WS2012 R2 Recovery from Windows Backup Not Working

Hi,
I tried to perform a bare metal recovery of a Windows Server 2012 R2 operating system backup but I can't get it to recover or access earlier restore points. Any help would be appreciated! I want to avoid reinstalling the OS *again*.
I have a hardware install of Windows Server 2012 R2 on drive (a), backup services saved to drive (b), and my server folders on RAID pool (c). I had verified that Windows Server Backup was executing daily and I was previously able to see several backups
in the list of restore points.
I first tried to use the Windows Recovery Wizard to restore a "Volumes" recovery on drive (a); however, I can't select the "Source Volume" (C:) to equal the "Desination Volume" (C:). I just want to replace the current drive
(a) with what's backed up. Why is this? Should this be working with source equal to destination?
Then, when restoring Windows using startup disk & recovery options, I can't see more than the last backup. Older restore points are not available. Plus, my local administrator password is not being accepted. So many things are going wrong...
The last thing I did was enable the Windows Server Essentials role and set it up, which did include picking a domain name. I wasn't happy with the ".local" TLD that was automatically created so I wanted to restore before Essentials was set up.
Is this what is preventing a recovery?
Thanks!
Steve

Hi Steve,
For performing a restore, please make sure you boot with an installation disk and restore to correct target volume - here is an article with pictures incase there is any difference on your side:
http://blogs.technet.com/b/sbs/archive/2010/06/11/how-to-perform-a-bare-metal-restore-on-small-business-server-2008.aspx
Note: Steps are for Windows SBS 2008 but it is the same as using a Windows 2012 R2 installation disk to do a recovery.
Meanwhile from the description, it is a file server before installing Windows Server Essentials role. So it is a domain controller now.
Then it should also work by uninstall Windows Server Essentials role:
It may not able to be uninstalled at once but it will suggest to uninstall some roles (which it installed in order to convert to Essential server and a DC) first. If all suggested roles could be uninstalled, you can also uninstall Windows Server Essentials
role so that it will back from DC to file server - you can reinstall it later.
If you have any feedback on our support, please send to [email protected]

Similar Messages

Windows backup not working

Hi,
I'm trying to run a windows backup but it's failing with the following error.
Server specification: " Microsoft web server 2008 R2 sp1"
Error showing in backup tool: "The operation was stopped Detailed error The system writer is not found in the backup"
Error in event logs: Two events one with even 8193(total four entries) and one event with ID 517
errors: Volume Shadow Copy Service error: Unexpected error calling routine XML document is too long. hr = 0x80070018, The program issued a command but the command length is incorrect.
Volume Shadow Copy Service error: Unexpected error calling routine CreateVssExamineWriterMetadata. hr = 0x80042302, A Volume Shadow Copy Service component encountered an unexpected error.
Check the Application event log for more information.
The backup operation that started at '‎2014‎-‎08‎-‎23T13:00:09.593737300Z' has failed with following error code '2155347997' (The operation ended before completion.). Please review the event details for a solution, and then rerun the backup operation once
the issue is resolved.
Running "vssadmin list writes" list some writes and all of them showing "no error".
Could somebody help me on this?
Regards,
Jaf

Hi,
The system writer fails because permissions to files in the %windir%\winsxs\filemaps\ or %windir%\winsxs\temp\PendingRenames directories are incorrect.
Please refer to the article below to resolve the issue:
Backup Fails with Error Message "Writer Missing" or "Failed" or "Timed Out" or "Waiting for Completion" in VSSADMIN
http://social.technet.microsoft.com/wiki/contents/articles/7309.backup-fails-with-error-message-writer-missing-or-failed-or-timed-out-or-waiting-for-completion-in-vssadmin.aspx
Best Regards,
Mandy
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Old queries from Windows XP not work in Vista

Some queries produced with the version Oracle BI Discoverer 10.1.2.1 and Windows XP Pro SP2 do not work with the version 10.1.2.3 and Windows Vista. New queries runs normally. Can you help me? Thanks.

I have solved the problem! I used Mediainfo and determined they were .dv files (not a format I was ever familiar with!) which of course just stands for digital video.
I renamed them with .dv and quicktime recognized them.
Thanks for offering help and hopefully this helps someone else.

