X BOX 360 unable to connect wired or wireless.. help?????????????

Hi all;
just bought a new X BOX 360, ive tried every single solution wireless or wired...i have an actiontec MI424wr current firmware,
keep getting that MTU incorrect error even tho i did reset it...i tried from 1364 to 1492....ive added the xbox in the router to open the xbox ports..(was a preset) have Universal plug n play on...looks like i am totally out of options..and looking at the googled question...with all the FIOS user that cant use XBOX im not alone..
also where the HECK is the direct i want to talk to someone in bangladesh FIOS support number??
Thanks

well, when you connect it wireless - do you know if you get an IP address? you would either see that in the xbox network status screen, or in your router.
so log into your router by entering http://192.168.1.1 into a web browser. admin is your username, and your password is on the service tag of your router. its located under the bar code and it starts with a CSJx0000000 it IS case sensitive.
when you log in click on my network at the top and see if the xbox is listed there.
If it's listed in there, (which I am assuming since you can use the preconfigured port forward) then you may just need to increase the MTU to 1500 in the router, or experiment with the MTU in the advanced settings.
Where are you putting that MTU ? in the xbox or in the router? the router is set to 1500 so maybe you should match it up. There's a lot of people that can connect their xbox live to the routers, so you shouldn't have too much difficulty, but we can try to help you.
I would start from scratch personally. so that means
Hard reset the router (in the back there is a reset button, press it and hold it for 15 seconds and let it go)
plug in the xbox to one of the LAN ports (1, 2, 3, or 4) do NOT plug it into the ethernet WAN port.
try to connect to the xbox again.
let us know what happens after that.
pill2u wrote:
Hi all;
just bought a new X BOX 360, ive tried every single solution wireless or wired...i have an actiontec MI424wr current firmware,
keep getting that MTU incorrect error even tho i did reset it...i tried from 1364 to 1492....ive added the xbox in the router to open the xbox ports..(was a preset) have Universal plug n play on...looks like i am totally out of options..and looking at the googled question...with all the FIOS user that cant use XBOX im not alone..
also where the HECK is the direct i want to talk to someone in bangladesh FIOS support number??
Thanks

Similar Messages

Macbook air is unable to connect on hidden wireless network

Dear users and support,
I have just bought my macbook air with lion os already installed, but I am unable to connect to hidden wireless network. Is there any trick to fix it? even though I am typing the name and password it's unable to login.
Please advice.
tks,

Back up all data before making any changes.
Step 1
Take all the applicable steps in this support article.
Step 2
If you're running OS X 10.8.4 or later, run Wireless Diagnostics and take the remedial steps suggested in the summary that appears, if any. The program also generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
Step 3
This step will erase all your settings in the Network preference pane. Make a note of them before you begin, and recreate them afterwards. It may be helpful to take screenshots of the preference pane.
Triple-click the line below on this page to select it:
/Library/Preferences/SystemConfiguration
Right-click or control-click the highlighted line and select
Services ▹ Reveal
from the contextual menu.* A folder should open with an item named "SystemConfiguration" selected. Move the selected item to the Trash. You may be prompted for your administrator password.
*If you don't see the contextual menu item, copy the selected text to the Clipboard (command-C). In the Finder, select
Go ▹ Go to Folder...
from the menu bar, paste into the box that opens (command-V). You won't see what you pasted because a line break is included. Press return.
Reset the System Management Controller.

I'm unable to connect to my wireless network

I am unable to connect to my wireless network on my iphone 4. It worked previously. My husband has no problem with his iphone connecting.

Same here. Upgraded 2 separate iPhone 4 to iOS 5 and now both get an error that say "incorrect password" when trying to connect. iPad 1 upgraded to iOS5 and all 3 macs connect fine using same password. (Router is Apple Airport base station running 7.5.2)

How to find remote computer/laptop connected Wired or Wireless?

hi
How to find remote computer (more than 1000) workstation connected wired or wireless? can some one give me the script to find
Regards
GG

Thanks for your reply. It gave the output like below. It not mentioned it's connected wired or wireless.. can you give me exact one
netconnectionid
Bluetooth Network Connection
Local Area Connection
Wireless Network Connection
Wireless Network Connection 2
Local Area Connection 3

I had a problem in my iphone's wifi.it doesnt connects to wifi. it says unable to connect . plz plz plz help me plz

i had a problem in my iphone's wifi.it doesnt connects to wifi. it says unable to connect . plz plz plz help me plz

Try the following:
1. Reset
Hold the Sleep and Home button down until you see the Apple logo
2. Restore:
http://support.apple.com/kb/HT1414
3. Recovery:
http://support.apple.com/kb/HT1808

Unable to connect to any wireless internet

laptop not supported any dongal to connect internet where as device connected other laptop. If i connect with Hot s[pot then its connected so request you to help on this & suggest what should i do. shoud i format ?

