X-Fi card not detected

Just installed this card, and when I run the installer to install the drivers, it says there is no card detected. Any ideas? Thanks very much..

Solved.......used a different PCI slot, and all is good.

Similar Messages

How long it takes to repair an Apple iPad with the error "sim card not detected". The ipad is in Apple since 19 January and still has the status "Repair in Progress".

How long it takes to repair an Apple iPad with the error "sim card not detected". The ipad is in Apple since 19 January and still has the status "Repair in Progress".

There is no way any fellow user here can know anything specific about your repair status. You will need to call Apple and ask them yourself.

Z30, sim card not detected

My Z30 just few months old, sim card not detect, can someone help? thanks a lot..

Hello,
Have you tested the SIM in another device? Have you tested another known-good SIM in this device? Is there an error message? Has it ever worked?
Let us know.

PCMCIA Realtek Ethernet card not detected

Hi, I'm trying to use a PCMCIA Etherner Card with Realtek chip.
If the card it's already plugged when booting, Udev takes 180000 ms to finish and the card doesn't work. If it's plugged while booted, dmesg shows that there's a "something" at SmartCardBus but, again, card doesn't get recognized.
"Ifconfig -a" shows nothing, and I know the card works 'cause I've tryed with an Ubuntu cd and the cards works perfect. I've looked for the modules, and 8139too & 8139cp where loaded, wich I've tryed in arch and still doesn't work, It also detects the same hardware with lspci (Arch detects the Cardbus but not the realtek card, Ubuntu detects both) and lspcmcia.
Ubuntu is using kernel 2.6.27-7 and Arch 2.6.28.
hwd -e:
1217:7113 CardBus bridge: 02 Micro, Inc. module:yanta_cardbus
OZ711EC1 SmartCardBus Controller
lspmcia:
Socket 0 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.0)
CardBus card -- see "lspci" for more information
Socket 1 Bridge: [yenta_cardbus] (bus ID: 0000:02:01.1)
Socket 1 Device 0: [-- no driver --] (bus ID: 1.0)
lspci:
00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01)
00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon RV250 [Mobility FireGL 9000] (rev 02)
02:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M Gigabit Ethernet (rev ff)
02:01.0 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:01.1 CardBus bridge: O2 Micro, Inc. OZ711EC1 SmartCardBus Controller (rev 20)
02:03.0 Network controller: Intel Corporation PRO/Wireless 2200BG [Calexico2] Network Connection (rev 05)
dmesg:
int3: 0000 [#1] PREEMPT SMP
last sysfs file: /sys/devices/pci0000:00/0000:00:1e.0/0000:02:03.0/class
Modules linked in: usb_storage joydev ppdev iTCO_wdt iTCO_vendor_support ehci_hcd psmouse uhci_hcd parport_pc lp serio_raw usbcore shpchp pci_hotplug sg video output parport pcspkr ppp_generic intel_agp agpgart pcmcia dcdbas thermal evdev fan button battery ac acpi_cpufreq freq_table processor snd_intel8x0m snd_seq_oss snd_intel8x0 snd_seq_midi_event snd_seq snd_seq_device snd_ac97_codec snd_pcm_oss snd_pcm snd_timer snd_page_alloc snd_mixer_oss snd soundcore ac97_bus ipw2200 ieee80211 ieee80211_crypt tg3 libphy slhc rtc_cmos rtc_core rtc_lib ext3 jbd mbcache sr_mod cdrom yenta_socket rsrc_nonstatic pcmcia_core sd_mod ata_piix ata_generic pata_acpi libata scsi_mod
Pid: 435, comm: pccardd Not tainted (2.6.28-ARCH #1) Inspiron 600m
EIP: 0060:[<c044dce0>] EFLAGS: 00000246 CPU: 0
EIP is at quirk_h12y_1_mmio+0x1/0x26
EAX: de4fc800 EBX: c03cbdc0 ECX: de4fc840 EDX: de4fc800
ESI: c03cc110 EDI: de4fc800 EBP: df8ae400 ESP: df1b9ef4
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
Process pccardd (pid: 435, ti=df1b8000 task=df1ba000 task.ti=df1b8000)
Stack:
c02192c3 de4fc800 df8ae400 de4fc800 c0216a59 00000200 00000000 c031c93c
de4fc826 c03b3d25 00000000 00000003 00000000 00000000 00000001 df8ae420
de4fc858 00000200 813910ec 00ffffed 00000000 00000000 00000000 df8ae400
Call Trace:
[<c02192c3>] pci_fixup_device+0x63/0xc0
[<c0216a59>] pci_device_add+0x69/0xb0
[<c031c93c>] pci_scan_single_device+0x35c/0x4f0
[<c0216ac3>] pci_scan_slot+0x23/0x80
[<e0bd850f>] cb_alloc+0x1f/0xd4 [pcmcia_core]
[<e0bd4854>] socket_insert+0x124/0x140 [pcmcia_core]
[<e0bd5202>] pccardd+0x202/0x290 [pcmcia_core]
[<e0bd5000>] pccardd+0x0/0x290 [pcmcia_core]
[<c01440f9>] kthread+0x39/0x70
[<c01440c0>] kthread+0x0/0x70
[<c0104d33>] kernel_thread_helper+0x7/0x14
Code: cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc <cc> cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc cc
EIP: [<c044dce0>] quirk_h12y_1_mmio+0x1/0x26 SS:ESP 0068:df1b9ef4
---[ end trace 6fe320c81d500dc7 ]---
note: pccardd[435] exited with preempt_count 1
pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[drm] Initialized drm 1.1.0 20060810
[drm] Initialized radeon 1.29.0 20080528 on minor 0
agpgart-intel 0000:00:00.0: AGP 2.0 bridge
agpgart-intel 0000:00:00.0: putting AGP V2 device into 4x mode
pci 0000:01:00.0: putting AGP V2 device into 4x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 2 usecs
rc.conf:
MODULES=(slhc tg3 ipw2200 ac97_bus snd-mixer-oss snd-pcm-oss snd-page-alloc snd-pcm snd-timer snd snd-ac97-codec snd-intel8x0 snd-intel8x0m soundcore acpi-cpufreq)
DAEMONS=(syslog-ng network netfs dbus hal !crond cpufreq fam avahi-daemon pcmcia)
I've tryed loading: 8139too 8139cp pcmcia_core pcmcia yenta_socket rsrc_nonstatic
The bradcom is the original eth port wich I'm replacing because stop working long time ago (And I also tryed disabling it from BIOS, and it's the same).
I'm mising something that I should load or run? I've googled a lot, but people just plug the card and that's all :-P. Any idea would be welcomed :-).
EDIT: Fix title (PMCIA*)
Last edited by el_zoona (2009-01-22 07:25:00)