Migration Assistant from Windows PC not working

I have just got my first iMac and now trying to use the Migration Assistant with the iMac but it is not working.
I have loaded migration assistant on the house pc and when runnung Migration Assistant on the iMac it recognises the Dell PC. However it then seems to lock and say 'looking for other sources' and then sits in a loop.
I then open Migration Assistant on the PC and that just says 'waiting for mac to respond'
Are there any additional settings I need to change on the PC? or anywhere decent for support - there's hardly any additional material on the Apple site.
My wife is wondering what was the point of getting a Mac if the first thing doesn't even work.
Very frustating

If you are going to Start Over... You may want to have a look here...
http://pondini.org/OSX/Setup.html
And here...
Migration Assistant tips and tricks

Windows Server 2012 - Backup failing with Exchange - The application will not be available for recovery from this backup. the consistency check failed

Hi
We have a Windows 2012 server with Exchange 2013, all is working fine except now i am getting issues with the backup.
'Exchange - The application will not be available for recovery from this backup. the consistency check failed for the component Microsoft Exchange Server'
I have checked the database all is fine, i have created a new db and move all mailbox;s over and then removed the old db, i have enabled circular logging and then disabled it, it seems no matter what i do i cannot get a full backup!
i did have to restore the server once and the backups still worked for about 4 days after that and then stopped, i have also tried to remove and re add the backup role!
i am stumped, any advice would be great!

Hi
Ok, i created a test db and tried to back it up right away, it failed, i did not add any mailbox's to it either. i got quite a few events in the windows logs, as well as the same event above i got the following:
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2038
Task Category: Exchange VSS Writer
Level: Warning
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Microsoft Exchange VSS Writer backup failed. No log files were truncated. Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9. Database 4843b37c-7b3c-42b2-8b57-1393615c2c15.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="32772">2038</EventID>
<Level>3</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261645</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>4843b37c-7b3c-42b2-8b57-1393615c2c15</Data>
</EventData>
</Event>
AND
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2038
Task Category: Exchange VSS Writer
Level: Warning
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Microsoft Exchange VSS Writer backup failed. No log files were truncated. Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9. Database db5826f3-1029-4219-ad80-441a0e94537a.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="32772">2038</EventID>
<Level>3</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261646</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>db5826f3-1029-4219-ad80-441a0e94537a</Data>
</EventData>
</Event>
and
Log Name: Application
Source: MSExchangeRepl
Date: 21/01/2013 10:16:30
Event ID: 2034
Task Category: Exchange VSS Writer
Level: Error
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
The Microsoft Exchange Replication service VSS Writer (Instance 75754d0d-8dfe-4909-8beb-5a4f824254a9) failed with error FFFFFFFC when processing the backup completion event.
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MSExchangeRepl" />
<EventID Qualifiers="49156">2034</EventID>
<Level>2</Level>
<Task>2</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261649</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>75754d0d-8dfe-4909-8beb-5a4f824254a9</Data>
<Data>FFFFFFFC</Data>
</EventData>
</Event>
and
Log Name: Application
Source: SPP
Date: 21/01/2013 10:16:30
Event ID: 16389
Task Category: None
Level: Error
Keywords: Classic
User: N/A
Computer: NERDS-DC01.nerds.local
Description:
Writer Microsoft Exchange Writer experienced retryable error during shadow copy creation. Retrying... More info: .
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="SPP" />
<EventID Qualifiers="0">16389</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2013-01-21T10:16:30.000000000Z" />
<EventRecordID>261650</EventRecordID>
<Channel>Application</Channel>
<Computer>NERDS-DC01.nerds.local</Computer>
<Security />
</System>
<EventData>
<Data>Microsoft Exchange Writer</Data>
<Data>
</Data>
<Data>The writer experienced a transient error. If the backup process is retried, the error may not reoccur. (0x800423F3)</Data>
<Data>
</Data>
<Binary>00000000A5120000981200000000000042BEB7C511CAC619E59C92030000000000000000</Binary>
</EventData>
</Event>

Popups: Navigation from view to window does not work

Hi,
I open a second window as popup. This window has 2 views embedded, displaying view1 first. On some actions I would like to navigate to view2.
Defining an outbound plug on view1 and an inbound plug on view2, connecting them and firing the outbound withith the onaction works absolutely fine.
However, for some reasons I would like to avoid a direct navigation, but would like to navigate from view1 to the popupo window and from there to view2 (or maybe another view, ofcourse also embedded in the same popup window). Unfortunately I fail on this scenario - I can fire the view-to-window plug, but the destination on the window side (handle in method) is never reached.
Since the same concept works fine on non-popup windows I wonder whether a navigation from view to embedded window does not work for popups?
Any idea?

