WVC80N - Internet Gateway UPnP discovery failure message \ unable to view over the internet

I have the WVC80N.  I recently got the new Comcast modem \ wifi but the Wifi is junk and had a lot of problems (loss connection, range etc) so I had Comcast "bridge" it so I just use my old wifi (LinkSys E1200).   I have TZO to handle remote viewing.  Everything was working great for about two weeks and we had a power outage.  Since then, I have been getting UPnP discovery message (in the status tab of the WVC80N camera site) and I am unable to view over the internet.  I get a 502 error usually but today I got extra info: "The socket connection to www.dfgehring.mylinksyscam.com failed.
ErrorCode: 10060.  A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond."
I had Comcast do a "repair / reset" transmission to the modem and still get the problem.
I found these step on the forum:
  1. Home Wirless Rounter administration page, find the UnPn settings and Turn off UnPn and save it. Wait for atleast 30 sec  and go the same page and Turn it back on.
  2. On your wireless camera Adminstraion page, go to "Options" and find the UnPn if it is already disabled go ahead and "enable" it also "enable" the "Alternate web connection" and save it. If it was already enable please disable it save the settings and enable back on.
 The above 2 steps resolved my issue and I could able to view my camera from outside of my home network.
Still no luck.  Tried it several times.
Could the power outage reset something on the modem or router to change this? 
Thanks
Darren

That's what I thought. The power outage may have set the modem, router or camera settings back to factory defaults causing it to loose connection. First thing first, call comcast and check if the modem is still on bridge mode. The modem may have been set back to a modem/router mode due to power outage.
You may test if the remote access is properly set up in the network by going to http://ping.eu. In that site, you will see your internet ip address, take note of that. Click on port check, enter your internet ip address and the port number you used in the alternate web access port then click Go. If it says closed, there something wrong in the settings of either the router or camera. In that case, I suggest you reset the router and camera and then reconfigure them.
I found these articles online which could help you reconfigure your router and camera settings:
How to set up your router
How to set up router wireless setting
Connecting camera to wireless network
How to set up remote access on linksys camera
How to set up TZO on the linksys camera
Hope these helps.

Similar Messages

  • Exception Message=Unable to connect to the VMM database because the database is in an inconsistent state.

    Hello,
    I have a problem with SCVMM 2012 R2, it always gives error when tries to "Run the dynamic optimizer" process. The process starts automatically every 30mins. When I analyzed report.txt file I found error message:Exception Message=Unable
    to connect to the VMM database because the database is in an inconsistent state.Contact an experienced SQL administrator whenever this error occurs. In some cases, it may be necessary to restore the VMM database. If the problem persists, contact
    Microsoft Help and Support.
    NOTE: If I start the process manually, it completes without any errors.
    Any help would be appreciated

    I'm led to believe this is a bug in UR5 and I think it was a bug in VMM 2012 SP1 RTM.
    Our TAM says this will be fixed in UR6. We had to turn off Dynamic optimizer or we could have rolled back to UR4 but there were other bugs in UR4 which hurt us more.

  • Since updating my iPhone 3GS to iOS 4.3.3 I have been unable to sync my photos! Keep getting the error message unable to sync and 'the required file cannot be found.' Please help?

    Since updating my iPhone 3GS to iOS 4.3.3 I have been unable to sync my photos! Keep getting the error message unable to sync and 'the required file cannot be found.' Please help?

    Try deleting the iPod Photo Cache on your computer.
    http://support.apple.com/kb/ts1314

  • BB Curve 8310 - Message -"Unable to look up the user info in database"

    Have contacts with email address uploaded from older model. Receive emails ok...have also set up two addresses for myself, however when trying to either manually place the email address or select one from my contacts, I get the response
    "Unable to look up the user info in database" when trying to send email
    I have created a CSV file for my contacts to transfer to the Curve however I don't know where to go from there. 

    Unable to look up the user info in database - KB03414
    SOLUTION HERE.
    If your issue is resolved, put a checkmark in the green box that contains the resolution.
    OR
    If it was just/or also really helpful - Give it a Kudos.. Go on Mate.. Help the rest of the clueless blackberry user world find their answer too..
    ~Gday from Down Under~

  • HT201320 How do I change the number of email messages I can view in the new iOS.

    I have the new IOS on my phone and can't find the setting that allows me to change the number of email messages I can view. Anyone know?

    You should have 200 undos, and can verify this in the bottom left flyout >> show >> number of undos (this show shows many undos you have cahced, not your max amount, will max out at 200)
    You can try changing the 200 in the illustrator preferences, by using a text editor, saving and then booting illustrator. Not sure this is a great idea, as 200 should be plenty, but let us know your results if you try.
    /undoDepth 5
    /maxUndoDepth 200
    Older versions of Illustrator let you change this in the preferences, but they must have decied that hitting CMD Z more than 200 times is not a good way to spend your afternoon.