Hello @James0007,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your notebook computer is unable to connect to any wireless network. I would be happy to help you, but first I would encourage you to post your product number for your computer. Below is a is an HP Support document that will demonstrate how to find your computer's product number. In addition, it will also help if you indicate which operating system you are using; and whether your operating system is 32 or 64 bit. The more information you can provide, the better!
How Do I Find My Model Number or Product Number?
Which Windows operating system am I running?
Is the Windows Version on My Computer 32-bit or 64-bit?
Please re-post with the necessary information, this way I will be able to research this further for you. I look forward to your reply!
Cheers!
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Unable to connect with the wireless feature

I have the Linksys WRT54G version 8.0, it bridges with my DSL modem. I have 3 wired desktops and 1 wireless laptop (which does not connect without wired connection). According to the easylink advisor, we do not have an internet connection. But I have internet connection as long as all 4 computers are wired in. My problem now is we have a new ps3 and can not do the wireless connection. I have checked all settings on router page and still shows no connection. What am I doing wrong? How do I fix this? I can get on-line just can't use wireless. Can anyone help?
Thanks,
Sharon

You need to do Port Forwarding on your Linksys Router...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 80 and End box type in 80, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in DEF, in the start box type in 443 and End box type in 443, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the first line in Application box type in GHI, in the start box type in 5223 and End box type in 5223, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
4) On the first line in Application box type in JKL, in the start box type in 3478 and End box type in 3479, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
5) On the first line in Application box type in MNO, in the start box type in 3658 and End box type in 3658, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
6) On the first line in Application box type in PQR, in the start box type in 10070 and End box type in 10080, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings
7) Now assign the given ip address on your PlayStation
ip address :- 192.168.1.20, subnet mask :- 255.255.255.0, default gateway :- 192.168.1.1...
8) Also assign the dns addresses on the PlayStation
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
9) Turn off your modem, router, and PlayStation...Wait for a minute...
10) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the PlayStation and test it...
As your PlayStation is Wireless make sure you are connected to your Wireless Network...

Unable to connect netgear DG834G wireless to macbook

Hi
I am unable to connect the Netgear Router DG834G wireless to my Macbook. It works fine through the ethernet cable but when i try and connect wireless it says invalid password?

Hi
Changing your ISP won't fix this problem. There is one last thing that's worth a try....
Creating a new "Location":
System Preferences > Network
Select the AirPort from the left hand side
Click on the Locations combo box and select Edit Locations...
Click on + to add a new location, call it "Home" (or anything else you prefer)
Click on Advanced
Select the AirPort tab and enter your network name
Select TCP/IP tab.
Configure IPv4 Using DHCP
Now click on Renew DHCP Lease. After a few seconds you should get an IP address (probably 192.168.x.x)
Click on Proxies tab.
Select Auto Proxy Discovery and Use Passive FTP
Click on OK and Apply, etc.
If this doesn't fix your problem then I suggest your Airport card is failing and you need to visit an Apple Store.
Bob

Unable to connect to home wireless network with my iPod touch

I've had my iTouch for several months now and I'm still not able to connect to my wireless network at home. I've tried the resets and other suggestions I've found in the discussion groups but nothing has worked.
I have an older Netgear Router MR814v2 and it is unsecured. It is attached to my old desktop, HP Pavilion running Windows ME, which is not able to run the itunes software. My HP laptop is where my iTouch and iTunes software is installed.
The iTouch displays my network with good signal strength, but when I try to connect I get the "unable to join the network "NETGEAR".
Going to my router, it does not recognize my iTouch as an attached device. Why is that and what am I missing?
Thank you for all suggestions and your help.

I tried powering down the router. When it's off the iTouch does not recognize the network and then when it's powered on again, the iTouch recognizes the network. Unlike the public wi-fi spots that my iTouch responds to, where all the info like IP Address, Subnet Mask, Router, DNS etc are populated in the settings...my iTouch does not populate these fields at home even though it recognizes the network. I still get the unable to connect to network error. Could it be that my router is antiquated and can not support the iTouch? Like I said earlier, my Router does not recognize the iTouch as being attached to it.