Hi Yashpal,
no, just one window.
The first link is view1 -> window, the second window -> view2.
I.e., I fire in the view the outbound plug, which is connected with its window.
In the window I fire an outbound plug, which is connected to view2.
In theory this should work - for non-popup windows I do not have any problem at all, however, for popup windows the navigation from view1 to the window is not processed.
In the meantime I played a little bit further: Instead of firing a navigation from view1, I now fire an event defined in the component contoller, on which an event method is registered within the window. Doing so, I reach the window, which I didn't reach via the navigation link. Once in the window, firing to view2 works just fine ...
Hope the issue is a bit clearer now. Also I found a solution, I am surprised that the simpler way via navigation does not work.

ITunes drag to import new songs in library or to create playlists from folders on windows does not work!

iTunes drag to import new songs in library or to create playlists from folders on windows does not work!
WHY? I have to solve, how can I do? Thank you

up

"F11 System Recovery" during boot does not work after Cloning hard drive.

Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
Startup Menu (F11 System Menu works properly) only on original hard drive.
Following obtained from Disk Management & diskpart in Command Prompt.
GPT Disk <700GB>
Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
Partition 7 NTFS Primary 26MB/350MB [Recovery]
Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
Acronis True Image 2015
Acronis Backup for PC
AOMEI Backupper Professional
Macrium Reflect
Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
“Recovery
Your PC needs to be repaired
A required device isn’t connected or can’t be accessed.
Error code: 0xc0000225
You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
Thank you in advanced.

Hi,
How did you clone the HDD ? One-for-one or different method ?
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Backup not working for File Server

We have System Center 2012 Sp1 installed with Agent Version : 4.1.3453.0
We are protecting File Server which is member in DFS. We have Volume of More than 2TB and which is spanned accross multiple VHDs.
I am facing problem with Backup not working and DPMRA service is getting stopped unexpectedly. When i try to create recovery point manually i don't get option to syncrhonize the changes. 1st and 3rd option is geryed out.
I am getting Error on DPM as Affected area:   E:\
Description:   The replica of Volume E:\ on<ServerName> is inconsistent with the protected data source. All protection activities for data source will fail until the replica is synchronized with consistency check. You can recover data
from existing recovery points, but new recovery points cannot be created until the replica is consistent.
For SharePoint farm, recovery points will continue getting created with the databases that are consistent. To backup inconsistent databases, run a consistency check on the farm. (ID 3106)
   DPM failed to communicate with the protection agent on <Server> because the agent is not responding. (ID 43 Details: Internal error code: 0x8099090E)
   More information
Recommended action:   1) Check recent records from the DPMRA source in the Application Event Log on FUSE.win2k.internal to find out why the agent failed to respond.
2) Make sure that the DPM server is remotely accessible from <Server>
3) If a firewall is enabled on the DPM server, make sure that it is not blocking requests from <Server>
4) Restart the DPM Protection Agent service on <Server>. If the service fails to start, re-install the protection agent.
   Synchronize with consistency check.
   Run a synchronization job with consistency check...
Resolution:   To dismiss the alert, click below
   Inactivate
I have Re-installed Agent but it is not helping.
I have Other Volume labeled as F: and sized at 600 GB. Backup of that Volume is working fine for Same server.
Please Suggest how to troubleshoot.
Thanks in Advance.
Swapnil
Thanks, Swapnil Prajapati

