X-Fi Titanium PCI-e making high pitch squeal on Windows 7 with HPET enabled

Two days ago, I tested an older Radeon 4800 to see if it still worked. Long story short, some how I screwed up my integrated sound (Realtek). I reinstalled Windows last night, and after several hours of hair pulling, still wasn't able to get it to properly play sound at all. I disabled the on board audio in the BIOS, installed my X-Fi Titanium Fatal1ty Professional PCI-e I had sitting around, and finally had sound working again (through the X-Fi). Sound was fine using the default Windows drivers, however after installing the Creative drivers, it's constantly making a very high pitched squeal. The squeal doesn't change at all, and it's constant, if I had to guess I would say it's at the very or near the very end of my audible hearing. This was the same story when I first installed the X-Fi card when I first built the computer one and half years ago, which I eventually removed a few weeks later to simplify my build and stuck with the on board audio. Back then, I figured out a way to get rid and it involved disabling the High Precision Event Timer (HPET) in the BIOS. I did the same today and it removed the squeal, but I'm wondering if there's any way of getting rid of the squeal without disabling the HPET. What confuses me is why the Windows sound driver didn't squeal but the Creative one did. Windows 7 is fully up to date, as are the drivers.

When installing the Dolby and DTS connect packages, you need to right click each and choose to install them in VISTA compatibility mode. Then they install just fine.
As far as your driver issue.........
do a search for DRIVER SWEEPER from guru3d and that will uninstall your driver and hopefully put you back to a good reinstall. Also inside your driver folder you can look for utility called CTZapp that will uninstall all traces of that driver so that you can reinstall it properly.

Similar Messages

RMAed 4890 making high pitch sound in game

MSI P55-GD80
I5 750
Cosair dominator 2x2gb
MSI 4890 cyclone
win7 64bit
ocz 700w
just got RMAed 4890 back
it's making high pitch sound whever I start gaming
did have this before RMA, when it was working
I remember this sound from back in the nvidia 7xxx/8xxx series, remember reading somewhere it was normal for cap to make this kind of sound?
not sure....

That sound can happen on video cards and is usually generated by some coil on the card when the card si heavy loaded .I have it on my 4850 and in 3D Mark 03 on my 5770.Never had it on my previous Nvidia cards though.You can have that with your PSU too.If your card is performing ok don t worry about it.Try and use V-Sync ON in driver control panel ,it may fix the anoying sound ,at least in some games.

Bazaar high-pitched squeal/fuzz noise in iTunes when scrolling.

System info:
I'm using iTunes 6.1.3 on Windows XP Pro, and I'm wearing headphones (i don't have regular speakers).
Issue:
I noticed that if I click and hold down the scroll bars in the Library in iTunes (the scrollbars for Genre, Artist, and Album), I hear a faint high-pitched squeal or fuzz noise coming into my headphones. (If I scroll through the songs themselves, I do not get this noise. It's just the three above-mentioned scroll bars). Since it's pretty faint, I only hear it if nothing else on my computer is sending out music or noise (or only if the noise is also very quiet at the time). As far as I recall, I don't remember hearing this in conjunction with any other program.
Question:
Has anyone ever heard of such an issue? It's not really a big deal, but it does make me rather curious to know what's causing it. Try it on your own computer and let me know if you have the same issue. Could it be a sound card thing? But then why would where I click in one particular program have anything to do with it?
Example file:
If you'd like to hear what I'm talking about (Since you might be tempted to think I'm making this up), I created a wave file recording of it. (I didn't want any mp3 compression to confuse the matter, so that's why it's a wav. Not that I know much about that sort of thing... but just in case.) I uploaded it to here: http://aranel.alasse.googlepages.com/itunessqueal.wav (Sorry it's so big... 5.3 MB... Obviously because it's a .wav file. It's a little over 30 seconds long. )
Process of making example file:
I recorded it using Audacity (which is an open source program that can be downloaded from sourceforge.net). In Audacity, I set the recording/input "channel" to be "Wave Out Mix". I turned the Wave out volume and the master volume all the way up, then pushed record. (Turning the Wave volume up caused additional fuzz, so concentrate on the contrast between the sections of the recording to hear the actual sound I'm referring to.) It's a pretty quiet track, so you'll probably have to turn the volume way up.
It's a 30+ second clip. Here's how the seconds break down:
For the first five seconds, I just did nothing.
From seconds five through 10, I clicked and held down the Genre scroll bar in iTunes.
From seconds 10 through 15, I did nothing again.
From seconds 15 through 20, I clicked and held down the Artist scroll bar in iTunes.
From seconds 20 through 25, I did nothing, once again (I kept doing this so you could hear
the difference).
From seconds 25 through 30, I clicked and held down the Album scroll bar in iTunes. (Notice that this one seems to be slightly higher in pitch than the noise from the previous two scrollings I did.)
The last couple seconds, I did nothing again.
More weirdness:
Changing the volume on my computer (both the master mix, and the wave out mix, and any other mix that exists (e.g. line, microphone, CD Player, Mono out, etc.)), or even MUTING the volume of any of these mixes does not make the sound go away or change in volume at all! It's always at the same volume no matter what I do. I can only make it go away if I unplug my headphones (remember: I don't have regular speakers. If I did have those, unplugging the headphones might only change where the noise is heard.). Changing the wave out volume only affected the recording (which is why I turned it way up. If I turn the wave out volume all the way down, then push record, I still hear the noise coming from iTunes while I'm recording, but if I play the recording back, the noise is gone.
Very bazaar...
Any input anyone?
Windows XP Pro

