WS Adapter(PI 7.1) vs SOAManager? PI 7.4 Single Stack capabilities for WS-RM

Hi Experts,
The dual-stack SAP PI came with WS Adapter had the Direct communication capabilities between 2 ERP systems skipping IE, which made the communication fast and also gave the additional monitoring capabilities of PI to the communication.
With SAP PI 7.4, we do not have WS Adapter. Is this a set back? or Was it unnecessary looking at the existence of SOAManager configuraitons?
Can anyone some points on WS Adapter vs SOAMANAGER for WS-RM configurations/direct communication between 2 ERP systems?
Thanks and Regards,
Vikas Kumar Singh

(a) I am under the impression that WS -RM adapter used for Web services cannot be used in asynchronous scenarios. Am I correct?
Actually WS adapter only supports Asynchronous communication (EO/ EOIO)
(b) If WS-RM Adapter can be used for asynchronous scenarios, how do we do it?
The corresponding Service Interface (in your case sender) should be having mode as Asynchronous
(c) Since I assume that WSRM Adapter cannot be used for asynchronous scenarios, if I use the scenario WSRM - IDOC
(asynchronous) adapter, then I have to use BPM (Sync-Async communication). Am I correct to believe that WSRM -IDOC
integration is not possible without BPM?
(d) In case WSRM-IDOC integration is ONLY possible with BPM, is WS-RM --- ABAP Proxy better than WS-RM -- IDOC integration?
NA
Update:
To confirm what I said refer the QoS column for WS adapter in the table over here:
http://help.sap.com/saphelp_nwpi71/helpdata/EN/0d/5ab43b274a960de10000000a114084/content.htm
Regards,
Abhishek.
Edited by: abhishek salvi on Sep 24, 2009 8:27 PM

Similar Messages

I just bought a power adapter and it is not working, says "not charging". The same for the mobile charger. Anything I need to do in the setting?

I just bought a power adapter and it is not working, says "not charging". The same for the mobile charger. Anything I need to do in the setting?

The device is locked to the carrier it was purchased through unless you specifically purchased it as unlocked directly from Apple.
Only the carrier to whom it is locked can authorize it's unlocking. To do so, the user much contact them to start the unlock process.

PI 7.4 single stack web service adapter alternative

Hi All,
Looking at upgrading from 7.11 dual stack to 7.4 single stack and I know the web service adapter is no longer available (at least according to anything I have read, but I understand it is in the pipeline).
How do we provide and consume web services on a single stack environment?
I have looked hard, but if the answer has been before me I have failed to recognise it due to my own limitations.
If someone could point me in the direction of any articles/blogs/discussions that answer my question or can answer the question I would be very grateful.
thanks in advance
Julian

Hello Julian,
WS adapter has not been migrated from ABAP stack to Java stack so far - so, in Java-only installation options of PI, there is no analogue for it from functional replacement perspective.
For web services consumption, the SOAP adapter can be used, but it is applicable for plain SOAP communication, not for WS-RM.
Regards,
Vadim

Can I use an adapter with the output stats: 5.2 volt and 1.0 amp for my iPod Touch 4g?

Hello, I bought an iPod touch from apple store. I got the cable with one part to the iPod and the other USB. But i didn't get an adapter to make it possible to connect the USB to an adapter and then into the wall jack.
So I had one at home with these stats: 5.2 volt and 1.0 amp. Can I use it to charge the iPod Touch or is it "unhealthy" for the battery?
Kind Regards
Kiwiii

It shuld be fine. It is within the tolerance for USB 5 Volts.

