WUSB. Another Wireless DAQ solution?

I wanted to begin doing data aquisition
wirelessly.
I think that using USB DAQcard and WiFi technology could be a good solution for a wireless DAQ application. But I was wondering if using USB DAQcard with a WUSB hub (like the belkin cablefree usb hub) could work fine.
Any suggestions or
info about WUSB technology and support for NI USB products would be appreciated. Thanks

Hi Widaq,
we haven't tested the WUSB hub with our USB board, but if these hubs have the same performance than the embedded ones, I think that all should work fine.
Regards
MarcoC
NI Spain/Italy

Similar Messages

DAQ Solutions not available on NI8176

DAQ Solutions not available on LAbview 6.1,DAQ Solutions button not highlighted cant be selected on opening Window. Hardware listed below.
- Installed on Embedded Controller NI8176/W2K.
- in PXI-1011 Chasis, NI 4472 in PXI slot, using a 6052E DAQ Card, SCXI Modules - 1540, 1520, 1102

Hello;
If you had another version of NI-DAQ installed before upgrading Labview to version 6.1, the best way to go about that is to uninstall NI-DAQ completely, and install the 6.9.2 version of the driver that goes with the Labview CD. To do that, just run the Labview installer and select the NI-DAQ driver from the list (choose custom install).
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

TS3276 Cannot send emails in mountain lion from another wireless network, when are apple gong to fix this

Cannot send emails in mountain lion from another wireless network, when are apple gong to fix this

You might be able to set up the SMTP server settings in Mail to authenticate with a password. That may get the email through.
In Mail Preferences, Accounts, select the account.
Click on the Outgoing Mail Server (SMTP) popup menu and select Edit SMTP Server List
Select the Server and then click the Advanced tab at the bottom.
Select Password authentication and add your details.
You might also want to set a custom port (even if it is one of the defaults)
This solution is normally for an email provider that will not let you send outside of your ISP network, which most prevent. They also must support password authentication of the SMTP server.

How Do I Connect An Airport Extreme With Password to another Wireless Devic

We have a setup for two different wireless devices so that there are multiple locations that can get online, but the entire setup has no passwords assigned. We would like to assign passwords to both wireless devices so that only the appropriate people are getting online. How does one do this?
The first wireless device that connects directly to the modem from the phone company is a brand new Apple Airport Extreme. The computer that set up the device so that people can get a signal was from a PC that is directly connected to the Airport Extreme via an ethernet cable. Also connected to the Airport Extreme is an ethernet cable that goes (50-100ft) to another wireless device - by Netgear - which then sends out another signal to pick up wireless internet, which is the signal/network that I work from.
If we assign a password to the Airport Extreme, I'm guessing it will complete screw up the connection to the Netgear. How would that be dealt with? And, how could we then, if we wanted, set up a password for the Netgear as well. I've read some initial information on the user guide CD and online, but I don't know the terminology of whether these are networks or just wireless devices 'bridged' together, etc.
My biggest concern, is it works right now, but the owner of the devices wants to put passwords on it and I want to make sure we can keep it working even with passwords. Does anyone know how to easily set up passwords and can I do it from my computer even though they were initially set up by a PC? Or do I have to do it from the PC and if so, how, because I am completely a Mac person and am very unfamiliar with Windows. Thanks.

Question that I need to know now is how do we set up a password on the Apple Airport Extreme now, when it is already set up and working without one?
Open AirPort Utility.
Select your base station, and then choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Click AirPort in the toolbar, and then click Wireless.
Choose a password scheme from the Wireless Security pop-up menu.
Enter the password all users will need in order to join this wireless network.
AirPort Utility 5.1 Help: Password-protecting your wireless network
Also, are there different types of passwords and if so, what is the most reliable one so that we don't lose connections, time out or have any other quirks?
There are different types of wireless encryption. WPA2 and WPA are the most secure especially when used with a non-dictionary password. 128 bit WEP is passable in most situations but not very strong. 40/64 bit WEP is extremely weak.
There is really no general "reliability" issue with any of them. Some devices aren't compatible with some of them.
If when we assign a password to the Apple Airport Extreme and for some reason the Netgear stops working, how do we unassign/take away the password on the Airport to get it back to the current setup that we know does work?
Follow the procedure above but disable wireless encryption instead of enabling it.

