X-fi elite pro/guitar port set up help nee

Hi people, does anyone know if it's possible to run my guitar port thru my elite pro soundcard, and if so how do I go about connecting the two? Perhaps I'm missing something blindingly obvious, but I just can't seem too figure this one out.
Any help received with thanks.

Thanks for your help Sirhunter. Perhaps I could have explained my problem a bit more clearly: I can get a signal into the computer no problem; if I switch to tuner mode on Guitar Port it is obvious that there is input. Getting sound out is a tad more tricky. The normal route would be to unplug the speaker wire from the analogue out on the soundcard, run a cable from the analogue out to the input at the rear of the Guitar Port and then plug the speakers into the headphone socket of the Guitar Port and everything is hunky dory. The trouble in my case is that I have 7. speakers that take up three analogue outputs, and there is only one input on the back of the GP.
Is there a way round this, or would it be a better option to buy some amp modelling software and go direct through the breakout box and bypass the GP completely? Again, thanks for any assistance or advice.

Similar Messages

  • Elite Pro doesn't work with 5.1 setti

    Hi, recently i have changed my card from xtreme audio to elite pro
    It was working fine during xtreme audio when i set all to 5.; when i changed to elite pro, the 5. setting doesn't work.
    The center speaker sound comes out from woofer, and the woofer is working as it should..
    My only problem now is center speaker doesn't work with elite pro.. Is there any solution?
    I have newest drivers, all installed well without error; I have check all the jacks and they are well plugged..
    I have tested all the speakers, no errors, changed back to my old card and it works well with 5.
    Please help?

    For some reason, this resolved itself today.
    It still occurred with 10.10.2, and I returned to the Apple Store to have it looked at.  After checking, their assessment was that it was something to do with Yahoo servers, for that account.   They referred me to Yahoo.   
    This morning, the Inbox loaded!!! The issue is now fixed.   I hope others are seeing their issues resolved as well.

  • Need advice on optimizing the x-fi elite pro sett

    Hi,
    I am currently using SB X-Fi elite pro and Gigaworks S750. Need to have an advice especially on the THX setting optimization (bass redirection). I need to know how does this redirection work? Is it by redirecting any freq below the specified freq to the sub and the rest keep it at the sats?
    The speaker itself has a build in cross-over right? Is it possible to know what is the freq? and what is the advantage over setting the freq at THX recommendation?
    Appreciate the help.
    Thanks

    The Gigaworks have their own internal bass management like 98% of all PC speakers and you don't need to enable bass redirection on the soundcard. If you needed bass management, you would know as there would be little to no bass from yer subwoofer.
    The only PC speakers that I'm aware of which needed bass management on the soundcard was the VideoLogic Digi-Theatre speakers.Message Edited by nvidiot on 0-24-2006 0:09 PM

  • X-Fi Elite Pro, can't hear PS2/X

    Hello. I tried to search the forums, but I either searched poorly or I couldn't find a similar issue.
    Here's the problem -- I can't hear either my PS2 or my Xbox using the Elite Pro on my PC.
    Hardware:
    [The good part]
    PC does not have on-board audio for the motherboard (no need to flip a BIOS switch).
    I have the SoundBlaster X-Fi Elite Pro PCI card plugged into an open PCI slot on the motherboard.
    I installed the drivers from the CD as per the instructions. After the drivers are installed, and the reboot occurs, I can hear my normal PC sound perfectly through my headphones (I only have headphones. Speakers will come later).
    Initial hardware check - PASS.
    [The bad part]
    I plug the two RCAs (Left/Right) from my PS2 into the back of the Elite Pro exterior console.
    I plug my Xbox into the back of the exterior console as well, only this time into the optical input using Monster cabling.
    That's what I have set up. No matter what I've tried as far as configurations go on the software side, I cannot hear these two devices. Either through the fancy-graphics Creative Console Launcher, or from XP (SP2)'s Control Panel > Sound options... I just can't hear anything (Playback or Recording options, Mute boxes, volume sliders, etc). I've also tried flipping the Aux2/Phono switch on the back of the exterior console and then trying everything I already tried all oer again.
    I'm at a loss as to why I can't hear anything. I went to the store and picked up a RCA-to-Stereo converter and plugged the PS2 into the Microphone/Line-In port on the exterior console, and I could hear the PS2 through that. There are several reasons why that is an insufficient fix to my problem: ) I'd like to hook up the Xbox and PS2 at the same time. 2) I play World of Warcraft, and need the microphone slot freed up so that I can speak to my guild, and not have to crawl behind my machine every time I want to switch what I'm doing. 3) I paid for the Elite Pro specifically so that I could set all this up.
    If anyone has any suggestions, by all means let me know!Message Edited by Gimpifier on 09--2006 09:48 PMMessage Edited by Gimpifier on 09--2006 09:49 PM