Nevermind...It's Kernel 2.6.28...I'm a lucky guy, eh? :-(
Booted into Arch Overlod cd and a simple lspci show my shiny new card...Now i'm going to erase my hole system (it was new anyway) and check if a Suy breaks the drivers again. In that case, i should file a bug somewhere, right?

Sound Blaster Live 24-bit PCI Sound Card and Creative Sound Blaster PCI Card not detect

Ok here is my problem. I bought a Creative Sound Blaster PCI sound card a while back and it was working fine but recently when I would boot up my computer and try to play music say off of Winamp it says Bad DirectSound Driver. When I check device manager it shows no sound card there and in sounds and audio devices it says no audio device. Now my brother believed this to be a card fault so we went to Frys and bought a Sound Blaster Li've 24-bit PCI card. I uninstalled the old drivers and installed this new one but yet it's the same problem. My assumption was that Windows XP had something conflicting so I reinstalled the OS. It found the card and I installed the latest drivers?off of this site but now it does the same thing yet again with a fresh install of Windows XP. The card has been in all 3 of my PCI slots and it will detect it for a moment but then acts like as if the card was never installed. Like I never installed a sound card into the computer. The onboard audio has been disabled for a while now but I do not know what the problem could be. I did Scan for hardware changes but it doesn't show up. Sometimes when the card is detected if I do scan for hardware changes and the card is there it will just magically disappear from the device manager as if it was never there. Even when I try to load music and I see the card is detected it will not play the music and ends up locking up Winamp to the point that sometimes will go BSOD. Now I would really like to find out what the issue is because I am planning this weekend to swap out my motherboard with a duplicate board to see if that will end up fixing the problem but I want to find out if there is any other way to fix this issue. Thank you.Message Edited by AuXoIs on 02-25-200808:28 PM