HI Chris,
Sharing files using Bluetooth
To share files using Bluetooth, you first need to make sure Bluetooth is turned on, and then use Bluetooth File Exchange to send a file.
To turn on Bluetooth:
Choose Apple menu > System Preferences and click Bluetooth.
Select the On checkbox. To allow other Bluetooth enabled devices to “discover” your computer and send files, also select the Discoverable checkbox.
Select “Show Bluetooth status in the menu bar” so you can quickly send files and perform other actions using the Bluetooth status menu in the menu bar.
To send files using Bluetooth:
Choose Send File from the Bluetooth status menu in the menu bar.
If the Bluetooth menu isn’t visible, choose Apple menu > System Preferences, click Bluetooth, and select “Show Bluetooth status in the menu bar.”
In the window that appears, select the file you want to send and click Send.
Select the device you want to send the file to and click Send.
If you don’t see the device you want to send the file to, make sure the device has Bluetooth turned on and is discoverable.
You do not need File Sharing turned on for Bluetooth technology.
Another way to share files between two Macs is How to use Firewire Target Disk Mode
Carolyn

Rename files or folders in Windows 8 not working

Rename a file or folder on a Windows CE device is not working from Windows 8 when connected through Windows Mobile Device Center.
From Windows 7 it worked just fine!
This has been a problem for a very long time now, and im not alone according to all forums.
But no fix as far as i can find!
Is there anyone that have found a fix on this?

http://answers.microsoft.com/en-us/windows/forum/windows8_1-files/windows-8-unable-to-rename-files-on-pocket-pc/abae21b7-7ee1-41c7-853e-1ac7ea5b0413
It seems a issue in window 8.x system. Maybe you can ask for a MS support ticket.

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong v

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong version of backup.

Answer is no.
If you want the iCloud backup you have to have n internet connection, thus WiFi.
The not working WiFi has happened with quite a number of users.
It is not exactly clear what is the cause but there are suggestions to clear it up:
Some people have had success by removing an apostrophe from the iPhone name. If your iPhone is called something like “John’s iPhone” then this might work. Go to Settings > General > About > Name and change it to something with no apostrophe.
Some people have reported success by putting the iPhone into Airplane mode and then going to Settings > General > Reset > Reset Network Settings, but the problem may return.
You could also try going to Settings > Control Center and disable Access on Lock Screen then turn your iPhone off and on again.
Make sure that your router firmware is up to date.
Try backing up your iPhone and then restoring it. Check how to factory reset an iPhone for details.
If nothing is working for you, try contacting Apple or take your iPhone into an Apple Store.
Succes, Lex

Same issue Network Discovery not working and Windows Update not working

I've read the threads.
This is a Vista Ultimate upgrade. My OOOOH My I have clocked 8 hours
Everything was working before. I tried all of the recommended services turning on restarting.
Also, ran into the problem of my memory being eaten. Suspected cause hibernate mode, which I had to disable. Scott Hasselman blog recommended the fix which is a cheap work around that limits machines functionality!!
I'm and IT Engineer specializing in MS product lines since Windows 1.0. MFC foundation classes etc.. What is the real problem ?
I don't have the NetBIOS over tcp/ip in my services?
I figure that the cost of my time and other individuals pays for the OS four times over. Give me a Microsoft developer subscription or something to make me happy. This is my development machine and I'm loosing time and money.
FYI, Just upgraded my second machine to Windows 8.1 OMG !!2 Hours to upgrade after the download. I loose my configuration settings. I required to have a Windows Live whatever account!!! This is not the way to compete and keep customers.
Windows XP has been by far the best deployment experience. I need a Knowledge base that gives solutions , not a troubleshooting scenario that does or does not work!!
Please , don't tell me to go and by a OEM Surface I cannot recommend this to my clients.
Thank You

Hi,
If it worked previously, a quick solution is to run System Restore and get back to the previous status when the issue didn’t occur.
What is System Restore?
http://windows.microsoft.com/en-us/windows7/What-is-System-Restore
When you turn on network discovery, do you get any error prompt?
Please check if you have any error message about network discovery in event viewer.
Open Event Viewer
http://windows.microsoft.com/en-US/windows7/Open-Event-Viewer
What information appears in event logs (Event Viewer)?
http://windows.microsoft.com/en-US/windows7/What-information-appears-in-event-logs-Event-Viewer
Please use Windows Live SkyDrive (http://www.skydrive.live.com/) to upload the Error logs to a public folder and share the URLs with us.
Also, please temporarily turn off your firewall and all the security programs for a test.
As far as I know, Network discovery requires that the DNS Client, DNS Client, Network Connections, Network Location Awareness, Remote Procedure Call (RPC), Function Discovery
Resource Publication, TCP/IP Netbios helper, SSDP Discovery, and UPnP Device Host services are started and set to automatic.
You should check again if you have started all these services.
Regarding the update issue, I suggest you try the following suggestions.
1. Temporarily disable firewall and antivirus program to test the issue.
2. Open the Windows Update troubleshooter
http://windows.microsoft.com/en-US/windows7/Open-the-Windows-Update-troubleshooter
3. Reset Windows Update components
http://support.microsoft.com/kb/971058
You may follow the steps from the link below to fix the issue.
Windows Update Not Working.
http://support.microsoft.com/kb/555989
You may also see the common Windows Updates troubleshooting guide.
Fix Microsoft Windows Update Issues
http://support.microsoft.com/kb/906602
Hope it helps.
Regards,
Blair Deng
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Windows updates not working because it extract patches on Mac partition first., Windows updates not working because it extract patches on Mac partition first.