Called Apple support, they said they do not support the use of iPods in cars, they may have sold you your car kit, but they dont support it. So buyer beware. I have three cars, I upgraded my Nano to 1.1, which is the latest, didnt fix it. I went out and tried it in all three cars, squeals in the Toyota (with Monster Cassette Adapter to Original Radio, hisses in the Nissan (with Audio 3.5 cable to audio jack to after market Sony radio), and works fine in old Mercury (with 3.5 cable to old JVC with audio jack).
So I better take care of the old Mercury.

High pitched sound - something to do with internal microphone ??

Suddenly my Powerbook has started emitting a high pitched sound through its speakers. You know one of those high frequency ear-blowing sounds when a PA system is being set up and the mic is getting tested and the amp's turned up too loud?
I'm not sure exactly what I was doing when it started, but I think I was making or receiving a telephony call via iChat. During or just after the connection process (which didn't work for some reason but that could've been a problem at the other end), this high pitched squeal started. I can get rid of it by turning down the output volume - the squeal disappears but that of course turns all other output sound down as well. The sound disappears when the volume is turned down about half way.
But...even if the sound is turned down half way, if I put my hand over the left speaker, the sound comes back. No sound comes back if I place hand over right speaker. I assume then that the inbuilt microphone is under the left speaker area, and this has something to do with the inbuilt mic.
The only other thing that's happened in recent times is that I used this Powerbook's audio line-in port to record some sound from an audio casette recently. I used Audio Recorder 2.0 for this. I can't imagine this has been the cause, but thought I'd better mention it. If I go into the Sound Preference panel, I can stop the squeal by changing the sound input device from internal microphone to Line In.
Anyone have a clue as to why this is happening and how iit can be fixed?
Many thanks, Steven

Hey, great suggestion Burn. It prompted me to look at iChat preferences, since that was the only application that I've had open which might engage the internal microphone.
Within iChat Preferences, I clicked on the 'Video' icon, and for the 'Microphone' setting I saw that 'None selected' (or something like that - that option has gone now?) was in place. So I changed the setting to Internal Microphone. The whistle or screech was still there. Then I changed the setting to 'Line In'. No more screech!!
A good result, but is this the way it's supposed to be? Does having the setting as 'Line In' mean that I have to plug headphones in whenever I want to use iChat for internet telephony? Unless I manually change to Internal Microphone, but then I suffer screeching again?
Cheers, Steven

High pitch squeal when turning up volume and an echo sound

I have never gotten good audio from my computer......any time I want to watch or hear something I have to turn it up to about 35 before I hear anything and then a deafening high pitch squeal happens that makes it impossible to listen to anything.....if I plug in my headphones there is so much feed back with a horrible echo sound that I cant stand to listen for long.....I want to know if there is anything I can do to get decent sound from this laptop. tia