Daq Solutions Button Greyed out after reinstall

Problem: Purchased new NI PCI board (not sure the # now) and it came with NI-Daq 7.2 with it. I went to install it and found out it doesn't install with Windows95. Not that big of deal, needed to upgrade anyway. So, I installed a newer Pentium3 with Windows 2000 and installed all the drivers for the 2 PCI boards we use. Then I installed Labview 6i. After that I tried to install NI-Daq 7.2 and found out Labview installs an older version so I removed Labview completely, Installed NI-Daq 7.2, then reinstalled Labview 6i without the older NI-Daq verion that comes with it. Now when I load up Labview the "Daq Solutions" button is greyed out. I completely uninstalled NI-Daq and Labview again, reinstalled just labview with its olde
r (6.8) version of NI-Daq and still have the same problem. I searched here and didn't see any other solutions to this problem other than reinstall the software. I have done that 4 times now to no avail. Any other help?

Hendry,
First of all, what is the model of your PCI data acquisition board? Depending upon your board model, you may want to use NI-DAQ 7.0, since that will allow you to automatically install support for LabVIEW 6.i. NI-DAQ 7.2 should work with LabVIEW 6.i, but you may have to manually copy some files to appropriate locations. With your current installation, does your board show up in MAX? If so, can you run any of the data acquisition examples that ship with LabVIEW?

I need a backup system, but do not need another wireless system. Does Time Capsule offer just a backup option?

When I looked up Time Capsule on line, I found it provides backup and wireless connection. I don't want another wireless set up, just backup. Can I get just backup option with Time Capsule or do I have to seek an outside external backup device?

Does the OP mean he doesn't need a "wireless" system or does he mean that he doesn't need an additional connection to the Internet? The latter is my situation. I'm just wondering -- if I'm perfectly happy with my current routers --will it be easy to add a TC to my current setup? Would the TC get Ethernet-plugged into the router, or can it stand by itself (closer to where we have the printer)?

Wireless Bridge Solution

Hello,
I am looking for a wireless Bridge Solution the distance between 2 buildings is 200 Metre approx and the height of the buildings are 24 metres. The desired bandwidth is 11 Mbps and above.
Please help me in finalizing the solution. I am looking for a cheap solution other than 1300, 1400 or 1500 solution.
Regards..

You can always use a 1242 in bridge mode with external antennas. You will need a NEMA heated/cooled enclosure for the ap unless that will be mounted indoors, lightning arrestor and LMR cable to extend the antenna if required and antenna mounting hardware. But with most systems, you will need line of site, so hopefully you have this. Antenna wise, you can go with a yagi at both ends.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps6521/prod_qas0900aecd8031c8dc.html
http://www.cisco.com/en/US/prod/collateral/wireless/ps7183/ps469/product_data_sheet09186a008008883b.html

CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with AP 1242

Dear all, my customer has CWWLSE-1030-K9 Cisco WLSE Wireless LAN Solution EE 2.13 with 12 AP1242 (a/b/g) Radio 802.11g in place. Now he will buy additional AP what type of AP can i use because AP 12xx is EOS.

Hello Dirk,
AP 1200 is EOS, and customers were encouraged to migrate to 1240 Series (which is also EOS now)
http://www.cisco.com/c/en/us/products/collateral/wireless/aironet-1200-series/eol_c51-506611.html
Therefore it is recommended to migrate to Cisco Aironet 1600 or Cisco Aironet 2600 Series.
http://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-ip-phone-7900-series/end_of_life_notice_c51-726425.html

Why do i get a daq hardware configuration required window when trying to run the daq solution wizard?

i have recently installed the ni 4552 for pci dynamic signal analyser, and am attempting to configure my system and teach myself labview. when attempting to run the daq solution wizard i am presented with the daq hardware configuration required window.
Attachments:
DAQ_Hardware_Configuration_Required.ppt ‏38 KB

hi brian, thanks for your help. i have recently received version 6.1, and done a complete re-install. i have also downloaded the latest ni daq (6.9.2) and ni dsa (6.11) versions and installed them, but still i get the same error message when trying to open the solutions wizard (please see attached powerpoint presentation).
upon selecting the "go to ni daq config utility" option MAX opens. everything appears to be in order (device passes test, test panels run ok and virtual channels are configured correctly). i am unable to go any further.
i would appreciate any guidance that you are able to give me in this matter. many thanks in advance of your help.
best regards,
ben halkon

DAQ Solution Wizard greyed out in Labview 5.1

My DAQ board seems to be work correctly when using MAX, but in LabView the DAQ Solutions Wizard is greyed out. I have a PCI-MIO-16E-4 DAQ board, Labview v5.1 and NI-DAQ v6.9.2f8. I am running Windows 2000.

