WRVS4400N wireless client has no internet access, unless first connected via cable

Hello everyone,
I recently purchased a WRVS4400N security router and have got a strange problem with it. I set it up as my main router and connected two computers (a desktop and a server) using DHCP. They both work fine, internet is as fast as it should be, no problems whatsoever.
However, when I setup the Wifi SSID (whatever security options I use, same with open/wpa/wpa2) and connect my laptop to it. It is allocated a IP address and windows even says that there is an internet connection. As soon as I try to do anything though, I am dropped. Try to ping an outside server, failure and dropped. Open IE, failure and dropped. I cannot even access my local server connected by wire to the router.
If I connect the laptop via a cable to the router everything works, and it continues to work when I unplug it. So this means that right now I walk over to the router and plug my laptop in for 3 seconds before I unplug it and then use the wifi for a couple of hours without any problem. But as soon as I try to turn on my wireless Logitech SqueezeBox or wireless printer, they fail and take my laptop with it..
I have:
reset the router, used both firmware 2.0.2.1 and 2.0.1.3 and done a factory reset.
Tried to move the router close to the laptop, no difference.
Does anybody have an idea as to what my problem could be?
/thomas

Hi Dean,
No this isn't from a company. I bought it used from www.tradera.com (like ebay) . The seller tells me it worked fine for him and has agreed to refund me. Thank you for answering, I have worked with some cisco routers and firewalls before but this one really got me pulling my hair.
I take it from your response that this is a known error that is covered by warranty?
/thomas

Similar Messages

I tunes on my laptop will not find ipad wireless and I get error message if I connect via cable

Itunes on my toshiba laptop ( running Windows XP) does not see my ipad via wireless network at home. If I try to connect via usb cable I get an error message. I have tried re booting both laptop and ipad and have recently loaded new itunes version.
HELP PLEASE?

Check this article: http://support.apple.com/kb/TS3221

Direct Access has no internet access

Hi all,
Hopefully some can help me with this issue that I have been struggling with for about a week now.
I'm new to Direct Access so please bear with me
I've setup a Server 2012 box and installed the Direct Access role. The server is behind en edge device with 1 NIC.
I've configured it and can connect up Windows 8.1 tablets successfully, both on the internal network and when connected externally.
The problem I have is with internet access when they are connected externally and I've tried with Force Tunneling enabled and disabled (ideally for security reasons I'd like it enabled).
We use a proxy server configured with a wpad file hosted on Server 2003. This is published via DNS.
Internet Explorer is configured to Auto Detect Internet Settings
I can connect to any of our internally hosted websites, and also strangely enough, our main publically accessible web site.
If I don't have Force Tunneling enabled then I get the following behavior
I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
I can connect to any website that has the same domain suffix as our domain
I can use Firefox and connect to external websites if I say 'Direct Connection to Internet' or 'Use System Settings'
If I use Force Tunneling then I get the following behavior:
The network connection says it is 'limited' and the Direct Access connection says it has 'No Internet Access'
I can't use Internet Explorer to connect to any public websites though (google.com, yellowpages.com, etc).
I can connect to any website that has the same domain suffix as our domain
I can't use Firefox and connect to external websites
Does anyone know why this would be the case?
Thanks

Thanks for the responses, I managed to get this working by unticking the 'Auto Detect Settings' and manually entering the proxy server and port under the 'Proxy Settings' option
It means that it doesn't read my wpad file but I can manage this way still through GP.
Another problem that I've just encountered for no reason that I can see is this.
I'm connected to my Domain, I pull the LAN cable and then it auto connects me to my wireless network. It used to auto connect me to my Direct Access server but it doesn't anymore, it just says connecting. If I reboot the tablet while on the wireless
LAN and then log on with my Domain Credentials it'll connect me through to the Direct Access server.
Why would it need a reboot? Why has it stopped connecting straight away after detecting I'm no longer on the domain?

Time Capsule has no internet access

I was asked by a friend to trouble shoot her Time Capsule. She get's an ip address from the TC, but she get's no internet access. She directly connects her iMac to the cable modem, and gets the www, so it is not the ISP. I reset the TC to its factory default and reconfigured it from scratch. It flashes a green light on the front, and in airport utility, it's status is also green. However, Safari gives a no network connection error. I have also tested the patch cables. Both patch cables give internet access when directly connected between the iMac and the cable modem. It also creates a wireless network and clients can join, file share, and also receive an ip address. However, they cannot get internet access.
Any ideas? This TC is about 16 months old.