Hmm what other options is there for the bios on PCI slots?Also anything you connect to the motherboard can have oxidization (I think its that) build up on the connection. Check the connector on the card and get a eraser (Pen eraser is better) and give it a good cleaning. The connector might have alot of build-up on it and you can see it by a dark yellowy colour. I cleaned my graphics card and ram connectors after they got alot of the build-up on them. On a older computer my graphics stopped working and this fixed it. Also I went away for a while (like a month) and came back to see that my puter didn't display anything. Opened it up and saw that the graphic card had alot of corrosion? on the card connector and in the slot. Does that if you computer is turned of for a long time. Had a heck of time trying to clean the slot out. One other thing that it could be is the sound card is faulty. I had an audigy 2 and it died a while back . It picks it up and then try and use it computer freezes and the after restart it's not there anymore. Hope it's not that problem. Hope this gives you something to go by.

SanDisk microSD card not detected

Greetings,
My 8900 model is not detecting the 2 GB microSD card I just purchased for it. I have triple checked the insertion, rebooted the device, updated the software, reformatted the card on my PC, and set the Memory options to automatically detect and use a media card once inserted.
Can anyone tell me why the card is still not being detected? Many thanks!

Also keep in mind that what ever else you have stored on the phone memory will limit the amount of messages as the phone memory is a shared space.
Contacts, Images, Ringtones, Music, Calendar entries and other things stored on the phone memory limits the space left to be use by messages. Go to your gallery and see what you have stored in phone memory and try to put it on the memory card instead.
You can also try to do the following :
Menu->Gallery->Options->Memory Status->Phone Memory
You should get a break down of the usage as in :
Free Memory : x.xxMB
Gallery : x.xxMB
Messaging : x.xxMB
Applications : x.xxMB
Bookmarks : x.xxMB
Knowledge should be your Advisor when you need help.
1610»2110»8110»5110»3310»6210»7250i»6220»6230»6230i»6233
Love me or hate me, its still an obsession. Love me or hate me, that is the question. If you love me then Thank you! If you hate me then ...

After Security Update 2010-001: Airport Card Not Detected

Currently running OS X 10.5.8 on a Mid 2009 MacBook Pro.
Here's the issue. When I boot up the machine and click the AirPort drop down it tells me that there is no airport card detected. Under system profiler it says the same thing. If I boot to a 10.6 Mac OS Install DVD and open system profiler, the AirPort card is detected. This occurred after a reboot prompted by the Security Update 2010-001.
So far I have repaired permissions and repaired disk. No fix.
I reset the PRAM/NVRAM and SMC. No fix.
I booted to an OS X image on an external drive. No fix.
I cannot boot to the Apple Hardware Test (D at startup) because my company requires PGP disk encryption. I could decrypt but this would take at least 6 hours (not counting re-encrypting afterwards).
I tried replacing the extensions. No fix.
There were no firmware updates applied or any other major OS updates.
Anyone have anything else I can attempt?

anyone else see that??
Yes, Already covered in full here. Strange but no problem.
http://discussions.apple.com/thread.jspa?threadID=2310982&tstart=15

Graphics Card not detected.

I bought my laptop two days back. Its the new HP Pavillion dv6 laptop. I have a 2gb AMD Radeon 6770m graphics card installed. But my games do not detect it. Even when i right click on the catalyst center icon on the taskbar i have a tab called Mobile Intel(R) HD Graphics where i can change the setting for intel HD Graphics which come with the new intel cores. No where in the computer was i able to change the active graphics card.