Make sure that the LabVIEW 5.1 support files have been installed along with NI-DAQ. Go to the Control Panel >> Add/Remove Programs >> NI-DAQ >> click Change >> select Add/Remove. If there is a red X next to LabVIEW 5.1 support, then it has not been installed. Install the entire feature and the DAQ Solutions Wizard should work.

I have setup wireless at home but when I travel how do I find another wireless network?

I have setup wireless at home, but when I travel, how do I find another wireless network?

Depends on where you are. Most all hotels/motels have wireless. There are Internet cafes, libraries, Starbucks, and many other places providing WiFi service.
In your iPad's Network settings you will usually find displayed all detected wireless systems. Not all of them may be usable unless they provide free access or you have a paid access membership. You should find this discussed in the user manual:
Please Get the iPad User Manual for iOS 5

HT3728 I do not need another wireless network but want to use the airport express for printer access only. Can this be done and how?

I do not need another wireless network but want to use the airport express for printer access only. Can this be done and how?

You can configure the AirPort Expess to "Join a wireless network" and enable the Ethernet port so that Ethernet devices will be able to connect.
In order to print from the iOS devices, you will need to have an application like Printopia installed on your Mac. The Mac must be active when you want to print.
More details here: Printopia - AirPrint to Any Printer - Print from iPad - Print from iPhone ...
There is a free trial available for Printopia, so make sure that it will work before you buy the AirPort Express.

Cisco Guest Wireless Access Solution - Local Printing

Hi,
Does Cisco have a solution that provides printing for a guest WLAN. Cisco Guest wireless deployment solutions recommend terminating the guest WLAN on an anchor controller in the DMZ which causes issues when needed to print locally as the print traffic will need to traverse the DMZ anchor controller causing excessive WAN link usage.
Is there a better solution to enable a guest WLAN to print locally?

FlexConnect with Split tunneling may work.
Read about this feature & see how that can be used in your branch setup. Here is the Ciscolive presentation slides the above came from.
BRKEWN-2016: Architecting Network for Branch Offices with Cisco Unified Wireless
HTH
Rasika
**** Pls rate all useful responses ****

WRT300N connect to another Wireless

Need help with a WRT300N V1.0
Trying to contact to another WIRELESS router. connect wireless, with no RJ45.
I want to place the WRT300N in another location NOT wired NO rj45 connect and connect to another wireless internet
internet ->> modem ->> wireless router#1 ->> / (not wired) WRT300n #2 V1.0 (wireless) ->> (wired) LAPTOP/VOIP
SETUP
-->> devices wirelss ; iphone(my perso white), iphone (my biz black),
-->> devices wired; ibm thinkpad #1, VOIP #1 (google voice), VOIP #2.
Does this router has this ability to connect to another wireless ?
If yes, how would I configr ?
would other Firmware do this DD-WRT ?
Message Edited by MrSmith on 01-30-2010 11:12 AM
Message Edited by MrSmith on 01-30-2010 11:16 AM

Linksys wireless routers WRT do not connect wireless to other access points. WRTs are access points, not bridges nor repeaters.
dd-wrt add bridging capabilities. Remember, dd-wrt will void your warranty.

My wireless Apple keyboard won't connect, it just keeps blinking to pair, but nothing connects. I even tried hooking up another wireless I have and it does the same thing. Should I delete it and set it up again?

My wireless Apple keyboard won't connect, it just keeps blinking to pair, but nothing connects. I even tried hooking up another wireless I have and it does the same thing. Should I delete it and set it up again?

Hey Apple Health,
Welcome to Apple Support Communities! There's an article that helps to resolve issues with wireless keyboards. I'd take a look at it, go through the troubleshooting steps, and see if that resolves the issue for you:
Troubleshooting wireless mouse and keyboard issues
http://support.apple.com/kb/TS3048
Best,
David

WUSB. Another Wireless DAQ solution?

Similar Messages

Maybe you are looking for