Duplicate File Handling Issues - Sender File Adapter - SAP PO 7.31 - Single Stack

Hi All,
We have a requirement to avoid processing of duplicate files. Our system is PI 7.31 Enh. Pack 1 SP 23. I tried using the 'Duplicate File Handling' feature in Sender File Adapter but things are not working out as expected. I processed same file again and again and PO is creating successful messages everytime rather than generating alerts/warnings or deactivating the channel.
I went through the link Michal's PI tips: Duplicate handling in file adapter - 7.31 . I have maintained similar setting but unable to get the functionality achieved. Is there anything I am missing or any setting that is required apart from the Duplicate file handling check box and a threshold count??
Any help will be highly appreciated.
Thanks,
Abhishek

Hello Sarvjeet,
I'd to write a UDF in message mapping to identify duplicate files and throw an exception. In my case, I had to compare with the file load directory (source directory) with the archive directory to identify whether the new file is a duplicate or not. I'm not sure if this is the same case with you. See if below helps: (I used parameterized mapping to input the file locations in integration directory rather than hard-coding it in the mapping)
AbstractTrace trace;
    trace = container.getTrace();
    double archiveFileSize = 0;
    double newFileSizeDouble = Double.parseDouble(newFileSize);
    String archiveFile = "";
    String archiveFileTrimmed = "";
    int var2 = 0;
    File directory = new File(directoryName);
    File[] fList = directory.listFiles();
    Arrays.sort(fList, Collections.reverseOrder());
    // Traversing through all the files
    for (File file : fList){
        // If the directory element is a file
        if (file.isFile()){
                        trace.addInfo("Filename: " + file.getName()+ ":: Archive File Time: "+ Long.toString(file.lastModified()));
                        archiveFile = file.getName();
                      archiveFileTrimmed = archiveFile.substring(20);
                      archiveFileSize = file.length();
                        if (archiveFileTrimmed.equals(newFile) && archiveFileSize == newFileSizeDouble ) {
                                var2 = var2 + 1;
                                trace.addInfo("Duplicate File Found."+newFile);
                                if (var2 == 2) {
                                        break;
                        else {
                                continue;
    if (var2 == 2) {
        var2 = 0;
        throw new StreamTransformationException("Duplicate File Found. Processing for the current file is stopped. File: "+newFile+", File Size: "+newFileSize);
return Integer.toString(var2);
Regards,
Abhishek

Car Adapter Capabilities for Zen Nano Plus

hello, i am fairly new to this whole thing...i have the Zen Nano Plus and want to be able to play my music in my car....is this possible? and what do i need to buy to do so? i just dont feel like searching for the answer myself, figured this would be quicker!!!

thanks!!!!

berries674 wrote:
i just dont feel like searching for the answer myself, figured this would be quicker!!!
And you expect an answer!
PB

DVI to Video Adapter with NVIDIA 8800 GT not working

Hi all. I have the new Mac Pro Octo (mar '08) with the NVIDIA GFORCE 8800 GT card. I cannot find anywhere what may be wrong. Only on the Apple Website for the adapter that the only Mac Pro it works with is the Mac Pro (with ATI X1900 XT). However, both tech support and Apple's Store staff said this would work, prior to buying it. Well, my computer does not recognize the TV monitor hooked up via S-Video. I've powered everything down, restarted, unplugged and replugged in both orders, and switched inputs on the TV and receiver both. Nothing.
Any one know if this does or does not work with this computer???
Thanks.