    Ok, as you see in the picture, there are several mixer stri
    ps.
    All of them are related to the upper tabs. So:
    The Inputs tab bares all the available inputs on your rack and PCI card (just Line In for the latter).
    The Multi-Channel Wave tab bares all the outputs available on your rack and the PCI.
    Those two tabs are the most important right now.
    As I noted earlier, the problem occures either from a mute selection in the Auxiliary 2 strip or a 0% setting to the volume slider of the same strip. Otherwise, you are routing the Aux2 to an output not connected to your speakers. From what I see, no "Mute On" is apparent and you are routing every input to Front L/R Output. Have you tried plugging your headphones to Front L/R and select "2/2." as speakers?
    You should also select the monitoring to "Recording" and not to "Playback" (found at the blue field, bottom right). This will enable you to see the input level for your recording source (Aux2 in your case, correctly selected by you).
    Your speaker selection is set to "Headphones". Are they connected to the front output?
    It might be better to do some troubleshooting. So:
    What is the real problem?
    No signal from Aux2 input?
    No signal from the headphones output?
    You say that:
    Gimpifier wrote:
    The RCAs are li've and working. If I use the Stereo adapter, I can plug them into Mic-In/Line-In and I can hear them if I swap to Line-In. The problem is getting them to work as they are intended, so that I don't have to monkey behind the PC when I want RCA audio.
    Can you be mor specific on this? Li've and working? You mean li've from the PS2? Get them to work as intended?
    Message Edited by Chastity on 09-3-2006 08:46 AM

  • X-Fi Elite Pro - Recording from the Phono Input Prob

    Kit:?
    Vista x64
    4GB Ram
    Q6600
    X38 Mobo
    X-Fi Elite Pro
    Audio is taken via?Digital Output (not the optical one) from the External box to a Sony Cinema Amp.
    Have installed using the Vista X-Fi CD and updated to the July 2008 drivers.
    Problem:
    Unable to record from the Phono input on the external breakout box, in fact only the Line-In on the actual card seems to work, but when recording via the Creative Entertainment Console the recording has what sounds like reverb applied to it. Recording via Vista's Sound Recorder produces a clean sound but is in WMA and very low quality.
    Other Obvious Problems:
    Have to manually select the Input port via Vista's Sounds Panel, by setting the required input as 'default device'.
    Headphone socket on the external box doesn't anything coming out of it.
    Question:?
    Has anyone sucessfully recorded via the Phono input on an Elite Pro under Vista x64, and if so how
    Thanks.
    Message Edited by 0idsjagf on 08-07-2008 2:56 PM

    Huhu, right-click onto the window where all devices like microphone or speaker output are listet (record, playback) (Controlpanel " sound") Then you have the option to enable "show deactivated devices" maybe then the phono input is available to your needs.

  • TV/ SKY Digital Sound Through MY X-FI Elite Pro and Gigaworks s

    Hi i am trying to find out if i can get sound from my tv/sky digibox to pass through my gigaworks s750's.
    I have just got hold of a new Sony Widescreen TV and a sky digibox both seem to to have audio out right and left on the back of them. On the computer side of things i have a X-FI Elite Pro and the Gigaworks S750's.
    Im not sure about all of this so was hoping somebody in here could help.
    Any Help on what i need to do or buy would be great
    ThanksMessage Edited by Effigee on 2-5-2005 0:25 PM