  • Sending text messages to pc's over the network

    OK, so I know the system administrators where I work can send me text messages over their network directly to my computer.  How do you do this over the Linksys wireless network?  (Directly - as in not using an IM program).  Thanks!

    There is this nifty little program you can use over a LAN... http://www.dynatalk.com/

  • Messages window jumping all over the place in Yosemite?

    Since upgrading to Yosemite, my Messages window (specifically, the window with the message threads in them, Cmd-0) is jumping all over my screen when clicking on the window to bring it forward or clicking off the messages window into another window or to the finder. It's not 100% reproducible, but happens maybe 25-50% of the time.
    I'll be working in Safari, click on the messages window to view a chat, then click in the box to type a response and the window moves to the location of the mouse, as if I had dragged it there. Or I'll type a reply to a message, and then click onto Mail or Safari, and the window magically jumps to where I clicked, again as if I had dragged the window.
    I have not experienced this behavior with any other apps or windows. Only the Messages window in the Messages app, and only since upgrading to Yosemite.
    Has anyone else experienced this? Any ideas?

    Added to the Lounge area with a link to this Thread.
    It seems that many are reporting that if the Main (chat and Interface) window is partially behind another app then clicking on it does bring it to the "front" but the next click to do anything moves the window to that spot on the Screen.
    This seems to be something to do with the focus of the window.
    The people I have asked and responded have said it effects new and older machine alike, including with and without Retina Displays.
    Also Laptops and Desktop seem to be equally affected.
    They also report that they have not found other apps that it happens to.
    Asking people to delete com.apple.ichat.plist achieves nothing even though this .plist holds the windowing info.
    At this point I am at a lost as to what to suggest and feel it might be beyond the scope of User to User Suggestions.
    At the same time I also think the numbers are low.
    9:50 pm      Thursday; October 30, 2014
    ​  iMac 2.5Ghz i5 2011 (Mavericks 10.9)
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb (Snow Leopard 10.6.8)
     Mac OS X (10.6.8),
     Couple of iPhones and an iPad

  • TS5376 I get this message : unable to connect to the Itunes store (-3212) . I do have internet, did the unistall and reinstall steps in support. help!

    I get an error message with code (-3212) . I do have internet access, using windows 7.

    Hey qkslvr01,
    Thanks for the question. I understand you are experiencing issues with connecting to the iTunes Store. The following articles may help to resolve your issue:
    Can't connect to the iTunes Store
    http://support.apple.com/kb/TS1368
    iTunes: Advanced iTunes Store troubleshooting
    http://support.apple.com/kb/TS3297
    "Error 3000" through "3999"
    Alerts with codes in the 3000 range generally mean that iTunes cannot contact the gs.apple.com server on ports 80 or 443. This may be because out-of-date or incorrectly configured security or firewall software is interfering, or due to your Internet proxy settings. If you are using a proxy, try removing the proxy settings, or using a known-good network. If that does not resolve the issue, follow iTunes for Windows: Troubleshooting security software issues.
    Thanks,
    Matt M.

  • Had to reload i tunes following hard drive reboot now cannot acess i tunes stor keep getting error message "unable to connect to the internet connection timed out " but I have no problem getting onto the internet

    Had to redownload i tunes following hard drive reboot but now cannot connect the i tunes store as I get the following error message " itunes could not connect to the itunes store the connection timed out " I get this message as soon as I click on the store.
    Any ideas how to solve this  ?????
    Bill

    Had to redownload i tunes following hard drive reboot but now cannot connect the i tunes store as I get the following error message " itunes could not connect to the itunes store the connection timed out " I get this message as soon as I click on the store.
    Any ideas how to solve this  ?????
    Bill

  • I'm getting a PDP authentication failure message and cannot connect over 3G. Help?!

    A few days ago I suddenly started getting an error message when trying to connect to the internet over 3G.  "Could not activate cellular data network. PDP authentication failure" 
    I am in Germany, on Telekom.  Have called Telekom customer service and went to the Telekom retail store.  Neither could figure out the problem and advised I do a factory restore on the iphone via iTunes.  I did that and am still getting the error message. 
    The only weird thing that happened before the error started showing up is I had called Telekom the night before to add a U.S. data roaming package to my phone plan for an upcoming stateside trip.  They told me to text "W2S" to 7277 in order to add the U.S. data roaming plan.  I did that, and the next morning this error started popping up.  Don't know if that is related or coincidence. 
    I am traveling to the states in a few days and would really like to get this cleared up.  The only option Telekom has left for me is to mail my phone in to Apple.  :-( 

    If I may ask, what country are you from?
    To note, what you see is just not possible from a radio communication level, you're the first I've ever seen with this problem. (see photo and footnote below)
    Since you said the Carrier option is available, can you go to it, turn off automatic and see what networks show? Normally it you will see At&t and T-mobile, however, if you see Sprint,  you will need to go talk to Apple.
    But if T-mobile does show, select it and see if your phone connects.
    If not, remove the SIM card reboot the phone and try again.
    I'm sorry about not being clear about the phone number,  while connected to the Verizon network, is the phone number showing your T-mobile one or is it something different?
    For reference,
    Normally, what you will see in the status bar when on the Verizon network when not on 3G/LTE is the 1X symbol.
    GPRS is a completely different communication type from 1X and Verizon doesn't support it. If you visit a Verizon store (or T-mobile) the staff will probably be surprised and confused about what your phone is showing.