Never mind. Found this out via Apples own website. Thanks APPLE TECH SUPPORT and STORE STAFF for getting me to buy a useless cable!
Mac Pro Computers (January 2008)
The Mac Pro computers with Quad-Core Intel Xeon 5400 Series microprocessors were introduced in January 2008. The Mac Pro’s graphics subsystem interfaces to the North Bridge via a 16-lane PCIe 2.0 bus. For information on the PCI Express graphics support and expansion, refer to PCI Developer Note.
The following sections describe the Mac Pro’s graphics subsystem.
Graphics Cards
Supported graphics cards have dual-link DVI connectors, supporting 30-inch Apple Cinema HD Displays on both ports.
For information on video memory, power, and features refer to Table 1.
All of the supported graphics cards support dual displays in either extended desktop or video mirroring mode; for more detail, see “External Display Modes.”
Table 1 Supported Graphics Cards
Graphics card
Video SDRAM
Power usage
ATI Radeon HD 2600 XT (standard)
256 MB (GDDR3)
50 W
NVIDIA GeForce 8800GT (configure to order)
512 MB (GDDR3)
110 W
NVIDIA Quadro FX 5600 (configure to order)
1536 MB (GDDR3)
175 W
The GeForce 8800GT graphics card requires that a booster cable be connected from the PCI slot to the auxiliary power connector. The Quadro FX 5600 graphics card requires two booster cables be connected from the PCI slot to the auxiliary power connector. For additional information, refer to the PCI Developer Note.
The Mac Pro supports the 20-inch Apple Cinema Display at a resolution of 1680 x 1050, the 23-inch Apple Cinema HD Display at a resolution of 1920 x 1200, and the 30-inch Apple Cinema HD Display at a resolution of 2560 x 1600. All ports support a maximum resolution of 2048 x 1536 at 32-bit with 85 Hz refresh rate. Multiple PCI Express graphics cards can support three or more displays.
The table below lists the displays supported by port 1 and port 2.
Table 2 Port 1 and Port 2 support
Graphics card
Port 1
Port 2
Radeon HD 2600 XT
20”, 23”, 30” Apple displays
20”, 23”, 30” Apple displays, DVI to Video Adapter
GeForce 8800GT
20”, 23”, 30” Apple displays
20”, 23”, 30” Apple displays
Quadro FX 5600
20”, 23”, 30” Apple displays
20”, 23”, 30” Apple displays
For information on video ports, see “Video Monitor Ports.” For information on PCI Express expansion slots, refer to PCI Developer Note.
Video Monitor Ports
The Mac Pro has a DVI connector for an external video monitor. For a description of the DVI connector, refer to Figure 4 and Table 30.
The graphics data sent to the digital monitor use transition minimized differential signaling (TMDS). TMDS uses an encoding algorithm to convert bytes of graphics data into characters that are transition-minimized to reduce electromagnetic interference (EMI) with copper cables and DC balanced for transmission over fiber optic cables. The TMDS algorithm also provides robust clock recovery for greater skew tolerance with longer cables or low-cost short cables.
Note: The Mac Pro computer includes a DVI to VGA Adapter.
DVI to Video Adapter
The Radeon HD 2600 XT graphics card supports an optional DVI to S-video/composite adapter that provides S-video and composite output to a PAL or NTSC video monitor or VCR. When a display is connected by way of the video adapter, the computer detects the type of adapter and enables the composite and S-video outputs. The settings for the resolutions and standards (NTSC or PAL) are then selectable in the Display pane in System Preferences.
Note: The DVI to Video Adapter does not come packaged with the Mac Pro computer and must be purchased separately.
The video output connector is a 7-pin S-video connector. Figure 5 shows the arrangement of the pins and Table 31 shows the pin assignments on the composite out and S-video connector.
The Mac Pro computer provides video output at picture sizes and frame rates compatible with the NTSC and PAL standards; the picture sizes are listed in Table 32. Those picture sizes produce under-scanned displays on standard monitors.

Filename for flat file using J2EE FILE FTP Receiver adapter

Hi there,
I am struggling to do the following:
I have a J2EE File receiver that sends a file with a specific name to a FTP destination. I define the target filename in my graphical mapping using certain criteria and a incremental number. In my adapter I use variable substitution to select that value in the payload as the filename. Up to this point everything works fine.
The problem is that I convert the payload to a flat structure using xslt before writing it out and because of that the adapter cannot find my value as defined in the variable I use for the name.
Now, obviously if I move the xslt module after the CallAdapter module, the file won't be converted to a flat structure.
Can anyone give me advice on how I can do the flat conversion and the specific filename from the payload?
Thanks in advance,
Johan

Hi,
Instead of using variable substitution, use adapter specific identifiers to set the file name in mapping.
Ref:/people/michal.krawczyk2/blog/2005/11/10/xi-the-same-filename-from-a-sender-to-a-receiver-file-adapter--sp14
Regards,
Jai Shankar

Get filename from file sender adapter

Hi Experts,
I have a question regarding the file/ftp adapter (sender).
I have a directory with xml and pdf files. for every xml file there is a pdf file with the same filename. for example:
file1.xml
file1.pdf
file2.xml
file2.pdf
file3.xml
file3.pdf
Now I want to read the xml file with the file sender adapter. afterwards I want to read the related pdf file. for example: If I read the file file1.xml afterwards I want to read the pdf file file1.pdf with the file sender adapter. For this it is nessessary to get the filename from the xml file so that I can read afterwards the pdf file. How can I realise it?
Thanks and best regards
Christopher