You have to set the game to high performance in the ccc
for start the 6770 will not run opengl games or apps on any dv6 or dv7 61xx
look at this thread
http://h30434.www3.hp.com/t5/Notebook-Display-and-Video/New-dv7-tqe-6100-CTO-Will-Not-Switch-to-ATI-...
**Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Re: Portege Z830-11j - Sim card not detected

Portege Z830-11j I have this laptop... it is great,
However the right side drawer supposed to a SIM card is not detectable when it installed.
Is there some lack of software, or other setup required.
Can anyone help?
+Message was translated+

Do you use this notebook with Toshiba preinstalled and preconfigured Win 7 system?
Did you change something in the system configuration?
Is 3G module recognized in the device manager?
Please check this because due to missing and not installed 3G Ericsson driver, the sim module would not be recognized by system and the inserted sim card could not be handled.

PXI cards not detected

I'm using SignalExpress with a NI PXIe-1062Q chassis and the following cards:
PXIe-8360
PXI-4071 DMM
PXIe-6556 waveform generator/analyser
PXI-4110
All cards are detected by NI MAX. However when I create a waveform in SignalExpress, it's unable to see my hardware. It can see the 4071.
I'm following the correct startup procedure of booting the chassis first, then booting my PC.
Any suggestions?

Hello AidanFrost,
The reason for this could probably be that you may not have the correct drivers installed. Which drivers do you have on you computer at the moment ?

New Help Pls! Sound Card Not Detected

Hello,
I decided to re-install windows 7 because it has been a long time since I had a "clean" install. I had my Creative Labs Sound Blaster X-FI Xtreme Gamer installed and it worked fine. But after I re-installed windows 7, the sound card would not be detected.
Because this happened to me last time I installed windows 7, I wiped my system dri've (C) and re-installed windows. However, this did not fixed the issue because the card is still not detected and it shows yellow in the device manager.
In my second install, I removed the card before installing windows because I thought it would detect it after the installation but it didn't.
I have tried installing manually, but it says:
Creative X-Fi Audio Processor (WMD) not found
I am really running out of ideas here and I would appreciate it if someone could tell me how to fix this.

I just tried to move the sound card to another PCI slot, I uninstalled the devices in the media manager, turned off the PC and switched the card. I made sure there was no dust.
I also disabled onboard audio. When I turned the PC back on the computer tried to install drivers for new devices but failed. I still cannot install my drivers -.-
If it helps, the card shows as "Multimedia Audio Controller" under "Other Devices"...

Sound card not detecting digital cab

I'm having a problem getting the digital out to work on my X-Fi Gamer. I purchased the card and also the breakout box that provides s/pdif i/o via coax and digital through the /8 jack. I connect it via an optical cable to my surround receiver. I've installed all the proper software, etc, and I can get absolutely no sound.
My thought is that the card is not detecting my optical connection. In the "flexijack" options everything is grayed out and I cannot choose digital at all. In speaker set up it has the analog connections marked at plugged in (with cords coming out) and not the flexijack connection. Only the flexijack is plugged in on the card, though. Per other posts on the boards I've made sure no other sound devices are set as default, and my onboard sound is disabled completely. I'm using a creative approved adapter (the digital i/o box) with a working cable, and working receiver. Any help would be really appreciated.
I'm running windows Media Center XP 2005, by the way.

Hey MrE, did you ever get this issue sorted?
I had exactly the same symptoms recently with my new system build, and it ended up being caused by a conflict with my video card. When I booted the system using the motherboards onboard video, my ice1712 card would then be detected by ALSA and worked as it should.
I ended up moving my video card to the 2nd / bottom PCI-E on my motherboard and this got around the issue

S2110 sim card not detected

Hello!
Since day one I've got this problem with SIM card not being detected in the S2110 tablet
I received as a gift from Vodafone (branded).
Is there a way to troubleshoot this? I did some research and got to know it must be related to the modem partition. Is there a way to flash a new modem image and have my SIM card detected ?
Pls any technical suggestion and detail would be a great help !!!
Thank you in advance.
*** nothing is impossible ***

was the sim card working before?