    <SPAN>Hey man, thanks for pointing me in the right direction! I started messing around with the Phono 2 dials on the unit and was having no luck what so ever. I then wanted to try my microphone to make sure that it was still working from all the changes I had made. Well, when I hit the record button and talked into my mic it showed something being recorded, so I knew my mic was still working... But.... when I played the recording, It was the recording from the T.V.!!! At this point I knew I was close to getting this issue solved.
    <SPAN>
    <SPAN><SPAN>I ended up having to open my "Sounds & Audio" controller within the Windows XP Control Panel and then going to the volume section of the XF-I card and then going to file, properties, and then check the "Phono 2" port off so that I could see it listed with all of my other volume and sounds controls. I then un-muted it as you said and Bam!!!!!!! Guitar Hero on my PS2 was pumping out at my full 500W!!!! I nearly went death from the experience, but it was very gratifying!!!
    <SPAN>
    <SPAN><SPAN>Thanks for your post. It really helped to point me in the right direction. I'm now thinking of digitizing all my vinal records now into MP3's too! Thanks again man, you?re the bomb!
    <SPAN>
    <SPAN>Jeep

  • Strange Line In problem with my X-Fi Elite Pro. Stereo sound comes and goes

    I have an X-Fi Elite Pro with latest drivers installed. Everything works fine, except for the Line In port in Entertainment mode. I have an AverMedia TV/FM card and its audio output (stereo) is plugged in my X-Fi's Line In/Mic In (PCI). The problem is that I get sound only from the right channel but not from the left one, so the sound comes out in mono. From time to time, I get to hear in stereo (both channels) but it seems a random event. This input works just fine in Game and Creation modes btw.
    Stereo sound from this particular input comes and goes in random order and sometimes I get about 50% on the left and 00% on the right channel. Sometimes, left channel volume fades in and out slowly. I already did some troubleshooting such as set Line in/Mic In/Digital In to "Line In/Mic In", speaker diagnostics, checked it in Game & Creation modes, turned to default values and so on but I still get this problem.
    Seems pretty wired. A ghost in the machine! Creative products never seize to amaze us!

    Soo...your're calling me stupid? Well, perhaps your right, but then again, I might have a point!
    Read my post again.
    If you still think it's too low with SVM enabled and everything is turned up...then I'm affraid you're out of luck and might consider buying another speaker set, if it's a major issue to you.

  • HP Officejet pro 8500 won't print and keeps asking for a proxy setting. Help.

    HP Officejet pro 8500 won't print and keeps asking for a proxy setting. Help.

    Hi,
    Can you confirm that you have an Officejet 8500a or Officejet 8500? On the 8500a model, you can set the networks proxy address and port setting from the front panel of the printer (setup>Webservices setup>proxy). If you are unsure what your proxy settings are you'll need to contact your network admin. If your network uses a proxy users name and password for all devices, you need to enter this information along with the proxy address and port in the printers embedded web server. Type the products IP address into an internet brownser window (printer must be connected to the same network as PC). Select the network tab, and than look for the proxy settings option. Enter in the information and click apply. Once the networks proxy information has been correctly inputed into the embedded web server, try printing again. If unsuccessfully, you might try reinstalling the printer software after uninstalling it. Hope this helps!
    I was an HP employee
    Reminder: Please select the "Accept as Solution" button on the post that best answers your question. Also, you may select the "Kudos" button on any helpful post to give that person a quick thanks.

  • What are the flat frequency settings for bass & treble knobs on X-Fi Elite Pro?

    Ok, I have the X-Fi Elite Pro and I need to set its bass & treble levels (volume control panel) to a flat frequency response setting. I noticed that the default value given by creative is 50% for bass level and 50% for treble level. So, what is the flat frequency response setting for bass and treble knobs? 0% or 50%?
    Kind regards
    Message Edited by Hyperion on 11-14-2008 08:26 PM

    Ok, I get the picture. The reason why I asked this question came up when I bought a new set of monitors (the Edirol MA-15DBK). I found out that after changing speakers (I had a set of Philips SPC-3208) the new ones were set to 0% boost/cut for bass/treble, but the sound came out quite bassy in an almost irritating level. So, I thought that maybe my card's bass levels were somewhat boosted. I guess now some lower frequencies are revealed, so I have to take care of my room acoustics. However the reviews for the Edirols gave low bass levels, so this gets more complicated. I am still in a 30-days trial, so maybe I will have a look at the Gigaworks T40 series II and I'll see what happens then...