Did you reset the modem?
Push the reset button and power it off immediately. Pull the battery if it's easily accessible. Let it rest for at least 15-20 minutes. (Some ISP's take longer for their equipment at the headquarters to reset.)
Power off the rest of the network.
After the power down period, start the modem first and let it run by itself for 5 minutes. Then start the Time Capsule the same way. Finally start your computers one at a time.
You should be on the internet if your settings on the Time Capsule are correct.

Conneced to wireless router but no internet access via wireless

I don't recall the physical connections being directly attached to the router. The router in question is a Linksys WRT54G/GL/GS. My initial thought was since we rolled out Voip fairly recently one of our phones might have ganked the IP address, but that is not the case. Each of them have their own IP addresses and I don't see any conflicts. I am also able to ping the router and log into it remotely from my office, which is in a different city. Could it possibly be a firmware issue?

Hi Everyone,
One of my offices' routers is broadcasting but has no internet access. The office does have internet if you hardwire in but outside of that nothing has worked so far in regards to the WiFi. I have power cycled the router and modem to no avail and DHCP is enabled but no one can get online via WiFi. It seemed to just up and decide one morning that it was not going to allow internet access.
This topic first appeared in the Spiceworks Community

Hi. I'm trying to set-up the wireless access times in my Airport Utility. I need to enter the "Description" and the "MAC Address" of each wireless client before I assign access times. What are these? Thanks.

Hi. I'm trying to set-up the wireless access times in my Airport Utility. I need to enter the "Description" and the "MAC Address" of each wireless client before I assign access times. What are these? Thanks.

Let's say that an iPhone is one of the wireless clients that you want to allow access to the network.
The Description of this device is anything that you want to specify for easy identification purposes. For example, the Description might be something like......
Rex's iPhone
The MAC Address, also known as a Wi-Fi Address is a unique indentifiction number that is assigned to every device. The number will always follow this form:
xx : xx : xx : xx : xx : xx, where "x" could be a number or letter.
To find the MAC Address or Wi-Fi Address of an iPhone or iPad.....
On the Home screen.....
Tap Settings
Tap General
Tap About
Wi-Fi Address is the item that you want
If you have a Mac computer......you can find the MAC Address or Wi-Fi Address as follows:
Open System Preferences (gear icon on the dock)
Open Network
Click on Wi-Fi on the left
Click Advanced at the lower right
The Wi-Fi Address for the Mac is located at the bottom of the window
Other wireless devices usually have the MAC Address or Wi-Fi Address on the label on the back or bottom of the device

Hi - for some reason, my IPAD3 mail client has decided it can no longer connect to my Exchange server.

Hi - for some reason, my IPAD3 mail client has decided it can no longer connect to my Exchange server. It's worked like a charm for weeks. Any thoughts?
For the record, I've got a POP mail account that is working fine on the machine and the WIFI is up and running (Safari is loading fine).
Thanks

Hi Jim,
Your issue is the most FAQ in the forums, it is an ongoing problem with Tiger waiting to be fixed by Apple. Till then, forget your aliases and use either Command-K or from the Finder Go-->Connect to Server and enter the remote Mac's IP address to connect.
Also, Open Utilities-->Terminal and type lookupd -flushcache (Press Return) and reboot. Do this for both macs.
Macs running 9.x, Macs running 10.4.x, SGI workstations running Irix 6.5.x

My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either.

My Canon MX 922 does not scan. My printer is connected via cable. Wireless doesn't work either. I get an error message with multiple suggestions but none of them apply to my situation.
I am so dissatisfied with this printer. I'm sorry I got it from Amazon because now it is a hassle to return it. I will never buy another Canon.
The printer menus are confusing. I hate using it. I loved my previous Canon which finally stopped working after many years, that's why I purchased a newer Canon model. Never again. Stick with cameras.
Marcy Hotz

This note won't be as angry and frustrated as the last one...
Because I still had my old printer drivers and other applications on my hard drive, I think the application was trying to connect with the old printer. I deleted all the old stuff.
I also had several scanning applications on my drive which just confused me.
When I used the actual Canon MX922 application, I was able to scan but could only save as JPG, TIF or BMP (and one more, I forget which). So I did some research on the Canon site and found out how to save documents as PDF files using the Canon IJ Scan Utility.
It works now. So I'm satisfied, will keep this maching. I just had to take some time, sit down and focus on the problem.