Hi stephenvy17,
Welcome to the HP forum!
Thank you for your inquiry, I will do my best to assist you.
I understand that you are experiencing a difficulty with the sound on your computer. When posting it is very beneficial for you to provide the exact model of your computer and the operating system you are running. How Do I Find My Model Number or Product Number?
If you are running Windows 7 or lower you can run MS Fix It to help with this issue. If you are running Windows 8 or 8.1 you have a built in troubleshooter,
Press the Windows key +C to open charms
Type troubleshoot audio and follow the on screen prompts.
You can run the HP Support Assistant to aid with resolving issues and updating drivers. If this has not helped, please provide the information requested.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

High pitched squeal noise and low end rumble RME Fireface 800 Macbook pro 2011

Hi there,
I just updated Mac OSX Snow Leopard and my Fireface 800 has started emitting a high pitched squealing noise when turned on and connected via Firewire 800 cable.
Also my 17" Macbook pro requested a hard reset last week for the first time, after this problem began.
When my subwoofer is connected, a low end rumble is emitted at the same time as the squeal, and persists until turned off and on again.
Any ideas?
Thanks
Robin

Hi there,
I just updated Mac OSX Snow Leopard and my Fireface 800 has started emitting a high pitched squealing noise when turned on and connected via Firewire 800 cable.
Also my 17" Macbook pro requested a hard reset last week for the first time, after this problem began.
When my subwoofer is connected, a low end rumble is emitted at the same time as the squeal, and persists until turned off and on again.
Any ideas?
Thanks
Robin

High Pitched Squeal CPU

I have a High Pitched squeal that is coming from my lower CPU (?)
Whenever the the "Processor Performance" is set to "Highest" it squeals and squeals and squeals. Like slow nails on a chalkboard! It's driving me nuts, to say the least.
When it switch it to "lowest" it goes away.
Perfect example. Google Maps-- I hit satellite and the squealing goes crazy when the aerial photo appears.
I've scoured the boards and found posts with same issue, but people think its a fan, when it isn't.
My question is... What is this annoying noise and what can I do?
Thanks in advance.
RJ

And it's still doing it.....
What automated task does the iphone do every hour which causes this to happen?
Have wiped the phone several times now, kept it turned off for hours, turn it back on and beeeep 10 seconds before the hour, every hour.
Does it while on charge, does it when headphones are plugged in or not, does it when all apps are closed, wifi off, bluetooth off, every single setting I can find, turned off......
Someone help, please.

USB drive causes high-pitched squeal...

I have the K8N Neo Platinum and when I plug my Lexar 128mb USB 2.0 drive into my back ports, a high pitch squeal emits from the motherboard.
The sounds actually stops when data is being passed through it, or when the power to it stops when I opt to safely remove it in the control panel icon. Anybody know how to stop this problem?

If you can't solve your issue and no one in the community can help, contact support to speak with a tech support agent at (800) 631-3811.
- Peter

High pitch squealing noise

After printer sits idle for awhile there is a high pitched squealing noise. At first you don't notice it and then it becomes so annoying as a light background noise I have to turn off the printer until I need it again.

Hello Bernina,
Welcome to the HP Forums.
Typically when a printer makes any kind of unusual noise, it has to do with a power issue or a lack there of.
Please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
If the troubleshooting does not help resolve your issue, I would then suggest calling HP's Technical Support to see about further options for you. If you are calling within North America, the number is 1-800-474-6836 and for all other regions, click here: click here.
Thanks for your time.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

High pitched squealing from SBS

Ok, I purchased a set of these speakers yesterday (Sunday) and the front 2 speakers make a very high-pitched squealing sound. It's only happened today and I've switched the left peakers around and the sound persists. I has a set of Creative 2.0 speakers and they had no issues so what's going on? The sound card is a Sound Blaster Audigy SB394.

n&b,
What are the differences between the noises that the fan and the hard drive make?
Well if it's louder if you stick you ear near the vents that blow air out the back then it's probably the fan. If not HD.
You might post an audio recording of the noise.
Can you recommend a backup drive?
Well normally I'd send you here:
http://www.macsales.com/
But if your drive is dying you need to back up ASAP so go anywhere like BB:
http://www.bestbuy.com/site/olspage.jsp?skuId=8295196&st=st305004fda1e1&lp=1&typ e=product&cp=1&id=1172277308863
Richard
Message was edited by: spudnuty

IPod Nano won't turn on and emits a LOUD high pitch SQUEAL

Hello,
I have an old (but great) 1st gen Nano that has been kicked around fora couple years.
Now it won't power on, it's not recognized by my Mac, nothing.
Whenever I plug it in (There is no battery in it), it gives off a loud, high pitched squeal, it's quite horrendous. I unplugged the screen and it still squeals. When I reset it the squeals stop for a second, I can hear it make a click in the headphones like it normally does when working, and then it squeals.
When the screen was smashed in this iPod it did the same thing, but the screen isn't smashed this time.
Thanks,
Tanner.