  • 1820M or Xi-Fi Elite Pro with Home Studio XL - Please advise

    Setting up a system
    Already have Home studio XL
    Could you give me some thoughts on the 1820M or Xi-Fi Elite Pro?
    The good the bad and the ugly.
    Seems like there is a lot of bad and ugly out there

    If you look a little bit around in the forum, you will find the answer very fast.
    At the moment all the creative X-Fi cards are only able to deli'ver stereo sound through coax and optical cable. The only way you will get DTS is, if you use the digital sound from DVDs via PowerDVD, but that 5. sound comes not from the soundcard, it is directly from the dvd dri've and will just your soundcard as a walkthrough.
    The only soundcard I've seen atm, that is able to handle 5. digital sound with X-Fi features is the "Auzentech X-Fi Prelude". I couldn't test the soundcard yet, but will buy it probably very soon.

  • Connecting Guitar Port - HELP!

    Connecting Guitar Port - HELP!" Hello,
    I have just purchased Guitar Port and wish to find the simplest way to hook up.
    I have a <span class="mainlink">X-Fi XtremeGamer Fatalty Pro Series sound card with Logitech 5. speakers.
    If you follow this link to the manual and go to page 22 you will see their instructions: http://line6.com/data/l/c0a8090bee7b...%20English.pdf
    I want to have the sound go through my speakers and not have to crawl behind the computer and mess with the cables everytime I want to play guitar.
    Thanks!!!

    also note:
    http://www.thehangtime.com/gb/gbfaq2.html#pluginguitar

  • 5.1 sound X-Fi elite pro and DTT3

    Hi all?Ok, so I have an X-Fi Elite Pro, and the DTT3500 speaker setup from Creative. Both very expensi've where I li've. I could get 5. sound from my SB Li've! 5. digital, but no such luck on the X-FI. I've read all the posts, but when speaking to Creative tech support they tell a different story. I know I can get 5. (supposedly) from DVD etc. via co-ax or optical. How do I get 5. from other apps (such as VideoStudio) or games (BF242, etc.) that do not output DD or DTS?I've tried flexi jack to DIN (from card rear panel to the speaker amp), DIN to DIN (from break-out box to speaker amp) and 3 x 3.5mm stereo to DIN (from card rear panel to speaker amp) Nothing works. I get headphone sound obviously, and can get plain stereo sound (although I didn't get this setting right for optical; works with co-ax though)?(excerpt from tech support mail)
    To assist you, i would suggest to connect the DDT3500 to the soundcard using the 3.5mm jack and the DIN Cable provided directly to the soundcard through the Digial In and DIN Socket.. enable the "Bit-Steam off" in the Audio Console, 2. select " Digital DIN" on the DTT3500 FacePlateIn case if you need any clarification, please do not hesitate to contactus.(/end excerpt)?I have made up a cable with 3 x 3.5 mm stereo jacks > DIN and got no sound at all from this. Tried all my solutions with digital I/O both on and off.?This is all very limiting, as apart from games that I'd like to enjoy as they're meant to be played, I also do video editing and need to proof my surround mixes. Not very happy Creative. Even the tech guy where I bought the card assured me it would work with 5....

    I have never installed the updated applications available in the download page... just applications and driver for Vista 64bit inside the cd and i updated the driver with the latest one. Anyway, I: Reformatted and installed Vista.
    Installed Chipset Drivers.
    Installed Video Drivers.
    Downloaded and installed JUST the latest SB drivers and i have that **bleep**-ing error window...Guys, it's 2 years i try to install Vista...Have i to destroy this sound card If i have to change it, i'll never buy another creative product in all my life (and till today i have bought 3 sound cards, 2 webcam, 4., 5. and 2. speakers for every computer we have in the office...). Thanks p.s.What is the DMLL.exe service, please
    If i enter in the "Task Bar" is visible... if i close it and i restart the computer i find it... How can i delete it forever

  • XFI Elite Pro to Inspire 5500 speakers, no rear so

    I have an xFI Elite Pro and some Inspire 5500 Digital Surround Sound speakers. If I initiate a test from the remote that controls the Speaker's "brain" I get all surround points working just fine, so I know they are connected properly from there. From the "brain" I have the /8th" cable that came with the speakers for a digital connection to a soundcard connected to the flexjack on the back of the soundcard part of the xFI and it is set to Digital I/O. Whenever I initiate a test from the Creative Software, when it says "rear right" and "rear left", it comes out the front speakers. I have the CMSS turned off . I have the decoding turned off on the sound card cause the speakers take care of the decoding. What am I doing wrong? Please help, thanks.