T510 can connect to wireless but has no internet connectivity on working wifi's

Hi,
I have a T510 with an Intel agn wireless card. On some wifi (always G), it finds the access point. It gets the proper information from the router (proper gateway, dns, ip), but no internet connectivity. The router is working fine (checked by using other computers)
If you run the lower level intel diagnostic it fails on the ping.
If you look at the ipconfig, everything looks fine.
The sequence is attach to the access point (wep), it say internet connectivity for about 10 seconds then it says no internet access.
No Zone Alarm, No firewall running, No virus protection enabled.
thoughts?
The machine is 2 weeks old.
thanks,
stevew

I have reset my airport this was the second time i was toying with it all last night. I was able to get on the little website for our modem so I disabled that firewall and turned off it's wireless capabilities and a few other odds and ends. And then I redid all of airport. Now though I get an unresolved problem status with "Double NAT" it says and I quote that "This base station has a private IP address on it's ethernet WAN port. It is connected to a divece or network that is using Network Address Translation (NAT) to provide private IP Addresses. You should change your base station from using DHCP and NAT to bridge mode." I ignored it because it seemed to be working last night fine with all of our devices on at the same time. but then again last time I reset it, it worked fine for about 3 days and then went to it's old habits.

WRT54GL Wireless Router says "No Internet Access" or "Cannot find IP Server Address"

I tried setting up a home network with my above Linksys router and can't connect to the internet now. I have the ethernet cable from my DSL Modem hooked into the ethernet port on the back of the Router. In port one, I have a cable which attaches directly to my laptop as I was advised to use a cable for initial setup of my home wireless network. I was able to get into the router to set all the passphrases and wireless security settings, etc. My ISP is PPPoe and I have entered both the UserId and Password that my ISP provided. However, upon clicking on the wireless icon, my system states I am connected but the status screen shows "No internet access". I have no problem connecting to the Internet when the cable runs from my DSL modem into my computer, so it's something to do with the router blocking it now.
My ISP does not support my Linksys router, of course, and they tell me I need to contact the manufacturer telling me the router needs to be set up as a 'bridge" ??? There is no mention of anything like this in the manual and I do not know if there is a setting on the router that is somehow blocking my being able to get an internet connection. This is all still with cables attached. Again, I seem to be able to 'connect' to the wireless network but I now cannot get to the Internet thru the router...
Can anyone tell me what I am doing wrong? Thanks!

Thanks, I did try the step by step instructions and changing the internet type to DHCP but still unable to connect to the internet. Setting back to PPPoE type, the error message now continues to say it "cannot find the IP address of the PPPoE server." I have reset the router back to factory defaults and reset the security and setup settings to no avail. My ISP (Juno), after providing the connection type, login name and password, stated I need to contact the manufacturer of the router and ask that it needs to be set up as a "Bridge". ??? Does this sound familiar to anyone?
My modem is a DSL 2Wire. On it's homepage, there is a field called ATM Encapsulation that is set to "Bridged LLC" but I am not touching the settings of my modem for fear of messing up my internet connection altogether. It has to be some setting on the router, is all I can think of. On the Status page of my Linksys router where I try to connect to the internet, once PPPoE is selected, the blank IP address and Subnet Mask settings are zeroes and you cannot enter anything into those fields. (I was going to try entering the address of my modem just to test if that might work...)
This is very frustrating. Even tried the 30-30-30 solution I read elsewhere worked for someone. Nothing. Same error message. Once I hook the ethernet cable from my modem into my router, I no longer can access the internet because it keeps saying it cannot find the PPPoE IP address.

Can't get internet access unless I am at home...

I can't get internet access, use my navigation or get messages unless I am at home. I have tried everything, and don't know what else to do. Please HELP any suggestions would be appreciated! Thank you!

Hi nthompson77,
Welcome to BlackBerry Support Community Forums.
Do you have a data plan with your wireless provider that supports internet browsing and messaging?
If you do, is your signal uppercase or lowercase when you're having this issue? Have you tried reinserting your battery?
-FS
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!