  • Since upgrading to iOs 5.1.1 and iTunes 10.6.1.7 my phone gets a sync failure message whenever I since thru the cable. I have no problem syncing with my iPad

    Since I upgraded to iOs 5.1.1 and iTunes 10.6.1.7 my phone will no longer sync with outlook or iCloud. I have no trouble with my iPad. I get a message "iPhone could not be synced because the sync session failed to start. Any suggestions?
    BW

    Is your iPad recognized by iTunes when connected to your computer via USB?
    If so, does Sync with this iPad over Wi-Fi remain selected under the Summary tab for your iPad sync preferences with iTunes?

  • What do I do when I try to verify a second iCloud email account for iMessage on my iPad and I get an error message, Unable to verify because the email is already in use. Thanks for any answers.

    My iMessages that I write on my iPad are not showing up on my other device, the iPhone 4.  I went into the settings and tried to add the second cloud email address, however, I keep getting an error message saying that it cannot be verified because the email is already in use. What do I need to do get it working. I have two iCloud email addresses.  Thanks in advance for your suggestions.

    Hi,
    Just wanted to say I found out the answer. I should have looked first to see if anyone else was having the same problem but I didn't. 

  • Unable to view all the pdf menu bar in internet browser

    We are working on a web application where we have to provide options to users to edit pdf directly(like changing the text) and save to the server again. I installed acrobat professional on my machine to develop the code. But when i open the pdf in my web application(i.e Microsoft Internet Browser..) it is just showing few tool bars, but i need to load all the menu bars so that user can use all the menus which is available for adobe professional. Thanks for your help.

    When viewing a PDF in a web browser, one is using a special plugin for the web browser to read PDF files. I have the same problem when I have an Excel file opened in a web browser, there is no Excel menu bar or toolbars.  You might be able to add some JavaScirpt to the PDF to display the necessary tool bars.
    I always wondered why they call these internet viewers browsers.

  • I can't access hotmail or gmail. I get the message "unable to connect to the server". However I can access both msn and google main page and not problems with other sites. Any ideas of what to do?

    Cannot access hotmail or gmail, although no problems with the actual msn home page or other sites. I get the message: Firefox can't establish a connection to the server at .....
    == URL of affected sites ==
    http://login.live.com; http://www.google.com

    Hi thanks for reply.
    No, not that I'm aware. How/Where can I check this?
    The only think I've done recently is install a different antivirus program and uninstall the old one which had expired. Not sure if this is linked to the problem...?

  • Unable to view all the pdf menubars in internet browser

    We are working on a web application where we have to provide options to users to edit pdf directly(like changing the text) and save to the server again. I installed acrobat professional on my machine to develop the code. But when i open the pdf in my web application(i.e Microsoft Internet Browser..) it is just showing few tool bars, but i need to load all the menu bars so that user can use all the menus which is available for adobe professional. Thanks for your help.

    When viewing a PDF in a web browser, one is using a special plugin for the web browser to read PDF files. I have the same problem when I have an Excel file opened in a web browser, there is no Excel menu bar or toolbars.  You might be able to add some JavaScirpt to the PDF to display the necessary tool bars.
    I always wondered why they call these internet viewers browsers.

Maybe you are looking for

  • In iOS 7 is there a way to turn off that new camera burst mode?

    I like the old camera ability to keep your finger on the shutter and release to take a photo. It helps avoid camera blur with certain close shots you are trying to frame, and was one of my favorite "hints on using your camera" for the iPhone. But wit

  • Alternative to Evergreen Check Printing

    Hi, We need to change the bank logo on our DIMM card (which is evergreen). When I contacted Evergreen, they tried to sell me DocuGuard Solution for around 5K. Is there any other alternative solution that anyone knows of? Thanks A/A

  • Pdf viewing on E-mail -weird!!-

    I can't open pdf files from email application on iphone 6 plus using latest ios 8.1.2 please help!

  • Problem to open collaboration launch pad

    Hi, I'm trying activate an instant messaging service in my portal. I've activated the collaboration launch pad, but when I click on the link I get the following error: "An exception occurred during the program execution. Below you will find technical

  • Using E-signature in PO Report

    Dears, We are planning to setup the e-signature for PO report, what's the steps and instructions that we want to do. Actually, we don't have enough e-signature knowledge base. As we know, firstly we have to change the report to XML. Your help will be