    Well,
    I went back to gigabyte.com.tw and this time, there were new BIOS available ... I still don't understand why they weren't there yesterday ..
    Anyway, I updated to F6 (latest version) and ... sound is still very low, crappy, crackkkkking and so on ..
    I'm gonna throw this through the window :'(

  • Apple TV issue-I have a Pioneer Elite Pro 1130 with a PRO-Ro6u Media Receiver. I cannot get my new Apple TV unit to work on this TV no matter what I have tried. No Video

    My new Apple TV unit (3rd generation) will not work with my Pioneer Elite Pro 1130 tv. The TV has a PRO-R06u Media Receiver. No matter what I try, I cannot get anything to come up on the screen. No Video and No Audio??

    Try cycling AppleTV resolutions with the remote using the tip for 'black screen recovery' here:
    http://support.apple.com/kb/ht3176
    The set is quite old now, does it support HDCP?

  • Own an X-FI Elite Pro - Getting what sounds like a CD skipping and some distortion

    Interesting I have had this card for some time now...and I never experienced any kind of distortion...popping...click noises...or anything that the majority of people here have been complaining about. I though I was one of the lucky few...that has all changed.
    I started playing some BF2 the other day...and of course have the in game audio settings set to ULTRA to and X-FI to make use of my XFI 64 megs of RAM...anyways, this is the same setting I have had in BF2 since I've owned the game and have had my XFI - Elite Pro.
    Anways, there I am playing my game when all of a sudden from time to time I hear what sounds like an audio CD skipping! I thought at first it was just me or the game...but no...it seems to happen more often than it use to! Like its getting wores! It cleary sounds like an Audio CD skipping!
    another thing I started to notice is when playing MP3s and such.... I can hear distortion in the background! Its a bit hard to explain but what it sounds like the distortion isn't in the actual audio mix...almost like background distortion!
    to test I would play the same audio track on my home theatre system and to my dismay... I heard no distortion...so that would label my XFI Elite Pro as the problem.
    a couple of things to note:
    st.. I have 2 fans hooked up on the same rail on my PSU that connects to the XFI Elite Pro. The fans have fan controlers as well... I haven't tried this...but its possible that since the fans are hooked up to the same wire as my XFI is...its possible I may be getting some electrical interference with them.
    2nd... I just updated to the latest BETA drivers released by Creative. This is where I first started to notice the problem.
    I have yet to dry difference drivers or remove the fans...however, I do believe I am finally experiencing what many other have been since there purchase.
    I paid a **bleep** pretty penny for my Elite Pro and deffinitly EXPECT it run PERFECT!
    deffinitly unhappy thus far.
    I do have an Nforce based chipset. As well as an ASUS A8N32-SLI with the most recent BIOS update.
    Like I said before, I am just now getting this sounds...its possible it could be the BETA drivers, I will keep you all posted.
    For the mean time, anyone have any insight or opinions for me?
    thanks in advnace!

    no ideas huh?
    is this the same stuff everyone else is experiencing?

Maybe you are looking for

  • Can I manipulate data in a table maintenance view (SM30)?

    Hi Everybody, I have a "z" transparent table with 3 fields: Field 1: User Field 2: Name Field 3: Address In its maintenance view (SM30) I want next: When I capture the "User", I want to populate the "Name" and "Address" automatically. (Obviously with

  • How do I get iTunes Match to recognize my IOS device?

    I just subscribed to iTunes Match thourhg itunes on my iMac desktop computer. I have confirmation that there are more than 200 songs available in iCloud. Immediately after subscribing I was able to listen to music on my iPad. Today, however, when I a

  • Question about the ability of Genius Bar to help with outside software...

    Hi I wasn't sure where to put this, but here's my question. I'm having a problem with the Sims 2 on my Macbook and I was wondering if I go to the Genius Bar will they be able to help me or are they strictly hands off when it's not a direct Apple prod

  • Using Digital Personnel File for HCM Forms & Processes

    Hi, We would like to use Digital Personnel File for HCM Forms & Processes to save forms and attachments using record case management. For this to be done record case management needs to be customized. Can you provide the steps for record case managem

  • Account Relationships. Is it possible to do bulk imports?

    Hi, I would like to know if it´s possible to import csv files with information about Account Relationships. I need to create different types of accounts and then I need to import relationship between them (For instance: Company A will be a Suplier of