SD Card not detected

Against my better judgment opted for a HP Omni Tab 10 instead of ipad mini. After using the tab for a month the touchscreen stopped working. I reseted the tab thinking it would solve the problem. The touchscreen started working (though I lost a buch of important documents), but again after a week it stopped responding. I again reseted the tab. However this time the problem was not solved. So I approached online HP support to get the problem rectified. The online support team kept me online for almost 2 hours and was trying to install drivers through remote support. They were unsuccessful in fixing the same. About 2 days later they asked me to visit a customer care center. The customer care center address given to me by online support staff was wrong and I was redirected to another customer center (which was in the most congested and traffic infested place in Mumbai). The customer care representative said that he would have to replace the touchscreen and that it was not in stock. After 10 days I recieved a call stating that the tab was ready. On reaching the customer care office the tab refused to start. At that moment the representative realised that he had not connected the "on" switch. Upon realisation he promptly opened the device again and connected the on switch. The device started and touchscreen was working properly. A day later when I sat down with my tab i realised the recovery drive sd card was missing. I inserted another card with media which was not detected. Even after inserting 2 different media cards it was not detected. I checked under device properties to confirm if the device had malfunctioned. Under hidden devices it showed that the particular device was unplugged.
It is really disheartening to spend almost a months salary on a device which does not have a shell life of even a year.
Furthermore it is not expected from a company like HP to bring to market such cheaply designed products.
If it had been a company like apple or sony for that matter the device would have been promptly replaced.
I would desist anyone from buying HP products ever again.
Do not buy the HP Omni tab 10!

Hi karan-7,
I have sent you a private message. If you are not sure how to check your private messages then this post has instructions that will guide you through the process.
Regards,
George
I work for HP

WS-X4612-SFP_E card not detecting

I have inserted the WS-X4612-SFP-E card in my core switch 4506.but it is not detecting.what is the problem?
Below is the show inventory of that switch.
Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-ENTSERVICESK9-M),
Version 12.2(54)SG1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Thu 27-Jan-11 11:39 by prod_rel_team
Image text-base: 0x10000000, data-base: 0x123FB194
ROM: 12.2(31r)SGA1
Dagobah Revision 226, Swamp Revision 34
CS02 uptime is 6 days, 14 hours, 48 minutes
System returned to ROM by power-on
System image file is "bootflash:cat4500-entservicesk9-mz.122-54.SG1.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected]
cisco WS-C4506-E (MPC8245) processor (revision 4) with 524288K bytes of memory.
Processor board ID FOX1321G8SL
MPC8245 CPU at 400Mhz, Supervisor V
Last reset from Reload
18 Virtual Ethernet interfaces
20 Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101

You have a Sup V while the module requires Sup6-E or Sup7-E
http://www.cisco.com/en/US/prod/collateral/modules/ps2710/ps5494/product_data_sheet0900aecd802109ea.html
Table 1.

ACER ASPIRE Z5801 Wi-Fi card not detected

Hello, After 2 failed attempts at installing Windows 10 on the Acer Aspire Z5801, I finally managed to get it installed on the 3rd attempt. However, this wasn't without problems after installation.. I found that Windows 10 was not detecting any wireless adapter, preventing me from accessing the Internet wirelessly. I tried to get the driver off the acer website (selected W7 as the driver is only listed on that OS) but that didn't work - it said it successfully installed but still wouldn't recognise the card, even after a reboot. The ethernet adapter was there (listed in Device Manager), just not the wireless card. To test whether it was a Windows 10 issue with how it handles wireless connections, I attempted to install a USB wireless adapter I had (which is usually in use by another PC) and that worked successfully after installing the driver for the adapter. This is not a solution though because the other PC needs that adapter to connect to the Internet. In the end, I just reverted back to Windows 7 and the card was detected once again. This is disappointing because another computer of mine that is much older + has weaker hardware, successfully managed to install Windows 10 without hiccups and even after installation, it runs flawlessly. So why can't Acer enable more support for other systems? The Z5801 should be perfectly capable enough of running the latest OS but due to lack of support, users of this PC must stick to Windows 7.. It's not just the driver either.. this PC suffers from other issues during upgrade and after installation. I don't know, it's disappointing. I've wasted so much time trying to install it and every time, a new problem arises.

Bump

X-Fi card not detected

Similar Messages

Maybe you are looking for