I have installed BootCamp 5.1 and Windows updates not working because it extract files on Mac partition before installation. Is there any workaround for same ?

To replicate this issue - Try to download .net framework 4.5 from microsoft website and than run that setup on windows partition.
Before installation. it will first extract all the binaries to a other drivers, since in my case other primary drive is E which is a Mac partition so it always give me an error while extractiing and therefore setup is not able to execute propely.
Let me try to get the screen shot of error and send it here.

Adobe Bridge CS5 in windows 7 not working?

Adobe Bridge CS5 in windows 7 not working. I was using bridge perfectly for last 2 years. It stops working since 3 days. I tried to install updates. Showing some error to install.
Tried to install creative cloud..again some error. Error code : 82
Could you please advice how I can fix my adobe bridge.

https://www.youtube.com/watch?v=xDYpTOoV81Q&feature=youtu.be
please check this video I uploaded..this is what happens when I click adobe bridge.. just blinks and go off. bridge not working on task manager

Consuming PI Webservice from Webdynpro Java Not working

Hello SAP,
Environment: CE 7.2.
Resolution expected immediately, Helpful answer is highly appreciated.
Is the namespace should not exceed 60char for PI Webservice, for executing the webservice from Webdynpro Java.
I tried with all the options in executing the PI Service from Webdynpro Java, None of the options worked. I am facing the below error while I was calling the PI Webservice.
I don't see any problem from Webdynpro Java, what ever the procedure I have followed is the standard procedure.
Fortunately when I execute the service from Webservice Navigator, it is working as expected. The same webservice when I consume it from Webdynpro Java it is not working
Options tried so far:
1) Published the Services to Service Registry and there by consuming the PI Service from Service Registry - Not worked
2) Tweaked the URL with few options - Not worked (Tweaking the URL, ex: portType, Binding)
3) Changing the Business Systems in PI and there after calling the service - Not worked
4) Initializing the code, instead of creating Service Controller and calling the PI Service - Not worked.
5) Created a Provider System and tried to call the PI Webservice from Provider System - Not Worked
For all the Options, I am facing the same error which is provided in the screenshot.
Below procedure which I have followed for calling the PI Webservice:
1) Created Adaptive Webservice Model
2) Provided PI Webservice URL (It prompts for PI System UserId and Password)
3) Selected Option - No Service Group Configuration
4) Provided Logical Destination
6) Completed creation of Model
7) Added the model as a UsedModel
8) Right Click on Comp Contr. and selected Apply Template and Created a ServiceController for the model (Entire mapping to comp contr, Initializing the nodes is taken care by Service Contr.)
9) Created an Template Action button and there by calling execute method which is auto rendered from CompContr..
10) Build the project.
11) Activated the code and Run the Application.
12) Getting the below error which is showed in the message.
ERROR MESSAGE:
Exception on execution of web service on destination 'GetPIHRPeopleData' for operation 'SI_CreateHRPeopleData_OS' in interface 'SI_CreatePeopleCompany_OS'

Hi Sankar,
If the webservice is working fine in the Wsnavigator then there is some problem with importing the webservice in webdynpro for Java. Please check the required parameter for creating the Adaptive Webservice Model. After adding in the used model and compoent controller binding, you need to write code for to execute the webservice model.
Please check the code for initialization and execution for the webservice and then test it.
Best Regards,
Arun Jaiswal

WS2012 R2 Recovery from Windows Backup Not Working

Similar Messages

Maybe you are looking for