Unable to connect to printer wirelessly

I have an Hp Officejet 7612
My computer is running Windows 7 64-bit with Service Pack 1
I am not able to connect to my printer wirelessly.
When trying to add printer, after selecting "Add network, wireless, or Bluetooth printer", my computer is not able to see printer while serching. I try to add printer manually by typing in IP address or hostname (either one), an error message occurs.
Printer wifi is on and connected to the same network as the computer.
I have restored network settings to default in order to try and fix issue.
I've tried this on a number of other computers, some running Windows 8.
I have disabled computer firewalls and computers still can't find printer.
It is as if the printer is...invisible!

Hey @chriswalkenspal ,
Thank you for taking the time to post on the HP Forums today! Hope you enjoy the experience.
I understand you have your printer and computer connected to the same network and you are unable to connect your computer to your printer.
You say you are trying to add a printer, but have you installed the printer using the device driver CD or online driver download tool ? If you haven't you need to do so and you won't have to add a printer because that is all done in the installation.
If you need the instructions on how to do so, let me know and I'll be more than happy to show you how to do download it.
Have a great day and let me know what else I can do for you.
I worked for HP.

Unable to connect to new wireless network in Mountain Lion with Photosmart C4780

I have a Photosmart C4780 and have just upgraded my imac to Mountain Lion. HP are not providing new drivers for my printer as they say it will work with Mountain Lion. I have downloaded software updates. However, I have just changed my wireless network as I have a new broadband provider but am unable to connect to it. My problem is that the set up assistant software provided which I used originally to set up does not work with Mountain Lion.
Any ideas please?

I have solved my problem, I've bought an Epson. It works perfectly. If HP can treat their customers with such disinterest and contempt I don't want to give them my money.

Unable to connect phone with pc-help

iam unable to connect my pc with the blue tooth

More information needed??
What information....read this first:
/discussions/board/message?board.id=pcsuite&message.id=160

Hi. I keep getting this message when I try to load Firefox: Unable to connect. Can you help? Thanks.

Here is the message I keep getting:
Unable to connect
Firefox can't establish a connection to the server at www.google.com.
The site could be temporarily unavailable or too busy. Try again in a few
moments.
If you are unable to load any pages, check your computer's network
connection.
If your computer or network is protected by a firewall or proxy, make sure
that Firefox is permitted to access the Web.
Unable to connect
Firefox can't establish a connection to the server at www.google.com.
The site could be temporarily unavailable or too busy. Try again in a few
moments.
If you are unable to load any pages, check your computer's network
connection.
If your computer or network is protected by a firewall or proxy, make sure
that Firefox is permitted to access the Web.

Have you checked your firewall settings?
* http://kb.mozillazine.org/Firewalls

WRT54G2 keeps dropping connection, wired and wireless

I have a Scientific Atlanta modem with WRT54G2 wireless router. Both are around 2 years old. In the past few months, I keep getting periodic connection drop, couple times a day, day on day off. I have 2 wired connections and 3 wireless connections to the router. I check with my internet provider, Cox, they say my connection is fine. So I guess it's the router or modem problem.
The funny thing is when connection drop, I cannot access any web sites via wired and wireless. However, my downloads in iTune are still running fine at full speed. I have to unplug and replug both router and modem for it to work again.
Is there a way to fix this? or do i need to buy a new router or modem?
Solved!
Go to Solution.

It's possible that Cox only recognizes the router's MAC address, probably the reason why you can't connect directly.
Anyway, try to lower the MTU settings on the router.

Macbook (10.4.11) unable to connect to one wireless network

We have one student who is unable to connect to our student wireless network. He's using a Macbook (black) with 10.4.11 and all updates. He's got a stock Airport card. We have an Airport Extreme broadcasting the network. Other students are able to connect without any problem. He's able to connect to our teacher's network without any problem.
When we try to connect his airport to the student network, it reports "There was an error joining the AirPort network 'Riverstone Students'." No further information is provided. I've tried removing it from his preferred networks, removing the key from the keychain, and reconnecting, but no change.
Any suggestions gratefully received!

Just found out a little info about my work network. We are using a SMC Network 8014 W-G broadband modem and a Linksys WAP11 Wireless Access Point, and the security is WEP. I have tried to login to the device webpage to check/adjust settings but nobody here knows the password and "admin" doesn't work. I really don't want to do a hard reset and take the chance of screwing up the network for everybody in the office (apparently it was quite complicated to set up when they first installed it, I wasn't around then). Does anybody have any other ideas? Thanks

X BOX 360 unable to connect wired or wireless.. help?????????????

Similar Messages

Maybe you are looking for