Leave it charging for at least 2 hours, till the full charge icon comes ON.
Reset the iPod -Press Menu and Center button simultaneous for about 10 secs till the Apple logo comes ON
Refer to this Apple support article on Step 2.(RESET)
http://www.apple.com/support/ipod/five_rs/classic/
Release the button and select your prefered language.
If the above doesn't work then do a disk diagnostic as posted earlier by tt2.
https://discussions.apple.com/message/17028567#17028567
As the RED X meant your Hardisk is having a stroke.
Good Luck!

U300 - High Pitch Squealing

I am having a very odd issue with a friends U300 laptop. She has been complaining that when she turns the laptop on, it makes a high pitch squealing sound (noticeable from rooms away) and will only boot into safe mode. I took the laptop from her brought it home, and it turned on normally for two days and booted fine into windows. I gave the laptop back to her and she took it home and turned it on and low and behold it started the squeal again and only booting into windows in safe mode. She is a very intelligent woman so I know she is telling me the truth. I had her try a different power outlet and same thing happens.
I am wondering if any one else has experienced this issue as I cannot get it to happen for me.

It was not a squealing noise but other ailments that would vanish when the owner presented the machine to me to show me she wasn't crazy. But after she left the ailment popped up.This has happened a few times.
Anyway I digress; if its not the hard drive (which would work not at all if it made those noises I would think) its a cooling fan that must be replaced. What else could it be? There are not that many moving parts....
Break out those tiny screwdrivers..

Fan ( I believe ) now making high pitched sounds ...

Hello,
I've recently noticed that upon startup, sometimes ending after long periods of use, the fans seem to be making a high pitched and sometimes choppy sound. I assume the fans due to the sound coming mostly from the upper middle of the keyboard.
My warranty is up in October, so I was wondering what else I could be on the lookout for within the next couple of months that may warrant a trip to the genius bar - any other symptoms of fans going bad etc ...
cheers

Does it sound like this:
http://www.youtube.com/watch?v=8FwL0ibhEFY

IPod making high pitched buzzing noise

I've had my iPod over two years now, maybe three but it's always worked and hasn't had any problems. The other day I connected it to a cheap second hand Pod station that a friend had been lent. The pod station wouldn't play my iPod and nothing much happened so I resolved that my iPod was just too old to work on it and took it back out again. When I tried to turn on my iPod afterwards it wouldn't do anything so I thought that the battery had probably just been drained out and it would be fine when I took it home and connected it to my computer.
However when I did so the iPod did not appear on the desktop or in iTunes and the screen remained blank. I kept trying but the same would continue to happen and I began to notice that now whenever I plug in the iPod a very high pitched buzzing noise comes from the iPod which scares me a little as it's so unusual. I have tried resetting and pretty much all of the suggested solutions on the apple site and in other discussions but none work. Nothing seems to work and the iPod does absolutely nothing. Is there anything at all that I can do or does this mean that my iPod has simply finally had it?
I wouldn't have thought that just a cheap Pod station would be enough to cause such a major problem with it.
Any help would be very much appreciated please!

If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
http://www.rapidrepair.com/shop/g4-ipod-parts.html
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
Spank your iPod
http://www.youtube.com/watch?v=3ljPhrFUaOY
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

P5800 making high pitch noises some times, and clicking noises (not so loud though)

hi, i bought the creative p5800 just recently and extended the cable wire by buying monster 6 guage speaker wire. anyways, sometimes it just makes high pitch noises when im not playing any sounds, and I was wondering if anyone could help me on that problem. thanks a lot.

MikeFar,
You will need to discuss the available option for repair with the respecti've region support. They'll be able to advise you in details.
Americas Customer Support
European Customer Support
Asia Customer Support
Jason

X-Fi Titanium PCI-e making high pitch squeal on Windows 7 with HPET enabled

Similar Messages

Maybe you are looking for