Hi srinivas,
thanks for your quick answer.
That the file adapter is not able to read pdf files is clear to me. In this case I only want to transport the pdf. that works fine. I tested it.
the problem is the following:
I have a xml file with the name "file1.xml". I read the xml file with the sender file/ftp adapter configured with filename "*.xml". Then I want to import the pdf file with the name "file1.pdf". Therefor I need the filename from the xml file.do you know what I mean? So XI has to know the filename of the xml to import the pdf with the same name ...
regards

Different Attachment extension(.xls,.txt) in sender mail adapter

Hi Experts
Is it possible to use different type of attachment extension (e.g .xls,.txt) in the sender mail adapter?
My requirement is , the attachment in the mail adapter will be used as the main payload.So I am using PayloadSwapBean adapter module.
Currently I am using the following module key for .xls attachment and it is working.Configuration for .xls attachment is as follows
swap.keyName-Content-Disposition
swap.keyname-Content-Description
swap.keyName-Content-Type
swap.keyValue-attachment;filename="MailAttachment-1.xls"
swap.keyValue-MailAttachment-1
swap.keyValue-application/vnd.ms-excel.
Now, the attachment may be .xls or .txt file.
Now If I want to use .txt atachment then do I need to define all these parameter again and in that case what will be my content type for .txt file.
Your inputs required
thanks
Ayan

PayloadSwapBean will only convert the attachment as the main payload.
Yeah for reading excel file I have a separate custom adapter module.This is not in the scope of my question..
All I am asking , can .txt as well as .xls attachment be used in the same sender mail adapter.
If that is possible what will be my content-type for .txt or can I remove content-type and use only content-disposition and content-description so that any type of attachment it can recognise.
The momment I am specifying content-type , I am making it particular that only say .xls attachment , it will identify.
I hope I make you clear.Inputs required
Thanks
Ayan

Mini DisplayPort to VGA adapter not working under Vista (Boot Camp).

Hi there,
I'm facing a very serious issue with MacBook Pro Unibody running MS Vista under Boot Camp: using the Mini DisplayPort to VGA adapter to hook a projector is 95% impossible because the only resolution available is 640x480 or sometimes 800x600. No solution came from the adaptor firmware update, still same behavior: connecting the external projector/monitor toggles 640x480 resolution with no more choices available. Just 5% of attempts on selected projectors gave me access to the complete resolutions list.
This is having a serious impact on my job where I do need both Mac&Windows running natively and with external display capabilities, please I'm looking for some feedback from users facing the same problem or someone who had an official answer on this issue from Apple. Do avoid posting about using modded display drivers please: I know they exist but the adaptor should be working with original ones.
I can understand Apple does not support MS Vista issues but this seems to be a hardware/driver one.
I'd like to point out I'm using a clean Vista installation with Apple drivers (from the Leopard DVD) and I've run Vista (same version, same gfx drivers etc) under Boot Camp on my previous MPB (with integrated DVI output+adapter) on hundreds of different projectors with never a single problem.
Any feedback is really appreciated.
L.

I'm having the same problem. When I try to connect to the switch in our conference room (connecting both a flat panel display and/or a projector, both with much higher native resolutions), all I get is 640x480. This is a huge problem to using bootcamp, and I really need to get this to work. I was able to get a higher resolution 1280x800 on a separate, portable display, so I'm wondering if people have the problem with standalone projectors or only with projectors connected to some sort of switch, in my case an Extron MPX423A. I have also tried this in both Windows Vista (32-bit) and Windows 7 RC1 (32-bit), with the bootcamp drivers and the latest NVidia drivers, and the behavior is the same all around.

Mac mini HDMI to DVI adapter cable

The new Mac mini comes with a HDMI to DVI adapter cable. Typically these (Apple) adapter cables are also available for sale separately however at the moment no other Apple device (if one ignores the Apple TV) would need this cable and as every 2010 Mac mini already includes the cable it is it seems not listed on the Apple store.
As I am interested in getting more of these adapter cables, does anyone know if there is an Apple part number for them, or even an Apple service part number?