WSUS For Clients With No Internet Access

This is more of a functional question than an issue.
Right now I have WSUS set to 'Store update files locally' and it works great. With an ever expanding number and size of updates, I don't have space to keep storing the necessary updates on my WSUS server.
If I set WSUS to 'Do not store update files locally', will my clients without internet access still be able to get updates? Many of my devices are behind firewalls that do not permit access to the internet in any form. I'm trying to avoid adding
storage if at all possible.
Thanks,
Brian

Correct, if you set WSUS to 'do not store update files locally', then your clients without internet access will not be able to access Microsoft Update to download the files without you creating a firewall exception. Which sounds like an awkward way to do
it.
(1) Are you on top of your regular maintenance with WSUS, ie, declining superseded updates, running Server Cleanup Wizard in the recommended order?
(2) Are you confident that the classification of updates being downloaded is appropriate and nothing un-needed (e.g drivers/absent OS) are being downloaded? Have you chosen to download the space-hogging express installation files?
(1) and (2) would be generally better practise then 'do not store updates locally', but if bandwidth is cheap or irrelevant for you, then perhaps you might be tempted to not store updates locally. In your situation where you have a reason to deny clients
internet access, it would seem like a lot of paperwork, and technical expertise, to only allow them internet access for updates. (plus, I'm not sure it's possible, just presume it would be)
What are your numbers? (size of WSUSContent, WSUSDatabase, space on drives?)

Can connect to wireless network but no internet access

I have a PC that runs on Windows Vista and a wireless network using Airport Extreme. My PC can connect to the wireless network but I cannot access the internet. Windows Network Diagnostics states that 'A problem with your network router or broadband modem might be preventing an internet connection'. There should be no problem with my modem as I can access internet using my powerbook. When I run airport utility on my PC, there is an error message that states that 'An error occurred while trying to access the Apple wireless device. Make sure your network connection is valid and try again', 'error -6753'.

I am glad you brought this up. I am having the same difficulty. I run an iMac OS X 10.5.6 with an intel processor and a parallel system to get me on the Windows side. When I try to access the internet using my Airport extreme I cannot access any sites and the internet explorer page pops up with "The page cannot be displayed and sends me to try the diagnose connection problems on the toolbar method. However I can see my base station and all looks fine with the information there. I can also access the internet from my mac side of the computer. It would be nice to use the Windows side to gain access to the net because I have programs for the windows side that need updating. Anyone out there have any suggestions?

All my apple device has no internet access after connect to my house's wifi.

After connecting my apple ipad to my wifi, it show that there is no internet access. But my laptop can connect it and also use my wifi with internet access. My router is Wireless-G. Why can't I use my wifi????

Hi nkarthikeyan ,
You're right, in the behind configuration, there aren't any NAT configured for the simple reason which's Firewall is on production on another site and users must to connect to our Intranet to working properly so until I found a solution, I do some tests only with one desktop located on site...
I tried to add this command on my configuration but when I do it, I lost connection with computer of my site of ZAG ...
ASA5505-ZAG(config)# nat (inside,outside) source dynamic any interface
Also, I tried this configuration but without success also :/
for no-nat
object network ZAG_L2L
subnet 10.90.0.0 255.255.255.0
object network Trafic_vpn_MainSite_L2L1
subnet 10.239.80.0 255.255.248.0
object network Trafic_vpn_MainSite_L2L2
subnet 10.239.88.0 255.255.248.0
nat (inside,outside) source static ZAG_L2L ZAG_L2L destination static Trafic_vpn_MainSite_L2L1 Trafic_vpn_MainSite_L2L1
nat (inside,outside) source static ZAG_L2L ZAG_L2L destination static Trafic_vpn_MainSite_L2L2 Trafic_vpn_MainSite_L2L2
And to finish my questions, can you explain me this point please :
Also you need to place your real ip address in interface ACL's instead of NATed ip address...
Thanks for your support !
I really appreciate it !

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC has been turned on (PC is connected via Ethernet cable, and has no wireless capability as far as I know). What gives? It works fine when the PC is off.

Out of the blue, my ITouch is unable to access my wireless network ONLY when my PC is on (the PC is connected via Ethernet cable, and has no wireless capabilities that I know of). What gives? When the PC is turned off, everything is totally fine. I\m stumped.

Does the iOS device connect to other networks?
Does the iOS device see the network?
Any error messages?
Do other devices now connect?
Did the iOS device connect before?
Try the following to rule out a software problem:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power off and then back on your router
.- Reset network settings: Settings>General>Reset>Reset Network Settings
- iOS: Troubleshooting Wi-Fi networks and connections
- Wi-Fi: Unable to connect to an 802.11n Wi-Fi network
I suspect a problem with your router. Try changing the security. First use no security as a test.
- iOS: Recommended settings for Wi-Fi routers and access points
- Restore from backup. See:
iOS: How to back up
- Restore to factory settings/new iOS device.
If still problem and it does not connect to any networks make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar

WRVS4400N wireless client has no internet access, unless first connected via cable

Similar Messages

Maybe you are looking for