (ideally for security reasons I'd like it enabled).
    We use a proxy server configured with a wpad file hosted on Server 2003.  This is published via DNS.
    Internet Explorer is configured to Auto Detect Internet Settings
    I can connect to any of our internally hosted websites, and also strangely enough, our main publically accessible web site.
    If I don't have Force Tunneling enabled then I get the following behavior
    I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
    I can connect to any website that has the same domain suffix as our domain
    I can use Firefox and connect to external websites if I say 'Direct Connection to Internet' or 'Use System Settings'
    If I use Force Tunneling then I get the following behavior:
    The network connection says it is 'limited' and the Direct Access connection says it has 'No Internet Access'
    I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
    I can connect to any website that has the same domain suffix as our domain
    I can't use Firefox and connect to external websites
    Does anyone know why this would be the case?
    Thanks

    Thanks for the responses, I managed to get this working by unticking the 'Auto Detect Settings' and manually entering the proxy server and port under the 'Proxy Settings' option
    It means that it doesn't read my wpad file but I can manage this way still through GP.
    Another problem that I've just encountered for no reason that I can see is this.
    I'm connected to my Domain, I pull the LAN cable and then it auto connects me to my wireless network.  It used to auto connect me to my Direct Access server but it doesn't anymore, it just says connecting.  If I reboot the tablet while on the wireless
    LAN and then log on with my Domain Credentials it'll connect me through to the Direct Access server.
    Why would it need a reboot?  Why has it stopped connecting straight away after detecting I'm no longer on the domain?

  • I have a problem with iCloud - i have great internet access at work, but slow internet access at home (less than 1MB/PS) and I use the full range of iCloud syncing facilities. How can i make my devices ONLY sync at work.. and not at home??

    As stated above, if i go out during the day, buy an app, download a song and take 20 photo's when i get home my devices will all take 30mins to sync before i can even browse websites or check my facebook at home.
    Can i set up my iCloud to only sync when i am on my work Wi-fi...?

    Welcome to the Apple Community.
    Not unless you stop it connecting to wifi at home.

  • Using Gigabit Adapter for intranet access, wireless for internet access

    I have a PowerMac G5 I have been using with a built-in wireless adapter for a couple of years. I also have a Windows PC with a wireless adapter as well. Both of these access the internet over my AirportExpress connected to a cable modem.
    I wanted to take advantage of the Gigabit adapter in the PowerMac for copying files directly between the computers, so today I installed a Gigabit card in the PC and connected the two through a Gigabit switch.
    Unfortunately, I can't seem to get either the Mac or the PC to get valid IP addresses, let alone talk with each other.
    Any idea what I need to do on the Mac to get it to use the gigabit adapter for intranet traffic? I am guessing whatever I do on the Mac I will need to also do on the PC.
    Thanks!
    Brian

    What you're trying to do is called 'dual homing', and it's not really supported by OS X's automatic network configuration, though 'Internet Sharing' is close.
    I'd avoid it if at all possible. Connect the computers and the cable modem to the Gigabit switch. If the switch doesn't have routing capability, you might need a router also, to provide DHCP and NAT services. This would save you a lot of grief compared to figuring out how to set up the Mac and Windows for dual-home operation.

  • What access point to use with O2?

    When I connect to the web I have the option to choose how I want to connect (so at home I'll use a WLAN). With O2 what access point are recommended on a postpay contract and does it vary depending on 3G or GPRS reception ?
    i.e. use O2 MobileWeb with 3G?
    Thanks,

    Generally "WEB" should be used with a standard access point i.e no proxies etc
    check the settings under menu>tools>settings>connection>access points
    open the access point you normally use and select options>advanced settings you can then see if any proxies have been added. If necessary delete both the proxy and port
    If clear leave as is and make sure your access point name is the default "02" type. Contact them for this.
    iPhone 5 32GB
    MacBook Pro Retina 15" Mac OS X Mountain Lion 10.8.4

Maybe you are looking for