Be careful what you read and with your answers. The OP is inquiring about an HDMI to DVI adapter, not a DVI to HDMI adapter. They are two very different devices! Although HDMI and DVI are electrically equivalent, some adapters work in only one direction, so you cannot always just turn it around and run it the other way.
John, there are HDMI to DVI adapters available from 3rd parties. Be careful that it has a return policy and a warranty. Some adapters are not to the standard and are not functioning as expected. I have been happy with Monoprice products, but have no experience with this particular adapter that you seek.
Currently the Apple Store has two Belkin adapters. If Apple sells it, it usually works well.
http://store.apple.com/us/search?find=HDMItoDVI&mco=MTA4NDUyNzc
Dah•veed

Problem w/mini-display to DV I adapter, a Macbook Pro 13" & 30" Cinema Disp

I recently switched out my old 15" MacBook Pro for a new 13" version. My old MBPro had a DVI input and the connection between that machine and my 30" Studio Display was not a problem.
However, as I now have the 13" and need to use the mini-display adapter I am getting occasional screen flicker and worse, total static on the screen. It's like I'm in the 1950 watching a B&W TV with rabbit ears.
I have checked and rechecked all of the connectors, but this has become a daily battle to get a clear picture.
I know the display has some years on it, but it's been good till now and I'd like to hold on to it.

Make sure you have the latest version of the Mini DisplayPort to Dual-Link DVI adapter. Check via System Profiler (Utilities folder). It should be at least 1.0.2
<http://mjtsai.com/blog/2009/10/03/mini-displayport-to-dual-link-dvi-adapter-imp roved/>
It could also be a problem with USB power for the adapter. If you have a charger for iPhones or iPods that use USB, try using it to power the adapter (plug the display's USB cable into the computer).

What s-video cable for a DVI to S-Video adapter

Hi,
I have an old MiniG4 lying around, which I thought I'd make into a media centre.
I bought the Apple DVI to Video Adapter (<http://store.apple.com/us/product/M9267G/A>) which is specifically for a Mac Mini and I thought that I had an s-video cable too, but clearly I have the wrong one.
The cable I have, has a single plug at one end and the red/white/yellow plugs at the other end. The single plug is a headphone-jack style, but with 3 yellow connector 'stripes' instead of the usual 2 black ones, but this plug doesn't fit in the DVI Adapter's yellow socket. It's too wide.
Can anyone tell me what cable I need to work with the DVI Adapter? Should it be 2 plugs to 3, or 1 plug to 3? (I'm in Europe, if that changes anything)
(Why don't Apple tell you what you need on the product page at the Apple store???)

Thanks for the replies.
I found the correct cables ... really dumb that Apple sell adapters but doesn't tell you what is required for them to work.
Anyway, it works really well. I was surprised at how good the output is. Just like the original DVD. The only place I can see any artefacts is on a totally black screen. Should it be of interest to anyone else reading, I used Handbrake on preset AppleTV but with FFMPEG instead of H624 (which took incredibly long to encode) and choosing to maintain aspect ratio and 100% quality.
I'm also using the iPhone to control via Apple's 'Remote' iPhone app and I bought 'Rowmote' as well, which gives more control.
The G4 Mini is the 'stealth' version, the last one they made with a slightly faster processor and a more capable video card. It's adequately powerful for running the movies and acting a media hub.
All in all, I'm quite happy.

Will the old 23" ACD work with the Mini DisplayPort to Dual-Link DVI Adapte

Will the old 23" ACD work with the Mini DisplayPort to Dual-Link DVI Adapter and the new MacBook Pro?
Apple Store says it is for the 30" only.
Thanks ... Ken

I'm not so sure about that. I'd say the jury's still out until someone gets one and tries to use it single-link.

WS Adapter(PI 7.1) vs SOAManager? PI 7.4 Single Stack capabilities for WS-RM

Similar Messages

Maybe you are looking for